Search Documents

By W. J. Rogers, L. J. Dwiggins, R. O. Williams

THERE has been comparatively little work on the importance of strain rate and temperature as variables in the formation of deformation textures. For this reason the present work was started, the choice of compression being in part that of convenience and in part because of the absence of quantitative data in this area. These do not turn out to be important variables within the range studied which permits the results to be condensed into this note. Samples 1/4 in. in diam and 1/2 in. long were machined from 99.9 pct pure commercial aluminum and recrystallized to a fine grain size. A set of five samples were deformed between a spring-driven weight and an anvil resulting in roughly 20 pct strain each time. The strain rate varied because of decle-ration and shortening of the sample but would average about 10&apos; per min. Deformation at temperatures over the range of -76" to 150°C were obtained by heating or cooling the samples. Complete lubrication could be obtained by oil since the short time of contact did not permit its escape. The samples were compressed to a total true strain of 1.4 to 1.6. A larger sample was prepared similarly with spiral grooves in the ends to hold paraffin which provided essentially complete lubrication. This sam ple was compressed slowly at room temperature at a rate of about 2 per min to a total strain of 1.0. Cylindrical samples were carefully machined from these discs with a radial direction as an axis. They came from the center half of the samples and were roughly 1/16 in. in diam. The samples were etched down 15 pct to remove any surface effects. Diffraction data were then obtained for six different kinds of planes by the use of the Norton technique as applied to a fiber texture. Direct comparison between the raw data failed to reveal any significant difference between any of the samples and consequently the data from only one sample was completely reduced. The particular sample had been deformed at O°C The background was subtracted from the intensity data which were averaged over the four quadrants and then normalized to random. These data were then used to obtain fiber-axis distribution charts as previously described.2 For this sample the (422) plane was also run to assist in this inversion. The final result, Fig. 1, provided a comparable fit to that previously obtained from fiber data. About 85 pct of the material forms an elliptical texture around the <110> direction. The radius (at half height) is 5.5 deg along the (111) boundary and 8 deg along the (100) boundary. The remaining 15 pct forms a ridge running from this texture to near the <311> direction. The regions around the (100) and (111) planes are devoid of material. The earlier qualitative results of ~arrett~ are in complete agreement with the present results. The possibility has been dis-cused that the material around the <311> results from friction between the sample and compression plates.4 The present results are considered proof that such is not the case because of the uniformity of sample deformation and the requirement of axial symmetry before fiber-axis distribution charts can be accurately obtained. Recently results have been obtained to show that strain rate and temperature are important variables in the extrusion of aluminum.5 Perhaps the most important observation was that the partial recrystal-lization occurred even at room temperature. Strain rate was considered to be a factor only in that it produced a temperature change. There are many differences between the two experiments, the most important possibly being that their material was roughly ten times the purity of the present material. The present experiment, however, may not be as definitive as desired in this respect since it has been shown that compressed aluminum recrystallizes without a texture change6 although supplementary

Jan 1, 1961

By W. M. Reilly, Martin E. True, O&apos

A technique, equipment, and a compound have been developed and field tested for sealing tubing joint thread leaks without removing the tubing from the well. This eliminates the necessity of killing the well with possible damage to the producing formation, which could result if it were exposed to drilling mud. A thread sealing compound, developed and tested in the laboratory, is introduced into the tubing and squeezed into the joint to eliminate the leak. A high percentage of successful field applications have eflected an appreciable cost reduction in repairing leaking tubing strings in East Texas and in the Louisiana Gulf Coast area. INTRODUCTION In producing oil and gas wells the industry has been plagued with a never ending problem of tubing connection leakage. This situation is becoming increasingly more significant as more gas wells are placed on production and as higher pressures are encountered at greater depths of current drilling. Substantial progress has been made in minimizing thread leaks by careful handling and cleaning of joints and by the use of improved sealing compounds in combination with controlled makeup. But even with the use of the best known methods and sealing materials during initial makeup, occasional leaks through tubing joint threads appear inevitable. In some instances, tubing joints in high-pressure gas wells have been found to leak gas at relatively less pressure than that at which the tubing had been tested satisfactorily using liquid. Many expedients have been employed to prevent the physical replacement of tubing when leaks have developed. Perhaps the most commonly used is the sodium silicate treatment in which the solution is lubricated into the tubing to form a crystalline plug in the leak. Generally, any benefit realized is of a temporary nature. In addition to field studies on handling and makeup of tubing, extensive laboratory work has been undertaken on the development and testing of thread dopes.&apos; Also, substantial effort has been devoted to testing tubing joints using high-pressure gas as a pressure medium.&apos; The results of this work have emphasized that tubing joints are susceptible to occasional leaks, especially when subjected to relatively high differential pressures. To cope with the problem of leaking connections, an extensive investigation was undertaken to devise means of sealing leaks without removing the tubing from the well and without reducing the inside diameter of the tubing. The purpose of this paper is to present a technique, together with the associated equipment and compound, which have been developed for effecting a seal of leaking tubing in place. DISCUSSION Work was initiated simultaneously on two ventures: (1) to develop a satisfactory leak sealing compound and (2) to develop tools necessary to find the leak and place the compound. Leak Sealing Compound In the development of a sealing compound, tests were conducted on those compounds commercially available which include: (1) conventional thread lubricants, (2) thermo-setting resins and (3) other materials which held promise of effecting a seal. Although none proved completely satisfactory in their available form, two commercial compounds proved nearly equally effective in sealing leaks during laboratory tests after proportioned quantities of graded silica had been added. Field usage has indicated that the preferred compound is one prepared of an aluminum-stearate base thinned to the proper constituency and carrying a mixture of fine mesh graphite and graded silica. The compound developed by Humble Oil & Refining Co. is designated as Tubing Thread Leak Sealant 800. Placement Tools and Technique In developing tools to detect joint leaks and to place the sealing compound, work was done initially on wireline equipment. Preliminary designs were completed of a tool somewhat on the order of a pressure bomb to test individual joints with gas at high pressure to determine if the joint was leaking. An entirely different tool equipped with opposed packers was intended for placement of the sealing compound at high pressures in each leaking joint. The application of these tools

Jan 1, 1958

By F. R. Cattoir, R. W. Kimball, C. T. Anderson

ONE of the principal impurities in all steels is sulphur. Sulphur-bearing, manganese-free steels exhibit hot shortness. Manganese is added to steel to improve the hot-working properties. If no sulphur were present in steel, it is probable that hot shortness would be nonexistent. This paper is the first of a series to be issued by this Laboratory reporting the measurements of hot forgeability tests and the physical properties of Fe-C alloys to which additions of various alloying elements have been made. The present paper describes the results- obtained by the addition of varying amounts of sulphur to Fe-C alloys. To obtain control over residual elements in the various charges melted in the arc furnace, it was considered advantageous to use sponge iron from one source as the melting stock rather than scrap metal having an unknown history. Small amounts of unwanted alloying elements might be introduced into the charge when scrap was used, thereby influencing the results of the various heats. A sponge iron having a high silica-lime ratio was used. Ore from Sunrise, Wyo., had been reduced to sponge iron and briquetted at the Bureau of Mines sponge-iron plant at Laramie, Wyo. The briquettes were 5 in. in diam and 2 to 3 in. in thickness, and weighed about 10 lb each. The chemical analysis of the sponge iron is as follows: C, 0.67 pct; Mn, 0.10; SiO2, 4.75; CaO, 1.4; P, 0.044; S, 0.72; MgO, 0.4; A12O3, 1.1; total Fe, 87.5; Fe metallic, 79.2; and reduction, 90.5 pct. Where a reducing agent was required, crushed graphite electrodes usually were used. The charcoal available contained 0.20 pct S. An analysis of the available coke showed it to contain 0.70 pct S. Where high sulphur heats were required, elemental sulphur additions were made to the ladle. Limestone of good quality was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2, 3.0; and P2O5, 0.014. Melting Procedure Sponge iron was melted to produce metal stock for the experimental alloys in a silica-lined, three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating. Fig. 1 shows this furnace installation. About 25 tons of sponge iron was melted in 75 heats, averaging 927 lb of sponge iron to the heat. An addition of carbon was required to complete the reduction of a portion of the iron oxide remaining in the sponge to prevent high losses of iron oxide in the slag and a low carbon content in the resulting metal. As reducing agents in preparing the melting stock, charcoal, coke, and a carbon product resulting from the thermal decomposition of natural gas were used. The quantity varied from 20 to 60 Ib per furnace charge, with an average of 38 lb. An average analysis of the metal obtained gave 0.52 pct C, about 0.01 pct Mn, 0.070 pct P, and 0.092 pct S. The average yield of metal was 647 lb with 241 1b of slag, the sponge-iron recovery being 70 pct. The metal obtained in melting the sponge iron was cast into pigs weighing about 20 lb each to facilitate recharging into the furnace for further refining. The pouring of the pigs is shown in Fig. 2. The average power consumption for the production of the 24 tons of metal obtained was 1704 kw-hr per ton.

Jan 1, 1954

ONE of the largest hard rock operations ever undertaken on the continent is part of the Aluminum Co. of Canada&apos;s gigantic British Columbia development in the mountainous wilderness back of the north coastal port of Prince Rupert. To provide electric power for the huge aluminum smelter under construction at Kitimat, 400 miles northwest of Vancouver, Alcan is reversing the flow of a 5000 sq mile drainage area by blocking the eastward-flowing Nechako River with the largest sloping clay core dam in the world. The backed-up waters of a 110-mile chain of lakes will be tapped at their eastern end by a 10-mile tunnel piercing a mile-high mountain range. From this tunnel water will pass through penstocks to a subterranean powerhouse after a drop of 2600 ft and empty into the Kemano River almost at tide water. A projected battery of eight turbine-driven generators will produce more than a million horsepower, although, initially, three generators of 140,000 hp each will be installed. Power will travel 50 miles across another mountain range, over a glacier, and across an arm of the ocean to what will ultimately be the world&apos;s largest aluminum smelter-a plant 2 ½ miles long. Ore smelted at Kitimat will come from Jamaica, but carving the tunnel, penstocks, and powerhouses cavern out of the heart of a mountain is so vast a job that most of the problems of a major mining operation are encountered. The powerhouse cavern alone is a big hard rock job. This chamber lies 1400 ft back from the mountain face and will eventually be 1100 ft long, 80 ft wide, and an average 118 ft high. Now under construction, the roof of this cavern will take the form of a parabolic arch. The prime contractors, Morrison-Knudsen Co. of Canada, are to excavate a length of 700 ft by May 1954. This section will provide a main control room, erection bay and space for eight generating units. The roof arch is to be lined with reinforced concrete and a plan now under study provides for concrete curtain walls separated from the rock sides of the cavern to prevent moisture accumulation. Cavern Excavation Excavation of the cavern began with the driving of an 8x8-ft exploratory drift 1500 ft long. Two horseshoe-shaped access and tailrace tunnels were bored to serve excavation work. These tunnels are approximately the same length as the exploratory drift and 25 ft high. The floors of both tunnels were graveled to permit the use of rubber-tired equipment. Eventually, the tailrace tunnel will be enlarged to 40 ft height to drain water from the turbine pits below the powerhouse floor. When the tunnels reached the cavern location, a mucking tunnel, approximately 25 ft square, was driven the projected length of the powerhouse at the floor level of the cavern. Another tunnel, 10 ft square, was carried in the same direction from the exploratory drift at the level of the arch spring line, 65 ft above the cavern floor. To connect these two tunnels, seven shafts 10 ft wide and approximately 80 ft long were driven through to the lower mucking tunnel, 65 ft below. These shafts were located on 120-ft centers, the length of the powerhouse cavern. Blasting is done from this upper tunnel to the final line of the roof arch. Two bulldozers, an International TD-24 and a TD-9, doze blasted material to the shafts where it drops to floor level. From here, the rock is loaded by Eimco loaders and power shovels into rubber-tired Koehring Dumptors and Euclid end-dump trucks. The arched roof section will be completely excavated and concreted before vertical blast holes are drilled down from the level of the arch spring line to the floor of the cavern. The arched roof section with its parabolic curve will have a width of 80 ft and a rise to the crown of 47 ft.

Jan 1, 1952

By A. L. Barnes

A number of reservoirs have been partially invaded by bottom water. Water flooding such reservoirs can be especially inefficient if the oil has a high viscosity because injected water will under-run the oil and emerge at producing wells without having displaced much oil. A possible means of improving water sweep efficiency would be to precede the water flood with a slug of water purposely thickened with a chemical additive. This possibility has been studied with a scaled laboratory flow model. The investigation was carried out on a model representing a 20-acre five-spot with one set of reservoir condition~. Displacements were performed with water, with viscous-water slugs of 10 and 25 per cent of the pore volume followed by water, and with all viscous water. Displacement tests were made at several rates of injection. For all cases, compared at the same producing water-oil ratio, an increase in rate resulted in an increase in volumetric sweep. The larger the quantity of viscous slug injected, the greater the crossflow of oil ahead of the displacing front and, thus, the lower the WOR during that period of a displacement. This investigation indicates that the injection of aqueous viscous slugs in this type of system would give some additional benefit over conventional flooding by (I) reducing the life of the flood, (2) reducing lifting costs and (3) increasing ultimate recovery. The benefits of a viscous-slug displacement would warrant its use if the viscous water could be created for a few cents per barrel. INTRODUCTION The most appropriate method for water flooding oil reservoirs which have been partially invaded by bottom water has been a problem of considerable interest. Such reservoirs, having good vertical permeability and unfavorable mobility ratios, are difficult to produce efficiently under normal waterflood procedures. Even though the injection wells have been plugged back above the oil-water contact and the water zone has been squeezed off, injection water will enter the formation and not only displace oil, but also much of it will displace the bottom water, thus creating a high producing water-oil ratio at the start of a flood (see Fig. 1). Since the rate of injection and the viscosity of the displacing fluid are the more easily controlled physical parameters of the reservoir, it is quite natural to study their effects on the volumetric sweep of the oil zone and on the producing water-oil ratio. Increasing the viscosity of the displacing fluid has two disadvantages—it reduces the maximum rate of injection into the reservoir, and it costs more than water. It was thought that the injection of a viscous-fluid slug, followed by water, would minimize these two disadvantages, increase the volumetric sweep of the oil zone and reduce the producing water-oil ratio. Water with an additive to increase viscosity would probably be the most effective. The primary purpose of this investigation was to determine the feasibility of injecting viscous-water slugs followed by water to improve or hasten oil recovery while reducing the producing water-oil ratios. The effect of injection rate upon recovery was also investigated. A laboratory model, scaled to a 20-acre five-spot prototype with one set of reservoir conditions, was constructed. Laboratory studies of displacements with (1) water, (2) viscous-water slugs of 10 and 25 per cent of the pore volume followed by water and (3) all viscous water were performed at several rates of injection. THEORY OF SAND MODEL SCALING There are two conventional means of determining scaling criteria. These are dimensional analysis and inspec-tional analysis. Determining scaling criteria by dimensional

By W. O. Brown

A laboratory investigation was conducted to determine quantitatively the extent to which connate water was contacted and displaced by invading flood water. In these experiments the connate water in unconsoli-dated sand packed columns was completely displaced by injecting water. The nature of this displacement was similar to that previously described for single-phase miscible fluid displacement studies, and thus the presence of a non-wetting immiscible phase did not appreciably change the nature of the displacement. The effects of water injection rate, column length, and oil viscosity on connate water displacement were investi-gated. It is concluded that the connate water in a reservoir is the water which actually displaces oil from the pores of the rock during a water flood. During a water flood the connate water forms a zone which separates the invading flood water from the continuous oil phase. The size and shape of connate water bank is chiefly dependent oil the oil viscosity and the column length. INTRODUCTION Water flooding is one of the most widely used techniques for the secondary recovery of oil. Presently, however, it is still not possible to recover all the oil in a reservoir by water flooding. The research described in this paper was conducted as part of a study to determine the conditions under which 100 per cent oil recovery could be attained by water flooding. The particular objective of this work was to determine if any chemical agent, regardless of its nature, placed in the flood water could be effective in influencing the mechanism of displacement of the oil by water. It has been known for many years that water does not displace all the oil in a reservoir because a portion of the oil is "trapped" and held immobile by capillary forces. This oil is trapped within the pores of a water-wet rock when it becomes broken into discontinuous globules. Initially, when oil is present at high saturations within the pores of a water-wet rock, the connate water forms rings around the points of contact of the sand grains and may even completely fill small cavities between grains, whereas the oil occupies the larger void spaces between the grains.&apos; Under these conditions, the oil in these spaces is in the form of irregular but continuous filaments, the diameters of which depend on the geometry of the sand pores. The filaments are formed by the oil contained in the small cells which are formed between the sand grains and are connected to their neighboring cells by channels or tunnels formed by pendular rings of water. At a high oil saturation, the oil filaments conform approximately to the shape and size of the cells and their connecting tunnels. Starting with this distribution, as the water saturation is increased the water layers in the small cavities and on the surface of the grains grow. As this occurs, the water rings grow and the diameters of the oil filaments decrease. When an oil filament is reduced to a critically small diameter, the filament breaks, and its tunnel fills completely with water. Any oil which remains within a cell after all its connecting tunnels have been water-filled is trapped as a discontinuous globule. Once the oil has become trapped, the capillary forces oppose distortion of the globules and may prevent their being squeezed through the water-filled tunnels. Only a very small pressure gradient is sufficient to keep oil moving as a continuous filament. On the other hand, once the filament has broken into discontinuous oil droplets a relatively large force is required to distort the surface of a drop and move it through a water-

Jan 1, 1958

By Robert Bell

The regions to which this paper refers include the whole of the Dominion of Canada east of the 130 Rocky Mountains and north of the water-shed of the St. Lawrence. Very little exploration for economic minerals has yet been done in this immense country; but that little has already served to indicate great wealth in some localities. Having been engaged for a number of years in conducting government geological explorations in these vast territories, I shall endeavor to give the members of the Institute an idea of the prospective mineral resources of almost half a continent, as far as they are yet discernible. I purpose confining my observations to the economic minerals, and will not attempt a description of the geology of these territories; hut it will be necessary to say a few words about the rocks in order the better to explain the distribution of such minerals. The Laurentian nucleus of the continent is the principal feature of the geological map of the Dominion. It stretches from Lake Superior to Baffin&apos;s Bay, and from Great Bear Lake to the Straits of Belle Isle. Hudson&apos;s Bay itself, which is half the size of the Mediterranean Sea of the old world, lies in the center of this area. Its shores are bordered in places with newer rocks. On the west side of James&apos; Bay (its southern prololigation) these extend inland over 200 miles, and consist of fossiliferous Devonian and Silurian strata. On the western and northwestern side of Hudson&apos;s Bay proper, altered rocks are met with, some of which resemble the gold-bearing strata of Nora Scotia, some the Huronian of Lake Huron, some the older Huronian, and others the crystalline series of the neighborhood of Sherbrooke in the Province of Quebec. Along the east coast (called the Eastmain)and among the islands lying off it, there is an interesting set of volcanic and sedimentary rocks which appears to be identical with the Animikie and the Nipigon series of Lake Superior. The area which I have characterized in a general way as Laurentian, includes tracts and belts, more or less extensive, of the Huronian series. Such areas appear to be most common, and have been best explored, in the country between the Great Lakes and Hudson&apos;s Bay.

Jan 1, 1886

By E. S. Shaw

Utah continues as a very unimportant factor in oil and gas production. During the year 1933 there were no developments of noteworthy significance. There were no completions of either producers or dry holes during the year. The only commercial production in Utah has been from the five fields listed in Table 1 and mentioned briefly in the following paragraphs. Virgin Field.—Oil was first discovered in 1907 in a well drilled in sec. 13, T.41S., R.12W. Of the first 15 wells drilled, all but three were failures. In 1920 production from four wells from 550 to 600 ft. deep was about 20 bbl. per day. San Juan Field.—The majority of drilling in this area was done during the years 1908 to 1911. Probably the first commercial well in the field was that drilled in NW.$i sec. 6, T.42S1 R.l9E., in 1909. Farnham Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1923. A number of years later a second well was drilled by The Carbon Dioxice a mica1 Co., the present operator, which markets the gas in the manufacture of "dry ice" and allied products. The eslimated production, as indicated in Table 1, includes 500 million cubic feet estimated to have been lost while drilling the discovery well. Cisco Dome.—The discovery well was drilled by The Utah Oil Refining Co. in November, 1924. The Crystal Carbon Co. markets the gas in the manufacture of carbon black. Ashley Valley Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1925. The Uintah Gas Co. markets the gas in Vernal, Utah, for fuel. Woodside Structure.—In February, 1924, gas was discovered in a well drilled by Utah Oil Refining Co. in sec. 12, T.l9S., R.l3N., on the Woodside structure. This gas is reported to contain an appreciable amount of helium. It is being held as a helium reserve by the United States Government. Salt Valley Structure.—The test of the Utah Southern Oil Co. in sec. 31, T.23S., R.21E., on the Salt Valley structure has been shut down for some time at 6120 ft. This test has passed through more than 5000 ft.

Jan 1, 1934

By V. R. Garfias, A. C. Fernandez

Despite artificial curtailment in all the fields of Mexico during 1937, owing to strikes and other disturbances, the production of crude petroleum aggregated approximately 46,738,000 bbl., showing a substantial increase of about 5,571,000 bbl. over the preceding year. Most of this increase occurred in the Poza Rica area, where, although only two wells were completed during the year, production increased from 14,162,000 bbl. in 1936 to 18,634,000 in 1937. While production in the South fields (Golden Lane) remained practically stationary, the output in the heavy-oil district of the Northern fields showed an increase of 1,930,000 bbl., because production had been considerably curtailed during 1936. Production in the Isthmus of Tehuantepec decreased about 596,000 bbl., owing to labor disturbances. Crude run to stills in local refineries increased from 34,000,000 bbl. in 1936 to 36,650,000 in 1937. Exports of crude and refined products were approximately 22,700,000 bbl., or 500,000 bbl. less than in 1936. Domestic consumption, excluding ships bunkers, reached a total of 20,000,000 bbl., which shows a small increase of 200,000 bbl. over the. previous year. Domestic demand for gasoline is estimated at 3,400,000 bbl. for the year, which represents an increase of 500,000 bbl. over 1936. In all, 60 wells were completed in Mexico during 1937, as compared to 70 in 1936 and 74 in 1935. In proven areas 52 completions resulted in 25 producers and 27 failures. In the Northeastern area near the United States border, five gas wells were drilled, all of which were producers; one of them, in Camargo, came in with a daily production of 20,000,000 cu. ft. of gas. One well, resulting in a failure, was drilled in Las Uvas, Coahuila, and three wells were completed in Quebrache, to the southeast of the heavy-oil district, resulting in two small producers and one failure. TWO more wells drilled in San SebastiBn, east of the Golden Lane, were failures. Fields Northern Fields (Heavy-oil District).—A total of 11 producers and 22 failures was completed in the proven areas of the Northern fields, as compared to 16 producers and 25 failures in 1936. In the Altamira

Jan 1, 1938

H. M. BOYLSTON, Cambridge, Mass.-I would first like to ask what machine Capt. Bellis used to make his tests on impact strength. I have made some tests with the Charpy impact machine, the specimen being supported at both ends and nicked in the middle, and, find that the results do not always agree with those obtained by the Izod and other machines. I would also like to ask what effect the composition and heat treatment of the tool steel had on the drilling of his rifle barrels, as compared, with the heat treatment of the steel itself? I notice that the analysis of the composition of steel used shows sulphur 0.050 and phosphorus 0.065; I should like to ask how those high limits of sulphur and phosphorus came to be allowed? I have some data which lead me to feel pretty certain that those high limits make for very unsafe steel in rifle barrels. It has never been explained to the satisfaction of all of us, why the manganese is so high: 1.22 per cent. I believe several reasons have been stated; among them, that it is high in order to compensate for the high sulphur, and also to increase the elastic limit and improve other physical properties of steel. Lastly, I wish to ask whether Capt. Bellis has tried any different methods of heat-treating his steel rifle barrels? Apparently these were all heat-treated before machining; has he had any experience with heat-treatment after machining, especially after drilling? Those questions may seem somewhat outside of the range of this -paper, but they are important, and if Captain Bellis can give us any information, it will be very helpful. Dr. J. A. MATHEWS,* Syracuse, N. Y.-The same subject was discussed here last year, and the earlier papers by Dr. Carle Hayward seem to indicate that nothing was gained by the length of time of &apos;tempering. (It should be borne in mind that his results were based upon electrical and magnetic measurements and not upon tensile tests.) That idea has been accepted as gospel by steel workers, until late years, and particu-larly in connection with alloy steels, on which there is no question that the effect of time of tempering is very marked.

Jan 4, 1918

By G. C. Gester

Oil has been produced in Persia and India for many years, but it was not until 1932 that Arabia entered the arena as a potential oil-producing area. In 1930 the Standard Oil Co. of California acquired a concession covering the rights of exploration and exploitation for oil in the Bahrein Islands and in June, 1932, the first commercial production was discovered by the bringing in of a well known as Jebel Dukhan No. 1 on the Island of Bahrein. Since then the Standard Oil Co. of California through its wholly owned subsidiary, The Bahrein Petroleum Co. Ltd., has been carrying on a systematic survey and development program of its concession in the Bahrein Islands. This group of islands, of which Bahrein is the largest, is in the southwestern portion of the Persian Gulf, approximately 25 miles from the mainland of Arabia. Although geographically a part of Arabia, the islands are not a part of the Kingdom of Saudi Arabia. Their government is essentially independent but certain special rights have been granted to Great Britain through a series of treaties. The Island of Bahrein is 32 miles long by 9 1/2 miles wide and covers an area of 215 square miles. Approximately three-fourths of the island is occupied by a relatively low, broad, elliptically shaped dissected hill, the central part of which is slightly depressed with inward-facing cliffs but culminating in the Jebel Dukhan (Hill of Smoke), which rises to an elevation of 443 ft. above sea level. The topography of the island is a good index of its geologic structure. Structurally the island is an elongated dome or quaquaversal fold composed of rocks of Eocene age. The major axis of the fold strikes N.5W. All of the topographic high portion of the island is a part of the structural uplift. The crest of the fold is broad and flat with the dips increasing on the flanks. How far tilted strata may continue beyond the line where the Eocene beds are covered by recent sands and detrital material is not known. Superimposed on the general structure are a few small irregularities in the form of minor folding and faulting. There is, however, no evidence of any major faults. The largest of the irregularities lies to the south of Jebel Dukhan and has the appearance of a sink

Jan 1, 1934

By E. E. Barker

ALTHOUGH flotation was known to be a successful process prior to 1912, Utah Copper Co.&apos;s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.&apos;s ores were on, a full flotation basis. EFFECT OF FLOTATION ON ORE RESERVES The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Sackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928

The National Research Council was organized in 1916 at the request of the President by the National Academy of Sciences, under its congressional charter, as a measure of national preparedness. The work accomplished by the council in organizing research and in securing cooperation of military and civilian agencies in the solution of military problems demonstrates its capacity for larger service. The National Academy of Sciences is therefore requested to perpetuate the National Research Council, the duties of which shall he as follows: 1. In general, to stimulate research in the mathematical, physical, and biological sciences, and in the application of these sciences to engineering, agriculture, medicine, and other useful arts, with the object of increasing knowledge, of strengthening the national defense, and of contributing in other ways to the public welfare. 2. To survey the larger possibilities of science, to formulate comprehensive projects of research, and to develop effective means of utilizing the scientific and technical resources of the country for dealing with these projects. 3. To promote cooperation in research, at horse and abroad, in order to secure concentration of effort, minimize duplication, and stimulate progress; but in all cooperative undertakings to give encouragement to individual initiative as fundamentally important to the advancement of science. 4. To serve as a means of bringing American and foreign investigators into active cooperation with the scientific and technical services of the War and Navy Departments and with those of the civil branches of the Government. 5. To direct the attention of scientific and technical investigators to the present importance of military and industrial problems in connection with the war, and to aid in the solution of these problems by organizing specific researches. 6. To gather and collate scientific and technical information, at home and abroad, in cooperation with governmental and other agencies, and to render such information available to duly accredited persons. Effective prosecution of the council&apos;s work requires the cordial collaboration of the scientific and technical branches of the Government, both military and civil. To this end representatives of the Government, upon the nomination of the National Academy of Sciences, will he designated by the President as members of the council, as heretofore, and the heads of the departments immediately concerned will continue to cooperate in every way that may be required. THE WHITE HOUSE, WOODROW WILSON. 11 May, 1918.

Jan 7, 1918

The production of petroleum in India (including Burma) increased from 334,811,624 gal.&apos; ill 1936 to 350,322,222 gal. in 1937, the highest figure in the history of the industry. The increase in 1937 was clue to an increase of some 20 million gallons from Singu, 51/2 million gallons from Attack, 11/4 million gallons from Thayetmyo, and 1 mi1lien gallons from Digboi, accompanied by decrcases of 91/2 million gallons from Yenan-gyaung and 2 million gallons from Yenangyat,. The amount of gasoline produced from natural gas during the year was 10,616,313 gal. in Burma and 456,780 gal. in the Punjab. Yenangyaung Field.—The Yenangyaung field maintained its reputation of being one of the most wonderful oil fields in the world. The total production during 1937 was less than in the previous year but the resources of the field as a whole are sufficient to ensure an adequate supply of oil for many years. At the end of 1037 there were 2910 wells producing in the field. Besides a large number of ells drilled to shallow sands, this total includes 180 hand-dug wells, whose continued existenice is one of the interesting features of the field. During the year the deep drilling activities of 1936 in the southern part of the field died down, owing to the disappointing results obtained. On the eastern flank the limit of present economic extension of the oil sands was approximately demareated. Satisfactory results continue to be obtained from gas drives in the leased blocks; gas is also injected for repressuring and storage. Casing policies continue to be carefully designed to protect the oil sands against the danger of flooding by water and, in general, production methods throughout the field are characterized by a realization of the importance of the conservation of oil and gas and the prevention of waste, whether simple or underground. Singu Field.—-In 1937 the increase in the output from the Singu field was continued. This increased production was due not only to the rapid development of the valuable area in the southern part of the field but also to the successful results obtained from the first wells to produce from behind the practically completed river training wall of the Burmah Oil

Jan 1, 1939

By V. R. Garfias, R. V. Whetzel

It has been repeatedly questioned whether estimates of oil reserves are of any practical value, as the greater number of such calculations previously made have subsequently been proved to be grossly inaccurate. But even admitting partial justification for such statements, it must be evident that some idea, however approximate, of the available reserves of essential minerals—petroleum included—is of vital importance in mapping their development and the future trend of the related industries, particularly if it is kept constantly in mind that these estimates are not only never intended as a final word but must continually be subject to revision in accordance with the changes in their component factors. The value of these estimates, therefore, hinges on the clear understanding of what is meant by reserves and that the figures can only apply within the limited time when the controlling factors remain unchanged. It should be understood, further, that while estimates of possible and probable oil deposits are as a rule but idle conjectures, appraisals of proven oil reserves can undoubtedly be made with an ever-increasing degree of accuracy. And it is with this in mind that in the present study the endeavor has been to estimate only the world&apos;s proven oil reserves and to leave out of consideration the questionable volume of the probable and possible oil reserves. Such a survey presupposes further a clear distinction between the known amount of oil underground in proven fields at any one time, and the proven reserves: the portion that can be economically brought to the surface and made available for utilization. Only a fraction of the petroleum stored underground in proven fields— usually associated with natural gas—is or can be economically brought to the surface, and not all of the oik brought to the surface is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the well is wantonly blown into the air and wasted. It is thus estimated that in the United States only some 25 per cent of the petroleum stored underground in proven fields is actually brought to the surface; and in actual practice close to 25 per cent of the total gas produced is now absolutely wasted. And the dissipation of this

Jan 1, 1936

The production of petroleum in India (including Burma) increased from 334,811,624 gal.&apos; ill 1936 to 350,322,222 gal. in 1937, the highest figure in the history of the industry. The increase in 1937 was clue to an increase of some 20 million gallons from Singu, 51/2 million gallons from Attack, 11/4 million gallons from Thayetmyo, and 1 mi1lien gallons from Digboi, accompanied by decrcases of 91/2 million gallons from Yenan-gyaung and 2 million gallons from Yenangyat,. The amount of gasoline produced from natural gas during the year was 10,616,313 gal. in Burma and 456,780 gal. in the Punjab. Yenangyaung Field.—The Yenangyaung field maintained its reputation of being one of the most wonderful oil fields in the world. The total production during 1937 was less than in the previous year but the resources of the field as a whole are sufficient to ensure an adequate supply of oil for many years. At the end of 1037 there were 2910 wells producing in the field. Besides a large number of ells drilled to shallow sands, this total includes 180 hand-dug wells, whose continued existenice is one of the interesting features of the field. During the year the deep drilling activities of 1936 in the southern part of the field died down, owing to the disappointing results obtained. On the eastern flank the limit of present economic extension of the oil sands was approximately demareated. Satisfactory results continue to be obtained from gas drives in the leased blocks; gas is also injected for repressuring and storage. Casing policies continue to be carefully designed to protect the oil sands against the danger of flooding by water and, in general, production methods throughout the field are characterized by a realization of the importance of the conservation of oil and gas and the prevention of waste, whether simple or underground. Singu Field.—-In 1937 the increase in the output from the Singu field was continued. This increased production was due not only to the rapid development of the valuable area in the southern part of the field but also to the successful results obtained from the first wells to produce from behind the practically completed river training wall of the Burmah Oil

Jan 1, 1939

By R. A. Pallanch

Sodium sulfite as a zinc retarding agent in the selective Hotation of complex lead-zinc sulfide ores was discovered by the writer in the summer of 1919 in the testing laboratory of the U. S. Smelting, Refining & Mining Co.&apos;s gravity concentrator at Midvalc. Utah. It proved to be the first reagent to give consistently good results in the laboratory on the cornpanj&apos;s Bingham ore. In December, 1919, C. A Lemke, concentrator superintendent, recommended that a flotation unit be added to the existing gravity mill to handle the mill slimes, using sodium sulfite as the zinc depressant Owing to the poor lead and zinc markets and the unfavorable royalty schedules offered by the Minerals Separation Co., the project fell through at this time. In 1921, a number of laboratory tests were made at Midvale. on other ores, among them ore from the Sunnyside mine at Eureka, Chlo. Both sodium and calcium sulfites were used with succcss on this ore. Early in 1923, further tests were made at Eureka, shortly after the Sunnyside company had resumed operations after a two-year shutdown. AS a consequence sodium sulfite was given a trial in the mill. The results showcd sufficient improvement over previous work as to warrant continuous use of this reagent in the lead circuit Exeept for a week or so in 1926 and for several weeks in April, 1927, when sodium cyanide and zinc sulfate were given trial runs in this mill. sodium sulfite has been used ever sinee.. Sodium sulfite was chosen rather than the calcim sulfite brcauscl of its gre1ater sollubility, making it possitdr. to introduee the reagent as a solutiun. This Solution is introdueed into the Marry ball mills along with the original feed of ore,. The consumption of sodium sulfite in the Sunnyside mill varies from 1/4 to 12 lb per ton of ore, the smaller amount probably being nearer the average. In February, 1924, laboratory work at Midvale demonstratcd conclusivcly that good results could be obtaincd on the company&apos;s Bingham ore and on most of the custom ores tested by using sodiuin sulfite as the zinc depressant, xanthate as the lead enhancer in the lcad circuit, followed by copper sulfate and additional xanthate to float the zinc Sodium sulfide was used to float the iron pyrite after the lead and

Jan 1, 1928

By H. C. George

Since 1911, when J. L. Dunn first used compressed air for repressuring depleted oil sands in southeast Ohio, the rejuvenation of many depleted oil fields has been directly due to repressuring by means of air or gas. Developments in repressuring in recent years have resulted in its successful use in the early life of some deep, high-pressure oil fields, conserving the natural gas dissolved in and associated with the oil by returning it to the producing oil sand after it has been compressed above the existing rock pressure of the reservoir. One of the most successful operations of this type is that of the Humble Oil & Refining Co., on the DeWalt salt dome at Sugarland, Texas. I quote from a personal communication with reference to this field: "Structurally, the field is dome-shaped, having a closure of approximately 350 ft. Production comes from a sandy shale interbedded with a clean sand and lying over a cap rock which is about 3400 ft. deep on top of the structure." A feature of the operation of this field is the production of the required amount of oil with the minimum of gas production. Wells on top of the dome have high gas-oil ratios, while those down structure have lower ratios, depending upon the distance of the well from the peak. To date, it has been possible to produce the oil needed from the wells circling the dome above the water zone and below the gas zone, and in this manner the average gas-oil ratio has been kept low. The gas from all separators is turned into a gas system which serves the entire field. From this system, all drilling rigs and utilities requiring gas for a fuel draw their requirements, and the remainder of the gas (about two-thirds of the production) is delivered to a compressor plant which boosts the pressure until it can be returned to the sand at the top of the dome where the rock pressure is 1400 lb, per square inch. "The Sugarland wells produce through 2-in. tubing with a 3/8-in. choke in one wing of the well-head manifold. The pressure builds up as high as 1300 lb, per square inch on the casing while on the tubing it varies from 0 to 900 lb. per square inch, depending upon the amount of gas produced with the oil."

Jan 1, 1931

By E. E. Barker

Although flotation was known to be a successful process prior to 1312, Utah Copper Co.&apos;s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.&apos;s ores were on a full flotation basis. Effect of Flotation on Ore Reserves The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Jackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent. became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent. and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928

By John A. Mathews

It is no longer necessary to explain to an audience like this that there are stainless or non-corrosive steels. It is still necessary to repeat, and to keep on repeating, that no one of them is stainless or non-corrosive under any and all conditions. We do not make railroad axles, springs and rails from the same kinds of steel; nor are shafts, steering-arms, gears and cap-screws made from the same type analysis. By analogy with other fields of endeavor, therefore, it is logical to expect that all the myriad conditions of corrosion due to inorganic and organic acids and salts and their mixtures in all degrees of concentration and at a wide variety of temperatures and pressures will require different materials to withstand them. Possibly stainless steel when first introduced a decade ago was expected to do too much, or suffered from overenthusiasm and lack of positive knowledge and experience on the part of its producers. Its name may have been a bit misleading too, for remarkable as this product is, it has its limitations. There are now so many different ferrous products available and calling for recognition, that we may be justified in an attempt at classification. The first division is very simple. 1. Non-corrosive steels that harden by quenching. 2. Non-corrosive steels which do not harden by quenching. We might make the classification still simpler by saying (1) those that harden by quenching, and (2) those that soften by quenching. Of course there is a border line or fringe of compositions which may possess some of both qualities under limited conditions of treatment. I have seen a steel so perfectly balanced on this border line that in its natural condition, as rolled, the outside of a 1-in. bar was soft and the inside hard, and there was quite a sharp line of demarcation in between. The hardness at the center was more than twice as great as at the surface, as measured by the Rockwell test. This border line of products does not include, however, the commercial products now available to solve the problems of industry. Let us examine the products of these two classes: Hardenable Non-cokkosive Steels This group, practically speaking, includes only the products known as "stainless iron and stainless steel." These names have a special sig-

Jan 1, 1927