Search Documents

By P. W. Neurath, R. E. Waite

INFORMATION is available on the effect of stress on permeability, coercive force, and hysteresis for a variety of materials' but for the technically important grain-oriented 3 pct Si-Fe' the stress effects are not adequately covered in the literature; in addition, most of the stress data do not permit estimation of what would happen to the 60 cycle watt losses of the material under stress. Direct measurement of these effects therefore has been made and appears to be of considerable theoretical as well as practical interest. Losses were measured on the central 25 cm portion of 40~3~0.035 cm samples which could be stressed in a small tensile machine built for this purpose. Under tension the following effects, illustrated in the figures by a particular example, were observed: 1—"Unstrained" material of commercially acceptable loss level shows no change or a small increase in loss at low elastic stresses. For the sample shown in the figures, this is illustrated during the initial run, where a 7 pct increase is observed (Fig. 1). 2—There is no additional change in loss when the sample is further strained up to the elastic limit (Fig. 1). Within that limit the loss-stress curve is reversible. This is not illustrated in Fig. 1. 3—Even in the plastic range only small increases in loss are observed as long as the sample is kept under stress (Fig. 2, point N); often no increase can be observed (Fig. 1). 4—A large increase in watt losses is observed after removal of the stress subsequent to plastic deformation (Figs. 1 and 2). 5—All, or nearly all, of the foregoing increase in loss due to plastic deformation can be eliminated by a reapplication of tensile stress but returns upon removal of this stress. This is illustrated in the third run (Fig. 3). This run remains within the elastic limit and shows the reversibility of the stress-loss curve under this condition. These findings have been confirmed on large Samples (approximately 200~10~0.035 cm and larger) except that under 1 no initial increase in loss was ever observed on these. The accuracy of the watt loss measurements is of the order of 1 pct. Neither bending of the sample in the tensioning device nor a redistribution of flux along the width of the sample accounts for these results. They therefore must be explained on the basis of either a change in the domain configuration due to stress or a change in the domain wall mobility. Acknowledgment The assistance of Mr. Robert L. TenBroeck with the instrumentation is gratefully acknowledged.

Jan 1, 1956

By W. H. HOWARD

Discussion of the paper of W. H. HOWARD, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 2029 to 2046. EDGAR M. DUNN, Anaconda, Mont.-Mr. Howard's contribution to the literature on the Cottrell, method. of electrostatic precipitation of flue dust and fume at Garfield has been read by us with peculiar interest for the reason that we have been experimenting with the same process at Anaconda for the past eight or nine months, with a view to adapting it, under the direction of Dr. Cottrell and the supervision of J. 0. Elton. and D. R. Kellogg, representing the Anaconda Smelter Commission, to the treatment of very large volumes of gases, using large pipe treaters and various forms of electrodes, with about 150,000 volts rectified current. For the amount of gas to be treated here the 5-in. pipe means a cost for installation that is practically prohibitive, clue to the tremendous number of pipes required, and we have been trying to cut installation costs by increasing the size of the pipes. All of our work is still in the experimental stage, but we have obtained good clearance on our mixed roaster and converter gases with a 3-ft. pipe treater 20 ft. long, and with 5 ft. velocity therein; and with a discharge electrode of a single No. 29 nichrome wire set in the middle of the 3-ft. pipe, with. a consequent electrode spacing of 18 in. The current used has been 150,000 to -160,000 volts, .and of course there have been troubles galore, relating particularly to insulation and rectifying. Blast-furnace gases did not give so good clearance, probably due to relative poverty in moisture and S03 content of blast gases to roaster-converter gases; making the blast gases the poorer in conductivity. Our experience has been so satisfactory that in our next experimental plant-built on a somewhat larger scale-we shall attempt a 4-ft. treater with greater electrode spacing, and a somewhat higher voltage-up to 220,000. As to fractional precipitation, mentioned by Mr. Howard, this idea was tried out at Anaconda last year (1913). Formerly our furnaces (Bruntons) roasting flue dust for the recovery of white arsenic, passed so great an, amount of dust to the settling kitchens that refining of this arsenical product was necessary to eliminate the 5 to 20 per cent. dust contained therein. Consequently the manufacture of As203 was effected in two stages, with a reverberatory roast of the first .product to obtain the final 99.5 per cent. As203. -

Jan 11, 1914

By D. S. Hutton, W. C. Leslie

Thermal etch patterns developed on poly crystalline 3.5 pct Si-Fe by heating in hydrogen or in argon have been examined. The most prominent feature of the etching is the development of striations on grains with (100) planes near the plane of the surface. These striations are probably produced by the resoution of a random, high-energy plane into (100) facets of lower energy. THE thermal etching of iron and iron-base alloys has a long history. The phenomenon was observed by Osmondl more than 70 years ago. The literature on thermal etching between that time and 1951 was reviewed by Olney,2 and a briefer review appeared in 1958. 3 The only articles which have been found dealing with the thermal etching of silicon iron are those of Dunn and Lionetti4 and of Dunn, Daniels, and Bolton,5 and they reported only grain boundary etching. EXPERIMENTAL PROCEDURES A cast 3.5 pet Si-Fe alloy was given a metallo-graphic polish and etch, then placed in flowing purified hydrogen for 6 hr at 2200°F. The same specimen was later repolished and etched to remove the thermal etching. The specimen was then held in flowing purified argon at 2200°F for 72 hr. In both instances the specimen was rapidly cooled by being pulled up quickly into the cold zone of the furnace. All photomicrographs shown are of the surface as removed from the furnace. Oblique illumination was essential for observation of the thermal-etching effects with a light microscope and was used for all the photomicrographs. RESULTS AND DISCUSSION Grain boundary etching, grain boundary movement, and contouring within grains are illustrated in Fig. 1. The contours within a single grain followed behind the advancing grain boundary. To determine the average contour interval, or step height, white light was used in an interference microscope. The steps were of the correct magnitude to separate while light into its spectrum of colors. A green light was focused at the top of a contoured area, shifting to red across the field. By using the difference in the dominant wave length of red and green light,6 and counting the number of steps across the area, it was possible to obtain a value of about 80A for the average step height. Laue back-reflection patterns of four grains with contour lines showed that the grains had a (100) plane slightly inclined to the plane of the surface (± 5 deg). Insofar as this could be determined from their irregular traces, the contour lines within a grain had a common direction, <100> ± 5 deg.

Jan 1, 1961

HAVING previously told you about lodestone, azure, emery, and manganese, things that perhaps belong more properly to the stones than to the metals, the desire has come to me to describe rock crystal as well and, with this, some of the better-known gems, although they are things that are not classified with metals, as far as I know, or even with the serniminerals. In truth, they are neither one nor the other, but they are stones and have the nature of stones. But let them be what they may, in order to avoid straying from the subject we have begun, we shall say that they have mineral properties in their species, as for instance, in respect to their colors. It would seem an error to me if, while I am giving you information on so many other useful things, I did not give you this as well, if for no other reason than because it is a fine accomplishment for a gentleman to have some knowledge concerning gems. Thus since I have proposed to do this, beginning to speak of crystal, I tell you that it is a lustrous, transparent, and limpid stone, composed by Nature with a predominance of wateriness. Thus, contrary to the order of natural things, it has been believed by many that Nature has generated it of pure water by means of a powerful and continuous coldness that always exists in those mountains and places where it is found, for the waters and snows can never melt there because of the great cold. They have tried to prove this opinion of theirs by saying that crystal still retains the nature of frozen water, and that this is. shown not only in its appearance but also in the fact that, like ice, it floats without sinking to the bottom when it is put in water. They also say that it is customary to put it under the tongues of the thirsty on account of the, coldness and moistness which it gives, and that it quenches the dryness of their thirst. But even if all these things were true, as they are not, they do not upon consideration bring us to the conclusion that it is water, because the diamond and the beryl would do the same. Therefore it does not seem to me credible [391 that it is as they claim, for it is a stone generated as such by Nature. And then, if this were true in those places where it rains often and many snows are formed, and these should freeze and never melt but

Jan 1, 1942

By Harlan W. Nelson, James B. Purdy

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the underfeed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention. Some twelve years ago a laboratory method was developed at Battelle Memorial Institute for the relative evaluation of coals for use in residential underfeed stokers. The method was developed in conjunction with work being done at that time for Bituminous Coal Research, Inc., and for individual coal producers, to obtain information on the characteristics of coal that determined the successful performance of the small stoker. Details of the equipment and test procedure were given by R. A. Sherman1 in a paper presented at the University of Illinois Fifth Short Course in Coal Utilization. During the past several years, the evaluation of over forty different coals has been determined by investigations sponsored at Battelle by coal operators in the eastern producing districts. The purpose of this paper is to compare the results and conclusions derived from the various tests with marketing experiences of the operators, and to discuss briefly the relationship of test results to standard laboratory determinations. Equipment Used in Tests Fig 1 shows schematically the equipment used in the evaluation tests. The stoker is a commercial model of conventional design, having a nominal feed rate of 30 Ib per hr. A special laboratory furnace is used, which is tightly sealed to prevent the entrance of secondary air. The complete stoker-furnace assembly is mounted on platform scales which permits the measurement of combustible weight losses occurring during the test. The furnace stack, in which are a thermocouple, flue-gas sampling tube, and smoke meter, is connected to the laboratory exhaust breeching through a friction-less connection. Through use of an auxiliary blower system, provision is made for the measurement of the air delivered by the stoker fan to the windbox. A water seal in the duct work eliminates inter-

Jan 1, 1950

By Brison Robertson, W. P. Fishel

The carbide-forming tendencies of the various steel-alloying elements, or their affinities for carbon, is a subject that has received considerable attention, but little more than a probable arrangement of the elements as to their carbide-forming tendencies has been proposed. The physical properties of alloy steels depend upon the relative proportions of the elements present and their combinations. one important phase of this subject is the distribution of carbon between the various elements present. The distribution of car. bon between iron and other elements evidently sill depend upon: (I) the affinity of each for carbon; (2) the relative atomic masses of the elements present; and (3) the possible formation of compounds between the alloying and iron and between the elements themselves, In ternary steels the case is simplified, especially in systems in which the element and iron form no compounds, In such systems iron and the alloying element are competing for the carbon present. In this work the distribution of carbon between titanium and iron has been studied by measuring the relative amounts of iron carbide and titanium carbide present ill a series of annealed steels in which the ratio of titanium to carbon extended from 0.527 to 4.61. Ten Fe-Ti-C alloys, weighing about 250 grams each, were prepared by melting under a Vacuum, in an Induction furnace, Armco iron, carbon-free ferrotitanium (25 per cent Ti), and pure carbon. Vacuum melting prevented the formation of titanium oxides and nitrides, which would the the problem. The melts were made in graphite crucibles lined with sintered magnesium oxide. The ingots were the in the furnace under a vacuum and "&apos;ere then completely annealed at 950°C. The determination of the amount of titanium carbide present was based upon the established insolubility of titanium carbide in boiling dilute (1:4) sulphuric acid, and the complete solubility Of free titanium and titanium-iron compounds in this acid. High-carbon ferrotitanium, which had been treated to remove free Ti and Fe. was found to be completely insoluble in the acid; and the carbon-free ferrotitanium used in making the alloys was found to be completely soluble. Others have reported the insolubility of titanium carbide in sulphuric and hydrochloric acids. Turnings from the ingots were digested with boiling sulphuric acid (1:4) until all action had ceased. The carbide residue was filtered off and analyzed for titanium, and in some cases for carbon. This represerifs the titanium that was united with carbon The filtrate from the carbide residue contains the portion Of the titanium that was in solid solution in the ferrite. Titanium

Jan 1, 1945

Ware B. Gay, Richmond, Va.: Having followed the remarks of Prof. Woodworth with great interest, especially his suggestions for drilling in the part of the coal-field on the south side of the James river, I would like to inquire of him if he reached his conclusions after fully considering the situation as existing upon the north side of the James ? My reason for this inquiry is, that upon the north side the eastern and western outcrops are much nearer each other than appears to me to be the case upon the south side, and also that the western outcrop on the north side is much more clearly defined than upon the south side. It is now about twelve years since I first became interested in the Richmond coal-field—and until about six years ago I passed much time in investigation and spent thousands of dollars in developments. About six years ago the properties in which I was more especially interested were leased to other parties, and since that time I have had little or nothing to do with the mining operations. I regret to say the price of coals has ruled so low during most of the time since the lease was made that the developments have not been as extensive as the lessees had originally intended. The result of my investigations after considering all the theories, expert reports, legends and other information I could obtain bearing upon the subject, was the opinion, which I still hold, that the most practicable and most economical way for proving the extent and value of the field is by sinking slopes from the eastern outcrop, and by prosecuting such slopes in the vein and following the coal to the western outcrop, thus obtaining an actual cross-section in fact and not in theory. Proceeding upon this hypothesis, I sought for the positions where this could probably be accomplished most quickly and develop a marketable coal-area as the work thus progressed. The outcrops on the north side being nearer each other, and

Jan 1, 1902

Mr. A. Bement, Chicago, Ill. (communication to the Secretary*) :—Mr. Campbell, in proposing his method of sampling coal-seams, has rendered an important service in insisting on the presentation of an adequate history of the sample; and it is to be hoped that his suggestion will meet with further recommendation. In my opinion it is fully as important that a complete description of the sample and the conditions surrounding its taking be given, as the results of the analysis itself; and if such should become standard practice, coal-analysis would assume greater value. As it is, the published data are very confusing, and only to an extremely small extent are they really useful. The method suggested by Mr. Campbell, however, cannot have a general application; for example, in the Eastern Interior coal-basin, particularly at the present time, the output consists largely in grades other than mine-run, which in Illinois, for the year 1905, was only about 24 per cent. of the total product; and inasmuch as Mr. Campbell&apos;s method of sampling cannot give values for any other grade than mine-run, my contention that, at best, it can have but a limited application, is apparent. To illustrate the argument, there are two coal-seams, with the characteristics of which I am particularly familiar; each seam, as it lies in the ground, contains almost exactly 10 per cent. of ash; the lump coal from one of these seams ranges from 10 to 11 per cent. of ash, but from the other seam it does not average more than 6 per cent., although, as before mentioned, the average percentage of ash in the full seam is the same for each case. A careful and proper sampling of coal-seams, to be followed by analyeis, is to be commended in connection with all investigation; in fact, it should precede any careful study. A serious error, however, may be made in attempting to use such results to set values on the product as shipped or received. The only

Jan 1, 1906

By R. H. SWEETSERS

A Discussion of Mr. Hall&apos;s paper, read at the Washington Meeting, February, 1905. R. H. SWEETSER, Sault Ste. Marie, Ont. (communication to the Secretary*) :-The recent work of furnace No. 1 of The Algoma Steel Co., at Sault Ste. Marie, Ontario, using for fuel, first all charcoal, then a mixture of charcoal and coke, and finally all coke, upsets the estimates given by Mr. Hall in the last two paragraphs of his interesting paper. Furnace No. 1 was built for a charcoal-furnace, and it was run on charcoal fuel from March 6 until July 9, 1905; then, for a week, a mix¬ture of charcoal and coke was used, and, since then, coke alone has been the only fuel. It is to be regretted that at no time, during the run on charcoal, was there enough charcoal on hand and " in sight&apos;" to warrant blowing the furnace as hard as it should have been blown. During April and May the supply of charcoal limited the amount of blast to about 8,000 cu. ft. of air per min.; in June, to about 8,900 cubic feet. For a few days in July about 10,000 cu. ft. were blown, and then the maximum daily output, 173 tons (2,240 1b.), was reached. At all times the quality of the charcoal was poor, having been made from wood cut from three to four years before. Doubtless this furnace could have produced .200 tons of iron per day, even with this quality of charcoal, provided the supply had been sufficient; and with good charcoal I see no reason why it could not make as much iron per day as it has made with coke. During the one week of using a mixture of charcoal and coke, the changes in quantity of blast and composition of the slag followed each other so closely that no single condition could last long on the furnace. The results were good, and the pig-iron was about the same in quality as that made during the

Jan 1, 1906

By Nico Van Wingen

Experiments performed with distilled water, unconsolidated sand and dead oil for the purpose of determining the influence of oil flow on the water content of sands were described. While results found are not necessarily, therefore, identical with those that would be obtained under natural petroleum reservoir conditions, the following conclusions were drawn. 1. When oil under constant head is flowed through an unconsolidated sand, the amount of water retained in the core is inversely proportional to the specific permeability of the core. This corroborates the view that the degree to which oil displaces water out of the pore space is limited by the size of the pores. 2. For the range investigated, the displacing action of a more viscous oil of higher specific gravity was found to be the same as a less viscous oil, or lower specific gravity. 3. The amount of interstitial water retained in the sand bears an inverse relationship to the pressure head of the displacing liquid. 4. The degree of retained water saturation of the sand appears to approach 100 per cent as the specific permeability approaches zero. 5. For the higher values of specific permeability and for the pressure range investigated the remaining amount of water in the sand occupies approximately 10 per cent of the pore space. This, together with the fact that the limiting oil velocity curve approaches approximately 10 per cent water saturation as an asymptote, indicates that beyond this point removal of water is achieved only by a stripping of the grains requiring considerable pressure drops across the sands; or by a balancing of the molecular forces. 6. As the water saturation of the sand exceeds approximately 15 per cent of the pore volume, the permeability of the sand to oil decreases rapidly. 7. Sands with water saturations as high as 40 per cent were found to produce 100 per cent oil.

Jan 1, 1939

By Nico Van Wingen

Experiments performed with distilled water, unconsolidated sand and dead oil for the purpose of determining the influence of oil flow on the water content of sands were described. While results found are not necessarily, therefore, identical with those that would be obtained under natural petroleum reservoir conditions, the following conclusions were drawn. 1. When oil under constant head is flowed through an unconsolidated sand, the amount of water retained in the core is inversely proportional to the specific permeability of the core. This corroborates the view that the degree to which oil displaces water out of the pore space is limited by the size of the pores. 2. For the range investigated, the displacing action of a more viscous oil of higher specific gravity was found to be the same as a less viscous oil, or lower specific gravity. 3. The amount of interstitial water retained in the sand bears an inverse relationship to the pressure head of the displacing liquid. 4. The degree of retained water saturation of the sand appears to approach 100 per cent as the specific permeability approaches zero. 5. For the higher values of specific permeability and for the pressure range investigated the remaining amount of water in the sand occupies approximately 10 per cent of the pore space. This, together with the fact that the limiting oil velocity curve approaches approximately 10 per cent water saturation as an asymptote, indicates that beyond this point removal of water is achieved only by a stripping of the grains requiring considerable pressure drops across the sands; or by a balancing of the molecular forces. 6. As the water saturation of the sand exceeds approximately 15 per cent of the pore volume, the permeability of the sand to oil decreases rapidly. 7. Sands with water saturations as high as 40 per cent were found to produce 100 per cent oil.

Jan 1, 1939

By Arthur C. Simmons

Oil production and activity in northern and central Pennsylvania was slightly less in 1939 than in the previous year, but owing to higher average prices 1939 was undoubtedly a better business year. The last quarter showed markedly increased activities throughout all of the Pennsylvania fields. Production, Stocks and Price Storage of Pennsylvania crude oil at pipe lines and refineries totaled 5,413,000 bbl. on Dec. 31, 1938, and declined during the year 1,124,000 bbl. to a total of 4,319,000 bbl. at the end of 1939. The stocks of crude at the end of the year represent the lowest point reached in Pennsylvania-grade crude storage in recent years. Stocks increased slightly during April, May and June, but decreased during all other months of 1939. The Bradford field production within the state of Pennsylvania averaged 35,340 bbl. per day throughout 1939, which represents a decrease of 1419 bbl. a day from the 1938 average. The production in central and southern Pennsylvania increased 1176 bbl. per day, averaging 12,159 bbl. throughout 1939. Table 1 includes annual production for the part of Bradford field situated within the state of Pennsylvania, for central and southern Pennsylvania, and for the entire state of Pennsylvania. A definite segregation of production between the Bradford field and central and southern Pennsylvania is slightly ambiguous because a portion of the oil from the newly discovered Music Mountain pool is included statistically in each area. In all probability the entire increase and some small addition to the production from southern Pennsylvania can be attributed to oil produced from the Music Mountain pool. Within the Bradford field, six price changes occurred throughout the year. At the beginning of 1939 the price of Bradford crude oil was $1.80 per barrel, whereas by the end of the year it had risen to $2.50. The weighted average price for Bradford crude during 1939 was $2.059 per barrel.

Jan 1, 1940

I. N. KNAPP, Ardmore, Pa. (written discussion*).-The possibility of storing natural gas in the sands f exhausted gas pools might be, in many cases, a, good engineering proposition, but it cannot be considered a practical business proposition tinder the usual competitive leasing and operating conditions that exist in the natural-gas business. Under the usual conditions of diversified land ownership and leasing with all lack of cooperation, various operators drill into the same pool or reservoir and drain out the gas under each other&apos;s land. To attempt to use for storage purposes the depleted sands f any one pool having such various competing ownerships would be highly impractical, considered from operating and business standpoints, unless there was cooperation with the interests owning adjacent wells and leases or the purchase f the same. Also, it would be very difficult to find out whether all old or abandoned wells in any pool had been properly, plugged and thus prevent the waste of gas brought from a distance for storage. Another objection to Mr. Panyity&apos;s proposition is the probability that no lease made in the past contemplated the use of a gas sand for storage purposes. Very likely, then, the operator would have a lawsuit on his hands for the unlawful use of a lease if he attempted the storage f such gas without first obtaining additional lease rights. In some instances salt water could not be pumped from a gas well in the customary way of pumping oil wells on account of the deposition of salt in the pump valves or in the working barrel or tubing. Very ingenious compressed air jets have been devised and arranged with suitable piping to blow out such salt-water accumulations. In many pools it would be impracticable to drill a water pocket below a gas sand, as suggested, since such deeper drilling would probably. intensify water troubles.

Jan 5, 1919

By Myron K. Rodgers

In rock- or ore-crushing tests all data, in order to be valuable for study and comparison, should be obtained and tabulated under conditions as uniform as possible. The results of many such tests have no value for comparison, because of incomplete data and the lack of uniform conditiops, screens and scale of sizing, etc. The purpose of this paper is to suggest a form of standard specifications which may be developed by the Milling Committee and approved by the A. I. M. E. for rock-crushing tests. It is not intended to discuss any theories of rock crushing. Reports of rock-crushing tests should include the following details: 1. Description of the machine employed (jaw or gyratory crushers, rolls, stamps,tube mills, Chilean mills, etc.), 2. Method and material (timber, concrete, etc.) of foundation. Much power is dissipated in the vibration of poor foundations. 3. Locality from which the rock or ore was obtaincd, and geological, mineralogical, and physical characters of the material. 4. The power consumption of the machine running with no load and with full load, the unit of power being 1 hp. per 24 hr, 5. The capacity of the machine in tons (of 2000 Ib.) per 24 hr. 6. The duty in tons per horsepower-day. 7. The screen analysis of feed and product by the proposed A. I. M. E. standard screen scale. On the foregoing statement, the following remarlrs are offered. Toughness of Rock Table P shows the relative crushing duty of the same machine on three different characters of rock, all other crushing conditions being the same. This table indicates that the specific resistance of the rock to crushing, may affect the crushing duty of a unit of power as much as 300 per cent. Perhaps this quality may be called toughness. It is not a function of hardness only. For comparison of tests, rocks should be divided into

Jan 1, 1916

By Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (d) of the liquid-to-solid transfer at each temperature has been derived: d = ZLXL(XL - P) + Zsxs(P- ZL(XL - P) + Zs(P - Xs) where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, XL and xs are the composi-tions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under considera-tion. The d equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid-to-solid transfers if the corresponding equilibrium diagrams are known. The d -versus-temperature curves for two alloys Pl and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid FIG. I.-GENERAL SOLID SOLUTION DIAGRAM SHOWING S CURVES FOR ALLOYS P1 AND P2. phase only at the temperature of the be-ginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate tem-perature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1940

David H. Browne was born June 8, 1864; at Hollymount, County Mayo, Ireland. At the age of 16, after going through the Londonderry Academy; he came to this country, and entered the University of Michigan, where he was graduated in 1885. He began his scientific practice as chemist, under F. A. Emmerton, in the laboratory of the Joliet Steel Co., after which he served some time as chemist at the Ludington mine, Iron Mountain, Mich. But in 1888 he went back for a year to his alma mater as instructor in inorganic analysis. Those who knew him feel sure that he would have been an efficient and popular professor; but his ardent temperament could not brook the rnonotony and confinement of the class- room; and in 1899 he went to work at the Andrews and Hitchcock blast-furnaces, at Hubbard, Ohio, where he remained until 1891, when he entered as chemist the service of the newly organized Canadian Copper Co., operating in the Sudbury district, Canada. This was the beginning of his special professional life-work. For twenty-six years he devoted himself to the numerous and complex problems successively arising in connection with the metallurgical treatment of the nickel-copper ores of Sudbury. One of his notable achievements was the development of an electro-lytic process for the separation of nickel and copper in the ores referred to. This method was successfully employed for several years; but when the Canadian Copper Co. was absorbed by the International Nickel Co., the cheaper Orford process owned by the latter was substituted. . A still more permanently important piece of metallurgical progress credited to Mr. Browne was the successful firing of reverberatory smelting-furnaces with powdered coal-a measure which had been desired, dreamed and attempted by others, but which he was acknowledged as first to put in practice on a large scale. The Engineering and Mining Journal of April 7, 1917, says editorially of this improvement:

Jan 6, 1917

By Warden A. Moller

The Fushun coal-field, now being opened up by the South Manchurian Railway Co., is connected with the main line by a branch, 30 miles long, from Sui Chia Tun, 10 miles south of hlukden, the oapital of Manchuria. The coal-field, which lies on the southern bank of the Hun river, 25 miles east of Xiukden, consists of a long narrow valley, running east and west between hills composed of granitic and volcanic rocks. At the foot of the northern hills, the Hun river flows westward towards the Liao river, which drains the greater part of South Manchuria. At the foot of the southern hills, resting immediately upon volcanic rocks, and overlain by 30 ft. of alluvium, is a thick layer of Tertiary shales, carrying near the base two coal-seams. In many places the lower of these two seams is in immediate contact with volcanic lavas and basalts, the flows of which were evidently both prior and subsequent to the formation of the coal-seams. This contact has practically destroyed the lower seam for commercial purposes. The value of the field lies in the upper seam, which, for a length of nearly 8 miles, varies from 100 to 130 ft. thick. Of this seam, 85 per cent. is good coal. The seam dips to the north conformably with the shales, at angles of from 25 to 30°, and appears to have an uninterrupted dip for about 1.5 miles before being possibly cut oft&apos; by the northern hills. The coal-bearing shales extend east and west for a length of about SO miles, but towards the east the continuity of the seams is broken by intrusive rocks. The coal is of the sub-bituminous variety, low in ash, bright in appearance, and breaks with a conchoidal fracture. It has the usual qualities of Tertiary coal—quick steam-raising and poor stacking qualities. Pieces of resin, varging in size from

Jan 1, 1911

By Arthur C. Simmons

Oil production and activity in northern and central Pennsylvania was slightly less in 1939 than in the previous year, but owing to higher average prices 1939 was undoubtedly a better business year. The last quarter showed markedly increased activities throughout all of the Pennsylvania fields. Production, Stocks and Price Storage of Pennsylvania crude oil at pipe lines and refineries totaled 5,413,000 bbl. on Dec. 31, 1938, and declined during the year 1,124,000 bbl. to a total of 4,319,000 bbl. at the end of 1939. The stocks of crude at the end of the year represent the lowest point reached in Pennsylvania-grade crude storage in recent years. Stocks increased slightly during April, May and June, but decreased during all other months of 1939. The Bradford field production within the state of Pennsylvania averaged 35,340 bbl. per day throughout 1939, which represents a decrease of 1419 bbl. a day from the 1938 average. The production in central and southern Pennsylvania increased 1176 bbl. per day, averaging 12,159 bbl. throughout 1939. Table 1 includes annual production for the part of Bradford field situated within the state of Pennsylvania, for central and southern Pennsylvania, and for the entire state of Pennsylvania. A definite segregation of production between the Bradford field and central and southern Pennsylvania is slightly ambiguous because a portion of the oil from the newly discovered Music Mountain pool is included statistically in each area. In all probability the entire increase and some small addition to the production from southern Pennsylvania can be attributed to oil produced from the Music Mountain pool. Within the Bradford field, six price changes occurred throughout the year. At the beginning of 1939 the price of Bradford crude oil was $1.80 per barrel, whereas by the end of the year it had risen to $2.50. The weighted average price for Bradford crude during 1939 was $2.059 per barrel.

Jan 1, 1940

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc, may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, to¬gether with the names of its president and its secretary, may be published in MINING AND METALLURGY or the DIRECTORY of the Institute. The members of such a society will not be named individually on the membership list of the Institute, but may at any time be proposed for election as associates or junior associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied by suitable testimony as to character and qualifications, will have special weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership. The Affiliated Student Societies receive the following privileges: 1 A copy of MINING AND METALLURGY free; 2. The use of Employment Service; 3. The use of MINING AND METALLURGY for publicity purposes, such as printing notices of their activities, etc ; 4. Assistance in obtaining speakers for their meetings, lists of moving-picture films, etc. To retain the privileges of the Affiliated Student Society, its officers must keep in touch with the Secretary of the Institute and advise him of its activities. The foregoing plan is not confined to students in mining engi¬neering or metallurgy. Any undergraduate society of engineers may avail itself of the privileges offered. Societies desiring to be recognized as Affiliated Student Societies are requested to make application to the Secretary of the Institute, giving particulars as to their nature, membership and officers. The accompanying list gives the names of the Affiliated Student Societies as of April 15, 1927, and their presidents and secretaries, in so far as they have been reported to the Secretary of the Insti¬tute.

Jan 1, 1923

By Courtenay DeKalb

The accompanying illustrations, Figs. 1 to 6, from plans drawn by Mr. T. L. Knapp, a student in the Missouri School of Mines, show a type of furnace designed by the writer, which possesses some peculiarities intended to meet the necessities of laboratory-instruction in that institution. The object aimed at was the construction of a simple, inexpensive furnace, suitable for the distillation of zinc from its ores, and using only a single retort. This limitation imposed the chief difficulty, owing to the necessity of obtaining a high degree of heat concentra ted upon the retort. This is accomplished by the peculiar curve of the arch, which consists of arcs of seven distinct ellipses, one focus of each of which lies within the area occupied by the retort. Thus the reflected heat would necessarily be thrown mainly where most needed, namely, on the retort. Conservation of heat is provided for by a return-flue through the hollow arch, and by a sand bottom under the fire-brick hearth. Four openings lead back from the laboratory, or heating-chamber in this instance, to the arch-flue; and three openings lead from the arch-flue to a large horizontal flue, from which a down-take conducts the gases to the stack. The fire box, it dl be observed, is deep, thus producing much CO during the combustion of the coal. The further combustion of this CO may be accomplished by the admission of air through the hollow fire-bridge, thus producing a higher flametemperature surrounding the retort. Provision is also made for removing the retort and the portion of the wall supporting it and the condenser, leaving a high arch, into which a door-frame may be inserted; the space above being temporarily bricked in. By this alteration, which may be quickly and easily made, the furnace may be converted into a reverberatory, suitable for treating small charges such as

Jan 1, 1898