Search Documents

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By L. H. JEFFRIES

In the mining operations of The Canyon Corp., Deadwood. S. D., the use of mucking machines has been of definite advantage. The type used is that which depends upon the traction of the motor-driven wheels to crowd the dipper into the muck pile, while the car in which the muck is received is coupled to the mucker and moves forward or back with it. This general arrangement is entirely satisfactory on a substantially level track. The ores which occur in this district are a replacement of dolomite and the beds are now tilted to an inclination of about 7-1/20. In our operations it is necessary to drive inclines down-hill on this slope, which makes a difficult hand-mucking job even if water were not present. With these facts in mind, an attempt was made to use the mucking machine for driving down the in- cline, but as expected, the traction was insufficient to handle the machine and the necessary car. The means used to correct this condition will perhaps impress most readers as too complicated and cumbersome to effect any economy, but the idea may be of service to some who have a similar condition. After considering several s

Jan 1, 1940

By G. Horvay, J. G. Henzel

Nomograms and charts are provided which permit rapid determination of the mold-casting interFace temperature and the speed of solidification when a semiinfinite ingot is cast into a semiinfinite mold. The physical properties of the mold, the frozen metal, and the liquid metal are not assumed to be equal, but they are assumed to be temperature independent. The results are correlated with charts prepared by Paschkis and Hlinka—using Columbia University's Analog Computer—for the freezing of finite ingot slabs when a constant surface temperature is impressed, and with experimental cooling curves obtained by Pellini in sand and iron molds for 7 in.-sq steel castings. x = coordinate directed to right of zero (freezing direction) y = coordinate directed to left of zero (melting direction) e = position of freezing front (in x direction) ? = position of melting front (in y direction) $ = temperature (function of position and time) ? = fixed temperature 2L = width of finite slab Y = a fixed position in the semiinfinite mold, or the width of a finite mold (see Section 7) Properties y = density, lb per cu ft c = specific heat, Btu per lb deg F k = conductivity, Btu per ft hr deg F X = heat of fusion, Btu per lb k = k/Yc = temperature diffusivity, sq ft per hr* b - = = - heat diffusivity, Btu per sq ft deg F Vhr Subscripts 2 = pertaining to the still-liquid metal (case of freezing), or the medium which furnishes the heat (case of melting) 1 = pertaining to solidified metal (case of freezing), or to molten metal (case of melting)* 0 = pertaining to mold (case of freezing), or to the still-solid metal (case of melting) f = pertaining to fusion condition (eg.,?f - fusion temperature) i = pertaining to the location x = 0 (the mold-ingot "interface")

Jan 1, 1960

By Morris Cohen

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. O. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publicotions Committes: Extractive Metallurgy Division: R. E. Lund, Chairman; M. E. Wadsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iran and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, D. W. Murphy, Johannes M. Uys, J. B. Wogstoff, and R. G. Ward. Institute of Metals Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. 0. Brittain, J. B. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurland, H. S. Kalish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swalin. Published bimonthly by the Americon Institute of Mining, Metallurgicol, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaza 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Centrol America; $32, foreign; $30per$7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any stotement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 4.

Jan 1, 1962

By G. V. Kurdjumou

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J. S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Choirmon; M. E. Wodsworth, Vice Choirmon; D. H. Boker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Chorles O'Neill, A. W. Schlechten, R. E. Shinko~ke~, and W. W. Stephens. Iron and Steel Division: T, V. Wainright, Choir- mon; ti. L. Bishop, R. E. Boni, T. E. Doncy, D. W. Murphy, Johonnes M. Uys, J. B. Wogstaff, ond R. G. Word. Institute of Metals Division: J. N. Hobstetter, Choirmon; P. A. Beck, J. J. Beckar, G. F. Boiling, J. O. Brittain, J. 0. Clark, R. 5. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurlond, H. S. Kolish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richrnon, H. C. Rogers, W. Rostoker, O. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, ond R. Swolin. PuUlished bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaZa 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Central America; $32, foreign; $30peryear$7.50 for AIME members. Single copies, $6.00, single copies foreign, $6.50. The CentralAmerica;AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . .Copyright.Registered cable address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical cableaddres .. . AlME class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 3.

Jan 1, 1962

By E. T. Turkdogan, P. Grieveson

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie lnstitute of Technology Sc hen ley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. '4. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Chatrmon; M. E. Wodsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Groce, W. A. Krivsky, R. A. Lewls, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, C. W. Murphy, Johonnes M. Uys, J. B. Wagstaff, and R. G. Ward. lnstitute of Metols Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. O. Brittain, J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifalco, J. C. Gurland, H. S. Kclish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swolin. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American lnstitute of Mining, Metollurgical. and Petroleum Engineers. Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustriol Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 6.

Jan 1, 1962

By M. O. Abo-el Fotoh, J. B. Mitchell, J. E. Dorn

The effect of strain rate and temperature on the tensile flow stress of a polycrystalline bcc alloy of magnesium containing 14 wt pct Li and 1.5 wt pct Al was investigated for strain rates of 3.13 x lom5 to 3.13 x 10-3 per sec over the range from 20° to 300°K. From about 180° to 300°K the alloy exhibited an ather-ma1 deformation behavior where the flow stress was independent of strain rate and increased only slightly with decreasing temperature. At lower temperatures the flow stress was strongly strain-rate- and temperature-dependent, characteristic of deformations controlled by thermally activated mechmzisms. The activation volume for thermally activated plastic defornzation was between 5 and 30 cu Burgers vectors, independent of plastic strain. This low-temperature thermally activated deformation behavior was found lo be in satisfactory agreement with the theoretical dictates of the Dorn-Rajnak1 formulation of the Peierls mechanism where deformation is controlled by the rate of nucleation of pairs of dislocation kinks over the Peierls energy barriers. SEVERAL studies of the low-temperature thermally activated deformation of bcc metals and alloys (molybdenum,1 tantalum,1 Fe-2 pct Mn,2 Fe-11 pct MO,3 and AgMg4) have revealed that the strain rate is controlled by the activation of dislocations over the Peierls-Nabarro energy hills. Although there is some uncertainty as to the nature and effect of solute atom-dislocation interactions during low-temperature deformation of bcc metals, it has been concluded by Dorn and Rajnak,1 Conrad,1 and Christian and Masters6 among others that overcoming the Peierls-Nabarro stress which arises from the variations in bond energies of atoms in the dislocation core as it is displaced is the probable mechanism controlling low-temperature deformation. The purpose of this research was to investigate the low-temperature plastic deformation of the bcc alloy Mg-14 wt pct Li-1.5 wt pct A1 to determine if the behavior of this alkali metal alloy might be analogous to that for other bcc metals. This alloy was selected because of its availability and its current industrial importance as a lightweight material for aircraft and aerospace applications. I) EXPERIMENTAL PROCEDURE Polycrystalline tensile specimens having cylindrical gage sections 2 in. long by 0.2 in. in diam were machined from as-received alloy sheet stock of Mg-14 wt pct Li-1.5 wt pct Al. Specimens were annealed in an argon atmosphere at 423°K for 4 hr and maintained in a kerosene bath together with the sheet stock to prevent corrosion. The resulting specimen microstructure consisted of a coarse uniform dispersion of incoherent precipitate MgLi2Al particles7 in a bcc 0 phase matrix having an average grain size of 150 p. Prior to testing the specimens were chemically polished in dilute hydrochloric acid. Comparison of tensile properties and microstructures of specimens cut from center and edge sections of the sheet stock revealed no effects of inhomogeneities in the sheet material. Tensile tests were performed on an Instron machine at crosshead speeds corresponding to tensile strain rates of 1.56 x 10-5 and 1.56 x 10"3 per sec. Stresses were determined to ±2 x 106 dynes per sq cm and strains to within ±0.0001. Average values of shear stress t and shear strain y reported were taken as one half the tensile stress and three halves the tensile strain, respectively. Flow stresses were taken at 0.05 pct strain offset. Test temperatures down to 77°K were obtained by immersing the specimens in constant-temperature baths. Lower-temperature tests were performed in a liquid helium cryostat to within ±2°K of the reported values. Prior to testing at the various temperatures and strain rates all specimens were prestrained at 2 35°K at a shear strain rate of 3.13 x 10-5 per sec to a stress level of 0.606 x 10' dynes per sq cm to obtain a uniform initial state. Additional tests were made to determine the effect of changes in strain rate and strain on the flow stress by rapidly changing the crosshead motion during testing. Shear moduli of elasticity, needed for analyses of the data, were obtained at several temperatures by a common technique of determining the resonant frequencies of vibrations of rectangular test specimens. 11) EXPERIMENTAL RESULTS Fig. 1 shows the experimentally determined flow stress vs temperature for two strain rates. Two distinct regions of behavior are evident. Below about 180°K the strong increase in flow stress with increased strain rate and decreasing temperature indicates that deformation is controlled by a thermally activated dislocation mechanism. At higher temperatures an athermal region is evident where the flow stress is independent of strain rate and only slightly dependent on temperature. The applied stress t to cause plastic flow was separated into two components:

Jan 1, 1969

By E. R. Parker, R. H. Thielemann

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By R. H. Thielemann, E. R. Parker

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By K. C. Ten Brink, Allen D. Garrison

A rrevious paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their composition, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions. Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. Experimental Procedure The difficulties involved in the measurements of the flow characteristics of plastic fluids are too familiar to recite. The possible applications of some of the well-known instruments to this problem have been adequately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measurement of clay or shale suspensions. Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first requirement is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1940

By K. C. Ten Brink, Allen D. Garrison

A rrevious paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their composition, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions. Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. Experimental Procedure The difficulties involved in the measurements of the flow characteristics of plastic fluids are too familiar to recite. The possible applications of some of the well-known instruments to this problem have been adequately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measurement of clay or shale suspensions. Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first requirement is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1940

By H. F. Johnson, C. S. Harloff

The Nichols series system of electrolytic copper refining has successfully maintained its strong competitive position in the copper-refining industry of today; therefore the improvements made in accomplishing this result are of interest. While additional interest would lie in specific comparisons of results obtained in series operation with those in multiple, we have refrained from such a comparison because it can be fair to both only when they are operating under similar conditions on the same grade of materials. Historical The Nichols Copper Co. started a small refinery at Laurel Hill, using its present system, about 1892. The details of the process in its early stage of development were kept strictly secret, so that no information was published or interchange of ideas permitted with the staffs of other copper refineries, where the multiple system was being developed at the same time. However, the fundamentals of the process and type of cell used today differ very little from their earliest form. All operations including loading and unloading of tanks, and all transportation as well, were carried on by hand. The plant remained in this condition with a gradual expansion taking place until the World War forced such a rapid development that little time or thought could be devoted to modernization or mechanical improvement requiring careful design or detailed planning. Considerable progress was made, however. (1) Large refining furnaces were developed. (2) The old expensive air-lift type of circulation was abandoned in favor of the present system. (3) Operating technique was gradually developed to a high point of efficiency. (4) Tank construction and lining were greatly improved, the first concrete tank being installed in 1915. (This tank is still in operating condition.) (5) A new power plant was constructed. (6) Fuel oil was substituted for lump coal on the refining furnaces. (7) Mechanical casting of the finished product was accomplished. During this entire period the plant was particularly fortunate in receiving only high-grade, clean copper bullion coming principally from the Phelps Dodge mines in Arizona. This, together with the lack of

Jan 1, 1934

By William Colby

INCREASING governmental control of human activities seems inevitable. Within the present generation railroad rates and the public sale of water, gas and electricity have been subjected to rigid regulation. The field of control is slowly but surely being enlarged, and it is the object of this paper to outline in brief space this tendency toward increased governmental regulation, as far as mineral resources are concerned. Our, dual form of government complicates the problem. We must deal not only with the powers of the Federal Government, but also with those of the individual States. In order to approach this question intelligently we must have some conception of the powers and jurisdiction of the States and the United States, respectively, over mineral lands and mineral production. Starting with the Federal Government we find it never owned any public domain within the States that formed a part of the thirteen original colonies and, for historical reasons, the same is true of Tennessee and Texas. The Mid-Western States were erected out of the public domain which was acquired by the United States through cession from the original States or by purchase from foreign nations. Congress early in the last century adopted a policy of leasing public lands containing lead deposits in a portion of this Mid-Western territory, but later abandoned that policy and disposed of such public, lands, mineral and non-mineral, outright so that they long since have practically all passed into private ownership and become subject to the general jurisdiction of the respective State governments. In the great public domain lying west of the Mississippi River, and in portions of some of the Southern States, the Federal Government adopted a new mineral land policy following the discovery of gold in California. (Acts of Congress of 1866, 1870, and 1872.) The mineral lands within these States, instead of being disposed of on the game basis as agricultural lands, as occurred in the Mid-Western States, were segregated from agricultural lands and sold under special laws intended to encourage mining, giving the miner the free right to locate and work these mineral lands without paying any royalty to the Federal Government. A miner could also obtain at slight expense a complete

Jan 1, 1930

By Joseph J. Yancik

From previous work, it was learned that relative strengths of blasting agents can be reasonably predicted from heats of detonation modified by their (D/D*)2 ratio.(1) Bulk Strength = Q x d x (D/D*)2 x K (1) In this equation Q is the ideal heat released during detonation, d is density, D represents actual detonation velocity while D* is ideal velocity. An energy transfer coefficient, K, was used to account for differences among rock strata in response to explosive loading. This equation gave reasonable, field supported strength values for oxygen balanced blasting agents. For aluminized nitrocarbonitrates and slurries which have high Q's the rating system predicted better strengths than were shown in the field. This discrepancy was felt to be related primarily to problems in calculating Q and D*. Theoretical calculations cannot take into account varying energy contributions from particulated aluminums whose reactivities vary substantially with physical properties. One approach to circumventing this problem would be to use a characteristic Q that is dependent on mass reactivity of ingredients as components in explosive formulations. Since the underwater testing method is capable of measuring a functional, relative energy release, it was chosen for study.

Jan 1, 1971

By M. M. Singh

Coal mine operators are obligated to mitigate or plan for subsidence under the new regulations. This paper presents the types of subsidence control measures that may be employed to meet these requirements, which include: changes in mining methods, strata stabilization after coal extraction, construction of specially designed surface structures and foundations to accommodate ground movements, and comprehensive planning and coordination of surface land use with underground mining. The basic principles of these techniques, along with specific procedures that may be followed to implement them, are briefly discussed. Subsidence control methods that are currently being investigated are mentioned.

Jan 1, 1985

By J. A. Collins

THE process of plastic extension of face-centered cubic single crystal-line rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellae are free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [112] direction in the axis of the rod. This process has been checked in many face-centered cubic materials and readily permits the preparation of specimens that have been sub-jected to various determinable amounts of shearing action. It is clearly of interest to study in such measurably strained specimens the development of a recrystallized structure on annealing and if possible detect the source of nuclei from which the new crystals grow. Strain-annealing experiments of this character have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs, the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae) at the conclusion of a test of from 0.08 to 0.57. A particular point was made of determining the crystallite rotation, or small angular range assumed by the octahedral slip plane after these various amounts of shear. The mechanism of recrystallization and the magnitude and effect of recovery on the recrystallization process was investigated.

Jan 1, 1940

By C. M. Shigley

The record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.' The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 to 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000- ooo-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation—the largest known magnesium plant utilizing sea water as its raw matcrial. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and 7 miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1949

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three-phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use. In the general evaluation of suitability of coals for coke making, particular attention is given to: 1) reserve, 2) ash and sulfur content, 3) inherent properties of forming strong, well fused coke, 4) expanding characteristics, and 5) blending properties. Items 1 and 2 are covered in detail in the first two phases of the survey, and coking behavior is considered in items 3 through 5. Problems is Coal Evaluation: Although not all coal beds of immediate or potential use to the coking industry in the Pittsburgh area have been tested for their coking properties, enough tests have been made to permit certain generalized statements. Virtually all the coals that will be used in this district are from the Appalachian region, and except for high oxygen coals from outcrops or stripping operations, they are coking coals. Hence the evaluation problem is not so much that of distinguishing between coking and noncoking coals as attempting to measure quantitatively differences in the coking and expanding properties of the better coking coals. Quantitative differentiation between good coking coals, is complex, since differences in their coking abilities are frequently of about the same magnitude as the precision of the test. Small-scale tests are generally unsuitable for measuring these slight differences, and there has been gradual acceptance of pilot-scale tests. Test Methods Employed: All the data reported here were obtained in two units known as the Bureau of Mines-American Gas Association (BM-AGA) carbonization apparatus and the sole-heated expansion oven. The BM-AGA unit, which consists essentially of a cylindrical steel retort about 18 in. diam and 26 in. high, carbonizes enough coal (180 lb) to allow evaluation of the coke by standard methods of the American Society for Testing Materials. The BM-AGA carbonization procedure and methods of testing the gas, liquid, and solid products have been described.' Expanding characteristics of the coals were determined in the sole-heated expansion oven," wherein the coal charge, heated from the bottom only, is carbonized under a constant applied force and the linear expansion or contraction is measured. Although results in this oven have never been quantitatively correlated with the expansion behavior of coals in conventional slot ovens, they are useful in assessing expansion behavior. In this report discussion will be confined to results obtained from these pilot-scale units, although the following data are available for most coals: proximate and ultimate analyses, free swelling index, agglutinating value, and plasticity. Sources of Coals Tested: In selection of coals for coke manufacture, economic considerations are as important as quality, and each coke plant balances these two factors to meet requirements of the most satisfactory coke at lowest price. Although these economic factors may in some instances outbalance small differences in coke quality, they are usually specific to each coke plant and cannot be given in any general statement. Recognizing that coal and plant operating costs are beyond the scope of the survey, the USBM evaluates the coking quality of various coals without regard to their competitive economic status. For the purpose of this article, coals of interest to the Pittsburgh district are arbitrarily defined as

Jan 1, 1958

By W. L. Fink, R. S. Archer

This paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent, beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium docs not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. Commercial Possibilities of Beryllium Alloys Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to thc strength and corrosion resistance of thc aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

By J. F. Nicholas

THE angles between the crystallographic planes in cubic metals were originally given by Bozorth and have been republished many times. Recently, Salkovitz2 tabulated the angles for the hexagonal metals (magnesium, zinc, and cadmium). he most commonly used metal which does not fail into either of these groups is tin, which has a tetragonal structure with an axial ratio of c/a = 0.54558 (99.99 pct purity, 25°C).² ccordingly, Table I has been prepared giving the possible values for the angle, 4, between planes of the types {HKL) and {hkl). The formula used was: Hh + Kk + LI — cos? = —--------------—-----------— A [(H2 + K2 + L2-a2c2(h2 + k2 + r;)] All angles are given correct to the nearest minute as this is sufficient for all practical purposes. Every angle depends in a different way on variations in the value of c/a, but even in the worst cases a variation of about 0.0003 in this ratio is needed to vary an angle by l', which corresponds to a temperature change of 20 °C or can be caused by impurities.

Jan 1, 1952