Search Documents

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. ' The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By Ole Singstad

THE legislatures of New York and New Jersey, determined in 1919 that a vehicular tunnel should be built under the Hudson River. On July 1, 1919, an engineering staff was organized with the late Clifford M. Holland as chief engineer, and this staff was given a number of problems to solve, such as location, size, type of tunnel, method of construction, method of ventilation and cost. After a period of preliminary investigations and studies it was decided to build the tunnel at Canal St., New York, connecting 12th St., Jersey City. This is the center of the heaviest traffic across the Hudson River. It was also decided to build two tunnels-one for west-bound traffic and one for east-bound traffic-the tunnels to be of cast iron, built up of segments and bolted together, each tunnel to have a roadway 20 ft. wide and a clear heat room of 13 ft., 6 in. This is to provide for two lines of vehicles in each direction. The tunnels have an exterior diameter of 29 ft., 6 in. The interior lining is of concrete, the sidewalls tiled with a vitreous white tile and the roadways paved with granite block. The entrances and exits at both ends are separated by two blocks so as to reduce traffic congestion. BASIS OF VENTILATION It was recognized very early that one of the most important problems confronting the engineers was a proper ventilation system. It was estimated that each tunnel as planned would have a traffic capacity of 1900 vehicles per hr. The tunnels are 8500 ft. long between portals, and it was considered that the ventilation should be based on all of these vehicles being operated by gasoline engines. That presented a problem in ventilation unlike any other either in magnitude or character.

Jan 8, 1926

By J. M. McDowell

A study has been made to deter~r~irre how the behavior of a water drivee reservoir changes as a function of the permeability of the formation and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rote of nat11rn1 water influx is also studied, (IS well as the influence on the influx of the position of water injection we1ls with reference to the oil-water contact. The results are determined by the use of an electrical reservoir analyzer and are plotted as families of curves of pressure, natural water influx, and water injection vs time or cumulalive production. Two size aquifers are studided. One is limited with a 36-inile radius, and the, other approximates an infinite reservoir. The field remains the same in all respects for the completed. study except that the permeability is changed to agree with that assumed for the aquifer. 1 N TR ODUCTI ON this study was undertaken in -dcr to determine how the pres- sure decline and water influx of a water drive field would change as a function of the rate of fluid withdrawals, as a function of the permeability of the formation, and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rate of natural water influx was also studied as was the position of water injection wells with reference to the oil-water contact. The information has been determined by the use of an electrical reservoir analyzer1, sometimes referred to as a Carter type analyzer. This instrument is an analog type computer which can be set up to represent a water-drive oil field. It can reproduce the past performance of the field in terms of analogous electrical quantities when the proper circuit analog of resistors and condensers has been determined, also, it can determine the future behavior for any method of production which may be selected, or permit the comparison among several different methods. Although most applications of the reservoir analyzer"" have been to thc study of specific field performance, it is intended to use the analyzer here to help understand how various reservoir characteristics effect the final performance of the field and to sec under what conditions water injection will be of benefit and to what extent. Within the oil industry the performance of water-drive reservoirs was first described analytically by LV. Hurst' and M. Muskat2 for certain types of boundary conditions. The solutions of the equations developed involved products of exponential functions and Bessel functions. Later publications by Hurst4 and van Ever-clingen" and the hooks of Muskat6 gave further information on reservoirs with other boundary conditions. They also presented rather extensive curves and tables to help evaluate the analytical expressions involved. A rccent series of publications by Chatas. bascd on the work of Hurst and van Everdingen, gives quite complete charts and tables of data to evaluate the pressure decline or water influx in infinite or limited radial reservoirs. and in linear reservoirs. The curves in all of these publications are given in dimensionless form

Jan 1, 1956

By C. A. Heiland

The following summary is written for the benefit of the practical operator in the nonmetallic field who wishes to know what geophysics has done and may be expected to do in his line of work. His problem is quite different from that of the geophysicist who has operated with various or all methods and has followed the literature, and who is assumed to be familiar with the geologic possibilities and limitations of each method. This article is not written for the latter, although he may be interested in the four or five hitherto unpublished surveys described. To the operator, on the other hand, geophysics is only secondary. His problem is to determine which geophysical method is best suited to his special needs. If he wanted to know, however, which method could be used to locate a certain material of given physical properties, building stone, for instance, he would have to wade through a tremendous amount of geophysical literature, bibliographies and articles, before he could find what he wanted. Therefore, the purpose of this summary is to present the geological problems first and then to discuss the comparative merits of the geophysical methods that can be, or have been, applied. Choice of Geophysical Methods in Oil, Civil and Mining Engineering In the first two of these fields, the geological problems are not nearly so complex as in the metal and nonmetallic mining fields. The selection of the correct geophysical method in these fields is not nearly so difficult for the operator. For oil prospecting, his problems have been discussed exhaustively by E. DeGolyer.(1) † In civil engineering (foundation and ground-water work), the usefulness of electrical methods has been so well established that there is hardly any choice of other methods at present. The situation may be changed in the future with the perfection of the seismic reflection method for shallow depths. In the mining field the operator and often the geophysicist himself finds difficulty in determining which method is best suited for a given

Jan 1, 1934

By Arthur Taggart

THE major portion of the work described in this paper was performed by R. W. Young,+ a graduate student in the department of Mining and Metallurgy, Sheffield Scientific School, Yale University, working under a cooperative agreement between the Hardinge Conical Mill Co., the Sheffield Scientific School, and himself. Since this cooperative scheme is at present in effect in the case of a considerable number of other students in the department and since it is the hope of the school that the privilege thus extended may be utilized even more freely in the future by mining and manufacturing companies, it may not be amiss at this point to give a summary of the general plan. Briefly it is as follows: A graduate student, whose undergraduate work in this or other universities shows promise of ability to handle research work, is chosen by conference between the company and instructor involved. The aim of the company in the agreement then entered into is to obtain the solution of one or more of the technical problems with which it may be confronted, or, at the end of 1 or 2 years, to obtain as an employee a man especially trained in its work. As. a means to accomplish one or both of these ends, the company furnishes the machine, apparatus, or material to be tested and pays the student during his graduate work a small salary, usually just sufficient to cover his living expenses, tuition and fees. The aim of the student is special training along a line in which he is particularly interested, the attainment of his advanced degree, and the chance to show to his future employer ability to handle such problems as may be presented to him. In return for the financial aid which he receives he agrees to devote at least half of his working time to the special problem submitted by his company. The other half is devoted to study of the collateral subjects required by the department for the granting of the degree which the student seeks. The student further agrees to enter the employ of the company in question at a wage not greater than that paid in like positions to recent graduates not specially trained and to remain with his employer at such wage for at least 1 year. If the student is to obtain a degree, the special work forming the basis of his investigation must be such as will involve real research and not mere routine manipulation. The subject is chosen by conference between the three parties to the agreement. The work is carried on under the direct supervision of the instructor involved. The school furnishes the general laboratory and library equipment essential to the pursuit of any extended investigation, In

Jan 4, 1917

By R. G. Hudson, L. Yang

In electrochemical separation of metals, it is necessary to control the potential applied between the electrodes so that only the desired electrode reactions can occur. A knowledge of the minimum potential needed for a given electrode reaction to take place continuously is therefore pertinent to the success of the process. In molten chloride systems at high temperatures, activation polarization is believed to be small,1,2 so the minimum potential needed for the electrolytic decomposition of a molten metal chloride MC1n (n = valence of the metal ion) is therefore essentially the equilibrium electrode potential E of the metal-chlorine galvanic cell in the solution. If the decomposition products are pure M and chlorine at a pressure of p atm, E*Eo-rt/nf in [i] Since EO (the standard electrode potential of MCln) is a constant at a given temperature and R (the gas constant), and F (the Faraday's constant) are all constants, the variation of E with the electrolytic bath conditions is largely determined by the effect of the latter on the activity of the metal chloride amcln (standard state = pure MC1,). Measurement of E and study of how amCin varies with temperature and concentration, the nature of the solvent, and that of the coexisting solutes are therefore pertinent in the selection of optimum operating conditions for the electrochemical separation of metals. Because of its low melting point, high decomposition potentials of its components, and the low solubility of heavier metals in it, the LiC1-KC1 eutectic melt is a useful solvent and has been used in the electrodeposition of Mo,3Ce,4 and u5 metals. Senderoff and Brenner3 measured the potentials of Zn/Zn++, Fe/Fe++, Cu/Cu+, Mo/Mo+++, and Ag/Ag+ against an Ag/AgCl (pure) reference electrode at 600°C and a concentration of 4.1 mole pct of each chloride and came to the conclusion that complex ion formation occurred in some of the melts. Laitinen and LiUe gave an electromotive force series at 450°C for a number of {Metal/Metal ions (unit activity)) electrodes in LiC1-KC1 eutectic melt, the {pt/pt++ (unit activity)) electrode being chosen as the reference. Walker and Danly7 studied the ther-modynamic properties of NiC12 in LiC1-KC1 eutectic melt over a wide range of temperatures and concentrations by measuring the electrode potential between a nickel electrode and a chlorine electrode in the melt. Since potential measurements made by using the chlorine reference electrode are of more direct significance both in the study of electrochemical separation and in the evaluation of the thermodynamic properties of the melt, it is therefore decided to measure the electrode potentials of cells of the type {M/MCin (mole fraction = N) in LiC1-KC1 eutectic melt/Cl2 over a range of N values and temperature for a number of metal chlorides. The results should indicate the order by which the various metals plate out on the cathode and how this order is affected by temperature and the concentration of the metal chloride in the solu-

Jan 1, 1960

By J. Campbell

Various models are discussed for the evaluation of the negative pressures which may occur in solidifying materials which exhibit various deformation modes: elastic-plastic, Bingham, viscous, or creep flow. The inadequacy of the previously proposed elastic-plastic solution for solidifying metals is revealed by comparison with the more reliable creep results which are given graphically for aluminum, copper, nickel, and iron. The maximum tensions experienced in the liquid phase of solidifying spheres ranging in size from large castings to submicron powders are in the range from —10' to —105 atm for these metals. THERE has been much recent interest in the negative pressures associated with the volume change on solidification and in the possibility of the occurrence of cavitation. Considering the freezing of a highly supercooled liquid, an attempt to evaluate the stresses in the liquid ahead of the rapidly moving solidification front has been made by Horvay1 on a microscale and by Glicksman2 on a macroscale. In a casting of a wide freezing range alloy, the pressure differential due to viscous flow of residual liquid through the pasty zone has been discussed by Piwonka and Flemings,3 In a previous publication4 the author has attempted to estimate the negative pressure occurring in the residual liquid of a spherical casting, employing an elastic-plastic model to describe the collapse of the solidified shell under the internal tension. An earlier model assuming a rigid shell was shown to be inaccurate by many orders of magnitude. The elastic-plastic model is critically reviewed here, and other models are developed which are thought to be more closely related to metals and other materials near their melting points. The spherical geometry (Fig. 1) is chosen because the highest shrinkage pressures would be developed, although the analyses are readily adaptable to cylindrical geometry. A parallel sided casting experiences little internal tension because of the relatively easy dishing inward of the sides. (This commonly observed phenomenon has previously been attributed solely to atmospheric pressure.) Furthermore, small regions of confined liquid in a large solidified volume of a casting approximate reasonably well to spherical geometry. ELASTIC-PLASTIC MODEL The author has shown4 that as solidification proceeds the internal hydrostatic tension builds up until the elastic limit of the shell is exceeded. At this point the internal pressure is closely -2Y/3. Subsequently a plastic zone spreads from the inner surface toward the outer surface of the shell. When the whole casting is deforming plastically a rather more generalized analysis taking account of the externally applied pressure PA + 2y/b gives the internal pressure as: P = Pa + 2y/a + 2ys/b - 2 Y In(b/a) [1] The 2y/a and 2ys/b terms result from the tendency of the liquid-solid and solid-vapor interfaces to shrink, reducing their energy, and thereby helping to collapse the solid phase and compress the liquid phase. The 2y/b term would be important only for powders. The last term arises because of the plastic restraint of the solid, resisting collapse and so effectively expanding the residual liquid. From Eq. [I] it is easily shown that there is a minimum in the pressure at the radius amia= y/Y [2] which is of the order of 103K for the metals aluminum, copper, and iron, and corresponds to the minimum pressure Pmin = 2 Y[l-ln(bY/y [3] The results of a fully worked out elastic-plastic solution are given in a previous reporL4 The main criticism which may be leveled at this analysis when applied to metals at their melting points is the strong dependence of the yield stress on the strain rate. The strain rate varies with both solidification conditions (e.g., whether chill-cast or slowly cooled) and during solidification, as is indicated in the following section. Thus an appropriate choice of Y is very arbitrary. Before proceeding to a discussion of models which are strain-rate-dependent, it is necessary to evaluate the strain rate as a function of the rate of solidification. SOLIDIFICATION RATE Various empirical relations have been deduced5 for the rate of thickening of the solid shell by pour- out tests on partially solidified spheres. These, however, are unsatisfactory for our purposes since they become very inaccurate when the liquid core is very small. A theoretical approach is therefore necessary, and some solutions are set out below. Making the assumptions of constant surface temperature of the casting during freezing, no superheat, and a material freezing at a single temperature, Adams8 deduces the approximate solution: which becomes when b » a: Employing a semiempirical approach vallet6 finds:

Jan 1, 1969

By Donald H. McLaughlin

THE primary function of the mining engineer is to find mineral deposits and fuels in the accessible rocks of the earth and to recover them for the vast needs of our complicated civilization. On him has been placed the responsibility for the exploitation of the nation's and world's mineral resources. The degree to which the minerals of the earth have been utilized serves to an extent as a measure of man's material advancement, as well as an index of the relative strength of nations. The natural endowment of lands, varies greatly, but the intellectual energy of a people is revealed by the way in which they take advantage of their heritage of minerals or reach out to less developed regions by exporting their engineering skill as well as capital to secure the raw materials they need.

Jan 2, 1953

By Frank R. Barnako

Coal mining is a hazardous occupation, but tremendous progress has been made in reducing accidental injuries and deaths in the mines. Let us take a look at the hazards in coal mining and the accident record. COAL MINE SAFETY TODAY Underground coal mining creates underground open areas, rooms, and haulageways. The roof (top) and ribs (sides) become highly stressed, and because coal and slate are very weak in tension or compression they frequently fail and fall from the roof and ribs unexpectedly. This is the most hazardous condition miners must cope with underground, and it has consistently produced the greatest number of fatal injuries in the coal mining industry. Only very sophisticated equipment, but which is not yet practical for use underground, is able to detect the buildup of stresses that may eventually lead to a roof or rib fall. Today's miner still looks for fresh cracks in the roof or rib, listens for the "drummy" sound, and feels vibrations from loose material in the roof, when tapped with a sounding stick, in order to find material which may fall. Once located, it is barred down, but if this is not possible, it is then secured to prevent it from falling. The next great& hazard is the equipment used to mine or haul coal. It is large, heavy, reacts quickly to its controls and is operated in con- fined areas with low lighting levels. The record of the last few years shows that fatalities attributable to mining and hauling equipment are about equally divided. Thorough training as part of a complete safety program is necessary to teach employees the hazards of loose roof, rib, and machine operation in order that they can work in the safest way possible. Unless there is such a program, the trade is learned by trial and error with a resulting tragic.

Jan 1, 1973

E. E. THUM,* Salt Lake City, Utah (written discussion?).-While the present paper is confined exclusively to the microstructure of fusion welds, it may be of interest to draw attention to certain appearances existing in resistance welds such as spot or butt-welded joints produced by the Thomson process. For instance, a butt weld between two pieces of carbon tool steel (carbon about 0.90 per cent.) will show concentric ellipsoids of the various materials from pearlite to martensite. The surfaces of demarcation are quite well defined, the center of the ellipsoid being at the intersection of the axis of the piece and the plane of the weld. Often these unannealed welds show a troostitic center; evidently this core was not quenched as rapidly as the surrounding shell. Such specimens are beautiful samples for instruction purposes. An annealed butt weld of this kind will show a very well defined central ellipsoid of decarburized, materials. It is interesting to consider the reason why this change takes place. It must be understood that the heat is on the metal for a very short time, possibly 30 sec. It is therefore evident that the decarburization, or migration, of the carbon takes place with extreme rapidity. Since no blowholes are evident in a well-made butt weld, the deoxidizing air and the products of combustion must migrate with the highest speed; second, the carbon might migrate back into the stock; or, last, a large proportion of the pearlite may be extruded with the hot metal, which forms a fin at the plane of weld. Examining these possibilities in detail, it is not probable that such deep-seated decarburization, extending with maximum effect to the very center of a 2-in. round bar, is done by reaction with the oxygen of the air. This would postulate entrance of oxygen and egress of carbon oxides in large quantity without leaving behind traces in the form of oxides or

Jan 5, 1919

By E. A. Farrell

A comprehensive survey is made of the status of the asbestos industry as it relates to marketing the product. Included are descriptions of the various types of asbestos and the grading and classification systems used. The uses of asbestos, distribution practices, and types of ore bodies are all related to marketing. World production, the producers and their capacities and world consumption for 1966-67 are summarized and statistical data are included. Asbestos is a general term describing a family of fibrous minerals of the serpentine and amphibole mineral groups. Asbestos has a long history going back to the time of the Egyptians, when it was used as a lamp wick. The commercial mining of asbestos started in Canada, Russia, and Africa in the 1800's, and the first asbestos products were made in Italy and Russia. The five main types of asbestos are: chrysotile, accounting for 95% of the total mined, amosite, crocido-lite, anthophyllite, and tremolite. Canada, Russia, and Africa are the major producers of asbestos. The commercial utility of asbestos was at first based on the heat resistance of the fibrous mineral in the form of packing, at the start of the industrial revolution. Its current utility is based more on its ability to reinforce binders such as portland cement, rubber, and plastics. Its inertness to the chemical nature of most binders is unique. Most important is its ability to maintain its reinforcing utility when the product is exposed to weather and soil conditions as in asbestos cement boards and pipe, and heat, pressure, and chemical exposure as in brake linings and gaskets and packings. The mineral asbestos is also unique because its fibrous form permits it to be spun and woven to cloth or formed into paper. Many asbestos applications are critical to national defense and at the present time, there are no satisfactory substitutes. Grading and Classification Canadian chrysotile asbestos fiber is graded and priced by length since basically the longer the fiber the higher the utility. The Canadian asbestos industry does not, however, classify the fiber by direct length measurement, but by a dry screening test. The method is called the Quebec Standard Screen (QS) test. One pound of fiber is mechanically shaken in four vertically stacked sieve boxes. The relative proportions remaining on the sieves defines the grade. The longer the fiber, the larger is the amount that stays on the top coarse screens and the less on the lower, finer mesh screens. Other tests can be used to further define the length distribution of fiber such as the wet screen Bauer McNett and the Suter Webb Comb (3 group only). The Canadian grading system divides the milled fibers into 5 main groups: group 3, 4, 5, 6, and 7, with 3 group being the longest, and 7 the shortest. Each group is further divided to subgrades, identified in each group by the letters A to Z, with "A" the longest and "Z" the shortest. See Appendix 1 for the Canadian QS classification system. The Russians also use the QS test on chrysotile. The Africans classify their chrysotile into grades similar to Canadian. The African crocidolite and amosite, however, are classified into actual length groups such as l to 2 in. and 2 to 3 in. Amosite and crocidolite are generally longer than chrysotile but also more brittle. Milled asbestos is not composed of staple length fibers like fiber glass or cotton, but of a mixture or blend of fibers ranging from long to short. Milled asbestos has a fiber length distribution similar to the particle size distribution of a powder. For example, the longest group 3 chrysotile grades have a high percentage of the longest fibers (1/2 to 3/4 in.) and low percentage of short fibers (0.003 in.). The figures in Table 1 give the approximate length distribution of the longest, middle, and shortest groups. A second and further method of classifying fiber is the degree to which the fiber bundles are separated to form a larger number of smaller diameter bundles. This property is normally described as the degree of fiberization, openness or surface area. Air permeability tests are used to measure surface area. Asbestos pro-

Jan 1, 1971

By Keats, J. L.

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical charac- teristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained.

Jan 1, 1957

US 4,137,751-Aerial geophysical exploration for ore deposits by collecting and analyzing atmospheric particulates The aircraft has an Inlet duct extending outward and including a "shave-off" duct, a cyclone separator located inside the cabin which is coupled to the inlet duct, a clean air exhaust duct, and a receiver for the collected particles incoming air is divided into two fractions. The fraction taken by the "shave-off" duct and containing the bulk of the particles is routed to the cyclone Particulates are gathered on a collector tape for subsequent analysis and correlation with the areas covered J. R Rhodes, R D. Sieberg, M. C Taylor, J. C Westkaemper, and R C. Young, assigned to Columbia Scientific Industries, Inc Feb. 6, 1979 7 pp. (73-28) Filed- 2-28-75 (554,114) Same British 1,446,760, dated Aug. 18, 1976. US 4,156,138-Exploration for subsurface deposits of uranium ore Pairs of dosimeters are placed underground in a grid pattern Each dosimeter contains a phosphor which IS capable of storing the energy of alpha particles. One dosimeter is heavily shielded from alpha particles, while the other in the pair is thinly shielded to exclude dust After a period underground the dosimeters are heated to release the stored energy as light. The amount of light produced from the heavily shielded dosimeter is subtracted from the amount of light produced from the thinly shielded dosimeter to give an indication of the location and quantity of uranium underground This patent is a division of US Patent No 4,053,772, dated Oct 11, 1977 P E Felice, assigned to Westinghouse Electric Corp May 22, 1979 5 pp (250-253) Filed. 8-12-77 (824,203) US 4,180,727-Method for measuring the gamma-gamma density of uranium ore in the vicinity of a borehole A first gamma-ray detector receives only natural gamma rays from the borehole, while a second receives both natural gamma rays and scattered uranium-source gamma rays The value of the uranium-source gamma rays is calculated. W W Givens, assigned to Mob11 011 Corp Dec 25, 1979 6 pp (250- 264) Filed 10-20-77 (843,909) US 4,180,72&A neutron activation probe for determining the location and grade of uranium ore, especially where thorium or other fissionable isotopes are present, includes a pulsed neutron source in series with a plurality of delayed neutron reactors for measuring radioactivity in a well bore- hole together with a Nal(T1) counter for measuring the high energy 2 62 MeV gamma line from thorium The signal from the Nal(T1) counter IS subtracted from the signal from the delayed source detectors to ascertain the amount of uranium present in the ore body N. P Goldstein and R C Smith, assigned to Westinghouse Electric Corp Dec 25,1979 6 pp (250-264) Filed. 4-1 1-78 (895,323)

Jan 1, 1980

By J. A. Morgan, R. E. Lund, D. E. Warnes

The design, operation, and performance of an integrated pilot plant for recovering zinc and copper from a complex sulfide ore are described. Metallurqical processing comprised selective sulfate roasting in a fluid bed, leaching in a weak sulfuric acid solution, recovering copper by cementation with scrap iron, air oxidation to remove soluble iron, more-or-less conventional Purification for removal of impurities deleterious to zinc electrolysis, recovering zinc by electrolyzing solutions, and recycling spent electrolyte to the sulfating roaster. The effects of several feed preparation and roasting variables on the sulfation response of zinc, copper, and iron are set forth, together with the electrolyzing characteristics of the zinc solutions. SEVERAL years ago, St. Joseph Lead Co. undertook a research program to develop procedures for winning values from a complex ore. The deposit was a massive sulfide ore body containing upwards of 65 pct pyrite. Gangue, composed principally of quartz, calcite, dolomite, and alumina, comprised only 10 to 20 pct of the mineralized zones. Zinc, lead, and copper values were variable, but averaged about 6.7 pct Zn, 2.6 pct Pb, and 0.4 pct Cu. Early in the exploratory test work, it was established that the intimate physical association of the minerals in the ore made beneficiation by conventional flotation procedures difficult. Accordingly, in addition to a comprehensive program to investigate physical methods of ore beneficiation, a research program was established to develop a direct metallurgical method for processing the ore. After surveying a number of potential methods for recovery of both metal and sulfur values, effort was concentrated on the development of a sulfate roasting process. It is the pilot-plant development of the sulfate roasting-solution purification—electrolyzing procedures which forms the subject of the present paper. PREPILOT PLANT INVESTIGATIONS From a thermodynamic viewpoint, it is feasible to sulfate selectively a host of metals, including Zn, Cu, Pb, Cd, Ni, and Co, in an iron sulfide ore without sulfating iron. Of course, a number of conditions such as roasting temperature and gas composition must be controlled. In addition, as first disclosed by Hybinette,' an alkali metal salt is frequently beneficial in promoting the sulfation reactions. The application of fluid bed roasting to the sulfate roasting of nonferrous metals was pioneered by Stephens of Battelle Memorial Institute.' Subsequently, Falconbridge Nickel Mines, Ltd. developed an unique process for selectively sulfating and recovering nickel, copper, and cobalt from their nickeliferous pyrrhotite, which recently has been described in an excellent paper by Thornhill.3 One of the unique features of the Falconbridge process is that the feed is introduced into the fluidized roasting furnace in a manner such that the feed slurry is broken up into droplets and the droplets lose their moisture before contacting the surface of the fluidized bed. The dried droplets do not tend to cake or fuse, but rather remain as discrete agglomerates of concentrate particles and roast without significant degradation. St. Joseph, aware that Battelle Memorial Institute had participated in the development of the Falconbridge process, obtained permission from Falcon-

Jan 1, 1962

By Carl Samans

THE attention of physicists and metallurgists has been directed toward the study and explanation of the deformation textures in metals for the past 15 years. In 1920 N. Uspenski and S. Konobejewski1 were first able to show that the symmetrical X-ray diffraction effects that had been previously reported by E. Hupka2 and others in metal foils were caused by a directed arrangement of the crystallites. Since then, the systematic study of textures resulting from the application of the pure forces of tension or compression to polycrystalline materials hag been supple-mented by many investigations on deformed single crystals, which have greatly added to our knowledge of deformation. However, despite the valuable information secured from these comparative studies only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature. This lack of quantita-tive data is especially unfortunate because of the much greater practical significance of rolling textures and their effects in both cold-rolled and annealed materials. This investigation was undertaken for the purpose of specifying the deformation of rolled single crystals in the hope that such information might later facilitate the explanation of polycrystal-line textures.

Jan 1, 1934

By C. M. Schwartz, A. E. Austin, W. B. Wilson

High-temperature X-ray diffraction studies were conducted with Th-U alloys with up to 10 wt pet U. The solid solubility of uranium in thorium as a function of temperature was determined by the method of lattice parameters. Thorium will dissolve up to 2.5 wt pet U at 950°, 4.5 wt pet U at 1150°, and 7.5 wt pet U at 1250°C. Determinations were made of the temperature of the transition of thorium and of the effect of uranium upon the transition. The a to ß transition for thorium was observed to occur at 1330' ±20°C. Mean coefficients of expansion were calculated for thorium and two alloys, and for ThO2 in contact with the thorium, using X-ray lattice-parameter data. Values obtained at 950° C for thorium and Tho2 were 12.1 and 9.40 X 10-6 per OC, respectively. Impurities obtained during the X-ray exposure were identified by diffraction and were essentially Tho2 and ThC, with two additional unknown phases being detected. The effect of the impurities upon the results is discussed. DIRECT investigation (i.e., high-temperature X-ray diffraction studies) of the phase diagram of thorium-rich uranium alloys has been shown to be necessary since recent work1 - has disclosed the presence of an allotropic transformation near 1400°C in pure thorium with the room temperature face-centered-cubic phase transforming to a body-cen-tered-cubic structure at the elevated temperature. The effect upon the transition of the addition of uranium to thorium and of the solubility of uranium in thorium at high temperatures remained unknown, yet was of interest in understanding fabrication procedures and elevated temperature use. The present work was undertaken to provide information in this area by determining the transition temperature, the effect of uranium on the transition temperature, and the solubility of uranium in thorium as a function of temperature. Experimental Work The high-temperature diffraction data were obtained using a camera especially designed for the purpose3 and capable of reaching temperatures in excess of 2000°C at pressures as low as 1 x 10." mm Hg. Temperature regulation was provided by regulating the power input to ±0.1 pet variation, and by regulating the water flow through the camera jacket to provide a constant thermal load. The X-ray sample was a rod nominally 80 mil diam, which was further turned down to 20 mil and then etched to 18 mil over 1/2 in. of one end. This was placed in the sample holder and mounted on the camera so that the smaller part was surrounded by a cylindrical tantalum-sheet radiation-type heating element. Diffraction from the sample was recorded on film after passing through a slot in the heating element and radiation-baffle shield and through beryllium vacuum windows. The X-ray film mounting was of the Straumanis type4 with a camera diameter of 114.59 mm. Since previous work of Chiotti' indicated that impurities considerably alter the transition temperature, chemical analysis of the arc melted iodide crystal-bar thorium samples was obtained prior to testing. The analysis disclosed the material to contain as low as 0.001 ±0,0002 wt pet H and 0.007 ±0.001 wt pet 0. Carbon was 0.003 wt pet and nitrogen less than 0.002 wt pet. This material was sealed in mild steel in an inert atmosphere and subsequently hot rolled to 3/8-in. diam rods at a temperature of 732°C. Following removal of the jacket, the material was pickled and cold swaged to 1/8-in. rods, from which the diffraction samples were prepared. The alloys were similarly prepared, with the uranium being added during arc melting. The uranium analyses of the alloys prepared appear in Table I. The experimental procedure for diffraction examination of the three samples of high-purity thorium differed from those of the Th-U alloys. The original practice, later modified, consisted of pumping down the camera with the diffusion pump on and then admitting liquid nitrogen to the cold trap of the system. This was modified for the Th-U alloys by maintaining liquid nitrogen in the cold trap at all times before and while the diffusion pump was heated. This minor change produced a reduction in the amount of carbon pickup by the sample during exposure to the diffusion-pump vapors. The sample was brought to the desired test temperature and exposed for 21/2 hr at pressures which were usually 2 x 10-6 mm Hg, or lower. Exposures were made at

Jan 1, 1959

By A. R. Kaufman, P. Gordon

THE large-scale manufacture and use of uranium in conjunction with the atomic energy development during the war led to a need for knowing the equilibrium diagrams of uranium with various other metals. The alloys of uranium with aluminum and with iron were among the first that were studied for this purpose. Much of the work was done in the manner of a survey since it was necessary to determine the important features of the phase diagrams rather than to obtain completely detailed results. For this reason no attempt was made to locate exactly such features as liquidus lines, solid solubility limits and compound and eutectic compositions. It is believed, however, that there are no great inaccuracies in the diagrams reported here and that no important points were overlooked. Earlier work on alloys of uranium with aluminum and iron is almost nonexistent and in each case is considered to have been of little value by M. Hansen. It is interesting to note, however, that the compound UAl3 was first reported in 1902 by L. Guillet. Experimental Procedure Materials: The uranium used for making most of the aluminum alloys was obtained from material prepared by Metal Hydrides, Inc., and melted in vacuum at M.I.T. Because of the lack of an adequate supply of metal, it was necessary to use material from several different batches and hence it is impossible to state an exact analysis. However, a few results indicated about 0.01 to 0.03 pct iron and probably about 0.03 to 0.05 pct carbon. Toward the end of the work a small amount of metal was obtained from Brown University and from Iowa State College and this was used in determining the transformations in pure metal and in some dilute alloys. All of the aluminum used in this investigation came from a supply of high purity metal (greater than 99.9 pct aluminum) which was obtained through the courtesy of Dr. Mehl of the Carnegie Institute of Technology. The uranium used for making the alloys with iron was produced by the bomb reduction process which has been described by J. Chipman.² This metal, after vacuum melting, contained about 99.9 pct uranium by weight with carbon and iron as the chief impurities. Electrolytic iron containing about 0.012 pct carbon, 0.020 pct nickel and 0.009 pct copper was used in making the melts. Melting Equipment: The melting of the alloys went through a stage of development which culminated in the use of beryllia or beryllia-lined crucibles and in the use of high frequency heating in either vacuum or in an atmosphere of argon. It was found that uranium at a few hundred degrees above its melting point would pick up aluminum and to a lesser extent silicon from an alundum thimble while aluminum above 1000°C would extract silicon from the impure alundum. No reaction of either metal with beryllia was noted at temperatures as high as 1800°C. The distillation of aluminum from the aluminum-rich alloys was quite troublesome at temperatures above about 1300°C and was only partially avoided by the use of argon instead of vacuum. Melting in resistance furnaces,

Jan 1, 1951

By Frederick N. Rhines, Robert F. Mehl

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ‡ in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Zedele and of Zedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938