Search Documents

By H. Cecil Spicer

The results described in this article are based on field work conducted during the periods APril-May, 1939, and MaY-JulY, 1940. The United States Potash CO. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation mas completed under a cooperative arrangemerit made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an l was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the disrovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlum-berger5 in a communication. Messrs. Alty6 described studies 0" salt deposits in which the sing[e-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performetl with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,ll through the courtesy of Harry Aurand, of the Midwest Refining CO.

Jan 1, 1942

By D. D. Pollock, D. I. Finch

PREVIOUS work' on a four-component system (Cu-Mn-Ni-Fe) resulted in the development of consistent relationships between the chemical composition and the electrical properties of these manganin-type alloys. The present study was undertaken to develop alloys with temperature coefficients of resistivity and thermoelectric properties more desirable than those of the manganin type, and to determine whether the relationships which had been found for the Cu-Mn-Ni-Fe alloys could be extended to five-and six-component alloy systems. PREPARATION OF ALLOYS The five- and six-component alloys were made from OFHC copper rod, ARMCO iron, electrolytic nickel, manganese cathode chip, and special high-purity aluminum and indium. A Cu-Mg master was used for deoxidation. The compositions of these materials are given in Table I. The alloys were melted and cast as indicated previously,' except that no cover was used and the melts were teemed. EXPERIMENTAL PROCEDURE The finished wire size of 0.0808 in. diam was again selected for the reason that the test specimens would be self-supporting, thus eliminating any extraneous effects which might have been introduced by winding smaller diameter wire on spools or forms. The following tests were performed on the finished wires: A) Chemical Analyses—All of the components of these alloys were determined by premium gravimetric methods. The principle residual impurity contained in these alloys is 0.008 pct Mg (by weight), maximum. Tables II and 111 present the mean analyses computed from at least four determinations of each constituent. B) Electrical Characteristics—The test procedures forthe determination of the thermal emf vs copper, resistivity, and the resistance-temperature relationship are given in detail in Ref. 1. It was also shown that the resistance-temperature relationship is of the form Pt = P,n + At -B/2, [1] where P, is the resistance at t C expressed in percent of a given standard resistance, P, is this per- 0 centage at 0°C, and A and B are constants for a given, properly treated, composition. The results of the electrical tests are also given in Tables II and 111. INTERPRETATION OF DATA The modified Linde2 formula, known to be valid for dilute binary solid solutions, was applied to the complex Cu-Mn-Ni-Fe type alloys. This relationship is of the form where Ap is the increase in resistivity. Zb the valence of the solute, Zn the valence of the solvent, and K and K are designations assigned by Robinson and Dorn3 to the constants for the periodic group to which solute element belongs. The units of K, are -cm per valence difference squared per at. pct; those of K2 are pa-cm per at. pct. For the sake of brevity, these units are not repeated in the following discussion. Calculations were made to determine if this formula was accurate for five-component systems. No experimental studies were made of the Cu-In and Cu-A1 binary systems. The effects of indium additions upon the resistivity of copper are given by Linde. These data, along with those of the effects of Mn and Fe, permitted the calculation of the effects of Al.

Jan 1, 1959

By Dr. O’Neil Thomas J., Donald W. Gentry

The greatest of all gifts is the power to estimate things at their true worth. LaRockefoucauld INTRODUCTION The primary reason for performing a feasibility study on a proposed mining venture is to investigate all phases of the proposal in as much detail as necessary to justify either dropping the project or continuing expenditures through the next stage. The economic evaluation component of the feasibility study, therefore, must ultimately be based on information which provides an answer to the question, "What is it going to cost?" Unfortunately engineers preparing feasibility studies never have all the engineering or economic information they would like or need. Consequently, the economic portion of the analysis can only be performed if estimates of the various costs associated with the project are made. Project cost estimates, in turn, require estimates of all the physical factors affecting cost components, including anticipated performance of plant and equipment as well as all pertinent geologic, mineralogic, and metallurgical variables. Before useful cost estimating procedures can be applied considerable data must be collected, compiled, and organized. Preparatory work typically includes organization of cost data available for estimating purposes, development of techniques for updating historical costs, and establishing methods of forecasting prices and costs over the duration of the project. Cost estimates for mining and mineral processing projects involve so many features and variables that it is absolutely essential to have some means by which the vast amount of detail can be organized. It is very important to identify, in as much detail as possible, all the cost data available (historical and developed) to the estimator. These costs, after being properly identified in detail, should be com- piled, stored, updated regularly, and made readily available for use in developing new cost estimates Accessing files of current cost information requires a standardized numerical system of classifying cost data. When uniform definitions and procedures are used, every project record contributes to the common store of estimating data.

Jan 1, 1984

By H. J. McQueen, G. C. Kuczynski

ThE useful properties of k6-Alfenol and the thermenol alloys (summarized by J. E. Nachman and W. J. Buehler') have encouraged research into those alloys which, having compositions near 25 at. pct Al, 75 at. pct Fe, undergo an ordering transformation between 500° and 550°C. The equilibrium diagram of the iron-rich iron-aluminum alloys was first determined by Bradley and Jay.2,3 They distinguished three structures: the disordered, which is bcc; FeAl, which is simple cubic with one Fe atom and one Al atom per lattice site; and Fe3Al, which is fcc with three Fe atoms and one Al atom per lattice site. This last structure may be conceived as eight body-centered cubes with Al atoms at the centers of alternate ones, so that Al atoms have only Fe as first and second nearest neighbors. Later, Osawa and Murata4 determined the boundaries of the different superlattice regions in the iron-rich Fe-Al solid solution by dilatometric and X-ray methods. Two of the six phases, which they found between 0 and 50 at. pct Al, were never identified by other workers. A. Taylor and R. M. ones,' concurrently with and independently of this research, redetermined this diagram by measuring lattice parameters at temperature. Further reference will be made to their results. EQUILIBRIUM DIAGRAM A) Experimental Procedure—The alloys were prepared from NRC gas-free iron (99.9 pct Fe) and 99.99 pct Al. They were melted in alumina' crucubles under vacuum in an induction furnace. If the ingots were unsound or showed more than a 3 pct weight loss, they were rejected. The ingots were homogenized at 1100°C for 24 hr before hot-rolling at 700" to 900°C from 1 in. to 0.25 in. thick. It is interesting to note that alloys containing more than 28 at. pct Al were able to take an 80 pct reduction of area in the ordered FeAl region. The dilatometer specimens and specimens for chemical analysis were cut from these plates. A Leitz dilatometer was used to measure the coefficient of linear expansion as a function of temperature. The specimens were slowly cooled from 900" to 300°C where they were annealed for 10 hr before slowly cooling to room temperature. The expansion was recorded photographically as the alloys were heated and cooled at 1.5oC per min between 100" and 1000°C. The magnetic measurements determining the Curie points were performed on the dilatometer specimens in the dilatometer, by using direct current in the furnace windings both to heat the specimen at 1.5°C per min and to serve as the primary coil. The regular specimen holder was replaced by a thin alundum tube on which was wound, as a secondary, a closely spaced coil of fine copper wire. A reversal of current in the furnace windings produced, in the secondary, an emf which was proportional to the induction in the specimen, and which could be detected on a galvanometer. In this way, it was possible to determine the Curie points of alloys to within * 5°C. B) Results and Discussion—The coefficients of linear expansion, as obtained from the dilatometer curves, are plotted as a function of temperature and composition in Fig. 1. Since in many cases the heating and cooling curves were superimposed, it was decided to measure slopes of heating curves only. Definite high peaks, due to the transformations, were observed on each curve between 400" and 520°C, and, for alloys containing more than 23 at. pct Al, a second set of smaller peaks at temperatures above 660°C. The sharpness of the peaks indicates that ordering to Fe3Al is a first-order reaction. The compositions and the temperatures of these peaks are listed in Table I. When these temperatures are plotted as a function of the composition, the result is the constitution diagram presented in

Jan 1, 1960

By David White

THE submission of carefully prepared estimates of the oil reserves of the United States calls for no apology or explanation. In this country, petroleum is a rapidly wasting asset and an occasional appraisal of the amount remaining in the ground is a simple business procedure to safe-guard the general welfare and the prosperity of the republic. The rumored danger of failure, in the near future, of the foreign supply on which we depend in constantly increasing amounts makes the immediate review of our available reserves the more imperative. The Director of the U. S. Geological Survey, in March, 1921, requested the American Association of Petroleum Geologists to cooperate in the preparation of new estimates of the oil remaining in the ground. With the members of this cooperative committee, state geologists, regional geologists, consulting specialists, and geologists and engineers attached to many companies worked both independently and through sub-committees. The reports for districts, counties, fields, etc., after review by local or state committees, were discussed by the joint cooperative committee in conferences that, in some instances, were attended by the original compilers of estimates for the states or smaller areas. Finally the data were reviewed and the figures revised by the joint cooperative committee, so that the totals given in Table 1 represent the opinion of the committee, which was composed of F. W. DeWolf, W. E. Wrather, Roswell H. Johnson, Wallace A. Pratt, Alexander W. McCoy, Carl H. Beal, C. T. Lupton, G. C. Matson, K. C. Heald, W. T. Thom, Jr., A. E. Fath, Kirtley F. Mather, R. C. Moore, and David White, chairman.

Jan 6, 1922

By R. S. Knappen, D. V. Carter

In the states east of the Mississippi River, oil field operations were generally restricted during 1927. Active drilling was chiefly confined to the flood district of Bradford, and to the new areas in western Kentucky, Michigan, and southwestern Indiana. In spite of the general depression, production increased in every state, except Illinois. This unexpected increase is. due to several factors. First, in 1926 there was little flush production outside of Illinois, and the decline 'curves in all states are exceedingly flat. Second, the floods in Bradford, Pennsylvania, and Allegany County, New York, proceeded normally and increased production in those states for the fourth consecutive year. Third, new pools in Kentucky, Indiana and Michigan gave important flush production. Fourth, the general unsatisfactory market forced the operators to scrutinize carefully all their operations and improve efficiency and production in all possible ways. Increases amounted to approximately 2,000,000 bbl. Illinois lost, 900,000 bbl., leaving a net gain for the states east of the Mississippi River amounting to 1,100,000 bbl., or a total 40,268,000 barrels. Pennsylvania and New York In northern Pennsylvania and southern New York, the principal activity centered in the districts where flooding is being used to increase the recovery from the old districts. Once started, the flood cannot be shut off. The producer must drill wells and take his oil on schedule, or irrevocably lose it. Accordingly, in face of an adverse market Bradford and Bolivar operations increased 24 per cent. This area furnished more than 40 per cent. of the oil wells completed east of the Mississippi River last year, although the average initial production was less than 2.5 bbl. Unlike all normal fields, this production increases for several months until water appears in the well. For this reason, these wells will produce much more oil than would appear probable from the statement of initial production. During the year, air or gas pressure was applied to several new properties. Surplus gas is rarely available and air has been more commonly used. Two explosions occurred as a result of recycling air-gas

Jan 1, 1928

The following is an incomplete list of members and guests who called at Institute headquarters during the period Nov. 10, 1918 to Dec. 10, 1918. Arthur C. Adair, Camp Meade, Md. L. S. Mitchell, Montreal, Canada. Arthur K. Adams, Camp Humphreys, Va. T. E. Mitchell, San Francisco, Cal. Toner Antisell, Chevy Chase, Md. H. Mortimer-Lamb, Montreal, Canada. V. W. Aubel, New Castle, Pa. Edmund Newton, A. C. Black, El Paso, Tex. Paul T. Norton, Jr., Columbus Ohio. 0. F. Brinton, Baxter Spgs., Kans. Elmer W. Pehrson, San José, Cal. C. S. Corbett, Minneapolis, Minn. Joseph E. Pogue, Washington, D. C. W. M. Corse, Mansfield, Ohio. T. C. Roberts, E. Orange, N. J. G. C. Crossley, Toms River, N. J. D. R. Semmes, Richmond, Va. H. S. Emlaw, Grand Haven, Mich. H. L. Slosson, Jr., San Francisco, Cal. Rudolph Emmel, Boston, Mass. W. H. Staver, S. G. Garrett, U. S. N. R. F. A. L. Sweetser, Boston, Mass. Lt. Francis Geib, Denver, Colo. Lt. H. B. Taylor, Kansas City, Mo. Wm. E. Hubbard, Wichita Falls, Tex. Kirby Thomas, New York. Arthur Iddings, Wichita Falls, Tex. Benj. F. Tibby, Salt Lake City, U. Zay Jeffries, Cleveland, Ohio. J. L. Towne, Whitepine, Colo. S. J. Kidder, Mogollon, N. M. Chas. W. Tubby, St. Paul, Minn. Lt.-Col. W. H. Lanagan (Engrs.). A. G. Waite, Brookline, Mass. Major W. F. Lewis (Engrs.). Timothy D. Walsh, Denver, Colo. 0. M. Lewyn, Thomas Warner, Phoenix, Ariz. A. McClintock, DeKalb June., N. Y. J. P. B. Webster, London, England. Major Donald G. Miller, N. M. E. W. Westervelt, Los Angeles, Cal. C. E. LeN. Arnold, formerly with the Inspiration Cons. Copper Co. at Inspiration, Ariz., has accepted a position with the Consolidated Arizona Smelting Co. at Mayer, Ariz.

Jan 1, 1919

By J. F. Myers, F. M. Lewis

C. G. McLACHLAN*-I have read this paper with considerable interest and wish to congratulate the authors on the care with which they carried out their experiments and for the detailed sizing data they have presented. 011 the other hand I do not feel that these data establish their contention that "with other factors the same, the work accomplished in a fine crushing rod mill is directly proportional to the rotating speed." My reason for making this statement is that their conclusion is based on the percentage of minus 65 mesh material produced at each of the speeds at which their tests were run. The rod mill is, however, not a fine grinding machine and therefore figures based on minus 65 mesh production are figures outside the range at which it operates to best advantage. Further, if rod mill performance is to be judged on the production of such material it should have been established that a rod mill will produce it as effectively as a ball mill. To check this last point I have gone over some of the rod and ball mill grind-ing figures for our Waite-Atnulet operation and find that the ball mill at that property produces more minus 65 mesh material per horsepower than the rod mill. Moreover, this comparison is even more favorable to the ball mill if it is limited to minus 100 mesh production. It therefore seems to me that the most satisfactory basis on which to try to com-pare the performance of the rod mill in the present case is by taking a weighted average of all the new surface produced per horsepower. W. H. Coghill3 has published data which can be applied to the sizing figures presented by the authors, and if this is done the units of new surface per horsepower produced in the Tennessee tests are as follows: Admittedly the increment of increase in new surface per horsepower shown in the foregoing figures is not great, but its trend is nevertheless definitely in favor of slower speed operation, for the conditions under which these particular tests were run. I also feel that some information regarding liner contour should have been given as I think it will be found that a mill which is equipped with liners which lift the rod load can be run at a slower speed than a mill in which the liners are comparatively smooth. J. F. MYERS and F. M. LEWIS (authors' reply)—The position taken by Mr. McLachlan is to be respected even though we are all aware of the faults of surface considerations. As he points out. the increment of increase is very small. It is so small in fact that for all practical purposes it does not conflict with the conclusions of the paper. The authors appreciate Mr. McLachlan's comprehensive study of the data.

Jan 1, 1950

The mountains of Utah contain one of the largest deposits of high grade bituminous coal in the world. According to the United States Geological Survey, there are 13,130 square miles of land known to contain workable coal, and these extensive fields contain 196,000,000,000 tons of coal. More remarkable than the extent of the coal fields is the thickness of the coal beds. Over three-fourths of the output of coal in Utah is recovered from beds ranging from 8 to 17 feet in thickness, as com- pared to one-eighth of the output of the entire country from such beds. In 1917, Utah mined one-third of its coal from seams at least 16 feet thick, compared to one-half of one per cent of the total bituminous output of the country from like seams. Coal at Wales, in Sanpete county, and in the vicinity of Coalville, Utah, was, it is reported, the first discovered by white men in the state. Wales claims the distinction of having produced the first coal mined in Utah. Two men, who had been coal miners in Wales, learned of the coal from an old Indian chief who called it "rock that would burn." In 1857, the town of Wales was founded and coal mined, and in 1858 some coke was manufactured and hauled by ox team to Salt Lake City. South of Wales is Castle Valley, in Wasatch Plateau field. From 50 to 60 miles of the old Spanish Trail from Santa Fe. New Mexico, to Monterey, California, lies in Castle Valley. The coal in this field may or may not have been known at the time the trail was used extensively. The first published reference to this coal, however, was made by a party of the Corps of Topographic Engineers in their journal for October 11, 1853.

Jan 1, 1925

By Allen Garrison

A PREVIOUS paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their com-position, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions, Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. EXPERIMENTAL PROCEDURE The difficulties involved in the measurements of the flow character-istics of plastic fluids are too familiar to recite, The possible applications of some of the well-known instruments to this problem have been ade-quately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measure-ment of clay or shale suspensions, Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first require-ment is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1939

By A. H. Tousley, C. L. Vickers

The author presents a history of the development of the Port of Long Beach from its beginning in 1905 to the present construction of a new bulk loading facility. In describing this new facility, emphasis is placed on such aspects as rail car and truck handling, gravity yard, rotary car dumping, bottom dumping, car dumping equipment, feeding and conveying, ship-loader-stockpiler, stockpiling and reclaim, dust control, and construction problems. Development of the Port of Long Beach, Calif. (see Fig. I), began in 1905. In that year private Long Beach interests acquired 800 acres of marshland in the Inner Harbor area and initiated a program of channel dredging and land reclamation. Efforts to establish a municipal port began a short time later and culminated in the opening of Pier 1 in 1911. An event of even greater significance to the port future also occurred in 1911. This was the tideland grant enactment by the state legislature that conveyed to the city of Long Beach all of the state's rights in the tidelands located within the city boundaries. The grant stipulated that all revenue produced from the tidelands be used for the development of navigation, commerce, and fisheries. During the next 15 years up to 1926, the port's commercial growth was steady, although relatively slow. During this period, several fundamental steps in the development of a major harbor were accomplished. These included the creation of the Board of Harbor Commissioners in 1917, the dredging of the Inner Harbor and entrance channel to accommodate deep draft vessels, and the correction of a serious silting problem through construction of the Los Angeles River Flood Control Channel. These efforts bore fruit during the ensuing 10 years in the establishment of more than $30,000,000 worth of industrial plants and private marine terminals in the Inner Harbor. Commerce over municipal wharves also increased more rapidly, and it became necessary to start the development of the harbor in a seaward direction. In 1936, oil was discovered in the harbor area, and the first Harbor Dept. well was brought in 2 years later. It soon became evident that the city of Long Beach would receive substantial revenue that, under the terms of the state grant of 1911, must be used in the development of the port. It was further realized that to properly guide and coordinate such development, a long range comprehensive plan was essential. The Board of Harbor Commissions contracted with G. F. Nicholson and J. F. Collins, consulting engineers, for the preparation of such a report that was completed in 1940. The Nicholson-Collins report proposed the development of an East Basin, between the entrance channel and the Los Angeles River, and a West Basin in the area now occupied by the Long Beach Naval Shipyard. Twenty full-size berths were to be provided in the East Basin and more than fifty berths in the West Basin. The report recommended extensive modern terminal facilities for handling waterborne cargo. Attention was given to improvement of the street and highway system to give better vehicular access and to avoid congestion within the port. To a large extent the recommendations of the Nicholson-Collins report were followed in the subsequent development of the East Basin. This development was greatly accelerated by World War 11, with its need for increased oil production and additional shipping facilities. The wartime and immediate postwar construction was largely concentrated on Pier A, with the development of Piers B, C and D following in more recent years. An important factor in the planning of these piers was their dual function as oil drilling sites and cargo piers. The Navy's acquisition of the West Basin area made it necessary to depart from the Nicholson-Collins plan and find other areas for future expansion. At the present time only one Inner Harbor Port-owned area having protected deep water frontage remains undeveloped. This is the property fronting on Channel 2 in the Inner Harbor acquired in December 1957, from Pacific Dock and Terminal Co. The growth of the port has been in a southerly direction since the construction of the Long Beach Naval Shipyard in the West Basin area. Recent extension of Piers F, G and J into the ocean follows typical port construction methods developed during the expansion of the Middle Harbor during the last 20 years.

Jan 1, 1963

By A. Chakravarti, C. C. Harris

First-order kinetics adequately describe the recovery of a single floatable species. The conditions under which cell behazior can be simulated by a single-phase model are discussed; deviations from the multiphase model are accountable. The rate coefficient depends upon operating conditions besides particle size and mineralogy and the physicochemical properties of the pulp constituents. The model for a real flotation system combines the first -order, single-phase model with a distribution of noninteracting species. Methods for determining the distributions are discussed. Applications of the procedure to flotation studies are outlined. The mathematical description of flotation as a rate process can be traced to Garcia1 who reported cases in which the fraction of solid remaining in a cell in semi-batch operation, F (for Notation used throughout, see Table l), decays exponentially with experimental time T. F = e-k>r. (1 The differential equation leading to Eq. 1 is dF ----= -k,F (2) dT which is recognized as the algebraic analog of the chemical kinetics first-order reaction equation.' This has led to suggested mechanisms for flotation and mathematical relationships other than first order: with very little foundation other than analogy. The flotation rate coefficient kl can be accounted for as the product of several probabilities concerning bub-ble-particle attachment and detachment, aggregate entry from pulp into froth and return from froth to pulp, and removal from froth as concentrate. These factors clearly contribute to the magnitude of the overall flotation rate, and there are others also, but describing flotation merely as the overall probability of consecutive gross events hardly appears a significant advance in understanding. More recently, it has been described in terms of a stochastic process, which promises to provide a more satisfactory approach? The present paper will be more concerned with a phenomeno-logical description of the flotation process than with an account of the internal mechanics of the process. This is not a statement of priorities, or a judgement of the relative importance of these options but rather an assessment of what is presently possible. Previous investigators'" have developed methods for interpreting semi-batch flotation data in terms of species distribution. These methods have been used in an attempt to explain flotation behavior in response to changes in operating conditions." Inspection of examples given in the literature" reveals discrepancies between theory and experiment, and data obtained in the Colum-

Jan 1, 1971

By A. K. Bhasin

A. K. Bhasin, (Development Engineer, Marcona Corp., San Francisco, Calif)-The author suggests the use of the term "consistency" for apparent viscosity and accordingly calls his viscometer a "consistometer." However, he goes on to refer to "consistency" as a combination of plastic viscosity, yield stress, and stability (p. 104, col. 2, line 6). Unfortunately, such conflicting terminology is encountered too often in rheological

Jan 1, 1973

The following list of US companies, mines, and mills engaged in uranium production was compiled by the Health and Safety Analysis Center, Mine Safety and Health Administration, in Denver, Colo. The list includes those companies reporting to the Center in 1978. Thanks to D. K. Walker, Chief of the Health and Safety Analysis Center, for providing the information to MINING ENGINEERING.

Jan 10, 1978

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936

By Robert J. Hite, Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table 1), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term potash originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first US patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 27.5 Mt K20 produced in the world in 1980 (Searls, 1981) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K20, a unit of measure which is neither a natural nor synthetic compound of potassium (1.0% K is equivalent to 1.2046% K2O). Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and metamorphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such deposits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of seawater or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in Table 1. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971). The structural basins within which marine evaporites occur are of two main types: (a) cratonic basins formed by broad epirogenic movements (for example, the Michigan Basin of the midwestern United States and the Permian Zechstein Basin of eastern Europe), and (b) grabens, commonly related to continental

Jan 1, 1983

By R. T. Hukki, A. M. Gaudin

Previous work on the principles of comminution has shown: (I) that the surface produced is proportional to work input (Rittinger law,1a-3); (2) that there is regularity to the weight distribution of the fragments according to size.4-10 In this paper it is brought out that the surface on the fragments is distributed in definite and simple relation to size. The experimental work has involved: I. Construction of an apparatus capable of measuring the surface of mineral fragments independently of the chemical composition of the fragments and independently of the site of the surface; 2. Refining the methods available for measurement of particle size; 3. Designing and building a crusher capable of operating on very small quantities of mineral, if necessary on single crystals, and in such fashion as to minimize handling losses of material. Complete experiments have been carried out with massive quartz and individual quartz crystals. partial experiments, lacking surface measurements, have been made with glass spheres, galena, sphalerite, fluo-rite, salt and coal. Introduction The existence of regularity in weight distribution with size was noted many years ago, especially by A. 0. Gates;' the subject was also studied in detail by one of us.6 In the latter paper it was shown that rocks can be divided into two classes: homogeneous rocks, which show no preferential breaking, and heterogeneous rocks, which show preferential breaking at the grain size of the rock. It was shown, furthermore, that the fragments obtained by rupturing a homogeneous rock occur (in the fine range) in such abundance as to permit the writing of a relatively simple equation to relate the weight retained on a screen to the screen opening. With screens of which the openings are in constant ratio, the weight retained, w, is related to the screen size x by the equation w = Cxm [I] In this equation C and m are experimental constants. A plot of weight retained against particle size is a straight line of slope m if the scales for x and w are both logarithmic. In the fine range, the slopes of the size-distribution graphs plotted according to the method described above vary within a limited range. An inspection of a number of size-distribution data by various experimenters indicates that the slope very seldom exceeds 1.0, but is usually greater than 0.7. More recently, schuhmann8 proposed a method of charting that has so many advantages of its own that it has been used primarily in this work. For fine particles Schuhmann has found that the data are represented by the equation (x)m k [2]

Jan 1, 1947

By A. M. Gaudin, R. T. Hukki

Previous work on the principles of comminution has shown: (I) that the surface produced is proportional to work input (Rittinger law,1a-3); (2) that there is regularity to the weight distribution of the fragments according to size.4-10 In this paper it is brought out that the surface on the fragments is distributed in definite and simple relation to size. The experimental work has involved: I. Construction of an apparatus capable of measuring the surface of mineral fragments independently of the chemical composition of the fragments and independently of the site of the surface; 2. Refining the methods available for measurement of particle size; 3. Designing and building a crusher capable of operating on very small quantities of mineral, if necessary on single crystals, and in such fashion as to minimize handling losses of material. Complete experiments have been carried out with massive quartz and individual quartz crystals. partial experiments, lacking surface measurements, have been made with glass spheres, galena, sphalerite, fluo-rite, salt and coal. Introduction The existence of regularity in weight distribution with size was noted many years ago, especially by A. 0. Gates;' the subject was also studied in detail by one of us.6 In the latter paper it was shown that rocks can be divided into two classes: homogeneous rocks, which show no preferential breaking, and heterogeneous rocks, which show preferential breaking at the grain size of the rock. It was shown, furthermore, that the fragments obtained by rupturing a homogeneous rock occur (in the fine range) in such abundance as to permit the writing of a relatively simple equation to relate the weight retained on a screen to the screen opening. With screens of which the openings are in constant ratio, the weight retained, w, is related to the screen size x by the equation w = Cxm [I] In this equation C and m are experimental constants. A plot of weight retained against particle size is a straight line of slope m if the scales for x and w are both logarithmic. In the fine range, the slopes of the size-distribution graphs plotted according to the method described above vary within a limited range. An inspection of a number of size-distribution data by various experimenters indicates that the slope very seldom exceeds 1.0, but is usually greater than 0.7. More recently, schuhmann8 proposed a method of charting that has so many advantages of its own that it has been used primarily in this work. For fine particles Schuhmann has found that the data are represented by the equation (x)m k [2]

Jan 1, 1947

By V. H. Gottschalk

SEVERAL years ago a group in the metallurgical division of the U. S. Bureau of Mines began a study of the application of new developments in physics to metallurgical problems'. Among these developments were the extensions of what may be termed by analogy the "sound spectrum." Electromagnetic waves, from X-rays to radio waves, have been quite thoroughly explored for metallurgical use, but the sound spectrum, extending from low-frequency vibrations involved in certain types of metal failure by fatigue through the range of audible sound to inaudible vibrations having frequencies of many kilocycles, has had only meager consideration from metallurgists. Because of the general interest in the process recently demonstrated by St. Clair3 for flocculating smoke by means of sound waves, this article is written to point out possible applications of sound and supersonic (ultrasonic) waves in the metallurgical industry.

Jan 1, 1937

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y', and E carbonitride has been confirmed and it has been found that y' is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part' reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,' this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* 'Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970