Search Documents

By Lyle L. Marsh, David L. Douglas

CORRELATION was made between the heat treatment and hardness of three U-Ti alloys ranging in composition from 8.5 to 50 atomic pct Ti. The following important observations were made: 1) A direct quench of y U-Ti solid solution resulted in the formation of a hard martensitic phase in low-titanium alloys. 2) Subsequent tempering initially increased the hardness by the precipitation of a fine dispersion of U2Ti; further precipitation of U2Ti with tempering time eventually resulted in softening. 3) High-hardness levels were obtained also by isothermal transformation of an 8.5 atomic pct Ti alloy at 400º and 500°C. 4) The crystal structure of the phases present at the solution-treating temperature (one region in the phase diagram excepted) and the temperature within a given phase region affected the hardness of both quenched and isothermally transformed alloys. Introduction It has been known since 1887 that the mechanical properties of metals were dependent upon their microstructure. Sorby pointed out in that year that annealed gray iron castings were softer than chilled iron castings by virtue of the graphite which had replaced hard cementite in the microstructure. Over the years, interest has increased in the effect of microstructure on the mechanical properties of metals, and now high-strength levels may be achieved by bringing about the dispersion of a second phase or by other microstructural adjustments. The nature of a second phase in an alloy strongly influences the properties. For example, the size, shape, amount, and distribution of a second phase plays a very important role in the ultimate properties of an alloy. Microstructural control is achieved by heat treatments. Hence, any alloy system of potential use should be understood in terms of its response to heat treatment and the resultant effects upon the properties.

Jan 1, 1958

By AIME AIME

NAPOLEON'S dictum that an Army travels on its stomach has not changed in this present war, but the things an Army's stomach calls for would be more than strange to Napoleon. Today one of the main articles of diet for the mechanized army is oil and gasoline, and the chief and most efficient source of 'apply overland is the pipe line. It was a flexible 4-in. pipe line that supplied the voracious appetite of tanks, trucks, jeeps, and planes across the North African desert. and it is the 1800-mile pipe line from Calcutta to Kunming, Yunnan Province in China, the longest in the world, that supplied oil and 100-octane gas for the trucks, tanks, Jeeps, and planes fighting on the Assam-Burma-China front in recent months. Completion of this approximately 1800-mile pipe line to China over rivers that had never been bridged, over hill that towered 9000 ft., and over swamps

Jan 1, 1945

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

Executive Committee, Board of Directors Augustus B Kinzel, Chairman, J L Glllson, Vice-Chairman, A W Thornton, Howard C Pyle, Grover J Holt Finance Committee, Board of Directors Andrew Fletcher, Chairman, J S Vanick, Gall F Moulton Investments Gail F Moulton, '60, Chairman, Henry Krumb, '59, J Loveloy, '61, C R Dodson, ex off as Treasurer, Andrew Fletcher, ex off as Chairman, Finance Com¬mittee Endowment Andrew Fletcher, Chairman, N G Alford, H DeWitt Smith, W J Coulter, J V N Dorr, R B Gilmore, J B Haffner, O H Johnson, D H McLaughlin, J R McMillan, L F Reinartz, C E Weed, Wilfred Sykes, J R Suman Honorary Memberships H DeWitt Smith, '59, Chairman, C E Reistle, Jr, '59, Grover J Holt, '59, L F Reinartz, '59, M L Haider, '60, D H McLaughlin, '61, John M Lovejoy, '62, Augustus B Kinzel, ex off as President

Jan 1, 1958

By V. G. Mooradian

THE diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distor-tion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-

Jan 1, 1935

By John A. Gann

THE Iron and Steel Division has shared in the general increased activity of the industry. The fall meeting at Chicago was not only well attended but particularly characterized by the virility and scope of the discussions at the various sessions. The program for the February meeting indicates a similar interest in technological developments. The Blast-Furnace Committee continues to have the hearty support of the industry with discussions of such a nature as to be of real help to the operator as well ass the technologist. The work of the Open-Hearth Committee continues to be outstanding, with ever increasing attendance and ever mounting interest in the meetings. Formation of a conference on the physical chemistry of steelmaking has given those interested in this phase of work an organization allowing the same

Jan 1, 1936

By Norman Pilling

The effects of lead and tin up to maximum contents of about 0.1 per cent. each, in the presence of oxygen between 0.04 and 0.30 per cent., have been studied. Tin is retained efficiently in the oxidized condition, whereas lead is not. An approximate relation between the lead-oxygen and tin-oxygen contents is deduced which, if observed, permits the presence of these elements without detrimental effect. Excess of lead beyond this limit affects ductility and rolling properties adversely and an excess of tin correspondingly diminishes the conductivity. It is shown that copper carrying a combined lead and tin content of several hundredths per cent., yet fully equal in quality to electrolytic wirebar, may be produced under commercial conditions. TIN is not normally found in more than bare traces in current grades of American electrolytic copper, and lead is rarely found to more than a few thousandths per cent. In the electrolytic refining of copper these metals do not present great difficulty in separation and their presence in any considerable amount in copper that has been refined by this method need not be tolerated. On the other hand, the effect of these elements is not entirely academic, as a considerable tonnage of scrap copper liberally contaminated with them has been reclaimed by the fire-refining process into metal with a residual lead and tin content of several hundredths per cent., yet having excellent working properties and fully equal in quality to current grades of electrolytic wirebar. Such copper has been found entirely suitable for use in the manufacture of electrical apparatus. In the absence of oxygen, tin is known to depress the conductivity rapidly, and lead to impair ductility and the rolling properties, yet the effects of these metals on commercial grades of copper-i. e., copper containing from 0.03 to 0.10 per cent. of oxygen-apparently has not received systematic attention. Occasional reference is made to the fact that in the presence of oxygen lead may be tolerated, yet Addicks says,1 in regard to overpoling: "The unstable condition can be controlled by adding certain substances, notably lead, in small quantities, but as mere

Jan 2, 1926

By James E. York

THE honor so fairly earned and so incompletely and tardily paid to Henry Cort, the inventor of the puddling-furnace and the, rolling-mill, has been fully set forth by Mr. Charles H. Morgan,1 and needs no further emphasis here. In view of the importance of the rolling-mill in the treatment of iron and steel, the paucity of information concerning it is surprising. With the exception of a hook, written about 35 years ago, by Peter Bitter von Tunner, an Honorary Member of this Institute, and of desultory articles on simple sections, which have appeared in technical journals, I know of no pub¬lication attempting to treat this subject, although volumes have been written on the scientific theory and technical manipulations involved in other branches of the iron- and steel-industry. This strange anomaly may be due to the fact that roll-turning cannot be called a scientific business. It does not ordinarily come within the range of an educated engineer; yet it cannot be performed by an ordinary mechanic. It demands some of the qualifications of an engineer, in designing, and those of a mechanic, in execution. The men who have followed this trade have controlled the training of their successors. In many cases the technical knowledge required bas been handed down from father to son, and there has been a motive of private interest to prevent its public dissemination. Moreover, the statement of the various principles involved in the process would require, besides manual experience, a degree of scientific knowledge which roll-turners do not usually possess; and, finally, any book on the subject, in order to possess real, practical value, would have to be so fully illustrated as to make it very costly to publish. Regarding my own experience, I may say that I served a six-

May 1, 1906

By Herbert Clark Hoover, Lou Henry Hoover

DIGGING of veins I have written of, and the timbering of shafts, tunnels, drifts, and other excavations, and the art of surveying. I will now speak first of all, of the iron tools with which veins and rocks are broken, then of the buckets into which the lumps of earth, rock, metal, and other excavated materials are thrown, in order that they may be drawn, conveyed, or carried out. Also, I will speak of the water vessels and drains, then of the machines of different kinds,1 and lastly of the maladies of miners. And while all these matters are being described accurately, many methods of work will be explained. There are certain iron tools which the miners designate by names of their own, and besides these, there are wedges, iron blocks, iron plates, hammers, crowbars, pikes, picks, hoes, and shovels. Of those which are especially referred to as " iron tools " there are four varieties, which are different from one another in length or thickness, but not in shape, for the upper end of all of them is broad and square, so that it can be struck by the

Jan 1, 1950

By O. W. Ellis

Before entering upon a general discussion of the fascinating, but at present rather controversial, subject of gases in copper, the author feels that some attention should be directed to the work which has been carried out on the solubility of gases in metals. The outstanding contributions to our knowledge of this subject have been made by Sieverts and his collaborators(1) † and by Iwasé.(2) Both the German and the Japanese investigators employed apparatus of the same general design in their investigations. Full reference need only be made, therefore, to the German scheme, which is diagrammati-cally illustrated in Fig. 1. This, to use the words of Sieverts, which he employed in describing his arrangement of apparatus at the 1928 meeting of der Deutschen Gesellschaft für Metallkunde(10): shows a diagram of the usual mode of procedure. A quartz flask contains the metal (for high temperatures a highly refractory porcelain tube is used) and is connected with the rest of the apparatus by means of a stopcock. The other parts consist of a burette divided into 1/10 c.c., a leveling tube, and an adjustable mercury reservoir. The burette is connected on one side with the gas inlet and on the other side with the absorption flask; the connection can be interrupted by means of suitable taps. Another tap permits the connection of the flask and the Töpler pump. In an experiment the quartz flask is first exhausted and then a measured quantity of gas is let in from the burette. In the first place the volume of the flask when empty is found by calibration with an inert gas. The pressure is read off on the level tube of the burette, and the temperature measured by means of a thermocouple whose welded junction lies close to the outside of the quartz flask, which is heated in an electric furnace. In several experiments the quantity of absorbed gas was transferred to a burette by means of a pump and measured. Care was taken by Sieverts to cool the ground-in joint between the reaction flask (or tube) and the rest of the system. Suitable precautions

Jan 1, 1934

By C. R. Van Hise

Introduction.............29 The Three Zones of the Lithosphere ..30 Zone of fracture............31 Zone of flowage............ 31 Factors influencing depth at which flowage occurs.. 32 Zone of combined fracture and flowage.. 33 The Water-Content and Openings in Rocks....36 Condition of rater in the zone of fracture.. 36 The openings in rocks...........38 Size and number of openings..... 40 Ore-deposits derived from zone of fracture..45 The source of underground water......... . 47 The cause of the flowage of underground water..47 Belts of underground circulation.. 51 Upper belt of underground circulation.. 51 Lower belt of underground circulation.. .... .52 Capacity of water for work in the lower belt of underground circulation........... 53 Movementsof water in the lower belt of underground circulation. 54 The preferential use by water of large channels.. 60 Physico-Chemical Principles Controlling the Work of Under ground Waters..........62 Chemical action............63 Underground aqueous solutions..64 The relations of solution and temperature..... 65 The relations of solution and pressure..66 Precipitation........... 67 Precipitation by change in temperature..68 Precipitation by change in pressure..69 Precipitation by reactions between aqueous solutions.. . 69 Precipitation by reactions between liquid solutions and solids. 70 Precipitation by reactions between gases and solutions. and solids............71 The General Geological work of Underground Waters.. . 71 Division of the zone of fracture into a belt of weathering and a belt of cementation............72

Jan 1, 1901

By V. A. Zanadvoroff

The mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse . sands, representing 60 to 70 percent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. General Considerations The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing- disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. Tailing-disposal Sues The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.—Covers approximately 10 acres. Built up to the height of 60 ft. and abandoned. Total length of dike border is 1900 feet.

Jan 1, 1947

By V. A. Zanadvoroff

The mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse . sands, representing 60 to 70 percent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. General Considerations The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing- disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. Tailing-disposal Sues The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.—Covers approximately 10 acres. Built up to the height of 60 ft. and abandoned. Total length of dike border is 1900 feet.

Jan 1, 1947

Professor Jenney has performed a notable service in presenting this summary of the steadily increasing body of observation on the presence of carbon in rocks of all kinds and its probable influence upon ore-deposition, and in formulating a mode of comparing directly the relative resistance of minerals to oxidation, as well as their reducing-power, and the protective action which minerals having higher reducing-powers exert in preventing the oxidation of associated minerals which possess relatively lower affinities for oxygen. I have had an opportunity of observing a vein which falls within the scope of his interesting discussion. The vein at Ku Shau Tzu, Mongolia, lies directly across a contact of limestone and overlying bituminous shales. Probably it occupies a compression-fissure. The shale has been reduced to such a condition of' non-coherence that much of it can be crushed in the hand, producing a handful of angular fragments resembling beech-nuts in shape and size. In the limestone the metals are principally in argentiferous galena with some pyrite and blende; but the latter two are very subordinate in quantity to the galena. In short, it is an every-day lead-vein in limestone, with siliceous limestone gangue. It is one of those veins in which the ore is not continuous, but consists of a band in the country-rock in which seams of lead sulphide begin at one wall and cross in a bent form, increasing in thickness, to the other wall, where they thin out and end. This may indicate torsional stress, but the shape of the lenses points to some other action. They often ran nearly parallel to the hanging-wall for a considerable distance and crossed the vein on a moderate angle, but turned sharply along the vein on approaching the foot-wall. The intermediate rock contains nodules, bunches and specks of ore, and the lenses vary exceedingly in size, shape and position in the vein.

Jan 1, 1903

By G. W. P. Rengstorff, R. B. Fischer

A study was made of the effect of impurities on the bend ductility of cast molybdenum. High purity molybdenum was repared by re-melting under high vacuum. The ductility of "transverse-grain" specimens indicated that intergranular brittleness decreased with an increase in purity of the metal. THE production of as-cast molybdenum with high ductility at room temperature would make working of the metal easier and increase the usefulness of the as-cast metal. Furthermore, a .knowledge of the factors that influence the ductility of as-cast molybdenum might be applied to the problem of making fusion weldments having satisfactory room-temperature ductility. Individual grains of commercial as-cast molybdenum are slightly ductile at room temperature. However, the presence of carbides at the grain boundaries may cause the metal to fracture in a brittle manner. This behavior has been discussed.' The amount and distribution of the impurities in as-cast molybdenum would be expected, from previous research on the metal, to have considerable influence on its ductility. Some effects of oxygen and carbon on the mechanical behavior of the metal were discussed by Parke and Ham,2 Woodside,3 and Zappfe. Landgraf, and Worden.4 Parke and Ham2 found that, if a sufficient number of molybdenum oxide particles were present at the grain boundaries, the intergranular cohesion was reduced to the extent that arc-melted molybdenum would rupture intergranularly during hot forging. They also found that if the oxygen content was less than 0.003 pct, the cast molybdenum was hot forgeable. It is suspected, however, that forgeable molybdenum may contain a small amount of oxide that could reduce the ductility of the as-cast metal at room temperature. Also, there is the possibility of the unfavorable distribution of other impurities having a detrimental effect on the ductility of cast molybdenum. The results of a study of the influence of purity on the room-temperature ductility of cast molybdenum are presented here. Vacuum Arc-Melting to Produce High Purity Mo One way of determining the effect of impurities on the ductility of molybdenum is to prepare and test metal as free of all impurities as possible. Accordingly, the present investigation was undertaken with this in view. Arc melting in high vacuum (less than 0.1 micron of mercury) was chosen as the method for reducing the impurities below the concentrations occurring in commercial molybdenum. Commercial arc melting of molybdenum is carried out at about 50 microns pressure. During the arc melting, carbon and oxygen in the metal react to form carbon monoxide. By virtue of the vacuum process, the partial pressure of carbon monoxide is maintained at such a low value that the reaction greatly lowers oxygen and carbon contents. An excess of at least 0.03 pct C is used in commercial arc melting to insure that the oxygen content will be below 0.003 pct. The excess carbon remaining after the deoxidation step forms carbides on freezing. Some of the carbides precipitate at the grain boundaries and, as will be shown, have an unfavorable effect on the room-temperature ductility. In the present work, only the small amount of carbon (0.003 pct) contained in the commercial powder-metallurgy molybdenum used for melting stock was present. Partial removal of oxygen from the melt probably occurred as the result of the volatilization of molybdenum oxides, or by distillation of oxygen at the high melting tem-

Jan 1, 1953

By Henry Rawdon

THE RELATION between the course, or path, of the fracture of metals and alloys, produced in service or as a result of certain laboratory tests, and the crystalline units of which such materials are composed is of utmost importance. The fracture of normal material is, in general, intracrystalline, i.e., it consists of a break across the grains rather than of a separation between them. An intercrystalline fracture indicates either that the metal is of very inferior quality or that the break occurred under very unusual conditions, e.g., at a very high temperature. The usual mechanical tests, when applied to metals of the type that breaks with an intercrystalline fracture, merely measure the coherence of adjacent grains for one another and reveal little as to the real properties of the metal itself. Even such a soft plastic substance as lead, under suitable conditions, may be rendered so weak and brittle that the metal can be easily crumbled into powder by the fingers although the constituent grains have lost none of the intrinsic properties of lead. Various erroneous explanations of this behavior of lead have appeared in the scientific literature, the change being described usually as an allotropic one. The importance, in an industrial sense, of a proper explanation of this type of the corrosion of lead justifies the description of the type of metal deterioration that follows.

Jan 2, 1920

By Robert McKay

THE practical study of corrosion requires consideration off its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as. a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing." This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique.

Jan 1, 1929

By Thomas V. Falkie, Robert Stefanko

Recently The Wall Street Journal featured a series of articles titled "The Dirty Work-Brutal, Mindless Labor Remains a Daily Reality for Millions in The US.-Mining Coal, Shoveling Slag, Gutting Hogs Pays Bills But Can Drain Spirit, Hope." The article was devoted to describing how tough and dangerous is mining (and some other jobs) and how rough life is for miners and their families. Similarly during the past few years some psychiatrists and sociologists have devoted increased attention to the attitudes and life styles of miners. Unfortunately most of their approaches have been neither scientific nor objective, and very little good clinical research has been done on the subject.

Jan 1, 1971

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

By A. P., Svenningsen

ECONOMICAL handling of a minimum of 25,000 tons of minus 3/4-in. ore per day, grinding it to 2 per cent on 65 mesh, and effecting a high recovery of the copper at the lowest possible cost were the principal aims in the design of the new Morenci concentrating plant. Dealing with a tonnage of this magnitude, it is obvious that lost motion cannot be tolerated. When ore is carried on a conveyor an unnecessarily long distance or elevated to a greater height than necessary, or when pulp flows in a launder by a circuitous route thereby losing elevation and distance, we have lost motion which is always costly both from the standpoint of construction and operation. In addition to the 25,000 tons of ore which must be handled, 100,000 tons of water per day has to be carried through the plant in the treatment of the ore. Though water is not so difficult to handle as the ore, the combined tonnage represents a figure which could easily run into a considerable monetary loss per day if all phases of the design were not carefully followed with the idea of eliminating any unnessary handing of materials.

Jan 1, 1942