Search Documents

By H. F. Yancey

THE jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed at about -1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation Jüngst1 concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 4, 1925

By J. E. Powers, T. D. Taylor, N. E. Wood

A computer program has been developed to simulate a gas transmission 1ine operating under transient conditions. The program was developed by application of the basic mass and momentum balance equations. The nonlinear equations thus obtained were transformed by the method of characteristics and finite-difference techniques to make them suitable for machine computation. Three tests of the computer program were made. In each of these, the initial condition was assumed to be steady-state flow, the inlet density was held constant at the initial condition, and the outlet mass flow rate was varied with time. One test was theoretical in nature, but the others were made for direct comparison with actual field data. Results of the tests are presented in graphical form. INTRODUCTION Theoretical investigations of the transient flow of gas in long pipelines have been limited in number. In 1951, Olds and Sage4 developed a gaphical method of solving the nonlinear flow equations describing transient gas flow in a long pipeline. Research in this field at the U. of Oklahoma was initiated by Nelson1 in 1956. Nelson utilized a computer to solve numerical equations involving a lengthy trial-and-error procedure, and his results have been reported in the literature? It does not seem likely that Nelson's method can be extended to the analysis of transient behavior of pipeline networks; therefore, the investigation to be discussed in this paper was undertaken to improve and extend the previous work. The following discussion presents, briefly: (1) the basic differential equations governing transient flow, (2) transformation of these equations into a form suitable for machine computation. (3) role of boundary conditions in the calculations, (4) a very brief description of the computer program which was developed to simulate the pipeline and (5) results of tests of the computer program.

By George Smith

IN the utilization of natural resources owner, operator, and consumer should share the attendant benefits. Development needs to be planned under terms recognizing fully the interests of all concerned, for any undue advantage given to any one of these participants is apt to involve even greater and disproportionate injury to one or both of the others. For this reason it is well to preface any consideration of needed reforms in legislation affecting the disposition of public land with a survey of certain fundamental principles that determine the general conditions of all land transfers preliminary to development, utilization, and production. The disposition of any undeveloped natural resource, whether timber, oil, coal, or water power, as a transaction to which hand owner and prospective developer are parties, must be based in theory upon a division of expected returns. Whatever the terms of such disposition, neither party can reasonably ask for anything other than an equitable division of the returns. Under this analysis three and only three questions need to be discussed ; namely, what are those profits, how is this division to be accomplished, and what is the equitable basis of division ? The answer to the third question should probably be found by applying to the problem the principles of theoretical sociology, and' the question need not be mentioned further at this time, inasmuch as it does not involve the practical considerations to be kept in mind in connection with the other questions, which are concerned with only the measure of returns and their division. That is to say, whether the land owner's equity is to be stated as 95 per cent. or as 5 per cent. of the profits attending the development of the particular resource, no change would be necessary in the method to be adopted of arriving at the closest approximation of the prospective total profit.

Jan 10, 1913

By Milnor Roberts

The Nicola Valley coal-field is small, but it seems likely to become important because of its commanding position in a rich region that is developing rapidly. Bituminous coking-coal in workable quantity has not been found at any other point between the Crow's Nest Pass region, about 400 miles to the east, and Vancouver island, 250 miles westward. The Canadian Pacific railway reached the Nicola valley two years ago ; two other lines, the Canadian Northern and the Great Northern, are building towards the valley. The vast region between the Rocky mountains and the Pacific coast, extending northward for several hundred miles from the international boundary, which has been the scene of extensive mining- and smelting-operations for many years, is filling up with settlers, who are attracted by the wealth of minerals and timber, the rich soil of the valleys, and the fine climate. The Nicola river, flowing westward through the valley of that name in the Yale district, discharges into the Thompson river, which is the eastern branch of the Fraser. The transcontinental line of the Canadian Pacific railway crosses the mouth of the Nicola river at Spence's bridge, 178 miles from Vancouver. From Spence's bridge the Nicola branch line ascends the valley for 40 miles to Merritt, the coal-center, and continues 7 miles farther to the town of Nicola. Thus the haul from the mines at an elevatioiz of 2,000 ft. to salt water is 218 miles down river-grades. The Nicola branch will be continued about 150 miles farther eastward to Penticton, where it will connect with an extension of the line through the rich Kootenay and Boundary districts. The Canadian government has granted a subsidy of $6,000 per mile, to which the provincial government is planning to add $5,000 per mile, to assist in the construction of the Nicola extension. Upon the

Jan 1, 1910

By I. R. Taylor

Vanadium has recently joined the growing list of mineral commodities being exploited by surface mining methods. Union Carbide Corp. controls several vanadium deposits in central Arkansas near the city of Hot Springs in Garland County and the community of Magnet in Hot Spring County (Fig. 1). Two open pit mines, located approximately five miles southeast of the city of Hot Springs in the Wilson Springs area, have been developed for production during the past two years. Adjacent to the mining area the company has recently completed a 1,600-ton-per-day (tpd) processing plant to treat the Wilson Springs and Magnet Cove ores (Fig. 2). Although this operation constitutes the largest vanadium mining project in the United States, the open pit mines are of moderate size. A number of small to medium-sized surface mines will be developed during the life of the operation. This chapter describes the methods and practices used to bring these recently discovered vanadium deposits into production. PRELIMINARY EXPLORATION The vanadium potential of the deposits near Hot Springs and Magnet Cove was first investigated by Union Carbide Corp. in 1960. These areas have long been of interest for their varied mineral content and were previously explored by government agencies and private interests for titanium, columbium, molybdenum, and uranium. No sustained operations resulted from this early work, although the rutile deposits of Magnet Cove were worked intermittently between 1911 and 1944.l Significant vanadium concentrations were reported in a U.S. Bureau of Mines publication describing the investigation of a titanium prospect

Jan 1, 1969

By Spencer Cragoe

I have read with much interest the elaborate and able paper of Messrs. Granger and Treville on the Mining Districts of Colombia, presented at the Atlantic City Meeting (ante, p. 33). Going into detail, however, as the paper does—and particularly with reference to the department of Antioquia, I am somewhat surprised that the property of the Frontino and Bolivia Company, probably one of the richest and most extensive in Colombia, should come off with such scant notice. The entire property embraces an area of some 28 square miles, and is situated at a distance of about 2 leagues from Remedios—after Medellin probably the most important town of the Department—and lying in approximately '7° N. latitude. The neighborhood of Remedios has been long celebrated for its production of the precious metal. Alluvial gold in large quantities has been obtained from the vicinity for upwards of two centuries; and even to-day a large proportion of the population finds a comfortable livelihood, during the dry season, in washing the sands of various rivers, notably the Rio Porce; while the amount of gold, in the form of nuggets, brought almost daily to Remedios and other points, from streams in the immediate neighborhood, is astonishing. These nuggets vary much in size. The majority, of course, are small, but larger ones are by no means scarce. I have been considerably surprised at the amount and value of the trade thus transacted between natives and merchants of the various towns. The property owned by the Frontino and Bolivia Company has been, I believe, for the larger part of the present century,

Jan 1, 1899

Alfred C. Young† (communication to the Secretary): Before the appearance of Mr. Scott's paper in these Transactions we were not specially interested in the investigation which he has started; but at his request we have endeavored to collect from musty records and the recollection of our old friends a brief chronicle of the progress made by this house. As 3000 instruments were manufactured by us before any descriptive record was kept, and 2000 more before the record contained more than a statement whether the instrument was a transit or a level, and sometimes its size, we approach the task with timidity, trusting that the reader will bear the difficulties in mind, particularly as the writer's predecessors, from whom, no doubt, the information desired could have been obtained, have passed away. Instruments for surveying were manufactured by David Rittenhouse, of Philadelphia, as early as 1760; but it was not until late in the first quarter of this century that there was any American market for an instrument outside of the ordinary surveyor's compass. With the advent of canals and railroads, and the more extensive development of the Pennsylvania coalfields, arose a demand for surveying-instruments to meet problems in engineering beyond the limited field of the compass. On May 1, 1820, in which year the practical mining of anthracite coal in Pennsylvania began, William J. Young, who had served his apprenticeship with one Thomas Whitney,

Jan 1, 1901

By E. T. Dumble

For many years there have been occasional reports of the discovery of gold from a belt of the coast country of Texas which is underlain by deposits belonging to the lower Eocene. For the most part they have been treated as newspaper reports and no examination or record of them has been made. Among such, it may be mentioned that in 1896 there was a flurry over reported gold-discoveries west of Luling and elsewhere in this belt, and in 1903 some prospect-shafts were sunk on the Gon-zales branch of the Galveston, Houston & San Antonio railway, 3 miles below Harwood. During 1912, further discoveries have again brought the matter to our attention, and it may be of interest to record the facts as we have found them. Some years ago specimens were sent me, which were said to have been taken from certain beds on Gazley creek, and concentrated by washing in a rocker. In them were several particles of gold sufficiently large to be visible to the eye. Under the microscope they showed to be, with few exceptions, sharp cornered, and not rounded as is usual with placer-gold. They were not filings, however, but their sharpness seemed rather to be due to a recent freeing from their matrix. One or two grains were rusty, and one copper-hued, but the most of them were tolerably bright. On examining the material of the samples small grains or fragments were found, of a yellowish brown color, which seemed to be of a finely-granular structure—possibly a sandstone. In these fragments I found particles of gold, one of them being large enough to be visible without a lens. Gazley creek empties into the Colorado river just north of Smithville, and for a few miles north of that place its banks show, beneath the deposits of more recent materials, the sands and clays of the Lignitie division of the Eocene, with lignite, shells of iron, etc.

Jan 1, 1913

By J. S. Kasper, R. M. Waterstrat

IN view of the recent findings of a pronounced ordering of atoms in s phase alloys containing elements of the first long row of the periodic table (and including molybdenum),l it is of interest to resolve the question of ordering for s phases containing second and third-row elements. Examples of the latter have been provided recently by Greenfield and Beck2 and two of them, Re-Cr and Ru-Cr, would appear to be favorable for a study of ordering by X-ray diffraction methods because of the considerable differences in the scattering factors concerned. In addition, s phase is found to occur in the Os-Cr system, where the difference in scattering factors is even larger. Accordingly, X-ray powder intensities have been measured in an attempt to learn the nature of the ordering, if any, in these three v alloys. Since there is no reported work on intermediate phases in the Os-Cr system, an exploratory investigation was made in this system, and it was found that, in addition to the s phase, the phase with the A-15 or ß-W structure also occurs. Specimen Preparation—The alloys were prepared by compressing mixed powders of —200 mesh size and sintering in an atmosphere of pure dry hydrogen. All alloys were rapidly cooled from the annealing temperature to room temperature in a stream of cold dry hydrogen in a water-cooled chamber. Table I lists the sources and purities of the starting materials, as well as the details of processing for each of the alloys investigated. Intermediate Phases in the Os-Cr System—In the absence of information on intermediate phases in the Os-Cr system, it was suspected that this system would resemble that of Ru-Cr, where a s phase, RuCr2,2 and a phase with the A-15 structure, RuCr3,3,4 have been identified. Both these phases were found in the Os-Cr system and at compositions

Jan 1, 1958

By E. G. Deane

A METHOD of top slicing has been devised at the Miami Copper Co.'s mine at Miami, Ariz., which differs radically in some ways from the customary methods of top slicing. The area of that section of the orebody in which top slicing is used is about 800 ft. square. The ore, while for the most part soft, is, nevertheless, considerably harder than the capping. The latter is siliceous, seldom containing any clay or other binding material, and breaks into fine particles so that it runs like sand if given the opportunity. Because of these facts, and because the ore is above the average grade of the mine ore, it has been mined by top slicing. Haulage levels are opened up 150 ft. apart, vertically, with two sublevels between at 50-ft. intervals, to facilitate the building of ore chutes. These sublevels are used during slicing for distributing air in the ventilation system. On the haulage level the drifts are spaced on 50-ft. centers, and raises along these drifts are also spaced on 50-ft. centers, except the incline raises as hereafter noted. The raises are cribbed where necessary. Where the wear will be excessive, ¼ -in. iron plates are spiked to the top of every third set of cribbing, for its protection. When top slicing was first used, an attempt was made to carry a slicing face from fifty to several hundred feet long. Timber and other, supplies were brought in through long drifts from an auxiliary shaft. Great difficulty was experienced in keeping these drifts open, the side pressure breaking the posts and the top weight breaking, both caps and posts. Furthermore, the men could not work efficiently while these drifts were .being repaired. The slicing faces advanced irregularly, due to varying conditions, and in many ways the results were not all that could be desired. It was then decided to divide the slicing area into blocks 200 ft. square and this wins later changed to 250 ft. square.

Jan 9, 1916

By J. S. Miller

THIS paper describes the method of mining a steeply pitching anthracite seam on a heavy pitch in the Orchard vein in No. 1 Tunnel of the Lehigh Coal and Navigation Co. The Orchard vein in the Nesquehoning district has a thickness of about 15 ft. on the level of the gangway, which is sufficient thickness for the gangway to be driven full width in coal. Above the gangway, the vein becomes thinner and near the surface is about 8 ft. thick. The coal is of good hard quality and carries a fairly good roof. The pitch of the vein is between 65° and 70°. Usually the breast-and-pillar method has been employed in the mining of the steeply pitching veins in this section. This method produced good results as far as the mining of the breast was concerned but the recovery of the pillar was difficult as to full extraction and expensive as regards costs. To recover these pillars after the breasts were driven, three methods were commonly employed; they were known as the pillar-breast method, pillar-skipping method, and pillar-chute method. The pillar-breast method consisted in putting a battery in one corner of the pillar (Fig. 1), coupling the manways A and B of the two adjacent breasts for two or three lengths ahead of the working face of the pillar being cut, and working the pillar as a breast. This method was used by the more skilled miners of the earlier days but has practically been abandoned. A slight variation of this method is used to some extent. In this case, the pillars are left wider than ordinarily and of sufficient width for the full-width breast to be driven in and a small pillar left on each side of the pillar breast between it and the regular breasts. With the completion of the "pillar breast," the ribs are drilled full of holes, loaded, and fired.

Jan 3, 1925

By S. Skowronski

The melting of cathode copper, ususally containing 95.98+ per cent. • Cu, would appear to be a simple matter. Owing to the well known affinity of copper for sulfur, however, so much sulfur is absorbed by the copper during the operation that a long and expensive refining process is required to remove it, and the final product is inferior in purity and lower in electrical conductivity than the original cathode copper. The furnace operation, as now conducted, includes the following stages: 1. Charging the cathodes into the furnace. 2. Melting the cathodes. 3. Oxidizing period—saturating the copper with cuprous sub-oxide and bringing the metal to the condition known as "set copper;'' this is now done by blowing air into the molten bath of metal. 4. Reduction period, otherwise known as "poling," whereby the oxygen previously added is removed by covering the molten bath completely with coke or charcoal and introducing large poles of green wood; this reduces the cuprous sub-oxide, bringing the copper to the "tough pitch" stage ready for casting. 5. Casting Period. Many experiments have been made to obviate the long periods of oxidation and subsequent reduction, with no success. While the copper first cast will be good, as indicated by the set surface of the bars, it is impossible to hold it to the "tough pitch" condition, and long before the whole charge has been poured the copper will become "overpoled," entailing numerous difficulties. Sulfur has always been blamed by the furnace men as the reason why this refining process is necessary, yet the literature on the subject does not sufficiently emphasize how small a proportion of sulfur will ruin copper for practical purposes. The sulfur absorbed by copper during the melting period comes from two sources: (1) the sulfate left on the cathode sheets in the tank houses; (2) the fuel. The percentage of sulfates on the cathodes is variable, and depends on the care taken in washing the cathodes after removing

Jan 1, 1919

H ORACE VAUGHN WINCHELL was born at Galesburg, Michigan, Nov. 1, 1865, and died at Los Angeles, California, on July 28th of this year, at the age of fifty-seven. Mr. Winchell was one of the conspicuous geologists of his time. It may fairly be said that he was a geologist born and reared. His father, N. H. Winchell, was professor of geology at the University of Minnesota; his uncle, Alexander Winchell, was professor of geology at the University of Michigan. Under both of them Horace studied, graduat-ing at the University of Michigan in 1889. Mr. Winchell at once began that active life in the field which he followed for 34 years and until his death. The first years of his professional life were largely spent in the study of the iron ranges of Min-nesota. In 1898, he re-moved to Butte and became geologist in charge of the geological depart-ment of the Anaconda Copper Mining Co. and allied companies. There he remained for eight years. This period covered the trying days of the mining controversies be-tween the Anaconda and associated companies and the Heinze interests, and it fell to Mr. Winchell to direct the geological studies and development in connec-tion with that litigation. Recognizing the importance of careful geological study in the practical operation of mines, he organized and developed the splendid geological department of the Anaconda Copper Mining Co. This was one of his greatest contributions to the mining industry. Probably no mining company has attached the impor-tance to geological study and continuity of geological mapping in connection with mining operations that the Anaconda company has. It has given broad authority to its geological department and the development of its mines is under the direction of its geologists. The broad vision of Mr. Winchell was responsible for the adoption of this policy, one which is being profitably employed by many other organizations.

Jan 9, 1923

The editorial expenses for the preparation of the manuscript of the second edition, as for the first, were provided by grants of the Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME ; the Seeley W. Mudd Memorial Fund again sponsored the publication of this volume. The companies and research or educational institutions with which the authors, reviewers, and editors are connected also contributed much to the writing and editing of this book through their generous donations of time and travel and office expenses. And finally, the authors and others have given countless hours of their own time with no recompense but the satisfaction of a job well done. In order to give credit to the companies or educational institutions which made it possible for the members of the Editorial Board to devote considerable time to the revision of this book, the names of these members and their affiliations are recorded here as follows W. O. Philbrook, Carnegie Institute of Technology M. B. Bever, Massachusetts Institute of Technology H. B. Emerick, Jones and Laughlin Steel Corporation B. M. Larsen, United States Steel Company A number of individuals suggested desirable changes in the book before rewriting was started. Almost all manuscripts were gone over critically by reviewers, and the resulting criticisms led to the correction of errors and omissions and greatly contributed to the accuracy and completeness of the text. Other people have supplied additional data or illustrations or assisted in other ways. While some of these contributors must remain anonymous because they are not known to the Editors, the cooperation of the following individuals is gratefully acknowledged: R. D. Allen, Republic Steel Corporation, Chicago Isadore Amdur, Massachusetts Institute of Technology Mary Baeyertz, Armour Research Foundation S. P. Bahmer, Republic Steel Corporation, Massillon E. C. Bain and Associates, United States Steel Company, Pittsburgh C. W. Briggs, Steel Founders' Society of America H. W. Briske, Wisconsin Steel Works

Jan 1, 1951

By H. Vance

In 1932, as in 1931, the East Texas area outside the Gulf Coast exerted ' its influence over the entire petroleum industry. Practically 60 per cent of the oil wells completed in the United States during 1932 were in this area, development being chiefly confined to the East Texas oil field in Upshur, Gregg, Rusk, Smith and Cherokee counties. This East Texas area is geologically an interior salt dome basin, along the western edge of which are located the fault line fields as represented by Mexia and Powell. Production occurs on salt domes in the interior of the basin as represented by Boggy Creek and possibly Van, although no salt has actually been discovered in drilling at Van. Shore line conditions on the east side of this basin along the flanks of the Sabine uplift have been responsible for the East Texas oil field. Many known salt domes in the center of this basin have been tested but as yet have failed to produce oil in commercial quantities. The main producing horizon throughout the area is lowermost upper Cretaceous and is known locally as the Woodbine sand. The East Texas Oil Field Development.—Approximately 6000 producing wells were completed during the year in the East Texas oil field. No accurate estimate of the total initial production of these wells is available because few initial production tests were made as the wells were completed. The writer estimates the average initial production of these completed wells at 2500 bbl. per day while flowing wide open through tubing. Based on this estimate, the total initial production of the wells completed during the year is 15,000,000 barrels. At the close of 1932 there were approximately 9500 completed wells in the East Texas field. Of this number 176 were without pipe line connections. The oil produced from these unconnected wells could be marketed for $0.30 per barrel while the price paid for oil run from the connected wells was $0.75 per barrel.

Jan 1, 1933

BECAUSE you cannot always proceed by the ordinary pathway since you sometimes find yourself in a place where you cannot have all that you might need or wish, it often happens that it is necessary to know how to recognize and understand your materials well, in addition to having them well disposed, and to know how to use your, ingenuity in arranging a mould., Furthermore, things have a great diversity among themselves, and it is not possible to give a particular rule for all. But if you have a certain broad fundamental knowledge when you have need of many things, the ingenuity awakens and supplies its needs by imitation. Now, because I have thought that you had not hitherto had the slightest shadow of knowledge of what I have described in this treatise of mine, I have expanded and narrated things in greater detail than perhaps I might have done. For this reason I have also decided that I wish to tell you of several methods that can be used if you wish to mould, especially in making an intaglio* for a relief, t or in making another intaglio in bronze from either an intaglio or a relief. And I will tell how every relief reduces, itself from convex to concave and also how the relief is made from the intaglio. These works are first made of plaster or pastes or some other liquid thing that is soft when moulded and becomes hard either by drying out with heat or by shrinking with cold, such as tragacanth, plaster of Paris, sulphur, lead, wax, or similar things. And, in conclusion, we describe the method of making an intaglio from a solid. In making an intaglio you must first consider whether it is a large or small thing, figure or foliage, whether it is in demi- or bas-relief, and whether it is a thing that projects from the mould wholly or in part.

Jan 1, 1942

By M. H. De Hora

(Butte Meeting, August, 1913.) IN giving my opinion of the importance of Colombia as a field for investment for those interested' in mining for the precious metals, I must begin by quoting Sir Clement Markham, who, in one of his presidential addresses to the Royal Geographical Society of Great Britain, called the attention of its members to the fact that " although Colombia is the least known and least developed of the South American republics, it is far and away the richest mineral country of them all." This to American investors is extremely interesting, as the country is the most accessible of all the South American republics from the United States. .Almost all of the gold shipped by the Spaniards from Madre de Dios, now Colon, came from Colombia, and statistics from the Mint at Medellin, the capital of the Department of Antioquia, go to show that the . total production of the precious metals of Colombia, dating from the Spanish conquest in the fifteenth century to the present time, aggregates the enormous total of $700,000,000. Of this amount, nearly 70 per cent. represents gold obtained from the placers of the Republic, more than one-half of which came from the Department of Antioquia, the balance, being divided between the placers of the Choco and the rest of the Republic. The remaining 30 per cent. of the $700,000,000 represents the silver and gold obtained from the quartz mines, the silver greatly predominating. A glance at the map of Colombia shows the territory somewhat in the shape of an outspread human left hand extended palm downwards on the paper, with the wrist adjoining the Republic of Ecuador, the bones of the hand, fingers, and thumb representing the divisions of the great Andean mountain chain known as the Cordilleras of Colombia. The first finger represents the Eastern Cordillera, with the thumb as the extension to the Nevada de Santa Maria, forming

Jan 7, 1913

By William Firmstone

ON the 19th December, 1833, a patent was granted to F. W. Geisenheimer, for smelting iron ore with anthracite. In his claim he says: "Sixthly, though I cannot, and do not, claim am exclusive right of the use of heated air, for any kind of fuel, nevertheless I believe to have a right to claim the use of heated air, applied upon, and in connection with, the said principle and manner discovered by me, to smelt iron ore in blast-furnaces with anthracite coal, by applying a blast of air in such quantity, velocity, and density, or under such pressure, as the compactness, or density, and the continuity of the anthracite requires, as above amply and fully described and illustrated." Dr. Geisenheimer made experiments in smelting iron ore with anthracite at the Valley Furnace, near Pottsville, but he failed to carry out to good practical results the principles enunciated in his patent. In the Journal of the Franklin Institute for February, 1838, a communication was published that was made by Mr. George Crane, of the Yniscedwyn Iron Works, South Wales, to the British Association, in September, 1837. On the smelting of iron with anthracite coal, Mr. Crane states therein, that he began the use of an¬thracite with hot-blast on the 7th February, 1837, in a cupola blast-furnace, 41 feet high, and 10' feet across the boshes ; product, 34 to 36 tons a week. Mr. Crane goes on to say, "It may not be uninteresting to be informed in what matter the idea first occurred to me of applying a heated blast to anthracite coal. One evening, after I had placed a piece of it upon my parlor fire (which had before been made up with bituminous coal), and had allowed it to arrive at a red heat, upon applying as fierce a blast to this piece of coal as I could raise from a pair of bellows, I noticed a black spot or mark

Jan 1, 1875

By G. C. Wallick, W. R. Foster, J. G. Savins

The theory of the differentiation method for the Couette flow experiment is reviewed. Particular attention is given to the requirements on data analyses in the case of the class of non-Newtonian materials described as viscoplastics, i.e., materials characterized by a yield point or yield stress. Here changes in boundary conditions arise when the shearing stress attains a critical value with the result that the form of the basic integral equation for Couette flow is determined by the flow conditions existing during the measurement. INTRODUCTION In the preceding papers in this series,l,2 the salient features of the differentiation method of rheological analysis in Poiseuille-type flow were discussed. It was shown that a dual differentiation-integration method analysis of the Poiseuille flow of idealized generalized Newtonian and visco-plastic models could be used to develop a spectrum of highly sensitive response patterns in terms of certain characteristic derivative functions. These functions were shown to optimize the selection of the most appropriate functional relationship between f(p) and p from the Poiseuille flow experiment. The present paper reviews the theory of the differentiation method as applied to the equally important Couette flow experiment. We will also discuss the range of variables over which the basic integral equation for Couette flow is applicable when the non-Newtonian material is of the viscoplastic type, i.e., characterized by a yield point or yield stress. THEORY Having described the application of the differentiation method to Poiseuille-type flow in the preceding papers, we now proceed to the case where the test liquid is confined to the annular space between coaxial cylinders of length L, one of which is in motion, i.e., Couette flow, formulating the basic integral equation after the method of Mooney.3 The observed kinematical and dynamical quantities are the angular velocity O and the torque T. Here, the one nonvanishing component of the shear-rate tensor is

By D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, Ill. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation was removed. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow readings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through wet washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main was fabricated from riveted sheets led us to discard the idea of using Pitot tubes for this service. The Venturi tube was then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made.

Jan 2, 1921