Search Documents

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore.

Jan 6, 1960

By J. V. N. Dorr

THE Elko Prince mine is in the Gold Circle district, Nevada, about ½ miles(2. 4km.) from the town of Midas, 55 miles (88.5 km.) west of Battle Mountain and 50 miles (8.5 km.) northeast of Golconda. The district is described by Emmons in U. S. Geological Survey Bulletin 408, 1910. Little was said of the Elko Prince, however, as only a small amount of work had then been completed. The geological structure of the region is simple. The oldest exposed formation, covering most of the area, is rhyolite, which has a light-colored devitrified groundmass enclosing phenocrysts of feldspar, quartz, and magnetite. It has been somewhat weathered and partially stained with oxide of iron. There are several outcrops of andesite which cut the rhyolite. The ore deposits occur as fissure veins, replacement veins, and sheeted zones. The Elko Prince vein is of the first type. The rhyolite near the veins is silicified, stained with oxide of iron, and, at some localities, replaced by ore, or is so permeated by metals as to be classed as ore. The vein filling consists chiefly of quartz, and the values consist entirely of gold and silver. Part of the gold exists as the native metal and part is associated with pyrite. Silver occurs free and its argentite in handed streaks through the vein. These veins trend in a northwesterly direction, with dips varying from 65° to vertical.

Jan 8, 1918

By F. Keller, E. H. Dix, R. W. Graham

Aluminum alloys containing relatively small amounts of magnesium and silicon are of commercial interest because they are readily workable in the annealed form and may be hardened and strengthened by suitable heat treatment. An intermediate temper can be produced in these alloys by quenching after a Solution heat treatment and the alloy in this condition can be formed easily. Artificial aging is required to obtain the maximum mechanical properties but this aging does not cause distortion nor require elaborate heat-treating equipment. The hardening of the alloys after quenching is attributable in part to the retention of the compound Mg²Si in solid solution, while the maximum hardness obtained by subsequent artificial aging is attributed to the fact that the solid solubility of the compound Mg²Si in aluminum decreases with decreasing temperature. Considering the importance of aluminum alloys susceptible to heat treatment, it is surprising how few fundamental investigations have been carried out on the aluminum-magnesium silicide alloys. This paper deals principally with the solid solubility relations of the compound Mg2Si in aluminum and is the sixth paper of a series1 from the laboratories of the Aluminum Co. of America reporting the results of investigations of equilibrium relations in aluminum-base alloys made from high-purity aluminum."

Jan 1, 1931

By R. B. Sosman, J. C. Hostetter

It is well known that ferric oxide, Fe2O3, is paramagnetic, while magnetite, Fe3o4, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe2o3 and Fe3O4 have been almost completely lacking. Fe2O3 and Fe3O4 form a solid-solution series, according to present evidence.' In this series the properties change continuously from Fe2O3 toward Fe3O4, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe3O4, but it has not yet been possible to establish the existence of such a break experimentally. The occurrence of solid solution in this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe2O3 to Fe3O4. The oxygen-pressure curves at 1100" and 1200" are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe2O3 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is impossible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe3O4 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great bulk of natural oxides of iron lie fairly near either Fe2O3 or Fe3O4 in composition. The reason will be

Jan 1, 1918

By Claudio Guarnaschelli

Alteration of the electronic distribution of mineral surfaces by light irradiation has been used to modify the adsorption characteristics of flotation reagents. Energy of a few electron volts is suficient to cause the necessary transitions that either enhance or retard the adsorption phenomenon. The adsorption characteristics of potassium ethyl xanthate on galena and marmatite are presented as functions of the energy of illumination, type of semiconductor, and surface oxidation. In dilute solutions, the adsorption differences are readily detected by controlled kinetic measurements. The correlation between the electronic distribution and the adsorption and desorption phenomena at the solid surface is gaining more attention and acceptance. These interrelations have found a practical application in mineral processing since all of the sulfide minerals display semiconducting properties. By varying the ratio of free electron to electron vacancies, the separation of ilmenite from rutilel and zircon from pyrochlore" has been executed successfully. Plaksin et al.' indicate three possible ways of utilizing the semiconductor properties of a mineral. The first one involves the control of the oxidation-reduction potential of the liquid phase, the second one consists of allowing selected additives to diffuse through the mineral surface, while the third one entails a change in the adsorption and chemical activity of minerals by irradiating their surface. The aim of the present work is to consider the effect of irradiation on the adsorption-desorption characteristics of natural minerals. Since the effect of irradiation is to change the electronic distribution at the surface:

Jan 1, 1971

By A. H. Shoemaker

THE shutdown of Homestake by Government order L-208, with its consequent disruption of a very stable and trained working force, coupled with postwar inflation and the coincidence that a mining depth had been reached that posed problems of ventilation, access to exploration areas, and choice of mining methods that would be applicable to zones of greater rock pressures made a very searching analysis of every phase of Homestake's operations a necessity. Any changes to be made had not only to meet the problems of deeper mining but also had to provide greater efficiency so that the mine might operate at a substantial profit until such time as a gold price adjustment might be forthcoming that would offset post-1945 inflation.

Jan 6, 1958

By Carl A. Allen

Page Introduction................... 367 FactoRs Affecting the Choice of Method......... 367 Review of Stoping Methods.............. 368 Underhand Stoping................ 368 Overhand Stoping................ 370 Longitudinal or Flat-Back Stoping........... 371 Rill-Cut Stoping................. 372 Saw-Tooth Back Stoping.............. 372 Shrinkage Stoping................ 372 Combination Stoping................373 Side Stoping.................. 374* Breast Stoping................. 374 Sublevel Stoping.........,....... 374 Square-Set Stoping................ 376 Filling Methods................. 376 Caving Methods of Mining......... 376 Top Slicing.................. 377 Sublevel Caving................. 379 Block Caving ................. 380 Back Caving into Chutes.............. 381. Costs of Mining Methods.............. 382 Costs of Willing and Blasting. Comparison of Stoping Methods ... 383 Lighting................... 386 Timbering and Handling Ore in Stopes.. A Comparison of Square-Set and Top-Slicing Methods..............386 Tramming.................... 380 Mining oF the Massive Porphyry CoppeR Deposits ....390 Utah Copper and Boston Consolidated Mines.....391 Ray Consolidated Mine.............. 392 Miami Mine.................. 392 Inspiration Mine................ 395 Ohio Copper Mine...........395 Development.................... 398 Appendix..................... 399 Costs of Mining................. 399 Costs of Development............... 406

Jan 1, 1915

By J. P. Matoney, E. J. Sandy, D. A. Dahlstorm

INTRODUCTION Before an understandable discussion concerning coal dewatering processes can be initiated, it is necessary to define some terms of usage. The many different meanings and interpretations of terms preclude development of standard definitions so the terms defined in this chapter should be regarded primarily as working terms intended to facilitate communication.

Jan 1, 1979

By Arthur G. Levy, Henry M. How

The purpose of the investigation on which this paper is based is to determine whether the structural change which occurs in the slow cooling of steel below the transformation range has an important effect on its engineering properties. We recognize two distinct things which occur in steel when it is brought from above to below the transformation range, first, the transformation proper, that is, the breaking up of the austenite or solid solution of the cementite in the remainder of the iron, and the liberation of its components as undissolved cementite and as ferrite or alpha iron; and second, a structural change consisting in the gradual coalescence of the ferrite and cementite respectively into larger and larger separate masses. Let us distinguish these from each other by speaking of them as " the transformation " and " the structural change " respectively. If the cooling is at all rapid the unevenness of contraction induces severe stress; so that in a sense a slow cooling has a third influence, the prevention of such stress. This transformation from austenite to ferrite plus cementite can complete itself only below the transformation range; and, because this structural change is a change in the structural arrangement of the products of that transformation, it too can complete itself only at temperatures below that range, say below 725°; and of these temperatures it is only those between 600° and 725° that give the metal sufficient mobility to permit this structural rearrangement to progress with ally rapidity. The transformation is now known to be rapid, but the structural change is relatively slow. The transformation, the liberation of the dissolved cementite from the state of solution in the austenite to a free state, leaves the steel structurally in the

Jan 1, 1913

By Charles Meyer, Reno H. Sales

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the sericitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte's Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.

Jan 1, 1947

By Henry Howe

- §1. INTRODUCTION.-Any given piece of metal is made up of a very great number of grains, usually microscopic, each of which is a perfect crystal save only in outward form, with cleavage planes of low cohesion, geometrically arranged quite as in the familiar non-metallic crystals. The plastic deformation of such a mass occurs chiefly through the slipping of the crystalline blocks of which each grain is composed along these cleavage planes, causing steps called slip bands to form on a previously polished surface. In this slip, the metal immediately adjoining each of the cleavage planes along which the slip takes place is thought to pass extremely rapidly through a very mobile state into the amorphous state, in which it is harder than the remaining still crystalline metal between the amorphous layers thus formed along the slip planes. Whether the slip planes below the surface in ferrite can be detected by cutting, polishing, and etching sections is in dispute; but if this detection is possible at all, it is usually made impossible by heating the metal even gently. In short, the change along the slip planes does not persist through heating, and it is thought not to persist through time even at the room temperature, nearly all the amorphous metal re-crystallizing. The network in Fig. 22 and the parallel N.-70°-E. lines in Fig. 21 are slip bands in copper.

Jan 3, 1915

By E. O. Chartkoff

IN 1926 one of the authors published researches on the determination and description of the iron-tungsten and iron-molybdenum systems,1 including the equilibrium diagrams. In 1929, further work was carried on, including the examination by X-rays, which is recorded here. Measurements were made of changes in lattice parameters in the solid solutions. Precipitation from the solid solution and the accompanying changes in hardness were studied as well as the formation of the intermetallic compound phases upon sintering a mixture of metal powders.

Jan 1, 1930

NORTH AMERICA ALASKA Anchorage,-Ames, M. B. Culver, H. W. Fiedler, H. L. Fox, E. F. Gallemore, W. A. Kreitlow, E. J. Layfield, R. A. Saarela, L. H. Strandberg. H. Candle,-Bobbins, J. S. College.-Fackler, W. C. Joesting, H. R. Swift. R. E. "Wilcox, H. G.. Crooked Creek-Lyman. R. F. Fairbanks.-Beistline, E. H. CANADA Canadian Army Overseas,¬ Ball, H. D. Brides, C. Butterill. H. J. M. Ladner, F. E. Lane, H. C. Millar, R'. A. Murchison, R. G. Passow, F. M. ALBERTA Calgary-Allen, R. E. de Hart. J. B. Dingman, C. W. Furnical. G. H. Gray, J. G.

Jan 1, 1943

By Gary E. Melickian

Last year's review was characterized as a year of politics and began an era of legislation. The 1972 review can be similarly characterized, with even more rigid health and safety regulations and environmental legislation. The mining industry should be aware of what's happening in the nuclear power and other fields as a result of the National Environmental Policy Act (NEPA) of 1969, where the environmental impact of most major construction activities are already under close scrutiny. Section 102 of NEPA requires that all federal agencies include a detailed statement on specified environmental conditions as part of every report on proposed actions significantly affecting the quality of the human environment. All such environmental reports must consider the same general conditions: • The environmental impact of the proposed action. • Any adverse environmental effects which cannot be avoided should the proposal be implemented. • Alternatives to the proposed action. • The relationship between local short-term uses of man's environment and the maintenance and enhancement of long-term productivity. • Any irreversible and irretrievable commitments of resources which would be involved in the proposed action should it be implemented.

Jan 2, 1973

By Walter P. Jenkey

[ ] I. THE REDUCING ACTION OF CARBON AND OF HYDROCARBONS. Carbon has long been recognized as one of the most powerful reducing agents in the deposition of ores. Investigations, made by myself, of the zinc- and lead-deposits in Southwest Missouri, in the region centering about Joplin, where the formation of the metallic sulphides has been due to the action of bitumen, carbonaceous shales and bituminous coal, Lace afforded abundant evidence that the solid oxygenated hydrocarbons, particularly, when in fine powder and in suspension in the waters circulating through the ore-bodies, are the most energetic and powerful reducing agents known. Bitumen, liberated by the decomposition of the ore-bearing limestone, is found in the Joplin mines in all degrees of fluidity and hardness, dependent on the amount of oxidation it has undergone. From semi-fluid maltha it grades into partly oxidized mineral-pitch, which, by further oxidation, changes to hard asphalt, finally breaking up, from continued absorption of oxygen, into a fine powder resembling in appearance powdered coal. In this condition oxidized bitumen, from its light gravity, is transported readily in suspension in the underground circulating-waters. Bituminous coal and black carbonaceous clays and shales occur as surface formations, often in intimate association with

Jan 1, 1913

By B. K. Miller, R. S. Bradley

THE principal producing areas of fire clay in Missouri are: (I) the east central district, which includes Audrain, Callaway, Montgomery, Warren, and Boone Counties [ ] (Fig. I); (2) the St. Louis district, which includes St. Louis and St. Louis County; (3) the north central Ozark district, which includes Franklin, Gasconade, Osage, Maries, Phelps, and Crawford Counties. [ ] Most of the semiplastict fire clay is found in Audrain, Callaway, Montgomery and St. Louis Counties, and in St. Louis. Flint fire clay is found in Callaway, Audrain, and Montgomery Counties and in most of the north central Ozark district. High-alumina [ ] diaspore clay is found only in the north central Ozark district, except a few deposits found in Montgomery County. This paper is concerned with the semiplastic fire clay that occurs in the east central Missouri district near Mexico, Audrain County, Missouri, which is mined by the open-pit method as practiced by the A. P. Green Fire Brick Co. About one-fourth of the semiplastic fire clay in that district is mined in shaft mines, and three-fourths in open pits.

Jan 1, 1941

By J. R. Thoenen

THE consensus of opinion in the published literature on. Grecian magnesite is that it has been formed by alteration of the serpentine, which in turn was itself a product, of metamorphism from the original olivine intrusion. The general opinion seems to be that the magnesite was formed by descending waters heavily charged with CO2. Inasmuch as this opinion is held by engineers far better qualified than I to speak authoritatively on this subject, I hesitate to dispute that theory. However, certain occurrences coming under my observation do not, to me at least, seem to-entirely substantiate this theory. LOCATION Most of the Grecian magnesite comes from the Island of Euboea, although more recently some deposits have been opened on the mainland near the City of Saloniki, which prior to the war was Turkish. The island, comprising a state or province in the Greek political structure, is roughly 110 miles long and varies from 10 to 30 miles in width. It lies off the east coast of the Greek peninsula in the AEgean Sea with its long axis extending in a northwest-southeast direction. It is separated from the mainland by a long narrow arm of the sea known as the Atalanti Canal. Chalkis (Halkis), the capital on the west coast of the island, is the northern terminus of a branch of the state-owned railway and is connected with the mainland by a single-span, movable, highway bridge, roughly 150 ft. long.

Jan 1, 1928

By B. A. Rogers

The etching effect that is produced on a piece of polished iron or steel when it is heated in hydrogen or in a vacuum seems to have been observed first by Osmond,' who believed that he could distinguish four systems of grain boundaries on a piece of steel which had been heated in hydrogen. In a number of other investigations, samples of pure iron were found, after heating, to have complex networks in which two or three systems of grain boundaries could be detected. It was further noticed that samples that had been polished plane before being placed in the furnace were, after treatment, roughened and undulating over their entire surfaces. From a comparison of the temperature of heat treatment with that of the A3 transformation, it was concluded that the changed appearance of the samples was definitely related to the latter phenomenon. Certain other deductions were made but these are not of importance here and only observations on the appearance of the samples will be reviewed. Ewen2 heated a strip of polished iron in a vacuum in such a way that one end was maintained at a temperature of 1000" C. and the other at 580" C. On the cooler end there was outlined a simple polyhedral network, and at the hotter there appeared the complex systern of lines ant the undulating surface characteristic of iron which has passed through the A3 transformation. He found that in going from the cooler toward thc hotter end the sample maintained much the same character of surface up to the beginning of the transformed area, but that near this region doublc grain boundaries were of frequent occurrence. Rawdon and Scott concluded that the simple type of network brought out by heating a sample of pure iron in a vacuum was of the same type as that developec by ordinary etching methods. They also confirmed the observations of

Jan 1, 1929

By D. J. McAdam, G. W. Geil, R. W. Mebs

AS shown in previous papers by the authors 9-l7† the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses.‡ A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers, 9-I8 the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress, § namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the influence of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture, of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals "should" behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or "plastic fracture " and a "brittle fracture." In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture. In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1947

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation.

Jan 9, 1953