Search Documents

By Jack A. Kanz, Samuel R. Shortes, E. C. Wurst

Zinc diffusion into GaAs from the vapor phase through reactively sputtered SiO, films Izas been inrestigated for various zinc pressures at 1000"C. Diffusions were carried out in evacuated quartz ampules with elemental zinc and with various Zn-Ga alloys. Sputtered films have proved effective in lowering surface concentrations and preventing surface deterioration during diffusion. Approxin.ate complenzentary error-function impurity distributions were found when surface concentrations were reduced to approximately 3 -—4 x 10" atoms cm'3 or less with dilute zinc sources or by diffusion through SiO, films. Zinc difhsions in GaAs tlzrough SiO, films produced more planar diffusion fronts than were observed with uncoated zuafers under identical conditions. A) Surface Deterioration During Diffusion. Device technolorn-- in compound semiconductors has been hampered by several difficult problems not normally encountered with silicon and germanium. 111-V and 11-VI compound semiconductors generally have volatile constituents at temperatures used for diffusion. To achieve specific junction depths in reasonable lengths of time, or to obtain particular impurity distributions and doping levels, it is often necessary to use temperatures which cause surface deterioration and erosion of the wafer. The resultant surfaces are generally unsuitable for devices. The type and extent of surface damage depends to varying degrees on the particular environment of diffusion and on the particular impurity in question. The most common type of deterioration results from simple dissociation of the gallium and the arsenic during diffusin.' The deterioration process is significantly enhanced by thermal gradients in the diffusion zone, usually resulting in vapor transport and condensation at the cooler portion of the system. The resulting damage sometimes appears as a general haziness over the surface or an array of pyramidal etch pits characteristic of the particular orientation. Occasionally, erosion of the surface occurs uniformly over the wafer so that surface loss is not readily apparent. Workers in GaAs usually resort to the sealed-ampule type of diffusion system3"5 rather than the more conventional open system used for silicon and germanium. Another type of deterioration results from direct interaction of the impurity with the surface. The form of deterioration may vary from surface alloying, as in the case of zinc, to direct chemical attack and vapor transport of the reaction products, as in the case of sulfur. Surface alloying with zinc occurs at higher temperatures and source vapor pressures.4 The process is largely controlled by the amount of free gallium on the surface of the wafer in equilibrium with the arsenic lost to the system. The group-VI elements, sulfur, selenium, and tellurium, are commonly used donor impurities for gallium arsenide. These elements are characterized by high vapor pressures and high chemical

Jan 1, 1964

By J. Sibakin, R. D. Hindson

In order to devise a practicable soaking pit schedule for use at The Steel Co. of Canada Ltd.'s Hamilton Works, soaking pit heating temperatures, sooking times, pit capacity, and safe maximum mill drafts were correlated with fluctuations in the current or load of the bloom mill driving motor. Other variables such as total delays in the pit, rolling schedules, mill delays, and track times were also investigated. IN order to show an easily applied and accurate means of establishing soaking pit heating temperatures, soaking times, pit capacity, and safe maximum mill drafts, these various factors are correlated herein with fluctuations in the current or load of the bloom mill driving motor. Rolling practices have a considerable influence on the production capacity of a blooming mill. The maximum values of the torque, in particular, are of importance, since even instantaneous current peaks lead to the tripping of the motor by the overload relay and result in loss of mill time. The establishment of safe maximum drafts and accelerations for ingots of different sizes and of a soaking pit practice which would ensure a consistent and satisfactory plasticity of the metal is of considerable importance for increasing the efficiency of both the blooming mill and the soaking pits. The Bloom Mill Dept. of the Hamilton Works, The Steel Co. of Canada Ltd., is equipped with one 44 in. mill driven by a 7000 hp motor with the setting of the overload relay at 22.0 ka. The speed of rotation of the motor is regulated after the Ward-Leonard system. There are three basic speeds of 9.5, 28, and 47 rpm and a further possibility of increasing the speed by weakening the field. This last possibility is hardly ever used during practical operations. The rolling program of the blooming mill is varied, both in the size of the ingots to be handled and in the steel grades. The total tonnage handled by the mill is about 2,000,000 ingot tons per year. At the time of the investigation, the Bloom Mill Dept. was equipped with 22 soaking pits (6 regenerative, 14 bottom-fired, and 2 one-way top-fired pits) with a total bottom area of 2770 sq ft. The pits are fired with a blast furnace-coke oven gas mixture having a calorific value of 155 Btu per cu ft. The foregoing figures show that the production program was such as to impose the necessity of a most efficient usage of the available equipment. For this purpose, the operations of the 44 in. mill and of the soaking pits were investigated, and the results of the investigation were used as a basis for a revised soaking pit schedule and drafting practice. The plasticity of an ingot of a certain chemical composition when being rolled is determined mainly by the following factors: I—the ingot size, both thickness and width; 2—the length of the gas soak; and 3—the surface temperature. The first two factors determine the uniformity of the temperature distribution over the cross-section of an ingot. The third factor introduces the level of the heating of an ingot. The torque produced by an ingot being rolled is determined by the area of the metal displaced, its plasticity, and acceleration values. On the other hand, with shunt motors the torque is determined by the current. This can be assumed to be correct with only a small degree of error for compound motors with a relatively small effect of the series windings as long as the velocity is not regulated by weakening the field. Since the spread is relatively unimportant when compared to the width of an ingot and since it is also reduced several times during rolling by edging passes, the draft alone and not the area of the metal displaced may be taken into consideration with ingots of a similar size. It is therefore possible to determine the main features of the heating and drafting of an ingot by measuring the current and acceleration of the mill motor. After the acceleration has been taken into account, the amount of current will be an indication of how the motor responds to a heating and/or drafting practice and these practices can be adjusted in order to get the desired result. As peak currents are more likely when heavier ingots are rolled, the rolling of plate and slab ingots was investigated. Conditions prevailing when smaller ingots are rolled can be deduced from the results obtained on heavier ingots. All measurements were made when plain carbon grades under 0.15 pct C were rolled. The motor current, the voltage across the armature, and the rpm were recorded simultaneously on synchronized charts, Fig. 1, which moved with the speed of 6 in. per min. Each draft was recorded by a special observer. The rpm curve made it possible to establish the acceleration at any given moment. For purposes of correlation, the maximum current during a pass and the corresponding acceleration were used. The charts made it possible to establish the position of the roller's lever at any given moment as well as the total time of a pass. The slab ingots were divided into three groups (28x35, 28x45, and 27Mx53 in. ingots) and each group was investigated separately. Since they account for most of the current peaks, only flat passes were used for purposes of correlation, a total of 1373 having been investigated.

Jan 1, 1956

By A. Eilers

I PRESENT herewith, for the inspection of the members of the Institute, a specimen of coke, made in gas-retorts from the lignite of Trinidad, Colorado.

Jan 1, 1874

By A. Eilers

I present herewith, for the inspection of the members of the Institute, a specimen of coke, made in gas-retorts from the lignite of Trinidad, Colorado.

The authors have done a very thorough job in analyzing the factors affecting turndown sulfur performance at Inland's No. 4 B.O.F. While many of the results are not unexpected, it is helpful I am sure to have quantified many of the relationships that the operators rely upon daily. On the other hand, however, the results shown for ladle skimming are very surprising. I do not doubt the statistical relationship shown but I feel, based on our experience at Youngstown, that some other parameter has been ignored in the data on ladle skimming. It was our experience that by skimming our hot metal transfer ladle we could reduce our lime consumption by eleven percent while obtaining sulfur removal comparable to that shown by the authors. I would like the authors comment of similar adjustments on the lime charge that were made on skimmed heats at Inland. If not, it would seem that one could gain more desulfurization in the B.O.F. by raising the hot metal manganese than by installing a skimmer. The author's state that no comparisons are valid between the data sets for the two time periods involved because of the difference in the consumption of No. 2 Bundles. I feel this in fact is one of the important conclusions to be drawn from the paper, as there seems to be approximately a 10-20 percent difference in percent of heats that are under 0.020 percent sulfur for similar conditions, which is an extremely important difference with today's demands for low sulfur. I would like the author's comments on the difference in the amount of 82 bundles consumed. Along this same line I was quite surprised by the relatively low number of heats that had a first turn down of 0.020 percent sulfur or less. Also rather disconcerting are the conditions necessary to achieve a first turn of 0.020 percent sulfur, 50 - 60 percent of the time, as required by today's specifications. It is a problem which we are well aware of, but the numbers are still shocking.

Jan 1, 1972

By William M. Newton, John E. Sherborne

The value of the electric log as a means of interpreting underground structures has been increasingly demonstrated by its almost universal present-day use. It becomes important, therefore, to be able to evaluate the factors that affect the values obtained. By far the greatest number of electric logs are measured today in boreholes filled with rotary mud, the properties of which may exert an important influence on the electric log. In an effort to establish what the order of magnitude of such effects might be, a series of investigations was made in the laboratory and the field. Apparatus suitable for either field or laboratory use was designed and a procedure established for determining the factors that affect the resistivity of drilling muds over a wide variation in mud condition. Five muds representative of the types of clay-base muds employed in California were tested and the following observations were made: 1. The effect of raising the temperature from 8o° to i8o°F. is to decrease the resistivit~ of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3. The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as baroid and limestone, tend to increase the resistivity of drilling mud. 6. Cement and counteracting reagents reduce mud resistivity. The results of the investigation indicate that the mud resistivity is materially affected by the addition of electrolytes whether these are added for the purpose of conditioning the mud or enter the mud when salt beds or highly saline structures are penetrated. It should be observed, however, that the magnitude of the effect produced upon the electric log by changes in mud resistivity is also dependent upon the relative salinity of the water en. countered in the formation being logged. The laboratory data are supplemented by field data, which indicate that both the self-potential and resistivity curves are influenced by mud resistivity.

Jan 1, 1946

By Roy A. Hardy

THE Getchell mine is a comparatively recent discovery in the old Potosi mining district, Humboldt County, Nevada, a district organized in the seventies and eighties, in which some prospecting was done in several metamorphic zones along a monzonite-sedimentary contact. The district had no production in the early days and no further work was done until the same metamorphic zones were prospected for tungsten (scheelite) in 1917 and 1918, when a few small lots were shipped. It again lay dormant until 1934, when prospectors investigated a large siliceous escarpment at one end of the old district where outcroppings were a prominent feature of the topography. Undoubtedly, during the early prospecting of the district, the outcroppings had been investigated for mineral, probably by panning, with negligible results because the gold later found is invisible in the concentrate and is refractory. A fire assay revealed the presence of sufficient gold to warrant development work. The outcroppings were easily prospected by short tunnels having their portals in the siliceous material on the hanging-wall side, with a maximum distance to crosscut to the footwall of 135 ft., or a distance at right angle to dip of 60 to 90 ft. Development work, reaching a depth of over 600 ft. on the dip of the vein, was done by means of various crosscut tunnels, winzes and laterals. A churn-drill hole was also sunk, which intersected the vein at a depth of 1100 ft. on the dip. Sufficient development work of this character was completed by 1937 to justify the erection of a reduction plant to roast the sulphide ore and cyanide the calcine, and to treat the oxidized ore by straight cyanidation, to make a doré bullion for shipment to the mint. The erection of the plant was started that year and finished early in 1938, with a combined capacity of about 800 tons per day. It has operated continuously since erection and recently was enlarged to handle 1000 tons per day. The vein dips with the slope of the mountain, and by stripping the hanging wall the ore may be mined by power shovel for several hundred feet below the outcrop. Thereafter underground methods will be necessary.

Jan 1, 1940

By F. J. Longworth

For a number of years an intensive study has been made to improve the blast-furnace practice at Copperhill not only as to costs but to provide a good grade of gas for the acid plants. This study, took us back to the fundamentals of successful pyrite smelting; namely, a blast furnace working on a clean sulfide ore, free from fines, and the use of quartz high in silica as a flux. In 1919, the quality of the flux was improved and its effect on the metallurgy was very marked. To improve the practice further, it was necessary to work out some method of treatment for the sulfide fines and the siliceous and refractory ores, other than in the blast furnace. A series of milling tests indicated that these products could be successfully treated by differential flotation, and in 1922 plans were made and a flotation plant built. It was estimated that the flotation plant would deliver to the smelter 40 to 50 tons of concentrates per day; the problem was what to do with these concentrates. It was out of the question to attempt to smelt them in a blast furnace because of the dust losses and, because our practice demands a charge free from fines for satisfactory operation. There is no custom smelter in the vicinity to which concentrates may be sold, pending the time when the tonnage will be sufficient to warrant roasters and a reverbatory furnace. Sintering and nodulizing were investigated but neither method fitted into our scheme of metallurgy. A close study of the converter practice was then made to see if some method could not be evolved to smelt this tonnage of concentrates in a converter without preliminary treatment. At that time, the converter installation consisted of two 12-ft. Great Falls converters, which were handling 12 to 14 per cent. matte. The heat balance of the converters working with 12 to 14 per cent. matte was more than sufficient to smelt the contemplated tonnage of concentrates but the mechanical difficulties. of feeding fines into the Great Falls converter made the use of this type of converter impractical.

Jan 9, 1924

By John E. Sherborne, William M. Newton

The value of the electric log as a means of interpreting underground structures has been increasingly demonstrated by its almost universal present-day use. It becomes important, therefore, to be able to evaluate the factors that affect the values obtained. By far the greatest number of electric logs are measured today in boreholes filled with rotary mud, the properties of which may exert an important influence on the electric log. In an effort to establish what the order of magnitude of such effects might be, a series of investigations was made in the laboratory and the field. Apparatus suitable for either field or laboratory use was designed and a procedure established for determining the factors that affect the resistivity of drilling muds over a wide variation in mud condition. Five muds representative of the types of clay-base muds employed in California were tested and the following observations were made: 1. The effect of raising the temperature from 8o° to i8o°F. is to decrease the resistivit~ of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3. The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as baroid and limestone, tend to increase the resistivity of drilling mud. 6. Cement and counteracting reagents reduce mud resistivity. The results of the investigation indicate that the mud resistivity is materially affected by the addition of electrolytes whether these are added for the purpose of conditioning the mud or enter the mud when salt beds or highly saline structures are penetrated. It should be observed, however, that the magnitude of the effect produced upon the electric log by changes in mud resistivity is also dependent upon the relative salinity of the water en. countered in the formation being logged. The laboratory data are supplemented by field data, which indicate that both the self-potential and resistivity curves are influenced by mud resistivity.

Jan 1, 1946

By Michael J. Messel

W. P. MOULD*—Has consideration been given to the problem of retreating the 4,000,000 ton tailings pile to recover the very considerable amount of asbestos fiber that was lost over the years due to insufficient operation and poor recoveries? Also, what was known about the possible content of chromite and the sulphides of nickel and cobalt? M. J. MESSEL (author's reply)—Consideration was given to the problem but nothing concrete has been done up to this time. W. P. MOULD—I am certain the tail- ings contain a very considerable quantity of fiber, not all of which is in the shortest lengths, because in the milling of talc rock from a neighboring location having a common origin with the asbestos bearing serpentine source of the tailings pile, a concentrate carrying 15 pct Ni and Co in complex sulphides and constituting about 4/10 of 1 pct of the talc rock was recovered. In the belief that the tailings also contained an appreciable content of chromite (then in demand, 1937) it was suggested to the management of the asbestos company that a truck load of the current tailings be sent to the flotation plant of the talc company where it would be put over the concentrating tables in an effort to discover the presence and roughly the percentages of chromite, nickel, and cobalt. Preparations for the test were woefully inadequate and the test was completely snarled up by the surprisingly large quantity of asbestos fiber from 1 in. long down to very short fiber, all of which matted up and plugged launders and pumps with disastrous effects and practically the total loss of the sample. If anything was indicaded by the test, it was that a wet process for milling asbestos was worthy of very serious consideration. M. J. MESSEL—A wet milling process for tailings retreatment only, is at present under study at our plant. One asbestos mining company in Canada has constructed a fairly large test plant for this purpose, but as yet no definite results have been obtained other than in a small test unit plant which were in some respects quite encouraging.

Jan 1, 1950

By I. J. Gardescu

The production of petroleum in Rumania in 1932 totaled 52,560,000 bbl., an increase of 6.8 per cent over 1931. The average daily production rose from 123,000 bbl. at the beginning of the year to 173,000 bbl. at the end of the year, the production in the Gura-Ocnitzei field rising from 38,800 to 80,700 bbl. per day. This increase was due to competitive development during which time the percentage of total production of the various operating companies remained practically unchanged. Chief producers were: Concordia, 30.3 per cent; Unirea, 21.6; Romano-Americana, 13.5; Steaua Romana, 8.3. Boldesti, where production of the previous year was practically doubled, would have produced far greater quantities were it not for the fact that both Astra Romana and Romano-Americana curtailed drilling operations. Of the total daily production of 21,800 bbl. a day, the Astra Romana, Steaua Romana and Romana Americana, produced respectively 67, 25 and 8 per cent. The Moreni field showed a sudden drop in production from the preceding year, due primarily to reduced drilling activities. Its production of only 21,000 bbl. a day removes it from first position for the first time in many years. All the other fields showed a decrease in production, except Ochiuri, 3 miles west of Gura-Ocnitzei, and Ceptura, 12 miles east of Boldesti. Drilling1 During the first nine months of 1932, 116 wells were completed, 8 of which were dry holes. The Meotian (lower Pliocene) is the producing horizon in 73, the Dacian (upper Pliocene) in 31, and the Oligocene in 4 of the completed wells. Three of the Oligocene wells were drilled in the Bacau district and one at Grausor, near Campina. In addition, 47 wells were drilling on Oct. 1,1932. Of the total completions and drilling wells, 92 per cent employed rotary for a footage of 98.5 per cent of the total drilled. Power for rotary drilling was furnished to 105 wells by steam, to 38 by electricity, and to one by gasoline.

Jan 1, 1933

HUBERT INGERSOLL ELLIS Hubert Ingersoll Ellis, who met accidental death on Jan. 6, 1919, in eastern Washington, had already advanced far in the profession of mining engineering and gave promise of a brilliant future. He was born on the Washington coast in June, 1889, and had his preparatory schooling at Menlo, Wash. In 1905; he entered the College of Mines of the University of Washington, and at once made a high record of scholarship. After completing 3 years of his technical course, he went to the interior of Alaska, where he spent 4 years in mining. During this time he was field correspondent for technical-magazines and wrote several important articles. In 1915, Ellis completed his senior year in the College of Mines; his graduation thesis was a comprehensive paper on mining methods at Fairbanks, Alaska, which was published as a series of articles in the Engineering and Mining Journal. On July 14, 1915, he entered the employ of the Bunker Hill & Sullivan Mining & Concentrating Co., Kellogg, Ida., as an underground miner, and was soon promoted to the position of operative on experimental metallurgy and later chemist in the same work. Later, he did exhaustive work on flotation with particular attention to the use of various addition agents. For the past 212 years, his work was largely in the field, examining mining prospects and directing work of investigation, during which time, while located at Sumter Valley, Ore., in 1916, he was elected to membership in the American Institute of Mining and Metallurgical Engineers. During the same year, he was married to Miss Grace Wells, of Arkadelphia, Ark., and besides his widow leaves a young son. In Hubert I. Ellis, there was found the rare combination of executive, administrative, and business ability, together with a temperament exceptionally well adapted and trained for research work and for the careful and exhaustive examination of engineering problems, both practical, and academic. These qualities were in addition to a splendid physique and a personality that made him highly successful in the handling of sub-ordinates and in his contact with his associates and the public.

Jan 4, 1919

By Raymond Mancha

TO determine the optimum inside dimension of an airshaft, it is necessary to strike the proper balance between the cost of power for air friction and turbulence losses within the airshaft, on the one hand, and the cost of sinking the airshaft, on the other. An airshaft larger than necessary is extravagant because the increased amortization rate exceeds the reduction in power cost. Conversely, an airshaft smaller than is needed wastes more power than can be justified by the corresponding reduction in amortization rate. The airshaft power is a function of the air volume Q cu. ft. per min. and the air- pressure drop p in. water gauge across the airshaft The airshaft pressure drop is calculated by the formula: [ ] wherein R is the air-friction coefficient for the portion of the airshaft 1 ft. deep, 0 ft. in perimeter and A sq. ft. in area, when passing an air volume of Q cu. ft. per minute. The airpower w kw. dissipated within the airshaft is computed by the formula: [ ] With a combined over-all unit efficiency of the fan and drive of E per cent, the air- shaft power requirements become [ ] There are 8760 hours per year, so with energy at I cent per kilowatt-hour the annual cost per kilowatt for continuous operation is $87.60; therefore, with energy at C$ per kw-hr. the annual airshaft power cost MI dollars per year becomes: [ ] which, expressed by the component parts, becomes : [] The amortization rate a dollars per year per dollar invested includes both depreciation and interest on the investment. These in turn involve the expected useful life of the airshaft and available monetary interest rate. For the purpose of this discussion the cost of airshaft sinking is assumed to comprise a fixed move-in charge Y dollars, which covers the cost of transporting, erecting and removing the shaft-sinking equipment and is independent of the air- shaft size. Also, it is assumed that the cost of shaft lining, if any, is fixed at $X per cu. yd. of lining material and that excava-

Jan 1, 1946

By R. F. Mehl, W. Batz, C. Wells

L. S. Darken—It is indeed gratifying to find that the results of the two different methods here reported are in substantial agreement with each other and with the earlier work1 of two of the authors. Dr. R. P. Smith, of our laboratory, has been conducting some experiments at 1000°C to determine the diffusivity of carbon in austenite by a third method— the steady state method. This work, which will soon be reported, is far enough advanced that we can say it is in substantial agreement with that of the present authors. The only disparity which might be considered significant is in the high-carbon region, where we find that the diffusivity rises a little less steeply than indicated in fig. 8. F. E. Harris—The authors have presented an impressive arrangement of data concerning the diffusion of carbon in austenite. Of particular interest is the compilation, table IV, which is repeated in col. B of table V for direct comparison with values (col. A. table V) from a formulation using a single Q value of 31,000 cal as the activation energy for diffusion. This comparatively simple formulation has been used quite successfully in the practical application of calculating the carbon added (or removed) through the face in carburizing and decarburizing experiments, where the face concentrations are held quite constant for known times and temperatures. Literally hundreds of tests have been so checked where the computed and experimental values have varied by less than 5 pct. For higher temperatures, where proper carburizing data are hard to obtain, the diffusion couple is treated as a decarburization of the high-concentration bar and as a carburization of the low-carbon member. The analysis has been limited to a maximum of 1.40 wt pct carbon. The agreement between cols. A and B in table V may be considered fair, if a liberal viewpoint is taken. The use of a diffusion couple has one serious drawback, in that comparatively small amounts of carbon pass through planes of concentration close to those of the initial high-carbon and low-carbon members, and hence small errors become important. In addition to the sensitivity at these high and low concentrations.

Jan 1, 1951

EVERY intelligent and practical investigator of minerals says that copper ore is found in various regions of the world and that among others Italy is very rich in it. But very little is mined there, perhaps because of a cowardly Italian avarice which has the power to make us lazy and indolent in carrying out those lofty and fine designs which should reasonably make us proceed swiftly, or perhaps because we are not prone to attempt extraordinary profit but only undertake those enterprises in which we are certain of a return on our investment. The reason for this might also be found in the meager possibility of success, which, since these things are not easily attempted because they are enormous undertakings of doubtful outcome, cools the spirit of men and in place of enthusiasm introduces the fear of loss, the fear of having to sacrifice not only time but also the work and money invested; then they think of the difficulty [II] of discovery, of the impossibility of full ownership, and of the necessity of excavating the mineral marrow from the hardest bones of the mountains with the brawn and efforts of men. To this is added the fear common to many that in attempting such things they may be called fools by certain ignorant and dissolute persons, and it seems better to them to be praised for becoming rich through usury and by many other infamous and illicit methods than to lay themselves open to the danger of censure from such as these. But there are those who deserve still greater censure, particularly princes and all rich and powerful persons, and theirs is an even more useless error than that of those who refrain for the above reasons. If the occasion and means present themselves for both attempting and continuing such a profitable and laudable affair as mining ores and if they hesitate solely because of cowardice or because they give ear to the bayings of ignorant hounds, or if because of their own willfulness they wish to remain prisoners of a detestable and ugly avarice, then this is their own loss.

Jan 1, 1942

AT THE beginning of February the British Government announced acceptance of the American terms for funding the war debt, the main features-being as follows: Interest rate of 3 per cent. for the first 10 years and then 3 ½ per cent. up to the final extinguishment of the debt at the end of 62 years. The interest from the time since the loans were made to the actual beginning of the funding arrangement to be recomputed at 4 1/4 per cent. instead of the 5 per cent. rate now in effect. Congress ratified the contract respecting the British debt. The ship subsidy bill was relegated to the rear, which is indeed an end to the project. The natural consequence of this will be a liquidation of the Govern-ment's shipping business. The joint committee on the reorganization of Govern-ment departments made its report to the President. In general this seems to offer a well-considered plan for the coordination of Government service. The pro-posals respecting the bureaus that are particularly associated with the mining industry may be subject to criticism. According to the committee's plan, the Geological Survey remains in the Department of the Interior, but the Bureau of Mines and the compilation of the statistics of mineral production are transferred to the Department of Commerce. The Lausanne conference among the European powers came to an end early in February, without any treaty having been signed, owing to the refusal of the Turks to accept the ultimatum of the Allies. Theoreti-cally this left conditions in a state-of war between the Allies and Turkey. However, no actual movements have resulted. The French and Belgians continued to hold the Ruhr district of Westphalia, extending their lines and administration of the region. The Germans adhered to the policy of passive resistance. In the Parliament of Great Britain the French and Belgian policy was plainly declared to be unwise and dangerous. French and Belgian industries, moreover, were troubled by strikes among their own coal miners for higher wages. The Poles and Lithuanians engaged in border war-fare;. the civil war in Ireland continued. The rest of the world was quiet insofar as military operations are concerned.

Jan 2, 1923

By R. S. Shrode

By now most readers of this column are aware that it no longer has a regular editor. Tom Murphy, who did the job so well, has had to bow out because of his duties in Australia---duties that keep him from the luxuries of such things as typists and typewriters for rather extended periods of time. We will miss his regular contributions but hope and expect to hear from him as a guest columnist from time to time. Finding an editor to function on a regular basis turns out to be no simple task. This does not mean that there may not be candidates around who would secretly enjoy having their arm twisted into a "yes" position, but at the moment none has been found. Anyway, at the Salt Lake City business meeting it was agreed that we should try to spread the load around. To that end, the Regional Vice Chairmen were specifically singled out as one potential source of contributions. These fellows should have an opportunity for a hearing during their term in office. The existing organizational set-up of the IndMD Division may be a little unfair to this group of officers. The limited responsibility outlined in our Manual of Official Duties and Responsibilities does not offer them much chance for self-expression. Probably the by-laws were written so as to have a geographic representation of membership in case it should be needed at some time. But that is another subject. The point is that now these regional officers have an opportunity to speak out on topics of their own choosing through this column. Some have already done just that. There are also other potential contributors to the column. One is the Secretary, who twice a year uses the column for distributing the minutes of our business meeting to the members. Another is the outgoing Division Chairman. In Salt Lake City, it was decided that this officer should be challenged to contribute something each year as a means of reviewing events of the past year or explaining what should have happened but didn't. I am, therefore, trying to accept that challenge.

Jan 1, 1970

PAUL. D. MERICA, Bayonne, N. J. (written discussion*)..-The mode of intercrystalline oxidation which the authors" have so well observed and described is characteristic of nickel that has been exposed' to: the action of an oxidizing atmosphere at higher temperatures, such as, those at which; it is annealed or heated for rolling or forging. Oxidation under such conditions proceeds inward from the surface along the, crystal boundaries' producing a net-work, probably of oxide; which causes a very brittle condition of this surface material. This, in turn, generally results in surface cracking and checking during further, rolling and a defective sheet or other product is produced. An example of this is shown in Fig. 2, which shows the surface, of a badly surface-cracked sheet of nickel produced by incorrect heating con-ditions. A cross-section of this sheet etched with nitric acid is shown in Fig. 1, which reveals the intercrystalline oxidation network adjacent to both surfaces.These layers are so brittle that it is not possible to deform them by rolling without severe cracking along these lines or, planes of weakness. The best, and possibly only, remedy for this condition lies in its prevention by the maintenance of a neutral soft flame for heating and annealing nickel during the entire course of its manufacture. I should like to suggest that, those making microscopic investigations of nickel and nickel-rich alloys try the use of acetic-acid .solutions of nitric acid for etching these metals rather than aqueous solutions, of nitric acid. I have found that a solution containing 50 per cent. nitric acid, from 25-45 -per. cent. acetic acid, and from 25-5 per cent. water gives excellent results with. Wrought and cast nickel and Morsel metal and superior results to those obtained with nitric acid, alone. The acetic. acid seems to inhibit the passivity that nickel often assumes toward nitric acid and much more uniform etching may, be obtained. The proportions of nitric and acetic, acid may be varied somewhat from those given without mate-rially altering the quality of the etching, although without any distinct improvement in it.

Jan 12, 1919

By George H. Ashley

Mining, including quarrying, dates back almost to the dawn of history, beginning almost with the beginning of what we call civilization. State surveys date back about 100 years. Evidently mining flourished for thousands of years before state surveys were thought of. Why should it not continue to flourish without state surveys? First, it may be noted that as mining and civilization were contemporaneous, so state surveys and the science of geology were almost contemporaneous. As recently as 30 years ago the United States mineral laws were interpreted to mean that coal lands in the public domain were only those lands on which workable coal outcropped. The half billion acres of public land underlain by .coal but on which it did not outcrop were treated as homestead lands and open to settlement. Just what did the science of geology do to or for the mining industry? Until geology arose rocks or minerals or ores were where they were found. Their finding might be accidental, or might be the result of deliberate search or prospecting. In open, rocky country, with little or no vegetation, as in parts of the West, prospecting served very well, though at an enormous expenditure of human time and effort, if not money. The old saying that every dollar's worth of gold taken from the earth has cost two dollars may largely be charged to the time value of the usual method of prospecting. Geology changed all that. The science is still young and it still labors under handicaps of immaturity and early errors. Geology, however, has gradually been discovering the relations and conditions under which the several mineral deposits occur. Its elaborate studies of exhausted or nearly exhausted mineral deposits has done for it what human autopsy has done for medicine and surgery. Perhaps in no field is this plainer than in the oil and gas industry. Note might also be made of several important coal fields in England and on the Continent, in which the coal is everywhere deeply buried. Passing over the long period of growth during the past 100 years, geology today is prepared to offer the mining industry: first, a knowledge of the geologic conditions under which most minerals occur and to explore

Jan 1, 1935

By C. R. Dodson, W. T. Cardwell

This paper presents the results of a theoretical and experimental study of the effect of preperforated liners on well productivity. The analysis concerns the rectangular type of slot, either machine or torch cut, which is common in California. Muskatla treated this problem recently in a mathematical analysis of the flow of oil or gas from natural reservoirs into both gun-perforated and slotted liners. This paper presents additional and simplified analytical considerations and conclusions for the slotted liner, the solutions being applicable in the laboratory as well as in the field. An application of the analytical methods to permeability measurements on mounted core samples is given, to show the effects of sealing wax or other obstructions on the end faces of the cores. Results Fig. I 'Ompares the results of some theoretical calculations with the results of electrical analogy experiments performed in the Standard Oil Company of California's Production Technology Laboratory at La Habra, California. Fig. I indicates that the flux into short, "three-dimensional slots" of the relative dimensions encountered in practice is approximately equal to that into full-length, "two-dimensional slots" having the same open fraction of pipe. (The same numbers of slot rows, and the same radius ratio are also implied.) It can be seen from physical considerations that the closeness of this approximation must improve as the ratio of the external radius to the internal radius increases. Therefore, it is possible to calculate the flow into a slotted liner using a simple modification of the Darcy equation: where N is .the number of slot rows and O is the open fraction of the pipe. Fig. 2 shows the results of calculations . using Eq. 28. The most remarkable features of Fig. 2 are the high flux values for very small open fractions of pipe. For instance, with six slot rows and a radius ratio of 500, 74 per cent of the open-hole flux may be obtained with only o.I per cent of pipe Open. Fig. 2 shows that for a given open frac tion of pipe, the flux is greater, the greater

Jan 1, 1945