Search Documents

By S. L. Tainter

This paper describes the nature of engineering and geologic services for the production stage and a review of pit design factors peculiar to the development period. The Mission pit has passed into the mining phase where development is of secondary importance; however: until the pit reaches its final size, development will be a continuing function occurring simultaneously with mining operations. The deposit occurs in an extensive zone of altered sedimentary rocks which have been fractured by three fault systems, flexed or folded, and intruded by monzonite porphyry. The deposit is a low-grade copper sulfide "porphyry" type orebody within a broad zone of pervasive hydrothermal alteration in sedimentary rocks.

Jan 12, 1965

IT is necessary that all men who wish to bring things to a certain end should think of the agents needed to attain this. Now whichever one of the above processes you wish to use you must consider the nature of the material and see whether it is disposed to render what you wish to extract. Then you must see whether you have the other agents sufficiently powerful and proportioned to attain this result, for if the things were not in harmony your work would be vain and very laborious. Therefore, if you should wish to make waters or oils by way of distilla-

Jan 1, 1942

By F. C. Holden, R. D. Buchheit

In the course of studies made on the Ti-Cu alloy system,' particles identified visually as TiH were encountered unexpectedly in a specimen of high-purity Ti-0.8Cu alloy. The particles did not appear immediately after preparation, but following-storage in a dessicator for several days. Since the alloy had been vacuum annealed to a low hydrogen concentration (19 ppm by vacuum-fusion analysis), the appearance of the TiH particles was suspected as a surface contamination effect. A specimen of a Ti-0.8Cu alloy had been annealed 2 hr at 790°C and water quenched, to produce the single-phase equiaxed a structure. The metallo-graphic sample was ground through 600X paper, rough-polished on a high-speed wheel with a mixture of alumina and chromic acid, awLhish-polished on a slow-speed wheel. Disturbed metal layers were removed from the final surface by alternately etching with a 1 1/2 HF-3 1/2 HNO3-95 H2O solution and polishing on the slow-speed wheel with fine alumina. The final surface was swab-etched with a 1 1/2 HF-3 1/2 HNO3-95 H2O solution, rinsed in tap water, and dried in a stream of filtered air. The micro-structure, shown in Fig. 1, was composed of equiaxed a grains without any trace of second phase. After storage in a dessicator for 3 days, the appearance of small particles in the structure became evident (see Fig. 2). After 7 days of storage, the particles were more distinct, and in some grains, began to appear as elongated particles. The specimen then was etched a second time (without repolishing) to produce the structure shown in Fig. 4. On the basis of micro- structural observation, the line markings were identified as TiH; attempts to obtain diffraction patterns from the surface for positive identification were not successful. That the structure is a surface effect was demonstrated by grinding with 240X paper to remove the surface layer. The surface then was ground, polished, and etched using the procedures described previously. The same observations were made: the freshly prepared surface was devoid of any second phase, whereas the particles again appeared after several days storage. The same effect has been observed in other a-stabilized titanium alloys, including a high-purity Ti-0.20 alloy containing only 16 ppm H by analysis. The effect has not yet been observed in unalloyed titanium, nor does its appearance appear to be consistent with any particular alloy system. From these observations, it is concluded that certain a-titanium alloys are susceptible to the formation of titanium hydride at the surface of metallo-graphic specimens. The hydrogen probably is diffused into the surface from a residual film of etchant decomposition products. Estimates of the hydrogen

Jan 1, 1961

By Walter S. Weeks

IN this paper the effect of natural ventilation pressures is considered a part of the mine resistance and it is shown that their effect on the mine resistance is not the same as the total natural ventilation pressure of the shafts if the mine has several levels. It is shown that increasing the fan pressure causes the division of the air to approach the condition that would obtain if there were no natural ventilation pressure present. It is shown that if an appreciable difference in pressure is maintained between the beginning and end of a group of splits, the value of the integrated effect of the natural ventilation pressures on the individual splits does not change substantially with moderate changes of this pressure. A method is outlined for determining the resistance factor of the mine and the value of the effect of natural ventilation with the fan operating; also a method for determining this factor when circulation is caused by natural ventilation alone. NATURAL VENTILATION PRESSURE Natural ventilation pressure (N.V.P.) is caused by the difference in weight of the air in two similar columns between two horizontal planes, and the difference in weight is caused principally by the difference in temperature of the two columns. The fan pressure causes some variation in density, but, since it is usually small and affects both columns, its effect is relatively unimportant. It has been suggested that "N.V.P." be called "stack effect"; but, since the term N.V.P. was used in a previous Institute paper,' applied in exactly the same manner, the term will be used. FRICTIONAL RESISTANCE The frictional resistance to flow in a mine without natural ventilation may be expressed as RQ2 where R is a constant for a given air density and Q is the rate of flow. This frictional resistance plus the effect of velocity changes will be called the F pressure (F.P.) and a curve of F.P. against Q, the F characteristic of the mine. If a pressure is applied to a mine by a fan, the air flow so adjusts itself that the drop in pressure through any path from entrance to exit of mine, due to frictional resistances and velocity changes, is the same as that in any other path. The mine resistance varies as the square of the quantity. The air distribution without N.V.P. will be called "normal." NATURAL VENTILATION PRESENT When N.V.P. is irregularly distributed in a mine, it is more convenient in analysis to consider the N.V.P. as a part of the duct resistance. If it is so considered the resistance no longer varies as the square of the quantity, and if N.V.P. exists between levels the distribution of the air is no longer normal. The total N.V.P. of the mine is the pressure caused by the full length of the shafts. If a mine has several levels, N.V.P. exists

Jan 1, 1944

By J. W. Fredrickson

VERY little information is available in the literature concerning the solubility of magnesium in titanium. Aust and Pidgeon&apos; report the solubility of titanium in magnesium to be 0.0025 pct at 650°C and 0.015 pct at 850°C. X-ray diffraction studies failed to detect any evidence of solid solubility. Based on the fact that the addition of titanium to magnesium increases the c/a ratio of magnesium, Busk&apos; suggested that the Mg-Ti system, like the Mg-Zr, is a peritectic. Eisenreich- eported the solubility of titanium in magnesium to be 0.003 pct at 655°C and 0.064 pct at 760°C. Removal of hydrogen from the melt increased the solubility of titanium to 0.115 pct at 800°C. Eisenreich proposes a peritectic-type diagram for the high magnesium side of the system. Recent work&apos; with Ti-Mg diffusion couples indicate that the solid solubility of titanium in magnesium is extremely small and that there is limited solid solubility of magnesium in titanium. Experimental work on the Ti-Mg system is complicated by the fact that the boiling point of magnesium is considerably below the melting point of titanium. Consequently, the usual alloying methods are impractical. Alloying was accomplished in this investigation by sheath-rolling compressed compacts." The alloys were made from titanium sponge and high purity magnesium. Chemical analysis of the sponge showed 0.04 pct Mg, <0.005 pct Al, <0.001 pct Cu, 0.05 pct Fe, 0.022 pct Mn, <0.0025 pct Ni, 0.007 pct Si, <0.005 pct V, and <0.01 pct Zn. All heat treating was conducted in a protective atmosphere by encapsulating the specimens in fused silica ampules under a partial pressure of helium. Equilibrium was achieved by holding the specimens at temperature for periods of 24 to 120 hr. The alloys were hot rolled, cold rolled, and annealed prior to solution heat treatment. Fig. 1 shows the constitutional diagram obtained for the Ti-Mg system up to 1.5 pct Mg. Oxygen was known to be present in the alloys; therefore, it is necessary to consider the alloys as ternary rather than binary and the diagram should be viewed as a plot of a section through the Ti-Mg-0 system. Other investigatorso have shown that the addition of oxy- gen to titanium stabilizes the a phase. The data presented in Fig. 1 indicate that the addition of magnesium to titanium tends to stabilize the p phase. Armour Research Foundation7 has shown that the addition of magnesium to zirconium lowers the a transus and is classified as a p stabilizer in that system. Magnesium is soluble in solid titanium to the extent of at least 1.5 pct in both the a and /3 phases. No intermetallic compounds or magnesium-rich phases were observed either by light microscopy or X-ray diffraction. However, this does not negate the possibility that such phases exist at higher alloy concentrations.

Jan 1, 1956

The production of bituminous coal in Pennsylvania started a few years after that in Virginia. For forty-five years all the production came from the Pittsburgh bed, and since that time its total output in value has exceeded that of any other single mineral deposit in the world. It has been impossible to separate the outputs of the four counties producing it at that time, as none of it came from Greene County until many years later, and the figures in the first column of Table 49 represent all the coal coming from Allegheny, Fayette, Washington and Westmoreland Counties. The years prior to 1790 are grouped on account of space limitations, they were made in the same manner as the later ones. All outputs have been rounded into hundreds, or thousands of tons because their accuracy does not warrant further subdivision. All figures are net tons, and all represent production and not shipments; this distinction in the early days when transportation facilities were scarce meant a great deal. In the period 1820-1835, more coal was used in salt-making in western Pennsylvania than for any other single purpose, but not a ton of such coal was handled by any transport agency. Later the iron industry used large quantities of local coal without shipment, and other instances can be cited. Prior to 1832, the only means of shipment of coal, excepting by wagons, was by the rivers, and this tonnage was larger than is generally believed. In Table 23, all of the available data about production from the Pittsburgh bed have been shown. After 1844 the river shipments above Pittsburgh are accurately reported by the Monongahela Navigation Company, but its figures do not include tonnage loaded on the river below Dam No. 1, nor that brought down Saw Mill Run. Prior to 1844 no tonnage records were kept although the amount moved was considerable. The information about local production, not shipped, whether used domestically or for manufacturing is necessarily incomplete. Column 7, shipments by railroad, river and canal, includes the figures in column 4, and until at least 1857 are quite evidently too low. The figures in column 9 are largely estimates based on the data shown and prior to 1870, and perhaps later, are much more likely to be lower, rather than higher, than the actual ones. This table was prepared over a period of years, and as additional data were found the revisions necessary were almost always upward. Clearfield County was the next producer in the state, shipments-in small amounts going down the Susquehanna River; some were made later via the West Branch Canal. Railroad facilities became available in 1862, and the growth in production increased rapidly and steadily. All available data and the estimated totals are in Table 24. Butler County began mining a few years after Clearfield, the early output

Jan 1, 1942

By H. Brandhorst, C. G. Dunn

THE main purpose of the present note is to provide further information on the effect of orientation on strain-induced grain boundary migration in sheet material. A secondary purpose is to draw attention to the presence of a possible (hkl) dependent surface energy driving force, when the two grains of a bicrystal specimen have different (hk2) planes at the gas-metal interface, and to suggest means of eliminating this effect from the strain effect. If two grains A and B of a bicrystal have specific surface energies ? A and ? B respectively, there exists a driving force for grain boundary migration equal to 2(? B - ? A)/t, where t is the thickness of the specimen.&apos; When t is quite small and the residual strain energy densities €A and €B of grains A and B, respectively, adjacent to the boundary are nearly equal, it is possible that the surface effect may be larger than the strain effect. he difference € B - € A gives a driving force per unit area of grain boundary due to an applied strain.)2 However, with increasing t the surface effect decreases while the strain effect presumably remains constant. Therefore, at some sufficiently large value of t, it is possible to ignore surface energy driving forces.* On the other hand, the surface effect is eliminated for all value of t when both grains have the same (hkl) orientation or have identical values of surface energy. Although the previous study provided information on the effect of orientation on strain-induced erain boundary migration,&apos; no orientations with the (100) plane in the plane of the sheet were included. The present paper provides information of this kind. A seed crystal reorientation technique4 was used to prepare a large bicrystal of silicon iron (3 1/4 pct Si) consisting of two (100) grains in the (100) [001] and (100) [Oil] orientations. After a cold rolling strain (7 pct reduction to 3/4 mm final thickness), small specimens were prepared as before2 and then annealed in hydrogen. The boundary migration was such that the grain in the (100) [011] orientation always grew. After overnight anneals at 1100° or 1000°C, none of the initial (100) [001] grain remained. An anneal of 30 min at 950°c, however, provided information on the start of boundary migration. Fig. 1 shows both the initial position (lower line) and the final position (upper curved line) of part of the boundary, as revealed by thermal grooves. In a different area, part of the final boundary was not revealed by thermal grooves; the rate of boundary migration presumably was too high for the growth front to be defined by the time dependent thermal grooving process. In another area there was a vacated intermediate position connected to the initial position of the grain boundary. This indicates that only part of the boundary

Jan 1, 1962

Discussion of the paper of G. P. Hulst, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 1865 to 1871. L. S. AUSTIN, Salt Lake City, Utah.-One question that I would like to ask is in regard to the sampling kettle which stands beside the softening furnace. How is the sample taken or melted? G. P. HULST.-The sampling kettles in question are of 45 tons capacity and are fired with coal. The lead bullion comes in on a high line in car-load lots of 30 to 40 tons. The entire lot is trucked from car, weighed over scales and thrown into the sampling kettle, which has been previously cleaned. The kettle is fired and the bullion melted, then heated up until no frozen bullion&apos; remains in the .bottom or adheres to the sides of the kettle. The kettle is scraped clean, sides and bottom, and the wet dross is skimmed Doff clean into molds. The kettle is stirred thoroughly during the period in which 24 to 30 samples of approximately ½ assay ton are taken. These samples are taken in a long-hand loci iron mold, providing for taking six to eight "gumdrops." The mold is inserted and heated to the same temperature as the molten metal, and gumdrops are clipped out and cooled in the mold by dipping &apos;the bottom of. the mold into Water. The samples should be free from fins. The gumdrops represent the contents of the kettle, and in assaying, they should not be clipped, but weighed up and the result computed. The dross bars are weighed and sawed according to old hammer and punch sample template. The sawdust represents a sample of the dross. In eases of high gold in the bullion there is a slight correction in the assay. This method of sampling was developed at the Omaha plant of the American Smelting & Refining Co., W. T.. Page, Manager, in 1903 or 1904, for adjusting differences in checking smelter sampling. L. S. AUSTIN.-The base bullion which you treat is very clean. It has been remelted, and skimmed before shipment. How rapidly can you get it through the softening furnace, and how does it compare with ordinary base bullion? G. P. HULST.-Twenty-four hours is the softening limit on these charges. In other words, it is charged into the furnace, heated up, and the first and second skimmings are taken off, and it goes into the kettle the next day; that is, 24 hr. elapse from the time the bullion is charged to the time it is in the kettle. L. S. AUSTIN.-It seems to be a long time to hold such a pure bullion. I suppose, though, it comes around conveniently so that you have a time for all the other operations of refining. Isn&apos;t that the case? MR. HULST.-Every refinery is based on those principles.

Jan 11, 1914

By A. N. Holden, J. H. Hollomon

Inhomogeneous yielding during the early stages of plastic flow has been observed in many metals and has long been a subject of controversy. Low carbon steel, when strained at room temperature, exhibits a distinct yield point at which the metal ceases to behave elastically and begins to flow plastically without further increase in stress,† often with an actual decrease in stress from that existing at the yield point. One manifestation of this behavior is the familiar Lüders lines. The extent of the yield point elongation (the plastic strain which results without raising the stress above that at the initial yield point) may be several percent. Several explanations of this type of yielding in steels have appeared in the literature:1-3}; 1. The segregation of carbides or other constituents at the grain boundaries of ferrite forms cell-like blocks which break down at a higher stress than that at which the ferrite alone will flow. 2. The precipitation of various constituents within the ferrite itself in some way blocks initial flow until a higher stress is reached, after which a great deal of flow occurs without further increase in stress. 3. The restraining influence of neighboring, less favorably oriented grains in a polycrystal results in a storing up of energy, which on yielding is sufficient to cause the continued propagation of slip bands on the multiplicity of slip systems available in adjacent iron crystals without increase in stress. 4. Local segregation of carbon atoms increases the stress required for the initial propagation of dislocations. The stress required for further deformation is lower.3 Such an explanation would require the presence of upper and lower yield points in single crystals. Low and Gensamer2 have shown that heterogeneous yielding can be eliminated by removal of carbon and nitrogen from polycrystalline steels by wet-hydrogen treatment. They also demonstrated that the re-introduction of minute amounts of carbon or nitrogen caused a return of the yield point. Observations of the initial flow of single crystals containing small amounts of carbon and nitrogen- should provide a clue to the explanation of inhomogeneous yielding. Previous tests of iron crystals4-6 can not be considered conclusive because it is uncertain whether the carbon and nitrogen were satisfactorily removed by the decarburization technique employed. The purpose of the experiments described herein was to determine whether single iron crystals containing either carbon or nitrogen would exhibit in-homogeneous yielding. Experimental Procedures THE PREPARATION OF SINGLE CRYSTALS All crvstals were formed in the following way. Aluminum killed sheet material 80 mils thick was machined into specimens of the outer contour shown in Fig 1. These mildly tapered specimens were decarburized at 730°C for 16 hr in hydrogen that had been bubbled rapidly through water maintained at 70°. The resultant grain size after decarburizing was approximately ASTM 5. Several stress-strain curves were made of the decarburized niate-

Jan 1, 1950

The Palabora ore consists of two types, a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. The latter type also contains substantial quantities of phosphate. These two ore types are separately crushed and are kept separate through copper flotation and magnetic separation, for recovery of magnetite, with the low Ti magnetite being shipped as iron ore. High phosphate tailings are pumped to Foskor, a government-owned phosphate plant nearby. The Palabora plant was originally designed in 1966 for 33, 000 tpd using two 54 in. by 74 in. Allis -Chalmers gyratories; two 7 ft (2. 13 m) standards; four 7 ft shortheads; and six grinding lines, each using one 1,200 hp rod mill and two 1,200 hp ball mills. A fifth short- head and one more grinding line were added later; and with flowsheet improvements, the capacity of the plant was increased to 59, 500 stpd. A further plant expansion involving a third 54 in. primary and two 32 ft by 15 ft (9.75 by 4.6 m) 9,000 hp autogenous mills and another flotation section will bring its capacity to 87,500 stpd in 1977. These two fully autogenous mills are constructed entirely out of doors near the primary crusher, and the ground ore will be pumped a mile to the concentrator by a five-stage pumping system. The Palabora ore is mined with 6, 10, and 12 7d (4.6, 7.6, and 9. 2 cu m) shovels and hauled to the crushers in 110 and 165 st trucks. Sixty-five ton trucks were originally used, but the crusher dump pockets were designed for larger units. Dump pockets, crushers, feeders, and take- away belts are offset in order to keep the two ore types separate. Centerlines of the crushers are only 43 ft (13. 1 m) apart; but, because of their being offset, maintenance room is ample. Initially, more carbonatite ore than foskorite was mined; but as the pit has deepened, this ratio has been reversed. The Palabora ore breaks in the pit with a large amount of oversize boulders; and, with the use of larger trucks, a splitter has been installed on one side of each dump pocket to protect the crusher spider. Smaller trucks dump on the opposite side. To accomodate the splitter, the pocket edge has been raised one meter and moved back one meter. Dust is collected through a special vent shaft between the crushers and the mantle relining area; but even so, two high-pressure water spray headers with nozzles are installed under the edge of the pocket at each dumping position. While only one truck dumps at a time, sprays from all four headers are used to suppress dust. Any leakage of water through the seal around the upper bowl of the crusher is caught by a circular trough under the seal and directed to a sump pump. At this point, there

Jan 1, 1978

By J. H. Frye, J. W. Caum

ONE of the most important methods of increasing the hardness of metals is alloying. In spite of the widespread use of alloys, the fundamental mechanism of alloy hardening is little understood. This is true even of the simplest form of alloy, the primary substitutional solid solution in which solute atoms substitute for solvent atoms at random in the crystal lattice of the latter. A fundamental understanding of the mechanism of solid-solution hardening would be important, both because of the widespread use of alloys of this type and because of the light that might be thrown on the mechanism of hardening in more complicated alloys. The present investigation covers the hardness of primary substitutional solid solutions of zinc, gallium,, germanium; and arsenic in copper. All of these are B subgroup elements from the third period of the periodic table. Cu, Zn, Ga, Ge, and As are in groups I, II, III, IV, and V, respectively and lie just to the right of the transition elements. Because of their cost, it is unlikely that Ga-Cu and Ge-Cu solutions will ever be of commercial importance, but the intent of this study has been to discover some of the fundamentals of solid-solution hardening and it has been demonstrated that such a study is far more likely to be fruitful if alloys are made up on the basis of position of the constituent elements in the periodic table than if commercially important alloys are used. Many investigations have. been made of the hardness of substitutional solid solutions, but lack of attention to purity of the metals, infrequent grain-size control, and the use of varying testing techniques have virtually invalidated any comparisons. The purpose of most investigations has been to solve immediate problems and not to solve the primary problem: Why do solid solutions usually have a greater hardness than pure metals? PREVIOUS WORK Theories have been advanced to account for the hardness of solid solutions,, but relatively little experimental work has been done. Perhaps the first experimental work of merit was that of Norbury1 on copper alloys. He showed that for several alloys there was a correspondence between the hardness of one atomic per cent solutions and atomic volume of the solutions. More recently Brick, Martin, and Angier2 have investigated the effect of various solute elements on the hardness of copper. They concluded that the hardening effect of these solutes depended "primarily on the difference in atomic volume of solute and solvent or, relatedly, upon the parameter, change of the solvent or the extent of solid solubility." They also observed the effect of these elements on hardness and texture developed by rolling and by annealing of rolled material. Austin3 examined the hardness and response to heat-treatment of various iron solid solutions. Frye and Hume-Rothery4 measured the hardness of a number of silver solid solutions containing approximately

Jan 1, 1943

By Walter S. Weeks

In this paper the effect of natural ventilation pressures is considered a part of the mine resistance and it is shown that their effect on the mine resistance is not the same as the total natural ventilation pressure of the shafts if the mine has several levels. It is shown that increasing the fan pressure causes the division of the air to approach the condition that would obtain if there were no natural ventilation pressure present. It is shown that if an appreciable difference in pressure is maintained between the beginning and end of a group of splits, the value of the integrated effect of the natural ventilation pressures on the individual splits does not change substantially with moderate changes of this pressure. A method is outlined for determining the resistance factor of the mine and the value of the effect of natural ventilation with the fan operating; also a method for determining this factor when circulation is caused by natural ventilation alone. Natural Ventilation Pressure Natural ventilation pressure (N.V.P.) is caused by the difference in weight of the air in two similar columns between two horizontal planes, and the difference in weight is caused principally by the difference in temperature of the two columns. The fan pressure causes some variation in density, but, since it is usually small and affects both columns, its effect is relatively unimportant. It has been suggested that "N.V.P." be called "stack effect"; but, since the term N.V.P. was used in a previous Institute paper,&apos; applied in exactly the same manner, the term will be used. Frictional Resistance The frictional resistance to flow in a mine without natural ventilation may be expressed as RQ2 where R is a constant for a given air density and Q is the rate of flow. This frictional resistance plus the effect of velocity changes will be called the F pressure (F.P.) and a curve of F.P. against Q, the F characteristic of the mine. If a pressure is applied to a mine by a fan, the air flow so adjusts itself that the drop in pressure through any path from entrance to exit of mine, due to frictional resistances and velocity changes, is the same as that in any other path. The mine resistance varies as the square of the quantity. The air distribution without N.V.P. will be called "normal." Natural Ventilation Present When N.V.P. is irregularly distributed in a mine, it is more convenient in analysis to consider the N.V.P. as a part of the duct resistance. If it is so considered the resistance no longer varies as the square of the quantity, and if N.V.P. exists between levels the distribution of the air is no longer normal. The total N.V.P. of the mine is the pressure caused by the full length of the shafts. If a mine has several levels, N.V.P. exists

Jan 1, 1946

By L. S. Darken

IT has long been recognized that the driving force in an isothermal diffusion process may be regarded as the negative gradient of the chemical potential (partial molal free energy) of the diffusing substance. This equivalence is exactly analogous to the fact that a mechanical force is the negative gradient of the potential energy. Nernst1 in 1888 expressed these driving forces in terms of osmotic pressure, which is directly related to the chemical potential and free energy. The relationship between the diffusivity, mobility and activity coefficient of electrolytes in aqueous solution has been developed in great detail by Onsager and Fuoss2 with results which have recently been confirmed experimentally by Harped and Nuttall.3 This interpretation of the driving force in isothermal diffusion has been discussed earlier by the author 4.6 who pointed out4 that "for a system of more than two components it is no longer necessarily true that a given element tends to diffuse toward a region of lower concentration even within a single phase region"; departure from the behavior of an ideal solution may be so great that the concentration gradient and the chemical potential gradient, or activity gradient, may be of different sign, thus giving rise to "up hill" diffusion. Since, in the discussion of that paper,4 some skepticism as to the validity of this conclusion was expressed, it seemed desirable to adduce experimental evidence to support it. Evidence of such diffusion in nonmetallic systems has already been reported. For example, it was observed by Hartley11 in a series of experiments in which sodium chloride diffused from a saturated solution in about 5 pct acetone in water into a solution virtually free of salt but with essentially the same acetone concentration. Specifically, a wine glass containing crystalline salt and saturated solution was totally immersed in a large glass cylinder containing the acetone-water solution without salt; the difference in specific gravity was such as to prevent convection. Diffusion of salt was accompanied by a marked depletion 0f acetone in the wine glass; after 3 days the acetone concentration decreased from 5.37 pct at the top of the glass, where the salt concentration was low (0.93 pct), to 1.84 pct at the bottom where the salt concentration was high (21.64 pct). This "uphill" diffusion was found to be such that the partial pressure (activity) of acetone was essentially equalized throughout the system when a steady state gradient of sodium chloride was maintained. In order to demonstrate the existence of such diffusion in metals, a series of four weld-diffusion experiments was made. In these measurements pairs of steel of virtually the same carbon content, but differing markedly in alloy content, were welded at the end and held at 1050°C for about two weeks. Subsequent analysis showed that carbon had diffused so as to produce an inequality

Jan 1, 1948

By C. O. Bundranl, Peter Dehlinger, W. H. Browne

Brief laboratory investigations are described which attempt to determine optimum .sand concentrations in gel-sand and oil-sand1 well-treatments. The investigations apply to the case where sand acts as a propping agent in formation fractures. Both analytically and experimentally it is demonstrated that optimum sand concentrations can be defined. It is difficult to translate laboratory results to field treatments, however, since the relative distribution of sand and fluid in fractures may not be the same as injected. This is because fluid may penetrate the furtherest narrow portions of fractures, which would not pass sand. Optimum concentration of a monolayer of Ottawa sand in fractures of 0.025-in. width at the usual range of pressures encountered in treatments appears to be about 95 to 2 lb/gal. of gel. An investigation of abrasion of rock-walls by sand in treatments, described in the Appendix, shows that such abrasion is not probable in significant amounts. INTRODUCTION Experience in the Spraberry formation of West Texas, as well as in other formations, has shown that. sand is a necessary and vital part of gel-sand and oil-sand treatments. Many observers of treatments have also concluded that there seems to be an optimum range of sand concentration for these injections. Brief laboratory investigations were made at Battelle Memorial Institute to study flow in fractures with different sand concen- trations. To investigate the existence and range of optimum concentrations in the laboratory, however, necessitates knowledge of the mechanism by which the sand aids in increasing subsequent production. The action of sand in fractures is usually thought to be either that of a propping agent, thus providing a greater effective formation permeability; that of an abrasive in eroding fill material in fractures; or that of an abrasive eroding rock-wall irregularities along fracture surfaces. Investigations described in the Appendix show that sand does not appear to erode rock-wall materials appreciably. In a subsequent paper it is reasoned, at least for the Spraberry formation of West Texas, that the primary action of sand is not in removing fill materials in fractures. In this formation, and probably others, too, the main effect of sand appears to be that of a propping agent. Both analytical and experimental investigations were made for the case of a monolayer of sand acting as a propper, in which sand concentrations were determined that would, after treatment, permit flow of the maximum quantities of oil from the formation into a well. If too few sand grains are injected into fractures in which the bottom hole pressure has decreased appreciably below the original formation pressure, the confining pressure in the formation may become relatively large, thus compress the rock-walls around the sand grains, essentially close fractures, and so decrease the subsequent flow of oil. Similarly, if too much sand is used, the flow of oil will he impeded by the volume of sand present. THEORY Although an analytical approach to determining optimum sand concentrations involves gross assumptions.

Jan 1, 1955

By Richard J. Fruehan

ThE thermodynamic activities of nickel and chromium in liquid Ni-Cr alloys have not been previously reported. There have been several investigations on the solid alloys.1-3 In the present investigation the activity of chromium in liquid Ni-Cr alloys at 1600° C was determined by the use of the following galvanic cell, The use of galvanic cells employing solid oxide electrolytes for determining the activity of metals in solid alloys was first demonstrated by Rapp and Maak4 on Cu-Ni alloys between 700° and 1000°C. Recently Schwerdtfeger5 tested the performance of the ZrO2(CaO) electrolyte at 1600°C and found it satisfactory for oxygen pressures as low as 10"12 atm. He also demonstrated the use of solid oxide electrolytes for determining the activities in liquid metal systems in measuring the activity of manganese in Fe-Mn alloys at 1500°C. Extensive investigations have been carried out in this laboratory, exploring the oxygen partial pressure lower limit at which ZrO2(CaO) electrolyte can be used satisfactorily in oxygen galvanic cells at 1600°C. In a paper to be published at a later date,9 it is demonstrated conclusively that ZrO2(CaO) exhibits insignificant electronic conductivity at oxygen pressures down to about 3 x 10"13 atm which is lower than the oxygen partial pressure in equilibrium with Cr-Cr2O3 at 1600°C. Therefore, the activity of chromium can be related to the measured reversible electromotive force of the cell in the present investigation since no electronic short circulating will occur. Fig. 1 is a schematic diagram of the cell used. The Cr-Cr2O3 electrode was made of equal weights of chromium and Cr2O3 powders which were mixed and packed into a recrystallized alumina crucible. A Pt-wire lead was embedded into the Cr-Cr2O3 compact to insure good contact. A ZrO2(CaO) crucible, supplied by the Zirconium Corp. of America, contained the Ni-Cr melt equilibrated with solid Cr2O3. The ZrO2(CaO) crucible was placed on the Cr-Cr2O3 electrode and additional Cr-Cr2O3 mixture was packed around it. Contact with the Ni-Cr alloy was made with a Cr2O3 tube, which is a weak electronic conductor. A platinum wire lead was attached to the Cr2O3 tube. The galvanic cell was lowered slowly into the hot zone of the furnace tube in order to avoid too large a thermal shock which could break the ZrO2 (CaO) crucible. The furnace was con- tinuously flushed with purified argon during the experiment. The temperature was measured with a Pt-Pt/10 pet Rh thermocouple and maintained at 1600° ± 5°C. The electromotive force was measured with a recording potentiometer. The furnace was turned off when measurements were being made in order to avoid induction effects and the reversibility of the cell was demonstrated in the usual manner. The electromotive force was measured several times over a period of approximately 1 hr. During that period the electromotive force remained constant within ± 3 pet and did not continuously drift in any one direction. After the experiment the alloys were analyzed for chromium in the usual manner. The measured electromotive forces of the cell at 1600°C, (2912°F), are listed in Table I. The activity of chromium, with solid pure chromium as the reference state, (a), was calculated using Eq. [l], , n F E I, n lna RT- U] where E is the measured electromotive force, F is the Faraday constant, and n is equal to 3, the number of equivalents per mole, (nF/RT = 18.59 volts&apos;1 at 1600°C). The resulting activities are listed in Table I. The activity of chromium relative to pure liquid chromium was also calculated. The free energy of fusion of chromium at 1600° C was calculated using

Jan 1, 1969

By C. S. Smith

The partial persistence of grain size and grain shape on melting and resolidifying crystalline substances, as well as the general effects of pre-solidifi-cation and of superheating on nuclea-tion rate, have been attributed to the presence in the liquid of crystalline impurities bearing some structural relation to the principal solid and hence capable of serving as nuclei for its crystallization. That such lattice matching does sometimes occur is well established, but it is surely improbable that a compound possessing both high-temperature stability and the requisite structural similarity should be naturally available in almost every system. It is now suggested that a mechanism for producing appropriate nuclei exists in the crystallization of all but absolutely pure substances. Impurities can he of many kinds. Some will give rise to compounds that are less soluble in the solid crystal than in the liquid. A . crystal forming from a melt or solution containing these will be supersaturated in some degree, and the foreign atoms will commence to segregate during or after solidification. They do not necessarily form pure, unstrained, crystals of the precipitating compound with its normal composition and structure. Generally—at least in the metallurgical examples that have been most studied —the first recognizable nuclei have lattice coherency with the surrounding matrix and have practically the same crystal structure and lattice spacing as the material in which they form, differ- ing only in composition. An extremely thin oxide layer formed under appropriate conditions on or in a solid metal will tend to be coherent with the metal lattice, and the first few atom layers of the oxide in contact with the metal will differ in both composition and structure from massive crystalliue oxide. It will resemble the metal more closely than the oxide. If it did not subsequently change on melting, such an oxide film would constitute an almost perfect "template" or two-dimensional matrix to hold a few atoms of the primary metal in the exact array needed to form a nucleus for solidification. Any precipitating material will adopt the correct spacing over a few atom diameters, and with appropriate substitution of other atoms of the correct sizes a precipitate can match the parent lattice over large areas of cohererlce without excessive strain. In metals, the componentsof a host of oxides, silicides, borides, nitrides, carbides, sulphides, and other compounds are always present in minute amounts. Some of these will be eliminated because of extreme insolubility in the liquid, while others will remain soluble in the solid; occasionally, however, particles will be formed in the solid by coherent precipitation—not of pure substances, but of whatever assortment of atoms best satisfies the joint requirements of availability, affinity, and appropriate average atom size. Of these, many will disappear on melting, but a few will persist unmelted as little rafts of complex composition, maintaining in the liquid a surface of the exact geometry needed to nucleate the solid on subsequent cooling. Their number and size distribution will determine the resulting grain size; the dimensions of the largest will determine the degree of undercooling that can occur before solidification commences. A similar process may operate in the case of phase transformations in solids. The coherent precipitation of supersaturated minor constituents in a low-temperature phase should facilitate the nucleation of this phase on subsequent cooling after transforming into another phase at higher temperatures. At first sight this hypothesis may seem little different from the older ones. It should therefore be emphasized that it does not depend on chance to provide the right compound to form a nucleus, but postulates that every crystal, containing minute amourlts of any of a wide range of impurities, automatically engenders particles having the correct surface structure to serve as nuclei for subsequent solidification. It could operate in any system, metallic, organic, or inorganic. The suggested mechanism is closely analogous to the production of antibodies from antigens in living organisms—indeed, it was a description of the matrix theory of this process that suggested to the writer its crystalline analogue.

Jan 1, 1950

By J. E. Drury, W. M. Byers, E. J. Lynch

Measurements made with starch ~~~~s indicate that the Presence of starch serves to depress the streaming potential of a clay mud system. Measurements with pure starch slurries show that the addition of NaCl or CaO reduces the streaming potential significantly. The addition of NaOH, however, causes only a minor reduction in potential even when there are large changes in mud resistivity. INTRODUCTION In their excellent study of the streaming potential, Hill and Anderson&apos; proposed that the presence of conductive solids within the filter medium will reduce the generated potential. This theory was demonstrated with measurements on shaly sandstone cores having various "b" factors; the cores with the higher negative b factors showed markedly lower potentials. (The factor b was originally defined by Hill and Milburn2 in an expression relating the resistivity of a shaly sandstone to the resistivity of the interstitial water: log F, = log F,, + b (log 100R,)&apos;. &apos;he factor b, therefore, is a measure of the contribution of the conductive solids to the total conductivity of the sample. It has been found experimentally to be directly related to the amount of chemically exchangeable ion per unit pore volume.) In the logical extension of this hypothesis to the streaming potential created by filtration through mud cakes, they suggested that the presence of nonconductive starch in a drilling mud would have the opposite effect; i.e., it would cause the streaming POtential to be increased. The high streaming potentials that they observed with lime muds were attributed to this cause. A cross-plot of some of their results which are relevant to this discussion is given in Fig. 1. The lime-mud curves and untreated-mud curve are taken from curves given in their paper. The gyp-mud line was estimated from their statement that the measured streaming potential for gyp muds in the range of 1.5 to 2.0 ohm-m was approximately 18 mv/1,000 psi. These gyp-mud potentials were the lowest that they reported for any of the bentonitic-clay muds, and were the only ones which were less than the untreated-mud potentials. This very low streaming potential of gyp muds has also been observed in field studies.&apos; By way of comparison, a U. of Texas publication4 gives the approxi-ate compositions for lime and gyp muds shown in Table 1. These materials are added to a bentonitic-clay mud base. It can be seen that both of these muds contain significant amounts of calcium salts and that the gyp mud has the higher concentration of starch. It would appear from this and from the data shown in Fig. 1 that starch may well be the cause of a streaming-potential reduction, rather than a potential increase. EXPERIMENTAL A series of streaming-potential experiments has been performed using a cell of a design similar to that reported by Wyllie.5 Calomel electrodes were used in both the mud slurry and the filtrate. Pressure in the cell was generated with high-pressure nitrogen. The primary objective of the investigation was to determine the effect of starch on the potential. Five different slurries were made which ranged in composition from untreated ben-tonitic mud (Baroid Aquagel) to a pure starch suspension (Baroid Im-permex). The intermediate slurries were prepared by mixing together a 9-lb/bbl clay mud with a 12-lb/bbl starch suspension in the ratios 1:3, 1:1 and 3:1. When starch was used alone, it was necessary to use an 18-Ib/bbl mixture, since leaner mixtures would not form a suitable filter cake. The clay mud used in the experiments was aged for three months before use. In addition to this series of measurements on the starch-clay mud mixtures, other experiments were performed to determine the effect on the potential of the absolute starch and Aquagel concentration, and the effect of adding various chemicals. RESULTS The effect of starch on the streaming potential is shown clcarly in Fig 2. Increasing percentages of starch resulted in n continually decreasing

By G. B. Thomas

Several methods of analyzing pressure build-up data in wells have been presented by various authors. This paper reviews the theory and method of D. R. Horner and presents example calculations performed on data obtained by testing several different types of wells. These calculations include, (1) graphical estimation of final static pressure, (2) determination of the productive capacity of the pay away from the well bore and. (3) the degree to which the formation adjacent to the well bore has been damaged by completion or other causes. The methods of testing and precautions which should be taken to assure the best data possible are discussed. Limitations and reliability of calculated results are also treated. INTRODUCTION Pressure testing of wells is generally limited to the determination of producing and static mean formation pressures. The so-called "static" pressure determination.. along with PVT, electric log and production data, enable the reservoir engineer to determine, within reasonable limits, the drive mechanism of the reservoir and in some cases. the amount of edge water encroachment. Producing pressure tests enable calculation of productivity indices and allow the engineer to plan the systematic production of a pool for optimum conservation of suhsurface energy. The radial flow formula advanced by Muskat&apos; has been based on the assumption of incompressible radial fluid flow. It has been known that reservoir fluids do not behave in an ideally incompressible manner. For example, incompressible flow theory indicates a simple logarithmic relationship between the difference of the instantaneous and static well pressures when plotted against time. &apos;The latter stages of this type of plot of pressure build-up data generally show a marked devia-, tion from the earlier straight line trend. which deviation may be shown to be due to the compressible flow of fluids toward the well bore. Shut-in times of 24, 48. 72. or at most 96 hours are currently in wide use for determining so-called "static" reservoir pressure. Due to the continuation of compressible flow of fluids into the well bore long after this arbitrarily taken shut-in time, the determination of static pressures has almost invariably resulted in lower than equilibrium values. Materials balance calculations made early in the life of a reservoir often result in a calculated reserve which later observations prove to be too low. Failure to obtain reliable "static" reservoir pressures within the prescribed 24 or 48-hour build-up period has undoubtedly been a major factor in obtaining these low estimates. Comparison of theoretical and actual productivity performance has indicated that formation damage and not being able to attain true static pressures have been partially responsible for the observed discrepancies. Research into the theory of compressible flow behavior has resulted in methods of applying these theories to the testing of wells. Application of the developed theories to pressure build-up performance indicates that in many cases the following can be estimated. 1. The static reservoir pressure. 2. The in-place effective formation permeability away from the well bore. 3. The degree or extent by which the formation has been damaged adjacent to the well bore, either through completion methods or subsequent damage due to fluid entry. REVIEW OF THEORY Horner2 has shown that the pressure build-up within a "point source" well is approximated by the following formula: Equation (1) is the approximate "point source" solution to the radial compressible flow equation advanced by Muskat. The solution assumes the following: 1. A point source well is producing at constant rate from the center of an infinite reservoir with a constant pressure at its external boundary. 2. The fluid flowing is present in one phase only. 3. The compressibility and absolute viscosity of the fluid remain essentially constant over the range of temperature and pressure variation encountered. 4. The well i.; shut-in at the sand face arid there is 110 after production into the well bore. 5. The formation permeability is homogeneous in the direction of flow. From Equation (1) it can be seen that if an ideal well were shut-in while producing from a reservoir under the conditions assumed, the pressure build-up would be a logarithmic func-

Jan 1, 1953

By T. R. A. Gokcen

THE possibilities of separating and purifying metals by high vacuum distillation were examined by Kroll.1 He suggested vacuum treatment for the removal of zinc from the lead produced after Parkes desilverizing. The St. Joseph Lead Co. developed the first commercial vacuum dezincing process at their Herculaneum refinery, as described by Isbell.² The Broken Hill Associated Smelters at Port Pirie, Australia, has, after several years of pilot plant operations and fundamental investigations, developed a continuous process, which will be described briefly in a forthcoming publication." As the full-scale continuous vacuum dezincing plant at Port Pirie is still experimental, publication of full practical details of the plant will be deferred until the unit is operating as a normal part of the continuous refinery. This paper deals only with theoretical aspects of vacuum distillation processes, with particular reference to vacuum dezincing. The method of mathematical analysis is of general interest as it may be applicable to other metallurgical separations which have been investigated recently.4-6 Evaporation Processes At about atmospheric pressure, or higher, most liquids possess a boiling point—a temperature at which any heat put into the liquid is absorbed only as latent heat, not as specific heat. If a steady heat input is supplied, the liquid&apos;s temperature rises to this value, then remains constant while bubbles of vapor form beneath the surface. The rate of evaporation is determined solely by the rate of heat transfer to the liquid; the temperature of boiling is determined by the partial pressures of the volatile constituents in the liquid, and the total pressure above the surface. If the rate of heat transfer to the liquid is increased, the temperature remains constant, and the rate of boiling increases. When evaporating metals under vacuum, however, the partial pressures concerned are generally so small that boiling does not occur, because at even a fraction of a millimeter below the surface the hydrostatic pressure is usually too great to permit the formation of a pocket of vapor. In addition, the high thermal conductivity of metals tends to prevent the local superheating which is necessary for bubble formation.&apos; Although this effect is doubtless also exerted when boiling metals at higher pressures, the magnitude will be less because the degree of superheat required to form bubbles is very much less at the higher temperatures involved. Under vacuum, therefore, evaporation of volatile constituents takes place only from the exposed surface, and the rate of evaporation depends upon the surface area, the surface concentration of volatile constituents, the surface temperature, and the partial pressures of volatile constituents immediately above the surface. If the heat input is raised above a certain level, the effect is not to increase the evaporation rate at constant temperature, but to raise the temperature of the liquid until at some higher level an increased rate of evaporation (and thus of latent heat absorption) again balances the heat input rate.? Many substances (including metals) have a very large intrinsic evaporation rate at quite low temperatures—far below their normal boiling points. However, at atmospheric pressure, the large numbers of atoms evaporated are almost completely deflected back into the liquid (or solid) surface by air molecules. Thus the back condensation rate is practically equal to the gross evaporation rate, and the net evaporation rate is practically zero. It can therefore be seen that an overall distillation rate depends not only upon the intrinsic evaporation rate, but also upon the ability of the volatile atoms to move away from the evaporating surface. This movement is facilitated by the provision of a condensing surface close by. Vacuum Distillation: The function of the vacuum above the evaporating surface is to remove foreign molecules, so that the chances of deflection of an evaporated atom back into its source are reduced. When the residual gas pressure is reduced so far that the evaporated atoms have a high probability of reaching a nearby condensing surface without suffering collision with a foreign molecule, the state of affairs is termed "molecular distillation." This process is practiced commercially today for the purification of numerous organic chemical products of high unit value, but not, to the writer&apos;s knowledge, for any metallurgical separation. When the degree of vacuum produced in a still is not sufficient to promote molecular distillation, then the evaporated molecules must diffuse through the

Jan 1, 1954

By W. A. Hoyer

A pulsed high-energy neturon-induced spectral logging tool has been built and field-tested. The reaction of deuterium on tritium is used to generate pulses of 14-Mev neutrons. By detecting only the prompt gamma rays produced by neutron inelastic reactions in the formation, the presence and relative abundance of carbon, oxygen, calcium, silicon and other important elements may be ascertained from a gamma-ray spectrum. Gamma-ray spectra obtained in a shallow test well and in experimental field use show that it is possible to identify formations and their contained fluids. INTRODUCTION The penetrating gamma rays from naturally occurring radioactive elements in subsurface formations have been used for a number of years in well logging as a means of characterizing and distinguishing strata. Still another nuclear logging method which has been employed for some years consists of the bombardment of strata with neutrons and the measurement of the number of gamma rays produced by neutron capture reactions involving elements in subsurface strata.&apos; Since one of the principal elements entering into capture reactions is hydrogen, the latter procedure essentially results in a hydrogen log, whether the hydrogen be in combined form in either oil or water; thus, the log gives an indirect measure of porosity. These methods, with various refinements, have been developed to such an extent that they have become routine procedures in formation evaluation. Neither gamma-ray logging nor conventional neutron logging, however, yields sufficient information to permit unequivocal identification of the mineralogic composition of formations, and neither method gives information which may be used for the positive identification of hydrocarbons in strata. Accordingly, a number of efforts have been made in recent years to gain additional information from nuclear logs. Brannon and Osoba have shown that it is possible to identify naturally occurring radioactive elements in subsurface formations by spectral analysis of gamma rays emanating from these elements. Such an identification is of value in the characterization of strata. A simplified form of spectral analysis of gamma radiation resulting from neutron capture reactions between elements in earth materials and bombarding neutrons has been used with some suc- cess under favorable conditions to differentiate between petroleum and water. This method relies upon the relatively high energy of gamma radiation from neutron capture by chlorine and, in effect, furnishes a chlorine log. In areas in which interstitial water is of sufficiently high salinity, this log can give valuable information on water saturation and, thus, indirectly on hydrocarbon saturation. Still another approach to obtaining more information by nuclear techniques is "activation logging", in which certain elements yield short-lived radioactive isotopes on neutron activation and, thus, can be detected by gamma-ray spectral analysis. From the standpoint of determining by nuclear logging methods the mineralogic composition of strata and the presence or absence of hydrocarbons, it is essential that information be obtained on the presence and relative amounts of several elements such as carbon, oxygen, hydrogen, calcium, silica and others. Some elements, such as hydrogen, chlorine and sulfur, can be determined by spectral analysis of gamma radiation resulting from neutron capture reactions."" Others — carbon and oxygen, for example — do not enter readily into capture reactions but do yield gamma rays of characteristic energies from inelastic scattering reactions with high-energy neutrons. Accordingly, the latter reactions are of particular interest as a means of identifying hydrocarbons in subsurface strata. Several years ago it was recognized that information requisite to the identification of subsurface strata and of contained fluids could be obtained by pulsed operation of a subsurface neutron generator and associated gamma-ray detector. It was contemplated that pulsed operation would be effective in discriminating in time that gamma radiation which results predominantly from inelastic scattering reactions from that gamma radiation arising from neutron capture reactions. Accordingly, research was continued and construction of such a device was initiated. Although many problems were encountered, they were solved successfully. The following sections describe the tool which has evolved, its performance and the results which have been obtained with it to date. THEORY OF OPERATION OF NEUTRON-INDUCED GAMMA-RAY SPECTRAL LOGGING TOOL THEORY OF INDUCED NUCLEAR REACTIONS Of fundamental importance is the fact that an element, when bombarded with neutrons, emits gamma radiation of energy characteristic of that element. In theory, therefore, an element may be identified by