Search Documents

By J. L. Lummus, Frank O. Jones

A field procedure for determining graphite in drilling mud is presented which is sensitive to 0.25 lbs/bbl and accurate to 20 per cent. The method, utilizing oil flotation principles, is suitable for use in all oil-free water base muds except those containing ligno-sulfonates, lignites, or surface active agents. INTRODUCTION Graphite was proposed as a drilling lubricant as early as 1940, but has not been used extensively until recently.' Graphite has been substituted for oil in certain instances to avoid oil contamination of core samples since it has been found that graphite does not interfere with routine core analysis. A major difficulty in using graphite is the lack of a satisfactory field test for determining the concentration of graphite in mud. DISCUSSION OF METHOD Several possible methods of analysis were investigated, including chemical separation, density fractionation, radioactive tracers, and oil flotation.', ' The investigation indicated that a satisfactory method for field use could be devised using an oil flotation method. It was found that toluene shaken with a highly diluted mud sample would recover sufficient graphite to be apparent in the oil phase. Refinement and standardization of technique made it possible to detect as little as 0.25 lb/bbl graphite and to estimate graphite content to within 20 per cent by using a visual comparison method. The test is limited to oil-free water base muds. Quebracho, phosphates, or barytes in the mud do not interfere with the test but surface active agents, lignosulfonates' and lignites evidently render !he graphite water-wet so that none may be recovered by oil-flotation. PROCEDURE Instructions for determining graphite in mud: 1. Collect representative one gallon sample.- from mud stream. Transfer immediately 350 ml portions of this Sample into four mixing cans labeled A, B, C, and D. Measure out graphite (same as is used to treat mud) for addition to cans as indicated below, using either a specially designed scoop or a balance. Can: A B C D Grams Graphite to Add: none 2 4 6 Stir samples B, C, and D for 15 minutes with propeller type mixer. 2. Clean and rinse well with water four 250 ml volumetric flasks labeled I, 11, 111, and IV. Using a 5 ml hypodermic syringe, transfer the indicated volume of samples from cans A, B, C, and D into designated flasks as follows: From Can: A B C D To Flask: I II III IV Add This Volume of Mud: 4 ml 2 ml 2 ml 2 ml 3. Measure 100 ml fresh or distilled water to each flask and swirl gently to disperse mud. Add exactly 5 ml toluene to each flask. Stopper and shake each

Jan 1, 1953

By Harry H. Power

WHILE the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the product is found wanting, the one most responsible should be apprehended. FITNESS FOR PROFESSION For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Many of them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of noncollege grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more interested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more empha¬sis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been made of the beneficial results to be obtained by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

Discussion of the paper of GEORGE S. Rice, presented. at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2459 to 2492. WILLIAM GRIFFITH, Scranton, Pa.-I notice in the discussions and literature that emphasis is placed on rock dust, shale dust, and limestone dust, and I infer that these different. sorts of rock are ground up to produce this dust. -Is that right? MR. RICE.-That is correct, but we do not have to grind the limestone dust we are using in the experimental mine, as that is obtained from a quarry, and is used just as it comes; we can get it very cheaply, as it is a by-product of the quarries. MR. GRIFFITH.-Have any experiments been made with ordinary dirt out of the fields; could not that be used as ground dust? MR. RICE.-If you dry it and powder it enough so it will float in a, strong air current it might be all right for the barriers, but if it is damp there will be a tendency for it to mat together; then it would be quite useless for making a dust cloud. There might also be another disadvantage if used through the whole mine, if it had very much free silica in it, which is bad for the lungs. Limestone and selected shale dust would not affect the health of miners. MR. GRIFFITH.-In order to do very much good with any of those barriers, they ought to be rather extensively used throughout the mines, and there are few mines that have facilities for grinding up this rock into such a fine dust. If the ordinary earth from a plowed field could be used, even if it were not quite so good, it is more accessible and very much cheaper; therefore, in using it, with the universality of the supply through-out the country, it would tend to stop explosions. MR. RICE (communication to the Secretary*).-In closing, it is well to again emphasize that I do not advocate barriers being a "cure-all" for explosions. It will be generally agreed that prevention is best, not only by means of improved methods of using explosives, and ventilation to prevent accumulations of firedamp, but also by either thoroughly wetting the dust throughout the mine, or else so treating it with rock dust or other inert dust that an explosion cannot start. From my observations I believe that rock dusting. is a practicable method, and has the merit of visibility, and remaining effective for considerable periods, whereas the watering method has to be daily followed up, and if neglected for a short period the mine may become in a dangerous condition. The Germans

Jan 4, 1915

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965

AS you and anyone else can understand, a great expense and a large supply of things are necessary for parting a quantity of silver by means of aqua fortis. First, as you have seen, it is necessary to have a great abundance of every kind of cucurbit and alembic, of charcoal and wood, and a large number of pounds of a vigorous, well-purified aqua fortis, because for every pound of silver there are of necessity [71v] at least four pounds or more employed from the parting to the coloring of the separated gold. It is also necessary to prove its fineness and to granulate or beat it, to have furnaces and supplies, and to provide for a thousand other necessities which need not be repeated now. The most important thing in this art seems to me to be that it requires continual working night and day with extreme watchfulness and care. For this reason another way, much quicker, less dangerous, and less expensive than the aforesaid one was found by some clever men (alchemists, I believe) in order to avoid such laborious and heavy methods. It produces the substance of the thing exactly as the acid does. If you wish to make use of it in conjunction with the acid it is possible to render great aid to this work although there is a great difference in the techniques of the two. The method used in this parting is as follows: First, make a round or square wind furnace for melting, below ground or above, and of height and size in proportion to the work and as it comes out best for you. Then take a large clay crucible and fill it almost up to the edge with that silver which contains the gold, cut into pieces, and put it to melt with the silver on top of a piece of brick cut to the size of the bottom of the crucible and resting on a grate in the middle of coals that are burning well. When you see that the silver has been made so hot by the fire that it looks white and that it wishes to begin to liquefy, take a little stick of sulphur or a small piece of antimony and put it in. When this is melted, lifting away the charcoal that covers it, put in more sulphur or antimony (for the method is the same with either one) until the silver is very well melted and these materials properly incorporated. Then for every pound of silver that you put in add half an ounce of sheet copper. When this is melted take your crucible out with tongs or pincers and strike the bottom gently on the coals two or three times so that the gold may make a residue on account of

Jan 1, 1942

By David R. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during wartime, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis's1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for sepa- rating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concen-trating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435.000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PyRite Production According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By David R. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during wartime, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis's1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for sepa- rating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concen-trating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435.000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PyRite Production According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By A. S. Nowick, E. S. Machlin

One of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.' During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time requird for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error This method of showing stress-rupture data has been adopted by many investigators and the NACA.' By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, roo, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time lor rupture on stress, temperature, composition, and structure. In order to obtain this information, an investigation was made at the NACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given composition and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efliciency and power output of gas turbines used in aircraft propulsion can be increased. Theory The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 developed by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate-process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process." For example, in a chemical reaction the unit process is

Jan 1, 1948

By A. S. Nowick, E. S. Machlin

One of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.' During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time requird for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error This method of showing stress-rupture data has been adopted by many investigators and the NACA.' By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, roo, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time lor rupture on stress, temperature, composition, and structure. In order to obtain this information, an investigation was made at the NACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given composition and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efliciency and power output of gas turbines used in aircraft propulsion can be increased. Theory The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 developed by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate-process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process." For example, in a chemical reaction the unit process is

Jan 1, 1948

The great additional clue given to professional books by adequate alphabetical and analytical indexes has been recognized from the beginning in the publication of the Transactions of the American Institute of Mining Engineers The bust ten volumes, edited by Dr Thomas M Drown, the secretary, were provided with indexes, as well as tables of contents Moreover, he included in Vol V (published in 1877), a consolidated index of Vols I to V , inclusive, and, at the triune of his resignation in 1884, he had prepared a similar index of Vols I to X , inclusive, which was published in the following year The indexes of the annual volumes from Vol XI on were made much more extensive than their predecessors Casual mentions, as well as important discussions, were included, the geographical localities of mines of works alluded to in the text were added in the index, and numerous cross-references were introduced, with the purpose of making it easy for the student to discover at once what the Transactions contained, either of thorough treatment or of hints and clues to further inquiry, concerning any topic, locality, or person within their scope In order to extend the advantages of this larger scheme to the earlier volumes a consolidated index of Vols I to XV , inclusive (published in 1888), was prepared by compiling the several annual indexes and introducing additional items for those preceding Vol XI Vol XX , issued in 1892, contained a similar consolidated index for Vols XVI to XX , inclusive, in 1897, a sepal ate index-volume, covering Vols XXI to XXV, inclusive, was published, and on 1902 appeared another for Vols XXVI to XXX These four indexes, for Vols I to XV, XVI to XX, XXI to XXV , and XXVI to XXX, respectively, bound together into a book of about 950 octavo pages have constituted for the last five year s a consolidated index to the Transactions which they cover-with the single difference that the book had to be consulted four times, where a single comprehensive index would require to be consulted but once This disadvantage, however, was relatively small, compared with the great convenience of finding by four trials m one book what would otherwise call for 30 separate searches in 30 books Moreover, the possession of the one might be most useful to a student who did not possess the 30, by indicating to him what they con-

Jan 1, 1907

By Stephen H. Stow

A relationship exists between the color and the chemical composition of the pebbles from the Bone Valley Phosphate Formation. Darker-colored pebbles are relatively high in iron oxide and relatively low in calcium phosphate when compared to lighter-colored samples; the brown color of the phosphate pebbles can be correlated with their iron content and the black and gray colors with their organic carbon content.1,3 It was anticipated that the darkness of a phosphate sample might be quantitatively measured by a simple reflectivity test and that the amount of reflected light could be correlated with the chemical composition of the rock, especially with the elements which cause the color and darkness of the Florida phosphates. Twenty-one samples of production grade phosphate rock from Hillsboro County, Fla., were studied. All samples were ground to -200 mesh for reflectivity tests and analyses. All analyses are accurate to well within ±2% of the reported value, except for aluminum and organic carbon, which are accurate to only ±15% of the reported amount. Reflectivity measurements were taken with a model 610 Photovoltmeter for tri-stimulus amber, blue and green, and white lights. Experimental procedures and data are available upon request. Results Table 1 contains linear correlation coefficients (LCC) for the element-reflectance relationships for the samples. The top portion of the table refers to the LCC between the percent of light reflected off the samples and the percent of a given element (or its oxide) as analyzed. In the lower portion of the table the LCC refers to the relationship between the same reflectance data and the chemical analyses which have been corrected on the basis of 0% acid insoluble material (chiefly quartz) in the phosphate rock. Each LCC presented in Table I is computed for the 14 coarser samples exclusive of the seven concentrates since the concentrate samples appear to have anomalous reflectivities upon comparison with the coarser grades. Only the most significant LCC for each element is presented in graphical form. Discussion of Data Iron: [Fig. 1] is a graph of the relationship between iron and reflectivity (LCC = - 0.98). A good correlation with Fe2O3, is expected due to the relationship between the tan (or brown) color and the abundance of iron oxide, the principal mode of occurrence of iron in Florida phosphates.8 Note the location of the seven triangles which repre-

Jan 1, 1972

By D. E. Furman

The thermal coefficients of linear expansion for several stainless steels have been determined over the temperature range from —300° to 1000°F. The steels studied include types 301, 304, 316, 347, 310 and 330. This wide selection of compositions allows an insight into the effects of austenite stability and alloy content on the expansion characteristics. THE recent increased use of materials in low temperature applications has created a field for which the properties of austenitic iron, chromium, nickel alloys are particularly suited. Tensile and impact values of stainless steels at subzero temperatures have been made available in the technical literature but, as yet, little information has been published with respect to expansion characteristics. In order to supply this need, a study was made of several of the more common compositions. Those selected were types 301, 304, 316, 347, 310 and 330 stainless steel. Both the mean and instantaneous coefficients of linear expansion were determined over the temperature range from —300°F to 1000°F. Procedure The materials used were commercial grades with the exception of type 301 which was made in a 10# high frequency furnace. The compositions are listed in table I. All steels were given an anneal at 1950°F for 30 min and water quenched prior to machining the expansion specimens. Expansion readings were taken on specimens 0.250 in. in diam by 4.000 in. long with a fused quartz tube expansion apparatus similar to that described by Hidnert and Souder.1 Temperature measurements were made with a chromel-alurnel thermocouple calibrated for use at subzero temperatures. A bath of propane was used for temperatures from —300° to —100°F and one of alcohol from —100°F to room temperature. These baths were contained in large mouthed Dewar flasks and cooled to the desired temperature levels by passing liquid nitrogen through glass cooling coils placed in the flasks. The baths were stirred constantly for temperature equalization and were heated by immersing metal rods which were replaced frequently enough to give a heating rate of approximately 150°F per hr. A resistance wound furnace was used for heating from room temperature to 1000°F and throughout this range rates of about 450°F per hr were maintained. The furnace was designed so that the temperature gradient over the specimen was within 5°F. In most instances, the expansion readings were taken during heating from —300° to +300°F at

Jan 1, 1951

By R. Raring, W. J. Harris, J. A. Rinebolt

The effects of additions of alloying elements on the true-stress, true-strain characteristics of 0.30 pct C, 1.00 pct Mn, 0.30 pct Si pearlitic steel were studied. The alloying elements investigated were C, Mn, Si, P, The alloys are compared on the basis of fracture stress, fracture strain, energy to fracture, rate of strain hardening, strain hardening exponent, height of the flow curve, and lower yield point. IN the past, nearly all studies of the effects of alloying elements on the tensile properties of metals have compared the conventional engineering parameters, namely, tensile strength, yield strength, elongation, and reduction of area. Recently, however, the true-stress, true-strain method of recording results from the tension test has been used; Lacy and Gensamer,' Hollomon," and French and Hibbard- are used this method to study the effects of composition on strength and ductility of metals. In this paper, the effects of certain alloying elements on true-stress, true-strain curves of steels with nearly constant grain size and pearlite spacing are presented. The notation employed in this paper is given in Table I. Since the definitions of stress and strain and the analytical geometry of the stress-strain curve have been explained previously, for example by Gensamer,' they will not be reviewed here. However, the method used for the determination of energy to fracture, E,, requires mention. These energy values were calculated on the assumption that the flow curve followed the idealized equation:' corresponds to the specific energy absorption to that strain value. There is justification for preferring the use of eq 1 for the determination of the energy to a particular strain rather than the area under the experimental stress-strain curve, since Gensamer showed that the use of the Bridgman correctione for stress at the neck of a tensile specimen brought the corrected experimental curve nearer to the idealized power-law curve than to the uncorrected experimental curve. However, it should be noted that the difference between the areas under the idealized curve and the experimental curve is not great for strain of less than 1.0, as can be seen from Fig. 1. In this figure, the true-stress, true-strain curve for a 0.01 pct C, 1.00 pct Mn steel is plotted through the experimental data points. From the value of a,, from this curve and the value of n as determined by the Inm-

Jan 1, 1952

By GEORGE H. DERN

IF THE engineer is to go into politics, as I think he should, I believe the curriculum of every engineering school should be amended to include a good stiff course in public speaking. My observation has been that the engineer in private conversation can scintillate as brightly as a life insurance agent or an oil stock salesman, but before an audience, with rare exceptions, he is a total loss. He will not get up and talk. He hides his light under a bushel, and sits on the bushel as dumb as an oyster. I have seen meetings of the Utah Section at which some topic of general interest to the members was up for discussion, and where an animated debate was the logical thing to expect. After the chairman states the subject and invites discussion, there is dense silence. Finally a member, bolder than the rest, gets up and with trembling voice and knees makes a motion. The motion carries, the meeting adjourns, and then the members gather into groups and begin to discuss the question seriously -and intelligently, giving cogent arguments on either side and embellishing their remarks with appropriate or inappropriate epithets illustrations and figures of speech. Now, I am not pleading for more speechmaking. The good Lord knows we have too much of this great American indoor sport already. But I think every man ought to be able and ready to express his opinions at the proper time. Some men have a reputation for wisdom because they do not talk much. We speak of the wise old owl because she never speaks, but in my opinion the owl's reputation for wisdom is vastly overrated. silence is more apt to be a cloak for stupidity than for wisdom. The person who has ideas can- not exert any influence by keeping them locked up in his own mind. The great motive force of the world is not muscle, but ideas, and ideas in order to get in their work must be released.

Jan 1, 1925

By F. R. Wadleigh

It is generally realized and very often admitted by both producers and consumers of coal that there is great need for a revision of existing commercial classifications, and this will involve, of course, determination of a standard classification and a constant revision of marketing practices as they are affected by coal classification. I recently sent out some 200 letters to producers and consumers with a request for their views on the subject of commercial classification. Nearly all of the replies from both sides were that there was needed some change in the present method. There were three or four dissenting voices but the great majority of opinion was in favor of the formulation of some standard commercial classification. The classifications in commercial use today can best be described as a hodgepodge. They are made upon different bases, have different names and have different ways. There are, for instance, about 11 single bases of classifications as used commercially and some 17 or 18 combination bases. Then there were the Tidewater Pool Exchanges. The classification which they put in force is still used in the tidewater markets and has several different bases of its own. It will be considerable of an undertaking to bring about a change in marketing methods as affected by coal classification but it is well worth doing and I think the committee which has been appointed under the auspices of the American Society for Testing Materials realizes the importance of the subject and is on the way to at least bring about some provision for adjusting matters. By way of starting, each member of the Committee on Commercial Classification has been assigned to a general market district and each member is now engaged in collecting the commercial market practice data for submission at the next meeting of the Committee. About a year ago I made up a list of the commercial classifications in the different markets and the total was 171. The 11 single bases I found used in commercial practice were:

Jan 1, 1930

By D. N. Witman

ONE of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance f a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the electrical resistance of ordinary cast iron. The metal specification is as follows: PER CENT. Silicon 2.40 to 2.60 Sulfur Under 0.05 Phosphorus Under 0.08 Manganese Under 0.40 Total carbon 3.60 to 4.00 Nickel 4.00 to 5.00 Copper 0.50 to 0.70

Jan 8, 1921

By D. I. Cameron

A graphical method has been developed and tested for separating the effects of grain boundary and lattice diffusion in polycrystalline materials. The method is based on the assumptions that for unidirectional diffusion from a plane source of radioactive material, the penetration of activity far into the specimen from the source is due solely to grain-boundary effects, and 2) pure grain-boundary penetration is described by a linear plot of log activity vs the perpendicular distance x from the source. The former is based on the fact that at any temperature the grain-boundary diffusion coefficient is always very large relative to the lattice diffusion coefficient; and the latter is based on the derivation of Fisher.1 Using these criteria along with appropriate penetration data (in this case, data for the diffusion of Cb95 in pressed and sintered UO2) one first plots the data as log activity vs x2 and as log activity vs x, as shown by curves 1 and 2, respectively, in Fig. 1. A tangent line to curve 2 for large x (curve 3) is then transferred to the x2 plot as curve 4. The subtraction of curve 4 from curve 1 yields curve 5 which represents only lattice diffusion and may therefore be related to the diffusion coefficient by using the appropriate solution to Fick's second law. It should be noted that the method has inherent inaccuracies for small and large values of x2 and only the subtraction at intermediate values can be used. For the illustrated specimen the calculated diffusion coefficient is 3.4 X 10-11 sq cm per sec at 1445°C while data using a single crystal of UO2 at the same temperature yielded a value of 2.9 x 10-11 sq cm per sec.2 The same method of subtracting grain-boundary diffusion effects to obtain lattice diffusion coefficients has been successfully used to determine self-diffusion coefficients of Th230 in polycrystal- line thoria.

Jan 1, 1962

Prof. HEnRy Louis, Newcastle-upon-Tyne, Eng. (communication to the Secretary*):—I welcome Mr. Hammond's paper as an attempt to give definiteness to the best modern professional practice. Such a codification of our professiollal ethics is urgently needed, seeing how widely the views of nlining engineers direr on some of the points raised; for example, I have no hesitation in performing a class of work, as to which Mr. Hammond seems to entertain some doubts, and, on the other hand, I strongly condemn a practice which he appears to recommend. I have not the least hesitation in making reports for vendors of mining-properties, and am constantly doing so; the best justification for this practice may be found in the fact that such reports have been repeatedly accepted by buyers as giving a correct representation of the facts of the case, which is all that should be demanded from any report. On the other hand, Mr. Hammond advocates that mining engineers should take payment for their reports in shares of a company to be floated upon the basis of such reports. I hold that this is ethically wrong, as even themost honest of men is liable to be unconsciously biased under these conditions. Indeed, I go much further, and maintain that a mining engineer who reports or advises upon mining-properties should never hold any mining-shares at all, or be himself interested in any mine, and this has been my consistent practice for many years. A man who hold shares in a mine, and is called upon to report upon a neighboring property or a similar mine, can never be wholly unbiased; and even if he could be, he would always lay himself open to the suspicion that he was giving a favorable report 80 as to enhance the value of the property in which he himself is interested, or an unfavorable report so as to stifle competition. It is quite as bad for the manager of a mine or the consulting manager to be interested, because he will have access

Jan 1, 1910

By Harrison R. Cooper

This section will outline procedural, statistical, and model applications developed for specific problem solving and for specific applications in beneficiation processes. Iron Ore Processing Introduction of taconite as a basic raw material in the iron ore industry took place with application of high order technical resources for process development and engineering. This investment of resources encouraged computer utilization to maximize efficient use of capital. From this recognition, process control computers have been installed for operations use in the major taconite plants of the iron range. One of these installations, the Minntac Division of U. S. Steel at Mountain Iron, Minnesota, is described in the paper by Chase in these proceedings. Other computer techniques used in taconite processing are outlined by Tuttle, Ahlquist and Carlson, representing Erie Mining. In this volume Tuttle, et al. describe statistical methods for development of information in taconite beneficiation. Statistical methods used in iron ore processing are described by Volin in treating flotation data as outlined in prior proceedings of the symposia and in other publications. 1,2,3 Industrial Minerals The use of linear programming for feed blending at the Carlsbad operation of International Minerals and Chemicals was outlined by Nunnekoven in 1963.4 Subsequent application of this procedure at the Kingston phosphate operation in Florida was described by Loper. Continued development led to installation of an on-line computer in the Kingston plant which reached operational status in 1967.6,7,8 Application of an on-line computer to industrial mineral production accomplished at Kingston is regarded as a milestone in computer use development. Following this achievement, the Cominco potash beneficiation plant near Saskastoon in Canada was automated by installation of an on- line computer programmed to carry out direct digital control functions to effectively operate the plant by process computer. The procedures used in the Cominco operation are described by Madge in this volume. Development of a mathematical model

Jan 1, 1969

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940