Search Documents

By J. V. Emmons

IT has long been known that the outside skin of tool steel frequently exhibits properties widely different from the interior of the mass. Within the last few years it has been generally recognized that many of these properties were clue to surface decarbonization. The origin and effects of this altering of the composition have been but little studied. C. M. Johnson' arrives at the conclusion that, in annealing, "the most active agent in surface decarbonization is the rust or scale (present on the surface), which is actually reduced to metal at the expense of the carbon in the steel to which it adheres." W. H. Hatfield in his admirable paper, The Chemical Physics Involved in the Decarburization of Iron-Carbon Alloys,' has given us the most tenable theory of the removal of carbon from iron. While Mr. Hatfield's work has been principally clone in connection with the annealing of white cast iron to produce malleable castings, it is frequently applicable to the decarbonization of tool steel. The following equations which he proposed have been fully borne out by the author's experiments: 2Fe3C + 2CO2 = 3Fe2 + 4C0 2C0 + 02 = 2C02 Continuous 2C02 + 2Fe3C = 3Fe2 + 4C0 It is the purpose of the author to show, in a quantitative manner, the effect of various treatments in eliminating the carbon in tool steel. Some of the phenomena of the decarbonized surface will also be described, as well as the practical problems they present to. the manufacturer and user of tool-steel products.

Jan 9, 1914

By John Burns

THE object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-harden-ing characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classifica-tion" is essayed. A.-RELATION OF LATTICE PARAMETER AND ELECTRICAL CONDUCTIVITY TO CHANGES IN PHYSICAL PROPERTIES DUE TO AGING OF FE-C ALLOYS Since Whiteley1 in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A1 point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,2 and at the same time and independently, W. Koster,3 proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By Ray Light, Everett M. White

Numerous articles have been written about the coal miner ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. How- ever, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred ,at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed ,as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597

Jan 1, 1981

By Charles S. Barrett, Frederick N. Rhines, Robert F. Mehl

The solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstatten figures profusely nor with great ease. A study of the Widmanstatten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstatten figures.' Alloys of Aluminum with Copper The most accurate determination of the solid solubi1it.y of copper in aluminum seems to be that by Dix and Richardsoq2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548", and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solu-lion on cooling tends to precipitate the compound CuA12, and this conclusion has been confirmed experimentally by Schmid and Wassermann.

Jan 1, 1932

By Edmund Davenport

Tier; production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium.

Jan 1, 1929

By Bradley Stoughton, M. Miyake

The importance of magnesium alloys as engineering materials has increased rapidly in the past few years. The most important properties of magnesium alloys are their lightness and strength, which result in their extensive use in aircraft and automobile construction. Recent progress in the metallurgy of magneaium seems to offer hope of the production of the pure metal at a reasonable cost. The use of magnesium would doubtless increase greatly if it could be produced at a cost comparable with that of aluminum. A preliminary survey of the magnesium-base alloys shows that the most promising from a practical standpoint are magnesium-aluminum and magnesium-zinc as binary alloys, and magnesium-zinc-aluminum as ternary alloys. The research reported in this paper is a preliminary study of binary magnesium-aluminum and magnesium-zinc alloys, as an introduction to a series of further investigations. Magnesium-aluminum System The magnesium-aluminum system was first studied by Boudouard,1 who merely determined the liquidus. An accepted constitutional diagram was given by Grube,2 who found a compound A13Mg4 (melting point = 462.7" C.) and two eutectics at 35 per cent. magnesium (451.6° C.) and at 68 per cent. magnesium (440" C.) Between the first eutectic and the compound a solid solution exists. This diagram was checked or supplemented by Pécheux,3 Broniewski,4 Eger,5 Schirmeister,6 Voge17

Jan 1, 1926

By A. M. Gaudin

THE study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a, substantially definite size which depends upon the ball size 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with-all the crushers tested. 7. Different methods of crushing produce grains of different shapes.

Jan 2, 1926

By A. C. Heath, E. H. Dix

THE importance of aluminum-silicon alloys in the light alloy field is now generally recognized. Where silicon was once considered detrimental to the properties of aluminum, useful alloys now contain as much as 13 per cent. Furthermore, silicon is present as an impurity in aluminum of even the purest grades. Iron is another important impurity in aluminum and like silicon is found in small quantities in the purest aluminum available today. The manner of occurrence of iron and silicon in commercially pure aluminum and many of its alloys exerts a very pronounced influence upon their properties. The effect of large quantities of iron in aluminum-silicon alloys is so detrimental that it has been found necessary to limit the allowable maximum percentage to as low a figure as is consistent with quantity production and satisfactory physical properties. The intimate relation existing between iron and silicon in aluminum and aluminum alloys makes necessary a more complete knowledge of this ternary system. This paper is divided into two principal parts, dealing respectively with aluminum-silicon solubility equilibria and the constitution of aluminum-iron-silicon alloys. PART I.-ALUMINUM-SILICON ALLOYS The early work on this system was largely confined to determining the general form of the diagram and in this respect the results are in good agreement. Briefly, aluminum and silicon form a simple eutectiferous series without compounds. Until recently the solid solubility of silicon in aluminum had not been accurately determined. Fraenkel1 (1908) stated that aluminum will retain 0.5 per cent. silicon in solid solution. Rosenhain, Archbutt and Hanson2 gave the maximum solubility as about 1.50 per cent. and added that "this solubility does not appear

Jan 1, 1928

By M. Semchyshen, A. P. Coldren, W. G. Scholz

A survey of the Fe-Mo-B system was made to determine the extent to which boron might affect the microstructure and strength properties of iron-rich Fe-Mo alloys. Seventeen vacuum-induc tion melted ingots were prepared with approximate mo-lybednum contents 01 2, 4, 9, and 19 wt pct and approximate boron contents of 5, 14,50, and 630 ppm by weight. Phases extracted from annealed specimens and identified by X-ray diffraction analysis included E Fe3MO2, Mo2FeB2, and an oxide hazling a diffraction pattern practically identical to that of MnFez04. Three types of alloy strengthening were observed: a) Fe-2 pct Mo-B alloys were hardenable by a bainitic-type transformtion of austenite to ferrile; b) Fe-4 pct Mo-B alloys were hardened by the solid-solution mechanism; and C) Fe-9 pct Mo-B and Fe-19 pct Mo-B alloys were hardened by precipitation of the E Fe3Moz phase. Boron was observed to have a very strong hardening effect in the Fe-2 pct Mo alloys and a mild strengthening effect on the 1200°F properties of the Fe-4 pct Mo alloys. In the Fe-9 pct Mo alloys there was no consistent effect of boron on strength at either room temperature or 1200° F. The Fe-19 pct Mo alloys were so brittle that meaningful tensile or creep-rupture data could not he obtained. No dispersion hardening from borides was recognized in any of the alloys. THE high-temperature properties of iron-rich Fe-Mo alloys were studied by Reiter and Hibbard.' They found that the strength of the alloys increased markedly as the molybdenum content was raised from 0 to 15.9 pct by weight. The authors explained the various degrees of strengthening in terms of a) solid-solution strengthening, b) strengthening from a martensitic-type transformation, and C) precipitation strengthening. The objective of the present investigation was to conduct a survey of the iron-rich portion of the Fe-Mo-B system to determine whether the beneficial effects of molybdenum on the strength of iron can be enhanced by the presence of boron. It was thought that perhaps fine dispersions of molybdenum- rich borides would be found which could improve the high-temperature strength of ferritic alloys beyond the strengths attainable by molybdenum additions alone. Also, it was considered worthwhile to study the effects of boron in alloys which are essentially free of carbon. Most, if not all, of our present knowledge about boron in high-temperature alloys pertains to alloys containing carbon and carbides. EXPERIMENTAL PROCEDURES Alloy Preparation. Seventeen 8-lb ingots were prepared from electrolytic Plastiron, unalloyed molybdenum chips, and boron powder by a vacuum-induction melting procedure employing hydrogen as the main deoxidizer. The alloys were melted in alumina crucibles using 35-lb melts, with each melt being split four ways to achieve varying boron contents within four Fe-Mo base compositions. The results of chemical analyses conducted on chips machined from the chilled ends of the ingots are presented in Table I. The boron analyses were performed by a spectrographic method utilizing primary standards prepared from boric acid. They indicated that in ingots to which no boron was

Jan 1, 1964

AMERICANIZE THE MINING INDUSTRY Americanization is the snaking of American citizens; men and women controlled by the ideals of American citizenship, which have been built up by this country's heritage and its unceasing struggle for freedom and democracy and opportunity. That means, first of all, a necessary understanding of what those ideals are and what they mean for the newly arrived foreigner. It means that every kind of anti-American propaganda must be stamped out; that racial prejudices and the misunder-standings which lead to unrest and disloyalty and make fruitful soil for anti-American propaganda must be overcome. The foreigner must understand. He must understand what we are trying to do here in America; he must understand something, at least, of the kind of government we have built up in our efforts to, accomplish our particular aims; he must understand how lie can fit into it all, not only to help America, but to help himself-to make it possible for hint to get from this country what he carne here seeking. First of all, he must learn the American language. He must be able to talk with his fellow Americans-those who were born here and those who have recently cone, like himself, but from a different land. The most dramatic, the most crucial demonstration of the urgency of the need of all this is given to us right now. At the time when it is most essential for this country to be solidly American, enemy propagandists are winning an occasional success here because they give their message to men and women and boys and girls who do not understand our language and consequently do not understand us. These foreigners, whom the enemy is trying to make disloyal, are really in our army, the big army that is fighting the war for America. Most of them are not among the soldiers who will fight on the battle front, but they are in the lines back of these soldiers. The worker in the shipyards and in the mines is just as important a soldier in this war as the man in the trenches. That has been said over and over, but it cannot be said too often. It is just as vital for that man in the mine to know why we are at war as it is for the soldier. His employer has just as great a responsibility to the country as has any general, and it is the same responsibility.

Jan 8, 1918

MAJOR AWARDS JAMES DOUGLAS GOLD MEDAL 1960-Augustus B Kinzel "For outstanding contributions and inspiring leadership in the field of electrolytic and electrothermic winning of nonferrous metals and for his notable administrative ability " BENJAMIN F FAIRLESS AWARD 1960-Charles McElroy White "His ability, energy and determination in starting the top-pressure blast furnace and foresight in providing it with prepared burdens have created the world's dominant metal producer " HAL WILLIAMS HARDINGE AWARD 1960-Samuel H Dolbear "Eminent mineral consultant and engineer-first chairman, Industrial Minerals Division of AIME-first editor, 'Industrial Minerals and Rocks'-for the improvement and increase of industrial mineral knowledge "

Jan 1, 1960

West Virginia University, Engineering Experiment Station, Morgantown, W Va C E Lawall, Director. For copies of Bulletins or other information address the Director Two classes of the Bulletins published by the Engineering Experiment Station are of particular interest in this directory- Research Bulletins, and Extension Bulletins, or bulletins published for use in extension work They are. Research Bulletin 1, The conservation of natural gas in West Virginia (1918), 2, Acceleration stresses in hoisting ropes (1927), 3, Classification of gas wells for operation (1927), 4, Mining methods in West Virginia (1929), 5, The whiteware industry of West Virginia, Extension Bulletin 1, Electricity in mines, series

Jan 1, 1933

EVERY forward-looking mining company realizes the need for employing graduate mining engineers so that there will be a supply of qualified men from which to draw for company officers, executives, and mine managers. The mining industry is competing today with numerous other fields of engineering for its supply of technical men, many of which are more attractive than mining because of better pay, living conditions, and well- regulated company training programs. The Ontario Mining Association and the mining companies of Ontario are conducting a postgraduate training plan which if adopted in the United States, might well encourage top quality men to study mining.

Jan 3, 1950

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) Position of laboratory assistant in metallurgy, pyrometry, and physical testing is vacant. Salary $80 to $100 to start. Knowledge of metallography desirable. Opening for a mine superintendent familiar with stoking methods on narrow gold quartz veins; also for a. superintendent of a 50-ton fine-grind-in, cyanide mill. College man under 40 preferred. Position in sales department is open for a mining engineer, with experience in mine ventilation and possessing some knowledge of fan design; one competent to lay out ventilating systems to meet various conditions.

Jan 10, 1913

By William Allen

For the past six years gravity surveys have been used for underground prospecting in the copper mines at Bisbee, Ariz. The primary purpose of the surveys has been to reduce the diamond drilling and crosscutting necessary for exploration. Since many of the orebodies are small, and geologic control is not always apparent, any information that will direct the drilling and crosscutting is highly desirable. Because of extensive development and exploration work in the copper mines at Bisbee, it has been possible to cover more than 630,000 ft of crosscuts on 30 levels with the gravity surveys. In the process the gravity procedures have been refined to a high degree.

Mar 1, 1956

By Fred W. Shultz

The process engineer is familiar with the in any methods employed in the past for analyzing various materials. These include panning. eyeballing, and wet chemistry. Of those mentioned only wet chemistry has been and will continue to be a standard measure for the elemental content in a given material. However, wet chemistry, by the very nature of the method, can be excessively time-consuming and thus reducing obviously the number of samples that may be processed in a given period. The analysis by X-ray, in most cases, requires nothing more than assurance that the sample is in a suitable state for presentation to the X-ray spectrometer.

Jan 1, 1964

By Leonard Bernstein, Harry Bartholomew

MANY of the properties of metals and alloys are structure dependent. Not the least of these is the grain structure. For example, in producing alloy bonds between silicon or germanium and gold-alloy foil at temperatures above their eutectics (which are, respectively, at 370" and 356°C) but below the melting points of the individual constituents, it was found that wetting was more complete with a fine-grain structure than with a coarse-grain structure. In cases where the assemblies were held together for long periods of time at elevated temperatures, wetting was not as critically dependent on the grain structure as was the case for shorter periods of time. When liquid phase forms, it first forms in the grain boundaries due to the fact that most of the impurities are concentrated at the grain boundaries and that most impurities tend to lower the melting point of the gold alloy somewhat. In addition, grain boundaries are at high-surface free-energy levels and are thus in a more favorable condition to initiate good wetting. A fine-grain structure will have more grain boundaries per unit area than coarse-grain structure thereby making wetting somewhat easier. To make the grain structure of an alloy sys- tem visible, a satisfactory method for differentiating between the different grains of which the system is composed must be employed. For the alloy bonding system previously described, the grain structure on the foil surface is of primary interest. Conventionally used etchants for the gold-alloy system will not adequately delineate grain boundaries in their structures. For this reason an alternate method is proposed for those cases where such a determination is necessary. Foil between 0.0005 and 0.005 in. thick has been used in this determination. The equipment used in this investigation was described in a previous publication.' Essentially, it employs a resistance-type filament which can be heated up very rapidly and cooled very rapidly. A thin refractory material is placed on top of the heating element. This refractory material may be molybdenum, tantalum, tungsten, or even ceramic but its thickness should be less than 0.010 in. to minimize the temperature gradient across it. The gold-alloy foil is placed on top of this refractory material. The temperature of the heating filament is raised to 900°C and cooled down to below 100°C in 5 to 10 sec. During this cycle, the foil can be observed to plastically deform due to its own weight. With no further chemical etching, this assembly is then viewed under a standard metallurgical microscope and the grain size measured. Fig. 1 is a Au-1 pct Sb alloy at 400X magnification and Fig. 2 is a Au-1 pct Ga alloy at 130X. This technique has proved to be an adequate means for controlling processing conditions in producing large quantities of gold alloy foil.

Jan 1, 1963

By W. Julian Patron

TREATMENT of the breaker wash-water discharges to remove the suspended particles of finely divided material is usually most efficiently and economically accomplished in settling or thickening tanks. The purpose of these tanks is to separate the excess water from the solids by sedimentation whereby the solid particles suspended in the water are thickened by the force of gravity. The water overflowing these tanks is either reused for coal cleaning or discharged directly to the streams. The settled solids, which are in a relatively concentrated condition, forming a sludge or thick pulp, can be disposed of by pumping to a storage dam, by slushing into mine workings, by processing for recovery of coal, or filtering by vacuum or centrifugal means and discharging with the breaker refuse. The scope of this paper will be limited to the discussion of settling and thickening equipment, the factors that influence the settlement of solids, and a brief description of tests that can be made to determine the size of settling facilities required for any particular condition. The practical application of sedimentation to the treatment of coal falls into two groups, one of classification or hydro- separation, and the other of clarification and thickening. Classification may be employed to prepare a relatively low- grade fuel, which can be used as is or can be further processed separately. Clarification and thickening is employed where the primary objective is to recover a relatively dewatered solid and return a satisfactorily clear water to breaker or streams. When a stream of water flows across a tank, the time required for a particle to travel from the feed inlet to the overflow must be a little greater than that required for the finest particles or flocs in the feed to settle out of the stream. OPERATION AND TYPES OF SETTLING EQUIPMENT Theoretically, the liquid in a settling tank should rise at a more or less constant rate throughout the area of the tank Under these conditions the rising velocity of the water must be less than the settling rate of the finest particles if clarification is to be obtained. When classification of particles is to be made in the tank, the overflow velocity must be greater than the settling velocity of the particles that are to be removed with the tank overflow. The performance of a settling tank, then, depends on the settling rate of the solids and the current velocities in the tank. The oldest types of sedimentation employ intermittent types of settling tanks of any convenient shape. Means are provided for filling the tank with pulp and allowing it to settle until quiet, for moving the clean liquor and for removing the thickened sludge. The operation is necessarily intermittent but a sufficient number of tanks is employed so that a continuous flow of clear water is maintained. Continuous methods for the sedimentation of slurries were developed in the metallurgical industry. Cones from which settled solids were discharged by gravity

Jan 1, 1946

Contents A - Metal Mining B - Minerals Beneficiation F - Coal H - Industrial Minerals I - Mining Geology L - Geophysics

Jan 11, 1953

Jan 1, 1901