Search Documents

By D. F. Kaufman, E. D. Levine, L. R. Aronin

The deformation of' impure beryllium crystals by basal glide at room temperature invariably tevminates by basal cleavage after a few percent strain. It is generally accepted that .fracture of this type is caused by the splitting of low) -angle boundaries, or bend planes, by obstacles that restrict the motion of the bed planes in the deforming crystal. The details of such a process have been developed by Stroh, who showed that the high tensile stress norrnal to the basal plane in the region where the bend plane is split results in the propagation of a basal cleavage crack, provided there is no available dejorvrlatzon mode having a shear component normal to the basal plane It has been postulated that puvification of beryllium might lead to increased basal ductility by the vemoval of barviers to bend plane motion and possibly by the activation of nonbasal defor~rlation systems. Large increases in the amount of basal glide that can he sustained prior to fracture have been observed in crystals purified by zone refining. In each case, eventudal fracture was by sharp basal cleavage, suggesting that the split bend plane model still applies to tile fracture of beryllium of rensonably high purity. In the present work, calculations are made to show to what extent basal duetilits can be increased by purification while the split bend plane .fracture process remains applicable. Experimentally observed ductilities are generally somewhat lower than those predicted by calculation because of premature failure due to defects introd~cced during specimen preparation and testing. SEVERAL investigators1-4 have studied the deformation characteristics of beryllium single crystals of commercial purity, and have related the strong anisotropy of plastic deformation in single crystals to the problem of brittleness in polycrystalline beryllium. For most orientations, the principal deformation mode is basal slip, which, at temperatures between 300" and 900°K, begins at a critical resolved shear stress of approximately 1500 g per sq mm and terminates after 3 to 6 pet glide strain by cleavage on the basal plane in the neighborhood of (1120) bend planes that are formed during the deformation. This type of fracture, which is also observed in zinc at low temperatures, has been interpreted by stroh5 to be caused by the splitting of bend planes by obstacles to their motion. In the Stroh model, a (11.20) dislocation wall, or bend plane, moving along the slip direction under the action of the applied stress, encounters obstacles which cause part of the bend plane to be held up, the other part continuing to move. Stress concentrations are built up in the region where the bend plane is split, with a high tensile component normal to the basal plane, resulting in a microcrack at the end of the split wall. Because no deformation mode having a shear component at an angle to the basal plane is available to relieve the stress at the crack tip, the crack can propagate under a sufficiently high applied stress. The Stroh criterion for crack propagation is given by

Jan 1, 1964

By W. C. Roberts-Austin

The subject with which the Council of the American Institute of Mining Engineers has entrusted me is one of much interest. It has been so admirably treated in America by Prof. Carl Barus* that I should have hesitated to deal with it had not the adoption of pyrometric methods in England recently occupied much attention, especially in relation to metallurgical industries and research. I shall endeavor to show what is the present state of our knowledge of practical pyrometry by briefly tracing the history of the efforts which have been made to measure high temperatures. This paper will, therefore, be limited to the consideration of those forms of appliance which have either marked distinct stages of advance, or have remained in use with more or less modification through a considerable range of time. The earliest pyrometers were essentially thermoscopes, and although their graduation presented great difficulties, their importance as affording a means for the measurement of high temperatures has been recognized for centuries. It would be difficult to illustrate this better than by a brief record of the testimony which has from time to time been offered by those who have had to apply the heat of furnaces in research or in industry, and it is mainly for the sake of the light incidentally thrown on the progress of both that the following historical notes are offered. In the eighth century, Geber, the chemist, wrote a treatise on furnaces, and showed that he was familiar with many and varied means of applying heat; but he points to the difficulties that are met with in conducting operations at high temperatures, which he attributed to inability to measure heat, his actual words being: " sed quoniam non est res ignis, quae mensuari possit." t

Jan 1, 1894

By Hugh M. Roberts

In the spring of 1915, then a 30-year old geologist in the employ of the E. J. Longyear Co., of Minneapolis, Minn., I accompanied prospectors to ex- amine outcrops of supposed nickel ore situated a mile or two in from the shore of a lake in the Kenora district of northwestern Ontario. The deposit proved to be bog iron ore containing traces of nickel. We were stormbound there for three days, a circumstance which gave rise to a tale that was told at our fire one night. It seems that Sandy and Jock, two prospectors, were crossing the bay of a large lake in a canoe. They were bucking headwinds; the waves grew higher. Jock called out from the stern, "Sandy, can ye na pray a little." Sandy pressed his knees a little closer into the bow and, between strokes of his paddle, sought for words, which came haltingly, "Save us this time . . . Oh Lord . . . and we promise . . ." when Jock, peering through the spray sang out, "I would na commit yourself, Sandy, I think I see lond ahead."

Jan 1, 1965

By J. J. Pye, J. B. Drew

The surface-diffusion coefficients of Ni63 diffusing on low-index planes of nickel single crystals have been measured over the temperature range from 400° to 1000°C using a precision autoradio-gvaphic technique. The activation energy for sur -face diffusion appears to he the same on the {111}, {110), and (100) planes and amounts to -0.60 ev. This is in good agreement with the value (-0.62 ev) reported for (111) planes obtained by mass-transport techniques. In an earlier paper, the authors have reported self surface-diffusion coefficients on silver.' In that work, a deviation of the diffusion coefficients from linearity in the Arrhenius plot was observed at high temperatures. This effect was attributed to a loss of tracer atoms into the bulk by volume diffusion. The purpose of the present work was to extend the technique developed to the nickel surface-diffusion system up to the point where volume diffusion would come into play. The nickel system especially lends itself to this technique due to the high efficiency of the isotope in darkening the film and the large absorption of the weak radiation (0.063 mev /3- particle of the trapped tracer atoms. The diffusion coefficients and ictivation energy for different orientations on nickel can also be compared with a report published by Blakely and Mykura 2 where a mass-transfer technique was used. This paper reports the self surface diffusion of nickel on the low-index planes over a wide temperature range using a precision autoradiographic technique. EXPERIMENTAL PROCEDURE The experiment is similar to that described in the earlier publication consisting of a radioactive needle as a source resting on a flat, smooth, chemically polished surface annealed in a dynamic dry-hydrogen atmosphere. The needle is held snugly on the surface by a holder fabricated from commercially pure nickel. The point source is made by grinding down a small-diameter nickel rod until a tip of approximately 0.1 mm radius is formed. It is then etched and the needle tip plated with the radioactive isotope Ni63. Nickel single crystals were used whose main impurities were spectrographically determined as Co 0.05, Fe 0.007, C 0.005, and S 0.003 pct. The surfaces, oriented to within 1/2 deg of the low-index planes, were carefully mechanically polished and etched in a 50-30-10-10 hot solution of acetic, nitric, sulfuric, and phosphoric acids giving a smooth polished surface. The crystals were then washed in distilled water and alcohol. Annealing temperatures ranged from 400° to 1000°C with a furnace arrangement in which the crystals could be brought up to temperature in times short compared to diffusing times. The temperature was maintained constant to ±10°C. In the temperature range investigated, the ratio of the surface-diffusion coefficient to the volume-diffusion coefficient (Ds/Du) was 105 or more and the mean bulk-penetration values, calculated from literature values of volume-diffusion coefficients,3 were on the order of 10-5 cm. After the diffusion anneal, the sintered needle is removed, and both the radius of the needle point and spot left on the crystal face are measured. The crystal is then placed on photographic film. Diffusion profiles are obtained by scanning the film with a recording microdensitometer which has a slit width of 10µ. DISCUSSION AND RESULTS The experimental conditions are such that the source strength and needle radius are essentially constant and the time is adjusted such that the mean bulk penetration is small. An exactly analogous heat-flow problem has been considered by Carslaw and Jaeger4 and the solution can be written in integral form as:

Jan 1, 1964

By Carl R. Christiansen, James J. Scott

Advance mine planning, coupled with good mining practice, can be employed to develop underground space in stone mines for future industrial usage. To assure the developer the maximum return on his investment, initial planning should consider all aspects of the commercial operation, including surface layout, mining, and underground industrialization. The modular concept of mining to compartmentalize the space offers several advantages over conventional methods. Some expenditures can be considered as mining costs with a reduction of profit from stone production while lowering the capital requirements for conversion for usable space.

Jan 1, 1977

By A. K. Mukherjee, J. E. Dorn

A modified Peierls model is Presented for the rationalization of the asymmetric plastic behavior of single crystals of bcc metals. The model assumes that the asymmetry of slip arises from a tendency toward asymnetric splitting of the a/2[111] screw dislocation. The approach differs from former theories however insofar as it assumes that the splitting is so minor ttut only the core energy is modified and that no real partial dislocations exist. As a consequence, the concepts of a line energy of a partial dislocation, interaction between partial dislocations, constriction energies, and stacking fault energies are not invoked. Instead the present analysis is based on a specialization of the Peierls mechanism which assumes an asymmetric dislocation core which is modified by the effective stress and permits cross slip. The theoretical predictions on the stress-temperature -strain rate and orientation relationship agree qualitatively with the limited experimental data that are currently available. Additional experimental work over wider ranges of conditions is suggested to provide more complete evaluation of the possible validity of this theory. RECENT experimental investigations on the low-temperature thermally activated deformation of bcc metals have confirmed the existence of several unique orientation effects. These will be described with the aid of the standard stereographic projection shown in Fig. 1. If slip were determined exclusively by crystal symmetry, the deformation characteristics would be symmetrical about X; = 0 and independent of whether the specimen were subjected to a tension or a compression stress, regardless of what combinations of slip planes might be operative. Experiments, however, reveal that neither of these symmetry based predictions are valid. A schematic representation of the commonly observed asymmetry of both the yield stress and the plane of slip is shown in Fig. 2. A reversal of the direction of stressing results in an inversion of the asvmmetric behavior. 1) Asymmetry bf Yielding. A detailed investigation on the asymmetric yielding in an Fe-2.7 pct Si alloy was repoEted by Tabka, Tikeuchi, and Furubayashi,1 Similar trends have been observed by Keh and Nakada on iron,' Stein on molybdenum,3 Bowen, Christian, and Taylor4 on columbium, Sherwood, Guiu, Kim, and pratt5 on Ta, Cb, and Mo. The degree of asymmetry not only depends on the atomic number and alloying but, in all cases that have been examined, it also increases with a decrease in the test temperature. 2) Asymmetry of the Slip Plane. Asymmetric $I-~: curves of the type shown in Fig. 2 have been found for several Fe-Si alloys6-8,1 and columbium.4 There is general agre_ement that near X: = 30 deg slip occurs by the [111](211) mode so that ?1 = 30 deg. As X; decreases it appears that [111](211) to [111](101) cross slip takes place leading to slip band traces on intermediate planes. And as xi approaches 0 deg, sharp

Jan 1, 1970

By P. Somasundaran

An experimental and theoretical treatment of the depressing effect of inorganic electrolytes on the amine flotation of quartz is presented. Experimental data obtained for the amine flotation of quartz as a function of pH with potassium nitrate as depressant was used to test the models for the effectiveness of inorganic ions as depressants. The validity of commonly used assumptions are examined. The surface tension data obtained for dodecylammonium acetate solutions as a function of KNO3, concentration indicated that the collector adsorption on bubble cannot be neglected in the treatments, since this adsorption changes significantly with the addition of the inorganic electrolyte. It also indicated the possibility of significant changes in the specific adsorption potential of the collector occurring with the addition of inorganic electrolytes.

Jan 1, 1975

By W. E. Ruder

IT has been pointed out by Stead 1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper 2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions, promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Are. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703° C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750° C. for 0.5 per cent. Si to 860° for 6 per cent alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730° and 750°.

Jan 12, 1913

By P. M. Robinson, M. B. Bever

THE heats of formation at 273°K of the compounds InBi, In2Bi, and TIBi2 have been determined by metal solution calorimetry with bismuth as solvent. The published information on the thermody-namic properties of these compounds is limited. The structure of the compound InBi (mp, 383°K) is tetragonal of the PbO (B10) type.1 The compounds In2Bi (mp, 362°K) and TIBi2 (mp of highest-melting composition, 486°K) are now believed to have structures of the NizIn (B8) type273 and not the A1B2 (C32) structures reported earlier.4, 5 The compounds In2Bi and TIBi2 have limited homogeneity ranges at room temperature, while the compound InBi has no detectable homogeneity range.' Samples of the compounds were prepared from 99.99 pet Bi (Mallinckrodt Chemical Works), 99.999 pet in (American Smelting and Refining Co.), and 99.99 pet Tl (Amend Drug and Chemical Co.) by melting the components in sealed, evacuated Vycor tubes. The compounds InBi and in2Bi were of the stoichiometric compositions. The compound TIBi2 contained 40 pet T1; this composition was chosen because at room temperature the alloy of stoichiometric composition does not lie within the homogeneity range.' The melts were held approximately 50°C above the liquidus for 8 hr and then quenched into iced brine. The samples were homogenized for 48 hr at temperatures 20°C below the temperature of complete solidification. Metallographic examination of sections taken from the center and the ends of the ingots did not reveal second phases or segregation . The heats of formation were determined as the difference in the heat effects on solution of a compound and of a mechanical mixture of its components added from the reference temperature of 273°K to liquid bismuth at 623°K. The details of the calori-metric procedure and method of calculation have been described elsewhere? The calorimeter was calibrated by adding bismuth at 273°K to the bismuth bath at 623°K. The calculated values of the heats of formation of the compounds, listed in Table I, are based on a value of 4.96 keal per g-atom for the difference between the heat contents of bismuth at 273" and 623oK7 No published values are available for the heats of formation of the compounds InBi and In2Bi. Hultgren et a1.7 have calculated a value of -0.50 i 0.10 keal per g-atom for the heat of formation at 423°K of the compound TIBi2 containing 40 at. pet T1 from heat-content measurements in the range from 398" to 700°K and the heats of formation of the liquid alloy. The difference between this value and the value of -0.66 * 0.01 keal per g-atom at 273°K is too large to be attributed to a difference between the heat capacities of the compound and the components over the temperature range 273o to 423oK7 However, the direct determination of the heat of formation by a calorimetric method should give a more accurate value. The heats of formation at 273°K of the compounds InBi and In2Bi lie on a straight line when plotted as a function of composition, Fig. 1. The compound In2Bi, therefore, appears to be barely stable with respect to its neighboring phases. In order for the free energy vs composition curve to be concave towards the composition axis, the entropy change on formation of In2Bi must be more positive than that on formation of InBi. As the compounds are ordered,2, 3, 8 there is no configurational entropy change on formation. The difference between the entropy changes on formation of the two compounds, therefore, is probably associated with the vibrational entropies. In view of the low heats of formation, the changes in vibrational entropy, due to changes in bond strength on formation of the two compounds, are likely to be small. Owing to the volume contractions on formation of the two compounds,5 the vibrational entropies probably decrease slightly but the decrease of the vibrational entropy of InBi is expected to be larger than that of In2Bi.

Jan 1, 1965

By John H. Walthall, Raymond L. Copson, Travis P. Hignett

In October 1942, the War Production Board requested the Tennessee Valley Authority to undertake investigations to determine the feasibility of producing alumina suitable for reduction in aluminum cells, from clays and other domestic materials, by a lime-sintering, soda-ash leaching process. The work was undertaken by the chemical engineering staff of the Authority under the general direction of the War Metallurgy Committee of the National Academy of Sciences. The investigation included small-scale tests to determine the most suitable conditions for the process, and construction and operation of a pilot plant to obtain data for evaluation of the process and for design of a plant. The results of this investigation are described in the present paper. Sources of Alumina Alumina for the commercial production of aluminum is obtained from bauxite by the Bayer process. The tremendous demand for aluminum for wartime uses is causing rapid exhaustion of the high-grade bauxite deposits in the United States. On the other hand, there is an abundance of aluminous materials such as clay and lower grades of bauxite, which are not suitable for treatment by the Bayer process because of their high silica content. The Tennessee Valley Authority has conducted research and pilot-plant work for more than 5 years on methods for the production of alumina from clay and low-grade bauxite. Particular attention has been given to the high-grade white kaolin found in Carroll County, Tennessee. Exploratory drilling has demonstrated that at least 4 1/2 million tons of kaolin containing in excess of 34 per cent AlzOI is available in this area by strip-mining methods. It has been estimated that hundreds of millions of tons of clay of similar quality occur in the Tennessee Valley region. The Process The process is illustrated in the flowsheet (Fig. I), and consists essentially of the following steps: I. Heating a mixture of clay and limestone to form a sinter containing calcium aluminate and dicalcium silicate. z. Leaching this sinter with a dilute sodium carbonate solution, to form a sodium aluminate solution and a calcium carbonate, calcium silicate residue, which is discarded. 3. Treating the sodium aluminate solution with carbon dioxide to precipitate aluminum trihydrate and regenerate the sodium carbonate solution, which is recycled. 4. Heating the aluminum trihydrate to produce alumina. The process was considered promising because of the abundance and cheapness of the two raw materials, clay and limestone; and because, as compared with an acid process, smaller amounts of critical

Jan 1, 1944

By Walter V. Knopp, Laurence Delisle

The aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixtufe of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals . normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion correspending to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected.that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low COSt material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, that is, finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemelltal powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: I. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. General Procedure The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1949

By R. D. Reiswig, J. M. Dickinson

The 0s-Ir equilibrium diagram was determined. The diagram is of the simple peritectic type, with a peritectic temperature of about 2660°C. The solid miscibility gap is narrower than previously reported, the nearly vertical solvus lines occurring at about 42 and 63 wt pct 0s. Widmanstaetten figures resembling martensite in some of the two-phase alloys account for a previously suspected transformation. In view of the long history of use of such alloys, it is surprising that the 0s-Ir equilibrium diagram has not yet been completely determined. The boundaries of the miscibility gap in this system have been estimated to be between 24 and 39 wt pct 0s and 79 and 100 wt pct OS. It has been predicted3 that alloys of ruthenium, osmium, and rhenium with the fcc platinum metals should solidify peritectically in their two-phase regions. The metallographic examination of natural osmiridium alloys has been said4 to indicate, by the presence of a martensitic structure, the existence of a transformation or a phase separation. On the basis of superconducting transition temperature measurements, a 70 at. pct 0s alloy was found5 to be two-phase prior to annealing. EXPERIMENTAL The elemental components used in this work were obtained from several suppliers as sponge. The purities, stated by each supplier to be in excess of 99.8 pct, were confirmed in each case by a semiquantitative spectrographic analysis. The pure components were premelted in an inert-gas tungsten arc furnace with the evolution of some fume, crushed, and pickled for use as alloy melting stock. Upon arc melting to the final compositions, no fume evolution was observed. Because weight losses of the order of 15 mg or less were observed in preparing alloy buttons weighing 15 g, "synthetic analyses" were used in determining the compositions of the alloys. Alloys used in this investigation contained 15, 20, 33, 40, 42, 43, 45, 50, 55, 60, 63, 64, 66, 70, 79, and 80 wt pct 0s. Heat treatments of the alloy buttons and pieces thereof were performed in a previously described6 tungsten tube furnace under pressures of 105 torr or less. It was found that homogenization treatments on the specimens were essential to remove the severe coring which was present, a 3-hr treatment above 2300°C removing all the metallographi-cally visible evidence of coring. Following the various heat treatments, the specimens were "vacuum-quenched" by melting a tungsten fuse wire and allowing them to drop onto a water-cooled copper plate. In a few instances, specimens were quenched into molten tin for comparison, but no difference was apparent. Vacuum-quenched specimens cooled from 2400°C to below a red heat in less than 60 sec. Typical equilibration times varied from 3 hr above 2300°C to 88 hr near 1100°C. The utilization of successively longer equilibration times and the approach to equilibrium from both directions indicated that the times used were sufficient to give a close approach to true equilibrium. Heat-treatment temperatures were measured with a calibrated Leeds and Northrup optical pyrometer through a 0.120-in. lateral sight hole in the tungsten heater tube. It was known that the assumption of black-body conditions inside the 1-in.-diam by 10-in.-long tube was unwarranted. The empirical results of work with thermocouples and melting

Jan 1, 1964

By Paul Tyler

THE ferroalloying elements are connecting links between the steel industry and the nonferrous metal industries. Although ferroalloys are distinctly nonferrous themselves, they serve the steel industry either in the manufacturing process or in modifying the product-in some cases so that it may compete in the markets with nonferrous metals. Of the 92 elements generally accepted by chemists as constituting the primary building blocks of matter, all but the very rarest have been investigated with a view to employing them in steel manufacture. The surprising thing is that so few have been found commercially acceptable. Despite the relatively small number of elements involved, the employ-ment of alloys in steelmaking is one of the most complicated and probably one of the least well understood of modern industrial enterprises. A great deal has been written regarding the action of individual elements and a profuse and somewhat acrimonious literature covers pretty much the whole field of ferroalloy ore supplies. In the middle ground between the miner and the steelmaker developments are less carefully watched by most observers, and except for an occasional description of the technique of some conversion process or the tariff hearings in Congress, very little is said about them. The purpose of the present paper is to describe in relatively nontechnical terms this highly complex industry and to study its relations to our national progress.

Jan 1, 1933

By S. B. Christy

The fact that many millions of gold have been extracted by the cyanide process, during the last five or six years, from South African tailings which could not be profitably worked by any other method previously tried upon them, lends a peculiar practical interest to this branch' of metallurgy. Numerous writers have recently made valuable contributions on the process without exhausting the many complexities of the subject. Among the first American writers on the subject in its modern aspect were two former students of the University of California, Mr. Louis Janin, Jr., and Mr. Charles Butters. Young Janin was one of the first to enter this field, and performed much useful experimental work in the early stages of the history of the process. At about the same time, Mr. Charles Butters, who had left California to erect chlorination works for the Robinson mine at Johannesburg, became interested in the cyanide process, and, after getting the chlorination plant in working order, put up, for working the tailings from the Robinson mine, a cyanide plant which achieved the first large-scale success ever made with this process. The papers which Charles Butters, together with John E. Clennell and Edgar Smart, have contributed on the chemistry of the process, were among the first to give any adequate idea of its nature.* Another important contribution to the literature of the subject is the paper of Dr. A. Scheidell, published in 1894 as a " Bulletin of the California State Mining Bureau." This contains an admirable summary of the state of the art at the time of its publication.

Jan 1, 1897

By F. A. Schaufelberger

Early work on chemical precipitation of metals from metal salt solutions is reviewed. The chemistry and thermodynamics of precipitating copper, nickel, cobalt, and cadmium metals by reaction with hydrogen are discussed. Mechanisms of metal precipitation, nu-cleation, growth, and agglomeration are reviewed, as well as some solubility phenomena of cleation,gases and solids at elevated temperatures. Experimental data presented deal mainly with the reaction of copper sulfate solution with Hz. METAL can be recovered from a leach solution either indirectly by precipitation as a compound that is later reduced or directly by electrolysis, cementation, or chemical reduction, for example, with hydrogen. The widely used electrowinning processes suffer from the inefficiency of converting fuel to low voltage dc and from low current efficiency when complete recovery is attempted. With the batch hydrogen reduction methods outlined here, a unit of fuel converted to hydrogen in modern gas reform plants will make two to three times as much metal as can be obtained with electrolysis. With continuous hydrogen reduction, four to six times as much metal is obtained. Precipitation by reducing a metal salt solution with H, has been known for almost 100 years.' Commercial use of the process, however, awaited the research and development program initiated by Chemical Construction Corp. Within the last few years this program has brought about construction of commercial plants, listed on p. 701. Ideal hydrogen reduction will precipitate a pure metal from a solution obtained by commercial leaching methods at a rapid rate without excessive temperatures and pressures. The metal precipitate will be of desired size and density, less than a percent left in the vessel being deposited on the wetted parts. The present discussion will outline Chemical Construction Corp.'s early development program and will discuss the chemistry and mechanics of reducing copper, nickel, cobalt, and cadmium from solution by H2. Work on selective reduction of nickel from cobalt has been described earlier.2 The article is not concerned with precipitation of copper by disproportionation of cuprous solutions where yield is limited" to 50 pet.* It does not discuss use of gaseous reducing agents other than hydrogen, such as SCV which may lead to contamination with sulfur, or CO," which is considerably more expensive than hydrogen and produces a gaseous reaction product, CO2.† The article does not include use of other nongaseous reducing agents: which are far more expensive than CO. Also, notes on the history, engineering design, and performance of commercial plants have been given elsewhere." It will be shown that a pure metal can be precipitated by reduction with hydrogen from solutions obtained by commercial leaching methods when the solution cohposition is controlled and proper acidity, proper metal ion concentration through controlled complex formation and hydrolysis, and adequate agitation for suspension of metal and for transfer of reducing gas are maintained. Reasonable temperatures and pressures are used which are less excessive than those used by previous workers, although they are maintained at above equilibrium values because of process kinetics.' It has also been found necessary to induce nuclea-tion and to control growth and agglomeration in order to get a powder product of suitable physical properties. Review of the Literature Muller, Schlecht, and Schubardt of I. G. Farbenm claimed a successive reduction of silver, copper, nickel, cobalt, and zinc from ammoniacal solution by applying progressively higher temperatures and hydrogen pressures. Metals produced by this technique were not pure, since no attempt was made to adjust the solution composition between the different reductions. It is doubtful that the zinc product contained any metallic zinc. The major contribution to the literature" was made by the Ipatiews,12 who prepared platinum, iridium, copper, nickel, cobalt, lead, tin, arsenic. antimony, and bismuth at often extreme conditions, up to the critical temperature of water (373"C), at 1500 to 7500 psi, for as long as several days. Even cadmium and zinc were claimed to have been observed in trace quantities precipitated together with basic salts. In the early experiments solutions were not stirred. Extensive formation of oxides and basic salts occurred. probably long before sufficient hydrogen could be supplied in the unstirred liquid to decrease the metal concentration in solution by reduction. The importance of hydrogen pressure was

Jan 1, 1957

By R. S. Handy

DOES hand-sorting of mill feed pay? The fact that the practice is so general would seem to indicate that there must be good reasons for following it; yet, to my mind, the advantage in many cases is doubtful enough to invite a thorough discussion of the subject, in an effort to determine under what conditions hand-sorting does pay. A typical sorting plant in the Coeur d'Alene district handles about 800 tons of mine-run ore per day. The material is run over a grizzly with about 4-in. opening; the oversize is crushed to about 4-in. size and joins the undersize, and the whole product is washed and screened on trommels with about 1 ½ -in. openings. The oversize from these trommels is spread on a belt and the waste and first-class ore are sorted out by hand, the residue being further crushed, and passes, together with the trommel undersize, into the mill feed bins. About 50 tons of shipping ore and 150 tons of waste are sorted out per day, leaving about 600 tons of mill feed. To sort out this material requires 20 ore sorters and five bosses and repairmen. The normal cost of hand-sorting is about 16 c. per ton of run-of-mine ore, or 65 c. per ton of material sorted out. I believe that straight crushing and milling of the run-of-mine ore, in this case, is not only cheaper, but is metallurgically moree canonical and efficient than hand-sorting followed by milling of the residue. At one of the Bunker Hill rock-houses, 1250 tons of run-of-mine ore are reduced to pass 30-mm., or about 1 ¼ -in. opening in six hours, requiring five men. The equipment and the power consumed are not greatly different from that required in a sorting plant of the same capacity, and the normal cost of thus preparing the feed for milling is under 3 c. per ton of mine product. The relative cheapness of this method as against hand-sorting is thus clearly established, the saving being about 13 c. per ton. If there is any virtue in hand-sorting, then, it must lie in the metallurgical results achieved.

Jan 4, 1918

By AIME AIME

THOUGH the dust-control systems in the crushing plants and other buildings at Morenci do not differ materially from similar installations in other large copper reduction works, it is probable that in few other plants has as much attention been paid to the dust problem. Possibly the most striking feature of the Morenci installation is the manner in which the necessary equipment has been built into the various structures, and the absence of unsightly pipes, ducts, and fan houses. That this result has been attained is due, in no small part, to the basic conception that the control of the dust in a milling plant should be an essential part of the process itself and not something to be tacked on later after the plant is in operation. The control systems were designed and developed along with the general plant construction program and when the first car of ore was dumped into the crusher the dust-control equipment was ready.

Jan 1, 1942

The Candelaria deposit was first discovered by Spanish prospectors in 1863; but its silver ore was not exploited on a large scale until 1873, when the Northern Belle mine was opened. The first Northern Belle mill was built at Belleville, 13 km (8 miles) to the northwest. From 1876 to 1886 the Northern Belle paid over $1 million in dividends each year. In 1882 a 43 km (27 miles) pipeline was built to Candelaria from the White Mountains to the west to furnish water for the mills and town at Candelaria; it was 100 mm (4 in.) in diameter, hand- riveted, and made in England. Sections of this pipe are used. as claim posts today. At its terminus at Metallic City, above Candelaria, a large concrete reservoir was built and called Metallic Lake. It is being used today by Candelaria Partners. Production at Candelaria declined after the mid-1980s, revived for a short period in the early 1890s, and during the 1920s a 300 ton mill operated for three years. Candelaria Partners is owned jointly by Occidental Minerals and Congdon and Carey, with Occidental being the operator. An engineering study done in mid-1979 resulted in engineering for the plant commencing in late that year and heap leaching being started in September 1980. Two million tons of ore per year containing 108 g Ag and 0.28 g Au per mt (3.15 oz Ag and 0.008 oz Au per st) will be mined from the Lucky Hill and Mount Diablo .areas about 1.6 km (1 mile) up Pickhandle gulch from the heap leaching operation. Waste -to -ore ratio is about 2:l. Ore is mined by front-end loaders and hauled by 85 ton trucks to the primary crusher, a 1,070 by 1,780 mm (42 by 70 in. ) gyratory. Primary crushed ore is conveyed to a stockpile of 10,000 tons live capacity from which it is reclaimed by hydraulic reciprocating feeders and conveyed to the crushing and agglomeration facility. This unit is composed of a 1.8 m by 2.6. m (6 ft by 12 ft) double deck screen, a 2.1 m (7 ft) standard cone crusher, and three conveyors. At the conveyor transfer points NaOH and NaCN solution is sprayed on the ore as it falls through a row of 75 mm (3 in.) hanging steel bars. During this process of turning and dividing the ore, the fines agglomerate with the coarse ore to give better percolation for the leach solution on the heaps. Provision was made for the later addition of 2 kg per mt (4 lb per st) of cement to aid in the agglomeration. Agglomerated ore at minus 50 mm (2 in.) size is then conveyed to a 390 mt (430 st) loadout bin where it is transferred to 85 ton rear dump trucks for haulage to the leach pads.

Jan 1, 1981

By D. S. Newton

Introduction Historically the production of zinc dust has been based upon residual and secondary zinc. Using horizontal retorts filled with diecasting scrap, galvanizers drosses and sweater billets, dust has been produced by condensation into static condensers on a 24 hour cycle. Although fairly flexible as regards input materials the process is not amenable to close control of the product, is labour intensive and unless carefully run can cause fume problems. With a steadily increasing demand for zinc dust of consistent properties and higher quality there is a demand for an improved method of manufacture in which dust can be produced continuously and which is capable of close control thus ensuring a minimum amount of oversize or unsaleable material. The Process in use in the works of Imperial Smelting Corporation (Alloys) Ltd. in England, and in Canada and Holland, satisfies the criteria stated above, and has proved to be easy to control with a minimum labour demand.

Jan 1, 1970

By Bernhard Blumenthal

A melting process was developed by which high purity electrolytic uranium crystals can be converted into sound ingots without serious contamination. Careful preparation of the crystals, melting in a high vacuum, and directional solidification led to a metal of better than 99.993 wt pct purity. The metallographic examination showed a substantially clean metal with only residual amounts of a second phase which responded to heat treatment. The density of high purity uranium is 19.05 g per cu cm. FOR the study of the fundamental properties of uranium and its alloys, a base metal of high purity is needed, and an investigation was started at Argonne several years ago to examine various methods of preparing high purity uranium. Early success was achieved by the fused salt electrolysis process in preparing high purity metal in crystal form,' and the problem became that of melting the crystals into ingots without contamination. The electrolytic crystals contained a few ppm of heavy metals, less than 15 ppm C, and large quantities of potassium and lithium in the form of trapped fused salt electrolyte. On melting in vacuo in magnesia or urania crucibles, the metal picked up considerable quantities of carbon and some iron, copper, and silicon but lost most of the potassium and lithium. It was not metallographically clean, and much research work was necessary to determine the optimum melting conditions for minimum contamination. This work has resulted in the development of a melting procedure by which sound ingots can be prepared with only a limited contamination by carbon. In the section entitled "Melting of the Electrolytic Metal," the equipment and processes that have been developed for melting the electrolytic crystals are described in detail. The "Metallography" section is devoted to the metallography of high purity uranium, and the section "Density of High Purity Uranium" contains the first property measurement on high purity uranium—a density determination. Melting of the Electrolytic Metal Apparatus—Melting and Vacuum Equipment: Uranium may be melted in either resistance or induction-type electric furnaces. Resistance heating was found to be preferable to induction heating for melting down the electrolytic crystals, for several reasons: Although induction heating permits fast heating, this advantage cannot be utilized when crucibles with limited thermal shock resistance are used. Temperature control of induction-heated melts is poor, and the stirring effect increases the rate of contamination of the melt from the crucible, slag, or the furnace atmosphere; liquation and controlled solidification are difficult to carry out. Because of these objections, resistance heating was chosen. A 10 kw Globar resistance furnace of low heat capacity permitted uniform heating of a uranium charge to its melting point in 45 min. The furnace was insulated with a removable aluminum shield so that, after melting and removal of the shield, the furnace could be quickly cooled to room temperature. The furnace was equipped with an apparatus for directional solidification; see Fig. la. The crucible was suspended in the center of the furnace; and when the melting was complete, the crucible was slowly lowered into the cold end of the furnace tube. Solidification took place upward from the bottom; and when the rate of lowering was small, a sound ingot free from sink holes and shrinkage cavities was produced. To remove the large quantities of gas contained in the electrolytic crystals, melting in a high vacuum is mandatory. While, from the standpoint of contamination, melting in a highly purified argon atmosphere appeared feasible, lithium and potassium removal proved less efficient under such conditions. Also, a vacuum-melted ingot has a cleaner surface than one melted in an inert atmosphere. The vacuum system must be of very high pumping speed and leak tight so that a vacuum of less than 2x10-7 mm Hg is attainable when the system is pumped down cold. The system must have a high pumping speed, so that the pressure maximum which may rise to 1x10-4 mm during heating can be quickly reduced

Jan 1, 1956