Search Documents

Discussion of the paper of HOWLAND BANCROFT, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1767 to 1769. THEODORE SIMONS, Butte, Mont. (communication to the Secretary*). -While preparing maps and models for use in mining litigations the writer was frequently confronted with the problem referred to in Mr. Bancroft's paper. His chart gives the apparent angle of dip with which a vein should be plotted on a vertical section not at right angles to the strike of the vein. For a quick determination of this apparent angle the writer has used an exceedingly simple graphical method, which he believes may prove helpful to engineers engaged in practical work. It is submitted, not as a criticism of Mr. Bancroft's paper, but as a means of solving the same problem when no chart is available and when calculations would consume too much time. The writer's method requires merely a few lines marked off on a piece of tracing cloth, as shown in Fig. 1: Draw line be on any convenient scale. At b erect a perpendicular, ba. By means of a protractor cut off on ba a number of angles within the probable range of variation of dip, so that a line connecting a and c, for instance, forms an angle of 60° with be, etc. With b as a center and be as a radius, draw a circle through c. This completes the tool for solving the problem. Fig. 2 represents the line of strike of the vein and db the trace of the vertical plane on which the vein is to be plotted with the apparent angle of dip. A° is the angle which this plane makes with the strike. Fig. 3 shows the application of the method: Place line cb of tracing over line db of Fig. 2 and move fore and back until line of strike becomes tangent to the circle. Connect d with the point (a) that marks the true angle of dip as found by measurement in the mine (60° in the case illustrated). The angle adb is the apparent angle of dip (C°) to be used in the vertical section. Proof.-As stated in Mr. Bancroft's paper, the apparent angle of dip is: tan C° = sin A° tan B° (1)

Jan 12, 1914

By William M. Agar

Now that both the national and state legislatures are seeking ways of reducing expenses, the appropriations for geological investigation and for the study of mineral resources have been greatly reduced and in some cases entirely stopped. Is this policy justified? The sums saved by these reductions are always small. If the work accomplished by these surveys has no intrinsic value to the community, but is only an interesting way of spending some of the people's money when that money is plentiful, there should be no surveys at any time. If, on the other hand, they perform a necessary function, it is indeed foolish and short-sighted to save these paltry sums to the detriment of the community. It is not my purpose to undertake a general justification of geological surveys. Rather, 1 wish to call attention to the work of one state survey that has been discontinued, and to indicate ways in which the work was valuable to the people, even though that state's mineral resources are not very important, and why it should be continued. Though at one time in Connecticut's history iron mining and smelting were important, and copper was mined in appreciable quantities in two localities, it is many years since it could be regarded as a mining state. At present Connecticut stands far down among the states in the value of its mineral products. Granite for architectural and structural purposes, trap rock, clay, agricultural lime, feldspar and quartz, together with a few other nonmetallic minerals, are produced in appreciable quantities, but the natural resources of the state consist at present much more largely in its attractive scenery, woods, lakes, shore line, and in the opportunities that these offer for rest and recreation. Is the prosecution of geological work in such a state a waste of the taxpayer's money? Or can it be that though it was formerly valuable, the work is now completed? The only way to answer these questions is to review the geological work done in the past and to consider the type of information the people want, as reflected in the requests that have been received by the director of the survey in the last few years. There have been two periods during which Connecticut has supported geological work within its borders. The first began in 1835 when Percival

Jan 1, 1935

CARL HENRICH (communication to the Secretary*).-I have read with much interest the discussions of my paper by Messrs. A. S. Dwight, E. P. Mathewson, Win. B. Boggs, Jos. W. Richards, and W. C. Smith. Mr. Dwight's acknowledgment that he always-in lead smelting¬obtained better results by figuring A1203 as an acid in his slags, I may take as a confirmation of my views, notwithstanding his later conversion by, the late T. S. Austin to the latter's empirical view and way of neglecting the consideration of A1203 altogether in the composition of slags-letting the slags "dissolve" in Al203. I have a strong suspicion that Mr. Austin, in a large custom smelting plant at El Paso, has been able to keep the alumina percentage of his slags sufficiently low, not to give him much trouble, although I have also a suspicion that his furnace foreman may have had a somewhat differing opinion of the practical working of the "dissolving" theory,, whenever its applicability was tested to its limits. That Austin should have conceived the notion that the Ca of CaF2 would enter into a slag as CaO, seems hardly in accord with the recognized ability of that late metallurgist. It is a well-recognized fact that even small amounts of CaF2 will reduce the viscosity of a slag; but I did not think anyone ever had an idea that CaF2, in some mysterious way, parted with its F and coupled itself with 0 to satisfy a craving for CaO on the part of 802-least of all in a lead furnace. The "dissolving" theory for CaF2 was doubtless appropriate, and an improvement on figuring the Ca of CaF2 as CaO to satisfy the demand of Si02 for RO bases. However, I cannot understand the rationality of extending this "dissolving" theory to A1203 and to ZnO. It would be interesting to have more specific data from Mr. Mathewson in regard to the actual composition-analyses-of the slags made, when he had these unusually high alumina slags in Colorado. We "old" smelters all know that within certain limits, usually found out by rather tough experience, we could safely "disregard" A1203. In fact, I believe, we never really analyzed for alumina, except in slag analyses, when we

Jan 6, 1917

By S. Shapiro, G. Krauss

We will reply to Dr. Pitsch's discussion by 1) presenting in greater detail the single surface trace analysis which we performed on the reversed austenite plates in a single parent plate of martensite of known orientation, 2) relating the results of our analysis to the conclusions which Dr. Pitsch makes on the basis of our data, and 3) examining the validity of our selection of twenty-nine individual traces from the over 200 austenite plates which were observed in a surface of this single martensite plate. Fig. 7 shows a standard (001) projection of the martensite plate from which the austenite-martensite interface traces were taken. The traces are plotted on the projection as the small solid circles, and the great circles corresponding to the loci of plane normals which could contain each trace or could intersect the surface plane along the measured directions are also plotted. It can be seen that these great circles intersect at a point which corresponds to the normal of the surface plane on which the traces were observed. Also rate which occurred only at particularly low heating rates, see Figs. 1 and 3 in the paper.2 Since in this case the interpretation of Jana and Wayman is plausible and since we have no alternative to this interpretation, we would like to state only that the existence of a diffusion-controlled reversal at low temperatures seems to be not yet proved beyond any doubt. The author wishes to thank Professor G. Krauss for making available his manuscript prior to publication. It is also a pleasure to acknowledge the lively written discussions, which the author has had with Professors G. Krauss and C. M. Wayman prior to this communication. The financial support of the Deutsche For-schungsgemeinschaft for the work on which this communication is based is also gratefully acknowledged. plotted within small dotted circles which represent a i3 deg scatter in each of the twenty-four unit stereo-graphic triangles are our A and B poles7 and the pole P determined by Kessler and itsch.' The data presented in Fig. 7 permit a direct association of the measured traces and the various proposed habit plane poles for the reversed austenite plates in the martensite crystal. If the sample measurements do in fact

Jan 1, 1969

Discussion of the paper of Edward Keller, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 2093 to 2115. GEORGE L. HEATH, Hubbell, Mich.:-In the admirable paper quoted, is mentioned the date when the 5-g. assay was first proposed is a standard for refined metal. The author omitted, however, to mention a later paper,1 which contains a proposal for the use of a single " stock solution " of mixed acids, which has been adopted by the American Brass Co. and others. The suggestion is made that such a scheme would save time and manipulation with converter metal. Unless the low current of 0.5 ampere and the large excess of nitric acid, recommended by Mr. Keller, have been proved necessary to hold up antimony-and selenium, the use of the mixed solution which we have adopted will permit the use of 1 ampere of current per square decimeter of cathode surface, until the solutions have become colorless. At this point, we wash the covers and reduce to 0.5 ampere to prevent oxidation or contamination. The ordinary split electrodes have been used. With strong current, at least, the use of an excess of nitric acid tends to the neutralization of the solution before the end of the period, from the formation of too much ammonia., and this is detrimental. Antimony deposits more easily than arsenic, and tends to drag the latter dorm with it. There must, be some such explanation for the fact. that we have made hundreds of deposits of pure cathodes from Lake material containing no antimony, but as. high as 0.5 per cent. of arsenic. By placing an assay beaker in the Frary solenoid, or rotary device, a cathode deposit with less than 0.01 per cent. of impurity is easily obtained in one operation from 3 g. of whitneyite, carrying from 7 to 10 per cent. of arsenic. In such a case, it is necessary to test several times for end point and remove the plate as soon as no brown tint appears (at once) when hydrogen sulphide water is added to the test portion on the spot plate. Edward Keller's proportion,, of solvent figure out as 14 cc. of strong nitric to 11.4 cc. of sulphuric acid (1.84).

Jan 11, 1913

By W. H. Smith

IN the course of an investigation on chromium containing minor amounts of alloying elements, the information herein has been obtained on the crys-tallographic orientations resulting from arc melting, rolling, and annealing. The chromium used in this investigation was electrolytic flake obtained from the Electro Metallurgical Co. This material was heated for 20 hr at 1600°C in hydrogen with a dew point of about — 100°C. The oxygen and nitrogen content of the chromium after this treatment was 0.0003 pct 0 and 0.005 pct N. Five pounds of this chromium were arc melted in a water-cooled copper crucible. After arc melting, the oxygen and nitrogen contents were 0.002 and 0.025 pet, respectively. A section of this ingot is shown in Fig. 1. By means of a back-reflection Laue technique, the crystal habit of the cast ingot was determined. As expected, it was found that the [loo] was approximately the axis of the columnar grains. In this respect, chromium behaves like other body-centered-cubic metals in that a cubic axis is normal to the cold surface of the mold. A slab cut from this ingot was rolled at 600°C as follows: four 30 pct reductions were made with intermediate anneals at 1200°C for 15 min. Rolling was done with the [loo] of the columnar grains in the rolling direction. Following the final anneal, an 80 pct reduction was taken at 600 °C. The final sheet thickness was ten mils. By polishing and etching, the thickness was reduced to four mils and the grain orientation determined by the transmission Laue method using molybdenum radiation with a zirconium filter. Fig. 2 is the (110) pole figure for this material with the ideal (100) [011] and (111) [112] orientations indicated. The orientation is typical of most cold rolled body-centered-cubic metals having the [llO] of the grains approximately in the rolling direction and the (100) planes approximately in the plane of the rolled sheet. There is also evidence of some 10) [1 orientation. The grain orientation of sheet rolled 40 and 80 pct in the same direction as before at 600°C followed by recrystallization at 12000 C for 15 min was determined by a back-reflection Laue technique. A random texture was found in both cases. This 1200°C 15 min anneal was found to give complete recrystallization and some grain growth.

Jan 1, 1956

He took a great interest in technical matters and his inclination was strongly toward research investigations. At the same time he was effective in manual and mechanical work and was generally found working side by side with the men under his direction. His nature was unselfish and he was extremely popular socially. He was a member of the Coeur d'Alene Commandery, Knights Templar. Stanly A. Easton. Lieutenant.Louis Baird Louis Baird, a Lieutenant in the Royal Field Artillery of the British Army, died on the battlefield in 1915. Lieutenant Baird was born July 28, 1880, at Stirling, Scotland. His technical education was obtained at King's College, Melbourne, Australia, in 1893 to 1895, and at the Technical College at Glasgow, Scotland, in 1897 to 1900. After an apprenticeship with the Mexican J. & 8. Rec. Co. of Mexico, lasting from 1900 to 1903, he became mill superintendent for the Cia. Minera Benito, at Juarez, Zac. During the year 1905-6 he was assistant manager of the Caridelaria y Anexas, at Pinos, Zac., and from 1906 to 1907 was engineer with the Cia. Minera Jalisco, San Sebastian, Jalisco. At the time of his admission to the Institute, in 1908, he was practising as a mining engineer at Etzatlan, Jalisco, Mexico. For the next four years he practised his profession in the City of Guadalajara, Jalisco, removing, in 1913, to Ixtlan del Rio, in the State of Tepic. It was from here that he returned to England to put his services at the disposal of the British Government. The Institute is not definitely informed as to how, where, or when Lieutenant Baird met his death. iCaptain John H. Ballamy John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on Aug. 9, 1918. Captain Ballamy was born at Plvmouth. Pa.. in 1886 and graduated from' the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Rai1roa.d Company's coal mining

Jan 1, 1920

By William M. Agar

Now that both the national and state legislatures are seeking ways of reducing expenses, the appropriations for geological investigation and for the study of mineral resources have been greatly reduced and in some cases entirely stopped. Is this policy justified? The sums saved by these reductions are always small. If the work accomplished by these surveys has no intrinsic value to the community, but is only an interesting way of spending some of the people's money when that money is plentiful, there should be no surveys at any time. If, on the other hand, they perform a necessary function, it is indeed foolish and short-sighted to save these paltry sums to the detriment of the community. It is not my purpose to undertake a general justification of geological surveys. Rather, 1 wish to call attention to the work of one state survey that has been discontinued, and to indicate ways in which the work was valuable to the people, even though that state's mineral resources are not very important, and why it should be continued. Though at one time in Connecticut's history iron mining and smelting were important, and copper was mined in appreciable quantities in two localities, it is many years since it could be regarded as a mining state. At present Connecticut stands far down among the states in the value of its mineral products. Granite for architectural and structural purposes, trap rock, clay, agricultural lime, feldspar and quartz, together with a few other nonmetallic minerals, are produced in appreciable quantities, but the natural resources of the state consist at present much more largely in its attractive scenery, woods, lakes, shore line, and in the opportunities that these offer for rest and recreation. Is the prosecution of geological work in such a state a waste of the taxpayer's money? Or can it be that though it was formerly valuable, the work is now completed? The only way to answer these questions is to review the geological work done in the past and to consider the type of information the people want, as reflected in the requests that have been received by the director of the survey in the last few years. There have been two periods during which Connecticut has supported geological work within its borders. The first began in 1835 when Percival

Jan 1, 1935

By J. D. Lubahn

The Bauschinger effect, or rounding of the corner of the stress-strain curve upon reloading, represents a temporary apparent softness that is more pronounced at large strains than small and for complete unloading than for partial unloading. Interrupted creep tests on copper exhibit a similar temporary softness (high creep rate) upon reloading. The fact that the strainwise dying-out time of these effects is the same in both tensile and creep tests shows that they are related. Thus, the term Bauschinger effect appears to embrace behavior following partial or complete unloading and reloading in addition to behavior following reversed loading. It is suggested that the term may properly apply also to certain creep behaviors following a small load decrement. INTERRUPTED tensile tests at low temperatures show1 a rounding of the corner of the stress-strain curve for reloading, which indicates a temporarily low deformation resistance. In the absence of recovery, the curve soon rises to the value that would have prevailed if the test had not been interrupted. The rounding of the reloading tensile curve has sometimes been referred to1 as the Bauschinger effect, although the term is more commonly applied to low deformation resistance in compression following tensile prestrain. The unusually broad usage of the term Bauschinger eflect in ref. 1 seems justified by the obvious interconnection of the various behaviors to which it has been applied.' In fact, the following discussion will indicate that still broader usage might be desirable. The Bauschinger effect is common at room temperature but apparently disappears at higher temperatures.2 Interrupted creep tests and tensile tests were made on certified OFHC copper (nongaseous impurities exclusive of silver were 0.004 pct), cold drawn 84 pct to ½ in. diam, and annealed at 600" (about 0.025 mm grains) or 850°C (about 0.2 mm grains). The tests were made in standard creep or tensile machines, using an O.S. Peters microformer-type extensometer or, for the small plastic strains, a special arrangement employing General Electric magnetic gage heads.' Interrupted creep tests at room temperature show3,4 an initial softness after reloading, manifested by an initial creep rate that is higher than that which would have prevailed if the test had not been interrupted. Fig. 1 shows some typical examples. This effect is apparently temporary (as is that in tensile tests): in four of the five tests shown, the log rate vs strain curve becomes parallel to an

Jan 1, 1956

By G. Donald Sherman

THE intense chemical weathering of geological materials in the tropical regions has produced soils that are very rich in their content of iron and aluminum oxides. These soils are commonly referred to as laterites. There is considerable confusion as to the definition of a laterite, since there are workers who consider it to be entirely a ferruginous horizon and others who insist that laterite must have a high content of free aluminum oxide. How¬ever, in general the former is the accepted definition. The indurated ferruginous clay was given the name "laterite" by Buchanan,' not because of its bricklike appearance but rather because bricks were cut from it and used as a building material. Many of the temples of India and Siam are built of this material. This term has come to mean to the geologist a material that includes hard masses of concretionary, cellular, pisolitic ironstones. The soil scientists have deviated from the original meaning of the word and their writings show very little respect for Buchanan's definition or an understanding of the ma¬terial described by him. Pendleton," a life-long student of tropical soils, has insisted that the term laterite be restricted to Buchanan's definition; namely, an alluvial horizon, largely of iron oxides, with a slaglike, cellular or pisolitic structure, and of such a degree of hardness that it may be quarried out and used for building construction. More recently DuPreez2 and Sherman" have eliminated from Buchanan's definition the requirement of a hardness for building construction purposes. In doing this they eliminate the lithological implications in favor of a description of a product, soil, which originates and is developed by pedogenic processes. The confusion of the definition of a laterite is made greater by workers who insist that it must contain bauxite of different degrees of purity. Many of the tropical soils are rich in aluminum oxides. It is natural for the workers who have studied these tropical soils to emphasize the importance of the hydrated aluminum oxides. Hollands reported that the alumina in a laterite existed as bauxite. Fermor3 insisted that a laterite must have a high content of aluminum oxide hydrate, and Fox,4 in 1923, made the suggestion that if a laterite contained enough hydrated aluminum oxide to be used as an aluminum

Jan 1, 1952

By C. L. Baker

The district of Catoree, San Luis Potosi, ranks among the first half-dozen silver-producing camps of Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapnni, Mazapil, Palomas, Musquiz, Minas Viejas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (610 m.) in 41/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catoree from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catoree, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to crosivc forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstone?, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains: some of this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution of the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebblcs, and finer detritus. According to tradition, the higher portions of the Sierra Catoree were forested with pines and cedars but none remain within the mining district, although cedar is found farther south in the range. The vegeta-

Jan 1, 1922

By Richard Schellinger, Ronald H. Carlson, Robert D. Norris

INTRODUCTION A very important key to the success of an in-situ leach venture is proper choice of well field chemistry, in which type and concentration of oxidant plays a significant role. For proper design of well field and plant, an engineer must be able to estimate uranium production levels and their change with time. The rate controlling step in the uranium leach process is generally acknowledged to be the oxidation step (Goddard and Brosnahan, 1980; McKnight and Anthony, 1979; Mays, 1979). Uranium head grade is very dependent upon concentration of oxidant injected into the ore zone. If oxidant levels are too low, uranium production requirements will not be met; if levels ate too high, excess oxidant will be wasted in side reactions with gangue material and leach economics will suffer. To date, no reliable laboratory technique exists for generating data easily translatable to field conditions. Empirical correlations based upon lengthy field testing have been the major tools avail- able to the design engineer to date. During the past five years, FMC has developed lab- oratory techniques for studying uranium leach chemistry under conditions simulating as closely as possible the field situation. Both agitated batch and consolidated core leach procedures have been developed. Results of FMC agitated batch studies are described in detail in a companion paper (Carlson, et. al., 1980). This paper will focus on the technique developed for leaching consolidated undisturbed core under simulated down-hole conditions. Through use of a follow-up computer model (Winkley, 1980), generated data can be translated to expected field response, thus providing the design engineer with valuable information in a relatively short period of time. CHEMISTRY In addition to uranium (+4), other oxidant-consuming species present in uranium ore are iron sulfides and carbonaceous material. Iron sulfides are usually present in concentrations far exceeding those of the other two materials and, therefore, represent the major oxidant-consuming species present in uranium sandstone ore. Previous studies (Carlson, et. al., 1980) have shown that iron sulfides exist in both Texas and Wyoming ores as a mixture of pyrite and marcasite (FeSz); furthermore, uranium mineralization (existing as uraninite) was shown to exist as a fine granular material coating or imbedded in iron sulfide crystals and sand grains (i.e. quartz and feldspars). The leach chemistry of a uranium ore body can be described by the following equations using hydrogen peroxide (Hz021 as oxidant:

Jan 1, 1980

By B. F. Buie

Included in the general category of clays is a large and varied assemblage of nonmetallic silicate minerals which characteristically occur as fine-grained particles having flaky, sheetlike, or rod-shaped form. Most, though not all, are hydrous aluminum silicates. Amount and kind of impurities vary greatly, and these strongly influence the uses of the various clay types. Clays occur in a wide range of geological situations: as bedded sedimentary deposits composed of the weathering products of feldspar and other minerals; as alteration products of igneous, sedimentary, and metamorphic rocks weathered or hydrothermally altered in place; and, to a more limited extent, as hydrothermally introduced materials. TYPES AND MARKETS On the basis of chemical composition and crystal structure, two major groups of clay minerals recognized are the "kandites" or kaolin group, and the "smectites" or montmorillonite group. Another major type is illite, particularly important as a constituent of shales. Two additional mineral species having economic importance are attapulgite (palygorskite) and sepiolite. For present purposes, however, a classification based on utilization is more appropriate. The U.S. Bureau of Mines recognizes six types of clay: kaolin, ball clay, fire clay, bentonite, fuller's earth, and miscellaneous clay. Kaolin The kaolin group of minerals consists of the mineral species kaolinite, halloysite (metahalloysite), dickite, and nacrite, although the latter two are not being produced commercially. Kaolin, also called china clay, is a high-purity white material. Perhaps it is best known as a principal ingredient in the manufacture of chinaware, porcelain, and other high-quality ceramic products. However, by the mid-1970s very close to 50% of the kaolin produced in the United States was going to the paper industry for use as a filler and coating material. Manufacture of refractories uses about 12% of U.S. production. Kaolin is also used in plastics, in the rubber industry as a filler in footwear, electrical cable, and similar products, and as a conditioner of rubber for automobile tires to add strength and abrasion resistance. Smaller amounts are used in printing ink, paint, and adhesives; as insecticide carriers; in the production of catalysts for the petroleum refining industry; and in many other industrial and commercial applications. Production and use of kaolin in the United States doubled in the ten years from 1946 to 1956, and doubled again by 1966. Growth continues at a rate of about 7 % per annum.

Jan 1, 1976

By Eugene P. Pfleider

Research indicates that the cube diamond is a superior stone for drill bits. It can be oriented to combine a long cutting edge with structural strength and high resistance to wear. Test bits set with preferred orientation give double the bit life at astoundingly low diamond loss in comparison to oriented octahedral diamonds. A PROGRAM of research on the orientation of diamonds in drill bits has been under way for several years at both the United States Bureau of Mines Experimental Mine at Mount Weather, Va., and the School of Mines and Metallurgy of the University of Minnesota. Reports on past work done both in the laboratory and the field are available in the technical press.1,3,4 The results of such drilling, done under comparable conditions, show that bits having diamonds oriented in a direction that combines structural strength and greatest hardness not only can advance somewhat faster than random set bits but can do this with a unit diamond loss of 50 pct or less. Several bit manufacturers have initiated the training of diamond setters in the principles of orientation on the basis of the above-mentioned research results. The basic information on the crystallography and hardness variation of the diamond was presented in an earlier paper,' which pointed out that the diamond is several hundred times harder along certain directions and certain faces than on others. The same article discussed the drilling results obtained with a group of nine bits having octahedron diamonds set with on-point, positive (gouge) rake, and negative (drag) rake orientations. The testing of oriented cube diamonds is an extension of this research program, employing the same procedures and equipment (Hy Mac hydraulic drill unit, EXT diamond core bits, St. Cloud Pink granite) as previously described. This current work covers the test experience of seven bits set with cube diamonds running approximately 10 stones per carat. The individual stones were near perfect cubic form; hence it was simple to orient them in any desired direction. The cube is a comparatively rare crystal form of the diamond, although considerable numbers are produced from the Congo. It is understood that most of the cube diamonds are retained in Africa, where they are either used locally for diamond bit manufacture or ground up to make powder. They have been considered to be an inferior stone for drilling purposes.

Jan 1, 1954

By A. J. Lyon

THE stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening; which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging-heating in a temperature range below 170° C. (340° F.)-will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1928

By AIME

Cores must be cut in half to secure workable samples for saturation, porosity, and permeability tests. They come from the field labeled as to the type of core, well, and depth from which they came.

Jan 1, 1948

By AIME AIME

METALLIC corrosion, which results from the chemical affinity of different metals for non- metallic elements, should be considered from both the kinetic and static viewpoints. From the stand- point of statics the metals may be arranged in the order of their affinity for oxygen, chlorine or any other acid- forming element. They may also be arranged in the order of the magnitude of the heat of combination of their corresponding compounds. It is misleading to talk about some metals as "noble," because these relations are all relative; and the order varies for oxygen, chlorine or whatever the element may be. A third way to arrange the metals is by their solution pressures. These three methods indicate that one metal is better under one set of conditions, but not so good under other conditions. Considering the problem from the standpoint of kinetics, the thing which saves most metals is what may be called the sluggishness of reactions. Using organic substances as an example, we know they will all oxidize, but fortunately they do so rather slowly. An increase in temperature always means an increase in the reaction rate, and preventing corrosion at high temperatures is a greater problem than at low temperatures. A second consideration is to avoid all sub- stances which might provoke catalytic action, and as it is generally impossible to foresee what substances might do this, the thing is to avoid all substances other than the main constituents of the alloys. A third consideration is to avoid local electrolytic action, which again indicates the advisability of avoiding the contact of differing substances.

Jan 1, 1926

Vol. 54 will be sent about February 1 to members who have paid their dues for the current year. Members who do not receive copies within a reasonable time are asked to notify the Secretary.

Jan 2, 1917

There are no authentic records of production prior to 1869, although various records report local production and use in 1853 and 1860. Tonnages in Table 68 for the years 1853-1868, both inclusive, are estimated. [ ]

Jan 1, 1942

By R. W. M. Lai

This paper presents a simple flotation kinetics model (Lai, 1981) along with a method of presenting the model in an informative graphical form. Examples are given for evaluating various flotation conditions and different ore types.

Jan 1, 1983