Search Documents

By Thomas F. Bates

ANALYSIS of the chemical and structural differences in minerals often results in a better understanding of the differences in the geological conditions under which they were formed. The minerals in the kaolinite group differ in the amount of interlayer water and in the nature and amount of ordered and/or random shifting of each 1:1 layer with respect to those above and below it. This paper is a progress report resulting from research on the morphology, structure, and origin of fine-grained minerals, supported by Contract N6onr26914 with the Geophysics Branch of the Office of Naval Research. The purpose of the paper is to present data obtained in the laboratories at The Pennsylvania State College and elsewhere, which reveal some of the details of structure of the minerals in the kaolinite group, and to suggest a number of interpretations that bear upon the conditions of origin of these minerals. Be¬cause most of the work in this investigation thus far has been concerned with the relationships of kaolinite, halloysite (4H2O; endellite), and halloysite (2H2O), must of the discussion deals with these members of the group. The first step in the analysis of the differences in two sets of geological conditions is an evaluation of the differences in the minerals that result. Thus the chemical differences between the montmorillonite and the kaolinite clays corroborate other evidence in support of the view that the montmorillonites are commonly formed when solutions are alkaline and leaching poor, while kaolinite usually is associated with acid solutions and good drainage condi¬tions. It is obvious that the greater the differences in the minerals, the more divergent may be the conditions that give rise to them and the more readily one condition can be distinguished from the other. In the kaolinite group, differences between individual members are small, therefore the differences in condition of origin are presumably subtle and difficult to define. At the same time, the very fact that the minerals differ only slightly makes them more sensitive indicators of the exact conditions under which they and the minerals associated with them were formed. Since clay minerals are being used more and more to evaluate the nature, value, and mode of formation of economic mineral deposits, an attempt to define these subtle differences would appear worth while. For purposes of the present discussion, the minerals nacrite, dickite, kaolinite, the so-called "fireclay mineral," halloysite (4H2O), halloysite

Jan 1, 1952

By J. H. Frye, R. M. Treco

ONE of the chief hindrances to an understanding of the hardness of solid solutions is the sparsity of suitable hardness data. There is great need of a large body of hardness data obtained from many different alloys of high purity by identical testing methods and corrected to correspond to a single grain size. A considerable amount of such data has been obtained by means of the Meyer analysis on copper-rich and silver-rich solid solutions. There are enough of these data to permit comparison of numerous alloys at equal solute concentration in these two solvents, but only in a few cases is it possible to construct hardness-concentration curves for any given alloy. Therefore additional hardness work on most of these alloys is desirable. The primary solid solutions of silver with cadmium, indium, tin, or antimony as solute are of special interest, since all elements are from the same period of the periodic table and since, as shown previously,1 the hardening effect of equal percentages of these solutes is proportional to the lattice expansion produced by them. This paper presents the relation between hardness and concentration in the silver-antimony system from very dilute to nearly saturated solutions of antimony in silver. EXPERIMENTAL PROCEDURE Alloys were made from silver, 99.99 per cent pure, and antimony, 99.975 per cent pure. Silver and antimony were placed in graphite crucibles that had an ash content of less than 0.75 per cent. These metals were melted and allowed to solidify in a vacuum, which, after melting was complete, was usually equivalent to 3 mm. Of mercury. A high-frequency furnace was used. The ingots so obtained were worked and annealed to lessen segregation and to control grain size. Annealing was done in evacuated and sealed glass tubes. Hardness measurements on specimens from these ingots were by means of the Meyer analysis.3,4 Using a 4-mm.. ball, impressions were made under seven loads from 25 to 400 kg. The diameter of impression made under each load was measured. This enabled calculation of the constants in the well-known formula of Meyer. L=ad¬n where L = load, d = diameter of impression, a = a constant, n = a constant The Meyer hardness is defined as P = L/(1/4pd2) or P = 4adn-2/p Meyer hardnesses corresponding to d = 1 and to d = 4 are of especial interest, since the first corresponds to comparatively slight plastic deformation and the second to the maximum plastic deformation producible by penetration of the ball. These

Jan 1, 1944

By M. B. Ramachandra Rao

The spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° 17' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1—the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous mica-chlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, litho-margic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. Method of Survey and Apparatus Employed The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The Potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1946

By A. Gatti

Studies were made on the system iron plus alumina. Various methods of dispersing and various amounts of alumina were used. Powder metallurgy techniques were used to produce the final product. Microstructures and some mechanical properties are presented. Alloys containing up to 16 pct alumina by weight are ductile at all temperatures tested. The ivon-alumina materials have a higher yield stress and improved creep resistance over that of pure iron. SINCE the development of SAP' an A1- Al2O3 powder metallurgy product, great interest has been shown in the development of a SAP-like structure in metals and alloys other than aluminum. The outstanding properties of this class of materials are: 1) Good creep resistance at high temperature. 2) High yield strengths and high hardness at high temperatures. 3) High recrystallization temperature. However, the lack of ductility and formability has thus far limited the applications of SAP-like materials. The following report deals with methods of dispersing A12O3 in Fe, processing of powders into rod, structures produced after processing, and mechanical properties of the iron-alumina material produced. Methods of dispersing the alumina and also the volume fraction of alumina added were varied. MATERIAL Powder Processing— Four methods of obtaining dispersions of alumina in iron were studied. 1) Oxidation-reduction of a Fe + 8 pct Al alloy. .2) Coprecipitation of Fe(OH)3 + Al(OH)3 from aqueous solution. 3) Colloidal mixing of Fe,O3 and Al2O3. 4) Colloidal mixing of Fe powder and A1,O3. Fig. 1 is a processing flowsheet which outlines the processing steps taken to produce a final extruded bar 1/4 in. in diameter and about 30 in. long. The - 100 mesh iron-aluminum alloy was oxidized by placing a thin layer of powder on an alumina plaque. The reduction step was modified to include 1/2 hr at 1000°C since the powders tended to become pyro-phoric unless sintered slightly after low-temperature reduction. Compacting was done in a 1-1/8-in.-diam pressing die. The slugs produced averaged 1 in. in length. The billets were encased in low-carbon steel cans shown schematically in Fig. 2. The blank is included for structure and property comparison purposes. TESTING PROCEDURE All tests were made on as-extruded material.

Jan 1, 1960

By R. E. Ogilvie, H. C. Gatos, R. E. Hanneman

The effect of high pressure on the stability of the (any phase transformation in the Fe-V system was studied by experimental and theoretical methods. The maximum solubility limit of the y loop of the atmospheric phase diagram was found to increase by a factor of five at 40 kbars pres-sure. The solubility limits of (Y and y phases are calculated on an approximate thermodynamic basis at pressures of 20, 40, and 50 kbars as a function THE high-pressure behavior of the a =^ y transformation in iron and iron-base alloys has been the subject of considerable interest recently. For those binary or higher-order alloy systems possessing a closed y loop, the effect of pressure is to extend the region of solubility of the more dense y phase. Although quite accurate calculations have been made of the a y temperature-pressure diagram of pure iron,' only very approximate thermodynamic calculations or experimental measurements have been made of the pressure dependence of a ^ y equilibria in binary systems exhibiting a y loop.2"4 of temperature and are found in excellent agreement with experimental results. The experimental high-pressure phase diagrams were determined using binary diffusion couples diffused under simultaneous conditions of high pressure and temperature and analyzed with an electron microbeam probe. Approximate calculations of the stabilizing effect of high pressure on the o phase are qualitatively confirmed by experimental results. These previous calculations have primarily dealt with the slopes of the allotropic a (Y= y phase boundary at terminal solubility. The lack of detailed understanding or accurate experimental results of the pressure dependence of the two-phase a ^ y field has been due, in part, to the types of experimental methods previously employed. The primary purposes of the current paper are twofold: 1) to develop and make use of thermodynamic expressions with the aid of supplementary data, to approximately calculate the pressure dependence of the entire y loop and the two-phase ((Y + y) width in the Fe-V system; and 2) to accurately determine the corresponding experimental high-pressure phase diagrams. The current paper describes the powerful method used which enables the simultaneously measurement of phase equilibria and diffusion under high pressure and temperature. A second paper, part 11, will deal with the effect of high pressure on binary diffusion in the Fe-V system.

Jan 1, 1965

By A. L. Holley

THE general usage of engineers, manufacturers, and merchants, is gradually, but surely, fixing the answer to this question. In every country rails, boiler-plates, and machinery bars, whether hard or soft, are almost universally called steel, when they are made from cast ingots. Other names for the softer steels, such as " homogeneous metal," " Bessemer iron," " Martin iron," and the like, have failed to obtain general recognition. The meaning of the term steel, before it was enlarged to cover newly developing varieties, has been traced, by a recent writer, down through Percy, Shakspeare, and the Bible, in a most interesting manner, from an archaeological point of view. Undoubtedly, it did characterize hardness and other qualities imparted by carbon. It is within the memory of most of us, that all steels were tool steels, and that the soft, structural varieties were introduced-varieties which harden but little, which bend cold, and which, in many physical properties, are akin rather to wrought-iron than to tool-steel. But, since both the hard and the soft steels are made by the same processes, and have their great, distinguishing structural feature in common, viz., homogeneity resulting from fluidity, it has come to pass, despite every other proposed nomenclature, that all the compounds of iron which have been cast in malleable masses, are called steel, the term wrought-iron being still confined to malleable iron made from pasty masses, and hence laminated in structure. No inconvenience has been found, so far, in distinguishing between the more or less carburized products, in general, by the terms " high-steel," " low-steel," " tool-steel," etc., and, in particular, by prefixing the percentage of carbon and other ingredients, to the terra steel. Steels which contain distinguishing ingredients other than carbon, are called "chrome-steel," " titanium-steel," and the like, just as variously compounded bronzes are called "phosphor bronze," "alu¬minium bronze," etc. Thus the combination of several words or symbols, and figures, may completely disclose the characters of the metal, in terms that are subject to no misunderstanding. But inasmuch as several high metallurgical authorities and clever writers have of late proposed to disturb this natural and somewhat settled nomenclature, it seems important to consider the claims of the various classifications. I shall attempt, in this paper, to show

Jan 1, 1876

By J. R. Long, T. R. Graham, C. W. Matthews, R. S. Dean

In a previous paper! the authors reported on the mechanical properties of a 65 per cent copper, 10 per cent manganese, 25 per cent zinc alloy as compared with, similarly processed cartridge brass. Additional investigations by these laboratories, on higher copper alloys, have demonstrated that at lower zinc concentrations even larger amounts of pure manganese may be added to copper-zinc alloys without exceeding the single-phase solid solution limits, and that similar increases in tensile strength, yield strength, and hardness may be obtained without excessive decreases in ductility. Several compositions in this range showed also a decided color change with increasing manganese. The normal "brassy" color was considerably lightcncd and reduced to a faint yellow cast at 15 per cent manganese. With higher manganese contents the alloys were essentially white and similar in appearance to the nickel-silver alloys. From this work it appeared that it would be desirable to determine more completely the properties of the wrought and annealed white alloys. Accordingly, a more detailed study was planned of an alloy having the composition 70 per cent copper, 20 per cent manganese, and 10 per cent zinc. This alloy remained single-phase throughout the working and annealing cycles of the preliminary tests and appeared to be' about the strongest of the white single-phase alloys. The project included also an investigation of additional alloys, deviating from this composition by 5 per cent of each of the three components to evaluate the effects of variation in composition and a study of the propertics of the central alloy made with silicothermic manganese. Material Preparation Electrolytic manganese, wirebar copper, and electrolytic zinc were used for the preparation of the alloys. Representative analysis of the electrolytic manganese seldom exceeds 0.01 per cent iron, 0.02 per cent sulphur and 0.02 per cent lead, with no silicon or aluminum. A typical sample of the silicothermic manganese metal contained 2 per cent iron, 0.81 per cent silicon, 0.16 per cent carbon, and 0.36 per cent aluminum. Melting and alloying were performed in a high-frequency furnace with magnesia crucibles. Melts were deoxidized with small aluminum additions and cast into 25-lb. slab ingots. Care was exercised in deoxidation to avoid excessive amounts of residual aluminum, which has been found to have significant effects on alloys in this system. All ingots were hot-rolled at 1200' to I300°F. and then cold-rolled with intermediate anneal-

Jan 1, 1945

By A. L. Holley

The general usage of engineers, manufacturers, and merchants, is gradually, bat surely, fixing the answer to this question. In every country rails, boiler-plates, and machinery bars, whether hard or soft, are almost universally called steel, when they are made from cast ingots. Other names for the softer steels, such as " homogeneous metal,'' "Bessemer iron," " Martin iron," and the like, have failed to obtain general recognition. The meaning of the term steel, before it was enlarged to cover newly developing varieties, has been traced, by a recent writer, down through Percy, Shakspeare, and the Bible, in a most interesting manner, from an archœological point of view. Undoubtedly, it did characterize hardness arid other qualities imparted by carbon. It is within the memory of most of us, that all steels were tool steels, and that the soft, structural varieties were introduced—varieties which harden but little, which bend cold, and which, in many physical properties, are akin rather to wrought-iron than to tool-steel. But, since both the hard and the soft steels are made by the same processes, and have their great, distinguishing structural feature in common, viz., homogeneity resulting from fluidity, it has come to pass, despite every other proposed nomenclature, that all the compounds of iron which have been cast in malleable masses, are called steel, the term wrought-iron being still confined to malleable iron made from pasty masses, and hence laminated in structure. No inconvenience has been found, so far, in distinguishing between the more or less carburized products, in general, by the terms " highsteel," "low-steel," "tool-steel," etc., and, in particular, by prefixing the percentage of carbon and other ingredients, to the terra steel. Steels which contain distinguishing ingredients other than carbon, are called "chrome-steel," "titanium-steel," and the like, just as variously compounded bronzes are called " phosphor bronze," " aluminium bronze," etc. Thus the combination of several words or symbols, and figures, may completely disclose the characters of the metal, in terms that are subject to no misunderstanding. But inasmuch as several high metallurgical authorities and clever writers have of late proposed to disturb this natural and somewhat settled nomenclature, it seems important to consider the claims of the various classifications. I shall attempt, in this paper, to show

By William S. Hannan, H. Rush Spedden

FLOTATION may be defined as a process whereby mineral particles are concentrated by selective adhesion to air-liquid interfaces. The process involves attachment of desired mineral particles to air bubbles, and removal of the mineralized air bubbles from the surface of the pulp as a mineral concentrate. PROBLEM Although great strides have been made in understanding the principles of flotation, one part of the process which has not been adequately explained is the mechanism by which selected mineral particles become attached to air bubbles. A glance at the froth of an operating flotation cell demonstrates adequately that use of proper reagents and conditions will result in such attachments; but how such attachment takes place is not definitely known. A better knowledge of this factor might lead to improved flotation practice either through altered machine design or the application of scientific innovations. Direct observation of the behavior of mineral particles and bubbles in an operating cell does not appear promising because of the complexity of the system. For this reason, conclusions concerning the problem must be deduced from theoretical considerations or from observation of simplified systems designed to reproduce conditions thought to exist in an operating cell. PRESENT THEORIES Two mechanisms have been recognized as fundamental in particle-bubble attachment: gas precipitation and direct encounter. It is a simple matter to demonstrate in the laboratory that attachment can be brought about by either mechanism. As to the relative importance of the two in a particular flotation system, however, there is a divergence of views. Taggart1 states, Under exceptional circumstances sufficient force and time to effect attachment may conjoin in an ore pulp undergoing agitation, and a preformed bubble adhere to a collector-coated mineral particle, but the occurrence is rare. . . . Pulp-body froth flotation effects selection in the body of a conditioned pulp by causing gas bubbles to precipitate from solution in the liquid phase preferentially at the surfaces of collector-coated particles, and to cling to these particles. Gaudin2 states that, within the pulp body of an agitation machine, attachment of mineral particles to air bubbles occurs as a consequence of contact between the two. This theory has been supported by theoretical reasoning and much circumstantial evidence. Perhaps the most interesting bit of evidence in favor of this theory is the difficulty in the flotation of fines. If attach-

Jan 1, 1947

By H. J. Stehli

The first sintering of zinc ores was done at the Bartlesville plant of the National Zinc Co., under the auspices of the late Otto Rissman. Mr. Rissman, who had had a long experience in the treatment of zinc ores, well realized all the difficulties of satisfactorily roasting zinc concentrates, which were becoming finer and dustier as each year went by—thus increasing the difficulties of roasting them in the existing forms of roasters, which were furnaces of the Ropp, Hegeler or similar types. Mr. Rissman's idea of the advantages of sinter was expressed in this way: in a zinc ore dead-roasted in a mechanical furnace there are many particles that are just like an egg; that is, they have a hard and impervious film of fused material on the outside, and in the retorting this completely cuts off access of the reducing gases to the center of the egg until a temperature has been reached at which this shell of the egg can be broken down through fusion. A particle of sintered zinc sulphide, on the contrary, is exactly like a piece of sponge. The moment the retort reaches the temperature at which the reactions can take place, they begin, because the reducing gases have ready access to the interior of the particles by means of the pores of the '" sponge." His faith in the advantages of sinter was amply borne out by the results obtained at the pioneer sintering plant for zinc ores installed by the National Zinc Company. Early Method of Sintering The method of procedure at Bartlesville was to roast the zinc concentrates down to somewhere in the neighborhood of 8 per cent residual sulphide sulphur; to cool these, then to wet them down to the proper moisture and mix them in the mixer of the sintering plant; then to sinter them by means of the heat available from the residual sulphides. The sulphur contents of the roast varied considerably, of course, as it was difficult with the furnaces in use to control the roasting exactly at any point short of dead roast. Hence at times the concentrates were roasted a little too low to sinter readily, and at such times the lack of sulphur was made up by the addition of raw concentrates to the sintering-machine charge in suitable amount.

Jan 1, 1937

By Ernest L. Ohle

IN 1943 diamond drilling from the surface in an area 2 miles southwest of Leadwood, Mo., discovered a lead deposit of a markedly different character from the usual southeast Missouri type. Subsequent drilling of about 500 holes indicated several million tons of ore, and in 1950 a 701-ft vertical shaft was sunk into the orebody. This paper describes the geology, of this interesting occurrence insofar as it is known from the drilling and the small underground exposure at the bottom of the shaft. Geology The location of the Southeast. Missouri Lead Belt and of 'the Hayden Creek property are shown in Fig. 1. As shown here, there are two separate producing areas, one from which the larger tonnage has come, located near Bonne Terre, Flat River, Desloge, and Leadwood, and the other to the south around Fredericktown and including famous old Mine LaMotte. The best published description of Lead Belt geology is by Tarr.* In pre-Cambrian time in this cherty dolomites. Several of these formations may be found in direct contact with the pre-Cambrian as their deposition progressively overlapped the older rocks on the flanks of the igneous knobs and ridges. Immediately overlying the pre-Cambrian there is, not uncommonly, a thin basal conglomerate of granite or porphyry boulders, which is incorporated into the overlying sediments. Deposition of the lower part of the rock section was fairly continuous, and the Lamotte sometimes grades almost imperceptibly into the lower sandy Bonneterre. Since the sediments were deposited on an uneven floor, they tend to reflect the irregularities in that floor. Most of the steep dips found in the district, that is, dips in excess of 10°, are original dips and not caused by deformation. Such domelike structures in the sedimentary rocks around the igneous knobs have localized a considerable number of the orebodies in the district and particularly those in the Fredericktown area. Many of the larger orebodies, however, have no close relation to the pre-Cambrian topography. Most of the lead production has come from the lower 150 ft of the Bonneterre formation, where disseminated ore spreads laterally parallel to the bedding for great distances. Average stoping height is about 20 ft, but in a few places there are stopes over-175 ft high.

Jan 1, 1952

By M. B. Ramachandra Rao

The spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° 17' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1—the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous mica-chlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, litho-margic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. Method of Survey and Apparatus Employed The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The Potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1946

By H. W. III Straley

SOME ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbert.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information on: (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1941

By John H. Melvin

THE Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. GEOLOGY Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its uncemented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable - slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1947

By Rizo-Pairón Alfonso, A. M. Gaudin

PREVIOUS studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector The results obtained indicate that a I I ratio of collector ion to activator ion gives optimum results, and that a 2 I ratio almost fails to achieve activation and flotation Yet, a 2 I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids, they confirm that an adsorbed coating is inescapable APPARATUS AND SUPPLIES The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz The flotation machine was built according to the design of D W McGlashan It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel stator, as in the Fagergren laboratory machine The air intake is controlled by a valve, and the cell consists of a beaker The quartz was obtained from vein quartz stored in large chunks It was first crushed to 20 mesh, then sized on a 28-mesh screen The 20 to 28-mesh size alone was retained for use This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used The barium was used as barium chloride, Baker's analyzed C P The oleate was used as sodium oleate It was prepared from sodium hydroxide, Baker's analyzed C P , and oleic acid purified by R R de Arellano3 in the laboratories at the Massachusetts Institute of Technology The purification procedure was elaborated from the recent researches of Brown and Shinowara 2 It consisted in (I) saponification of olive oil with potassium

Jan 1, 1942

By John L. Boardman

BECAUSE of the attention that has re¬cently been given to the health and safety of miners by various organizations such as the A.I.M.E., The American Congress, Mining Section, National Safety Council, as well as the Bureau of Mines and various state mining departments, your committee on health and safety deemed it best to call attention this year to the mine-accident cause that is by far the most important; namely, injuries due to falls of ground, rock, roof and coal. Each of several members of the committee contributed a brief outline of the importance of this accident cause in his district. While these papers were brief, it would require too much time and space to give them in full, therefore we present an outline of each and summation of all. REPORT OF M. D. COOPER, HILLMAN COAL AND COKE CO. M. D. Cooper, Division superintendent, Hillman Coal and Coke Co., Pittsburgh, Pa., contributed the following: During the period from 1930 to 1939, accidents from falls of roof in bituminous mines average 54.3 per cent of all accidents. In mechanized mining, there is a tendency toward reduction in this class of accidents because the operator of the machine is usually at a distance of 10 to 20 ft. from the face, whereas. in hand loading the miner is close to the face during most of the shift. No doubt the use of aluminum and light steel beams supported at regular intervals by jacks, a common practice in mechanical mining, has contributed to the favorable record so far developed. REPORT OF M. H. FIES, DE BARDELEBEN COAL CORPORATION Milton H. Fies, Vice-President, DeBardeleben Coal Corporation, Birmingham, Ala., says: With reference to the types of mining, it is suggested that a clear understanding be had as to the character and thickness of the directly overlying strata, with especial consideration to the strength and in some cases an analysis of it. In coal mining, generally speaking, overlying strata higher in silica than others is stronger. In changing from narrow to wide places, the procedure should be experimental, both as to the width and depth of places and as to the nature of the necessary timbering. Since most of the accidents in coal mining particularly are due to falls of roof and coal, this phase of mining should be attacked with vigor. There is no substitute for discipline and, in this connection, under present conditions it is important that cooperation by the labor organizations be sought and that a spirit of fairness prevail. Frequent and thorough inspection of all active working places should be made.

Jan 1, 1941

By Alfonso Rizo-Patrón, A. M. Gaudin

PREVIOUS studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I : I ratio of collector ion to activator ion gives optimum results, and that a 2:I ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. APPARATUS AND SUPPLIES The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel stator, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1942

By E. R. Buchanan, R. E. Reed-Hill

A transmission electron microscope study was made of magnesium single crystals deformed in torsion using the basal pole as the forsional axis. While this type of deformation is predicted to result in the formation of hexagonal networks of screw dislocations, these networks were not observed. The basic dislocation arrangement consisted of arrays of nearly parallel and approximately equally spaced dislocations. The average dislocation density was over an order of magnitude higher than that required to account for the torsional deformation. The observed high rate of work hardening in these crystals is consistent with both their high dislocation densities and the arrangement of dislocations in pile-ups. The experimental observations are also in agreement with the assumption that dislocation sources are activated not only at the surface but at interior locations as well. In considering torsional deformation, Amelinckx and Dekeyser1 postulated that when a torque is applied to a crystal oriented with a glide plane normal to the specimen axis, deformation occurs by the following steps: 1) Nucleation of dislocation sources at or near the specimen surface in areas where the shear stress, resolved along a slip Burgers vector, is a maximum; 2) the screw orientations of the dislocations accommodating the twist move inwards towards the specimen center. If two glide directions lie on the glide plane, the geometry shown in Fig. 1 should result; 3) the screw dislocations that pile up in the central part of the specimen cross-slip to form a grid. At the same time, screws of opposite sign and most edges leave the specimen. Tinder,2 using zinc crystals twisted about the basal pole, independently reached essentially the same conclusions. He suggested a mechanism involving nucleation of ?(1120) screw dislocations at the six points of highest resolved shear stress that lie on the cross-section near the surface. Under the applied shear stress these dislocations were assumed to move inward and interact so as to form a hexagonal network of screw dislocations. Today it is often accepted that rotational slip occurs by a mechanism of the above type, but to our understanding this has never been experimentally proved. This paper reports an experimental study of rotational slip, using magnesium single crystals, that indicates that in this metal rotational slip does not conform well to this mechanism. EXPERIMENTAL PROCEDURES Mechanical Testing. Specimens with a (0002) axis were prepared from magnesium crystals of 99.95 pct purity grown by Jillson's3 modified Bridgman technique. The crystals were acid machined into cylindri-

Jan 1, 1970

By B. M. Larsen, T. E. Brower

INTRODUCTION THIS discussion is based on statistical manipulation and evaluation of operating data from several commercial blast furnaces which include rather wide variations in practice. We are concerned here mainly with the effect of manganese on sulphur elimination under operating conditions in commercial blast furnaces, but this effect can be outlined more clearly by including certain other variables such as silicon in iron and slag basicity, which are all in part interrelated. Real progress in understanding all of the smelting-zone reactions in this process requires more laboratory studies of slagmetal melts similar to those in the blast furnace, with careful control of oxygen pressure. Such experimental work is very difficult, however, and in the meantime, with the present scarcity of more fundamental data, such statistical trends and correlations as can be obtained from commercial furnace operating records may help in choosing laboratory test conditions as well as adding to our knowledge of operating procedures. We do not know just why the furnace data are apparently so irregular that statistical treatment of large numbers is needed to obtain accurate trends. It is .partly caused, no doubt, by the many simultaneous variables present, but there are perhaps also such factors as: (I) the continual swings up and down so characteristic of the process; (2) difficulty of accurate sampling of co-existing phases, as well as (3) the presence of both equilibrium and rate factors as a result of the fast driving of the process, In desulphurization, for example, the flow of thin layers of slag and metal over solid coke surfaces, plus the contact between droplets of iron falling through the slag layer in the hearth, would lead one to expect a close approach to equilibrium, On the other hand, most of the critical part of sulphur removal may occur in a short time and distance below the tuyeres with perhaps an accompanying decrease in oxygen pressure and the concurrent reduction of much of the silicon and manganese, so its degree of approach to equilibrium may be quite variable. PROBABLE CHEMISTRY OF DESULPHURIZATION Since there is little evidence that sulphur atoms in the iron solution are associated to any appreciable extent in molecules such as MnS, the transfer from slag to metal and back again can be written:* [(FeS) -, [FeS],[I] hence the following reactions seem most probable in the slag phase, (FeS) + (CaO) = (CaS) + (FeO), [2] and, (FeS) + (MnO) ;:2 (MnS) + (FeO). [31]

Jan 1, 1948

By S. Yukawa, M. J. Sinnott

A high resolution autoradiographic study of the diffusion of a nickel isotope (NP3) into copper in the temperature range of 650° to 925°C, with particular emphasis on grain boundary diffusion, has been made. The extent of grain boundary diffusion is a function of the grain boundary angle and the diffusion temperature. The ratios of the grain boundary diffusion coefficient to the lattice diffusion coefficient ranges from 104 to 105. The activation energy for grain boundary diffusion decreases with increasing grain boundary angle. STUDIES and reviews&apos;-8 of metallic diffusion have indicated that grain boundary diffusion is a common phenomenon but quantitative studies of the many variables involved are not numerous. The present work was concerned with determining the influence of the crystallographic orientation of the grain boundaries and the temperature on the extent of boundary diffusion of nickel into copper. The study involved essentially three steps: 1—the production of grain boundaries of known crystallographic orientation, 2—the determination of the extent of diffusion into the boundaries, and 3—the analysis of the resulting data in terms of the usual diffusion concepts. The grain boundaries investigated approximated the simple tilt variety having l° of freedom. They were produced by controlling the solidification from a melt of Cuprovac (a high purity vacuum-melted copper obtained from Vacuum Metals Corp.) of a pair of seed crystals so that the bicrystals of copper produced had a common <100> axis. By rotating one seed crystal relative to the other, a simple tilt boundary was produced. The angle of rotation between the two crystals is the grain boundary angle 8, or what is sometimes termed the misfit angle. In all, some 16 boundaries ranging from 2" to 72" in 5" to 10" steps were investigated. The crystallographic orientations were measured with the use of both X-ray and optical goniometric techniques. The <100> axes in the crystals were found to be parallel within 2" to 3" with the exception of one crystal (8 = 12") in which the axes were 6" from being parallel. All bicrystals showed evidences of sub-grain structures. Laue analyses showed that these subgrains differed in orientation up to a maximum of 2". Because of these variations, and some curvature in the boundaries, the grain boundary angles listed are actually average values and deviate from the 1 o of freedom boundaries. The stripping film technique of high resolution autoradiography was used to detect the diffusion of the nickel isotope into the grain boundaries of the bicrystals of copper. Kodak experimental permeable stripping film with an emulsion layer 5 u thick

Jan 1, 1956