Search Documents

By P. E. Fitzgerald, Dana G. Hefley

An apparatus has been developed which permits selective acidizing of producing formations and determination of the relative permeability of a formation by fluid injection. This apparatus, known as the "Electric Pilot," is an electrical fluid-interface locator, the electrical circuit of which is completed when the elec-tcodes in the well are in contact with a conductive fluid, but is not completed when immersed in a nonconductive fluid. Results are given for a number of typical acidizing applications in which the interface locator was used to control the acid. Description of the method used in making a permeability survey and the data obtained are also included. Introduction Early in the development of the acidizing industry it was recognized that one of the most important problems to be solved in the chemical treatment of any well was the determination of what part of the exposed section in the well should be treated and the selection of the technique that would insure treatment of the desired section. One of the first techniques adopted for assisting in proper placement of the acid, which is still widely used, is the method of confining the acid to the producing section by means of a column of oil, which is known as the Carr1 method of treatment, named for its inventor. In the Carr method it is not possible to selectively acidize a specific horizon in a multiple pay zone, so many improvements and modifications of the basic Carr technique were devised to accomplish this result. In order to overcome the possibility of the acid entering an undesirable section at the bottom of the well, organic gel plugs2 were introduced into the bottom of the well, which served to halt the entrance of the treating solution into these zones.3 These chemical gels later liquefied because of bacterial action and were removed from the well with the produced fluid. In fields where a gas cap existed, as in the Goldsmith field of Ector County, Texas) it was imperative that a treating technique be evolved that would confine the acid to the oil-producing zone below the gas cap. By so doing the oil-productive capacity of the wells could be improved without greatly increasing the gas production and this would lower the gas-oil ratio of the well. ~h, technique employed4 to achieve this effect utilized two pumps, one for pumping the chemicals down the tubing, the other to simultaneously force oil down the annular space to confine the acid to the oil pay, thus preventing the chemicals from entering the upper gas-bearing zones. Experience has indicated that gas wells and certain types of oil wells respond better to ''stage treating.'' This technique utilizes the introduction of a certain volume of acid and then allows the well to ''clean up99 before introduction of the next and usually successively larger stages. Where such methods are employed steps must be taken to keep a disproportionate share of the acid from entering the most permeable and previously treated Zones. A special tool

Jan 1, 1944

By M. M. Slotnick

It was once aptly said that a sign of approaching senility is ceasing work on a subject and beginning to talk about it. Perhaps that explains why, after many Years in which Part of my duties has been the training of college men in various branches of petroleum exploration geophysics, I have now begun to talk about it. In making an outline of what I believe ought to be discussed under the general heading of the title, I found it almost impossible to subdivide the ideas into an ordered set of discrete subjects. Rather, the pertinent remarks seemed to interlock almost everywhere. The consequence is that it will be necessary to start with the conclusions and then try to justify them by jumping back and forth. However, based on the types of men with whom I have had to deal, the subject naturally divides itself into two parts. In the first part, I should like to deal with the case of those undergraduates whose natural bent is toward the physical sciences and who may decide to enter the geophysical fold as a career. The other part will deal with those many men, geologists and engineers for the most part, who have drifted into exploration geophysics by one means or another, and whom it is necessary to train for geophysical work while they are occupied in their routine jobs. Here it may be in point to remark that most men in exploration geophysics at Present have been developed from precisely the latter group, and that the problem of training here is of great importance even though, in this paper, it will perforce occupy the secondary place. Training oF a Geophysicist The outstanding reason for the perplexing problem on the training of a geophysi-cist is that ideas differ on the answer to the question: "what is a geophysicistp" ln any of the scientific "specialties," like physics, for example, it is relatively simple to pigeonhole a man as being qualified to call himself a physicist. That appellation applied to an individual does not mean that he has mastered only the branches of intellectual endeavor usually associated under the broad name of "physics." we expect him also to have a more than mere acquaintance with mathematics and chemist~ and some understanding of most of the other sciences. But note this important point—we expect our physicist, whom we have chosen as an example, to be intelligently trained so that, if necessary, he can and will know how and where he can get the proper information on a subject in which he is not a specialist; he will know how to absorb that information and turn it to his uses. It seems to me that this is the outstanding characteristic of a man who can truly call himself a scientist: that he is a specialist in one of the broad branches of science in that he has enough training and discipline in the scientific approach so that, when called upon to do so, he can inteugently absorb knowledge from another bordering science (and all sciences not only border upon one another to some extent, but more often, overlap One another), and

Jan 1, 1946

By M. M. Slotnick

It was once aptly said that a sign of approaching senility is ceasing work on a subject and beginning to talk about it. Perhaps that explains why, after many Years in which Part of my duties has been the training of college men in various branches of petroleum exploration geophysics, I have now begun to talk about it. In making an outline of what I believe ought to be discussed under the general heading of the title, I found it almost impossible to subdivide the ideas into an ordered set of discrete subjects. Rather, the pertinent remarks seemed to interlock almost everywhere. The consequence is that it will be necessary to start with the conclusions and then try to justify them by jumping back and forth. However, based on the types of men with whom I have had to deal, the subject naturally divides itself into two parts. In the first part, I should like to deal with the case of those undergraduates whose natural bent is toward the physical sciences and who may decide to enter the geophysical fold as a career. The other part will deal with those many men, geologists and engineers for the most part, who have drifted into exploration geophysics by one means or another, and whom it is necessary to train for geophysical work while they are occupied in their routine jobs. Here it may be in point to remark that most men in exploration geophysics at Present have been developed from precisely the latter group, and that the problem of training here is of great importance even though, in this paper, it will perforce occupy the secondary place. Training oF a Geophysicist The outstanding reason for the perplexing problem on the training of a geophysi-cist is that ideas differ on the answer to the question: "what is a geophysicistp" ln any of the scientific "specialties," like physics, for example, it is relatively simple to pigeonhole a man as being qualified to call himself a physicist. That appellation applied to an individual does not mean that he has mastered only the branches of intellectual endeavor usually associated under the broad name of "physics." we expect him also to have a more than mere acquaintance with mathematics and chemist~ and some understanding of most of the other sciences. But note this important point—we expect our physicist, whom we have chosen as an example, to be intelligently trained so that, if necessary, he can and will know how and where he can get the proper information on a subject in which he is not a specialist; he will know how to absorb that information and turn it to his uses. It seems to me that this is the outstanding characteristic of a man who can truly call himself a scientist: that he is a specialist in one of the broad branches of science in that he has enough training and discipline in the scientific approach so that, when called upon to do so, he can inteugently absorb knowledge from another bordering science (and all sciences not only border upon one another to some extent, but more often, overlap One another), and

Jan 1, 1946

By D. H. Woodard

One of the principal uses of polarized light in metallurgy is to show the granular structure of metals by contrasting reflections. This use is confined largely to anisotropic metals, such as beryllium, tin, magnesium, and the like.1 Recently, Hone and Pearson2 have extended the use of polarized light to include the isotropic metal aluminum. This was made possible by the formation of an anodic film that was optically anisotropic and that had a fixed and reproducible structural relationship to the grains in the substrata. With their method, it was possible to indicate localized textures in annealed aluminum sheet. In the course of an investigation of plastic deformation at the National Bureau of Standards, it was found that the isotropic single phase alloy Monel could be made optically anisotropic by treatment with the usual Monel contrast etchant. Experiments soon showed that dif- , ferences in orientation could be detected easily. Previous investigations involving the use of polarized light have been restricted to annealed metals. In this paper it will be shown that inhomo-geneous plastic deformation which results in lattice bending and development of deformation bands, experienced by individual grains in polycrystalline Monel, is revealed in the microstruc-ture. This interpretation of the micro-structure was confirmed by a study of slip lines formed after prior plastic strain. Materials and Procedure The material used was Monel, the chemical composition of which was C—0.17 pet, Mn—1.28 pet, Fe—1.61 pet, S—0.009 pet, Si—0.17 pet, Cu— 30.70 pet, Ni—66.04 pet. The material was divided into 2 lots which were treated as follows: Lot A was heated at 1700°F for 3 hr to produce a fully annealed, coarse grained structure. Lot B was heated at 1400°F for 1 hr to produce a close approximation of a fully annealed structure without appreciable increase in the grain size of the original material. After each of these heat treatments the material was cooled in air. Samples for metallographic examination were cut from tensile and compression test specimens and were prepared by grinding on lead-tin laps, followed by electrolytic polishing, † Etching and the development of ridges were avoided by keeping the voltage above 3.8 and by preventing contamination of the polishing solution with water. Monel, when polished and treated with most etchants, is optically isotropic. However, when given a light etch for about 4 sec with the Monel contrast solution the surface of the metal becomes optically active. The microstructure when observed under crossed nicols* appears different from that viewed by ordinary light. This is shown by a comparison of micrographs made of the same area of a plastically deformed specimen using polarized light (Fig la) and white light (Fig 16). If Monel, which has been lightly treated with the contrast etchant, is slightly deformed by compression, rectangular figures are apparent over the specimen. However, within too short a period to be photographed, these rectangles become circular, probably because of surface tension effects within the etched film. The two observations,

Jan 1, 1950

By P. E. Fitzgerald, Dana G. Hefley

An apparatus has been developed which permits selective acidizing of producing formations and determination of the relative permeability of a formation by fluid injection. This apparatus, known as the "Electric Pilot," is an electrical fluid-interface locator, the electrical circuit of which is completed when the elec-tcodes in the well are in contact with a conductive fluid, but is not completed when immersed in a nonconductive fluid. Results are given for a number of typical acidizing applications in which the interface locator was used to control the acid. Description of the method used in making a permeability survey and the data obtained are also included. Introduction Early in the development of the acidizing industry it was recognized that one of the most important problems to be solved in the chemical treatment of any well was the determination of what part of the exposed section in the well should be treated and the selection of the technique that would insure treatment of the desired section. One of the first techniques adopted for assisting in proper placement of the acid, which is still widely used, is the method of confining the acid to the producing section by means of a column of oil, which is known as the Carr1 method of treatment, named for its inventor. In the Carr method it is not possible to selectively acidize a specific horizon in a multiple pay zone, so many improvements and modifications of the basic Carr technique were devised to accomplish this result. In order to overcome the possibility of the acid entering an undesirable section at the bottom of the well, organic gel plugs2 were introduced into the bottom of the well, which served to halt the entrance of the treating solution into these zones.3 These chemical gels later liquefied because of bacterial action and were removed from the well with the produced fluid. In fields where a gas cap existed, as in the Goldsmith field of Ector County, Texas) it was imperative that a treating technique be evolved that would confine the acid to the oil-producing zone below the gas cap. By so doing the oil-productive capacity of the wells could be improved without greatly increasing the gas production and this would lower the gas-oil ratio of the well. ~h, technique employed4 to achieve this effect utilized two pumps, one for pumping the chemicals down the tubing, the other to simultaneously force oil down the annular space to confine the acid to the oil pay, thus preventing the chemicals from entering the upper gas-bearing zones. Experience has indicated that gas wells and certain types of oil wells respond better to ''stage treating.'' This technique utilizes the introduction of a certain volume of acid and then allows the well to ''clean up99 before introduction of the next and usually successively larger stages. Where such methods are employed steps must be taken to keep a disproportionate share of the acid from entering the most permeable and previously treated Zones. A special tool

Jan 1, 1944

By D. J. Blickwede

PRESENT knowledge of the effects of time and temperature upon stabilization of the austenite-martensite reaction in steel is fairly complete,1-3 but at the time the work described herein was initiated there was no information about the effects of alloy elements on the phenomenon. However, it has been assumed on theoretical grounds that alloy elements, particularly carbide formers, may have a significant effect on stabilization.' The present work was undertaken to provide information about the effect of two common elements, nickel and molybdenum, on stabilization in hypereutectoid and hypoeutectoid steels. Seven induction-furnace melted, 1.2 pct C steels ' with a variation of nickel from 0 to 6 pct and of molybdenum from 0 to 1.0 pct were used for most of the experiments. Along with these a series of 0.4 pct C steels containing 0 to 6 pct Ni were also studied. The chemical compositions of the steels are listed in Table I. Stabilization in these forged, hot-rolled, annealed, and centerless ground steels was measured by aging brine-quenched specimens (aus-tenite temperature, 1800°F) at 95" and 150°F and then determining the change in specific volume produced by subsequent cooling from room temperature to —320°F.³ In presenting the results the decrease in the change in specific volume, ?V, after various stabilization times is used. This is given by ?V -= ?VO - ?V1 where AVO is the change in specific volume on quenching directly to —320°F and aV, is the change in specific volume on quenching to —320°F after stabilizing for time t. In other words, ?V is a direct measure of the amount of martensite that is lost to the subzero quench as a result of stabilization and hence is greater, the longer the aging time or the higher the aging temperature. The results are shown in Fig. 1. The scatter of the data, which are not shown for clarity and brevity, was sufficient to make the relative location of the curves on the ?V axis inaccurate within ±2x10-5 cc per g. However, some generalities appear which are of interest. Effect of Nickel In the 0.4 pct C steels, up to 3 pct Ni has little, if any, effect on the rate or amount of austenite stabilized at 95°F, Fig. la. Increasing nickel from 3 to 6 pct almost doubles the amount of austenite stabilized in a given time. In the 1.2 pct C steels aged at 95°F, increasing the nickel from 1 to 3 pct appears to decrease the amount of stabilization, and a further increase to 6 pct Ni completely eliminates stabilization as shown in Fig. lb (M, of 6 pct Ni steel was below room temperature). The same behavior was exhibited by these steels stabilized at 1500°F, especially after aging for periods longer than 5 hr, Fig. lc. Thus it appears that up to 1 pct Ni has little effect on stabilization at low or high carbon levels. More than 1 pct Ni increases stabilization at low carbon contents and decreases it at high carbon contents. Ward, Jepson, and Rait5 have found that at inter-

Jan 1, 1954

THE activity of the principal oil fields of Rumania followed the same course as in 1939. It was marked by (1) collaboration between the various companies, particularly in exploiting oil at great depths with a view to rationalizing the exploitation and decreasing the difficulties inherent in very deep drilling; and (2) economy in the exploitation of the older pools in reducing to a minimum the cost of the extraction and working over of wells by the concentration of productive wells in groups. The pooling arrangement continued at Tintea as a measure of conservation, and exploitation of the unitized region went forward on the basis of the norms established in 1939. The same methods were applied in the fields of Liesti, Ceptura and Boldesti. The petroleum industry had some difficulty in providing the necessary material and the hands for work. Importation of material and machines from the United States was virtually stopped. Substitutes were provided from Germany but particularly useful were certain dispositions made by the local metallurgical industry. Despite the higher cost of the production of local material and machines, they were superior to the German product, the difference in quality justifying the higher price charged as the materials were found to be particularly adapted for the purposes of the petroleum industry. The cost of production was still further raised by the work that was imposed for national defense. The rise in costs per meter drilled was 50 per cent over those of 1939. According to bimonthly tables furnished by the Moniteur du Petrole Roumain, the deepest well completed in 1940 was an exploratory well, No. 201 of the Concordia company, drilled at Tintea and suspended at 3338 meters. This depth was reached toward the close of 1939 and the well was not deepened in 1940 became of large deviation from the vertical. The record for productive wells had been held by No. 429 at Tintea, drilled by Unirea to a depth of 3200 m., and in 1938 well No. 317 Cocorasti-Mislea, of the Colombia company, but these records were passed in 1940 by well No. 613 Liliesti of the Con-cordia company, which reached a depth of 3294 m. and had an initial production of 10 tons per day. In 1940, the same number of wells, II, had been drilled to a depth of over 3000 m. as in 1939. Five of these wells are at Tintea and six at Liliesti. Table I lists these very deep holes in the order of their depth. Table i.—Deep Wells Drilled in Rumania in 1940 Initial No. Produc- of Company Field Meters tion, Well Meters Tons per Day 405 Colombia......... Liliesti 3,001 10 629 Unireu............ Tintea 3,005 73 426 Unirea............ Tintea 3,050 48 410 Colombia. ........ Liljesti 3,055 30 627 Concordja (Unirea). Liliesti 3,072 75 430 627ConcordjaConcordia (Unirea). (Unjrea 3,II9 30 618 Colombia......... Liliesti 3,168 70 24 Steaua Romana. . . Tintea 3,184 18 412 24Unirea............ Tintea 3,211 23 613 Concordia......... Liliesti 3,294 10 Production in Rumania in 1940 reached 5,813,000 tons, in contrast to 6,~40,0oo tons in 1939, a decline of 427,000 tons, or 6.8 per cent. Drilling reached 241,500 m., in

Jan 1, 1941

By C. L. T. Edwards

In the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on Ioo per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blastfurnace charge as good iron as that made without scrap—made with straight ore?" This question may he answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on Ioo per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. Operation with ioo PeR Cent Steel Scrap During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a Ioo per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when Ioo per cent steel turnings were charged. Except for occasional charges of nickel scale as an "cxtra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore—ore and scrap—operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from Ioo per cent scrap to the regular burden, the charge I hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap ' charge. The furnace employed had a hearth 16 ft. o in., bosh 22 ft. o in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter in., bosh angle 73' 27' and a Balrer-Neuman top, with gas-engine blowers. Analyses Range of material charged Gravel: SiO2, 64.40 to 70.54 per cent; A1203, 3.52 to 4.58; CaO, 7.27 to 9.49; MgO, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83. I

Jan 1, 1942

By J. Szekely, R. G. Carr

A method is presented which allows the extension of the Ergun equation for the description of gas flow through packed beds in a nonisothermal regime. The pressure profile in the packed bed is calculated by the establishment of a differential energy balance and the iterative integration of the integral equation thus obtained. The predicted values of the pressure distribution were found to be in excellent agreement with those measured experimentally, under carefully controlled conditions. MANY metallurgical processes are carried out in systems in which a gas stream and particular solids are contacted in a packed bed arrangement under strongly nonisothermal conditions. Ore sintering, the firing of pellets, the operation of regenerators, blast furnace technology may be quoted as examples. Although many aspects of these systems have been extensively studied, an important variable, the pressure distribution and the relationship between pressure head and flow rate, received only little attention to date. The purpose of the paper is to present a brief survey of relevant previous work, followed by a more rigorously formulated model, together with experimental results that afford ready comparison of theoretical prediction with measurement. PREVIOUS WORK A great deal of information is available in the chemical engineering literature on flow phenomena in porous media.' The experimental results pertaining to gas flow were generally interpreted in terms of models based on the analogy with the flow through a pipe of an incompressible, isothermal fluid. Of the numerous, semiempirical correlations that have been proposed to relate pressure drop to the volumetric flow rate, the Ergun equation2 is generally regarded as the most satisfactory: The strong nonisothermality of the metallurgical systems previously mentioned would render the direct applicability of Eq. [I] rather doubtful as both density and viscosity are temperature-dependent. Ergun has used Eq. [I] for estimating the pressure drop in the stack region in the blast furnace by neglecting the viscous term and evaluating the gas density at the integral mean temperature.3 His calculations showed a rather variable agreement with measurements and it was uncertain whether the discrepancy found was attributable to the model or to the inaccuracies often inherent in measurements on an industrial scale. Other work on nonisothermal systems includes studies of the pressure distribution in sinter beds, notably by Voice et a1.4 and Mitchell.5 Mitchell developed a method involving the subdivision of the bed into several zones and assigning average property values (temperature, gas density, and so forth) to each zone. The pressure drop was then calculated for each zone by using an expression analogous to Eq. [I]. This method was an improvement over that described by Voice et al., but even here prediction and measurement differed by as much as 30 pct in certain cases. It would appear that no really satisfactory methods are available for the prediction of pressure drop in packed beds with a strongly nonisothermal regime. The method involving subdivision of the bed into small enough sections, that may be regarded as isothermal, would show promise; however its validity has to be tested by both a rigorous formulation and comparison with experimental data obtained under controlled conditions. In the following a formulation is presented together with experimental data allowing ready practical evaluation of the theory. FORMULATION The mechanical energy balance over an infinitesimal section of a packed bed may be written as follows:

Jan 1, 1969

By B. Ramaswami, Y. Nakada, R. Schaefer

EARLY investigations1 of the tensile properties of fcc single crystals did not reveal the easy glide region of crystals with axial orientations inside the standard stereographic triangle. With the production of high-purity metal, a region of easy glide became known1 Consequently, modern work of fcc single crystals ordinarily uses high-purity metal. In order to determine whether further purification of aluminum beyond 99.992 pct purity would result in significant alteration of the tensile properties of single-crystal specimens, metal was zone-refined and crystals grown from the purified material were compared to crystals grown from the original material. Some similar studies were made of gold and silver crystals. Aluminum. The material to be zone-refined was cast into bars 1/4 by 1/2 by 8 in. A zone, approximately 1-1/2 in. in length, was passed over each bar eighteen times at a rate of 6 in. per hr. Melting and stirring were carried out by an induction heater under a vacuum of approximately 10"5 mm Hg, the metal being held in a graphite container. he last 3 in. of each processed bar were then cut off and discarded. No quantitative determination of purity was made, but the effectiveness of the zone refining was tested by a method first suggested by Walton, Tiller, Rutter, and winegard3 depending on the relation between cell structure and impurity content. Rutter and Chalmers4 have shown that a cellular substructure is associated with the presence of impurities during solidificatibn, and have shown how solute rejection at the freezing interface can lead to such an association. Thus the observation of cells gives evidence of impurities being present. To look for cells, the last quarter of a zone-refined bar was cut off, remelted, and grown rapidly into a single crystal. It was then heavily electropolished and thermally etched.~ Cells were revealed by the presence of many parallel rows of etch pits. The same process was carried out with material from the first half of the bar, but no cells were detected. These observations give evidence that a significant amount of impurity material was moved to the "dirty" end of the zone-refined bars. Further indication of purification was obtained from recrystallization experiments. It was found that, after cold rolling to a 97 pct reduction in thickness, the material from the pure end of the bar re-crystallized at room temperature, but the material from the "dirty" end did not. Other investigators6 have previously reported that zone-refined aluminum recrystallized at room temperature. The purified material was cast into 1/4 by 1/4 in. bars, and seeded crystals were grown in a (100) orientation and in a single slip orientation where the Schmid factor is m =2. The crystals were then cut to the desired length, annealed for 24 hr at 610°C, furnace-cooled, and etched in Tucker's etch. The crystals were tested in a floor-model Instron machine, using a gage length of 4 in. and a strain rate of 1/2 pct per min. The resulting curves are shown in Fig. 1. It is seen that the differences between the curves for zone-refined and original-purity materials are small. These differences are within the scatter observed for crystals of the original purity. In particular, the zone refining does not significantly affect the onset of the different "stages" of the curves.

Jan 1, 1964

By C. L. T. Edwards

IN the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on 100 per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blast-furnace charge as good iron as that made without scrap-made with straight ore?" This question may be answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on 100 per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. OPERATION WITH 100 PER CENT STEEL SCRAP During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a 100 per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when l00 per cent steel turnings were charged. Except for occasional charges of nickel scale as an "extra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore-ore and scrap-operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from i00 per cent scrap to the regular burden, the charge hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap charge. The furnace employed had a hearth 16 ft. 0 in., bosh 22 ft. 0 in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter ¾ in., bosh angle 73° 27' and a Baker-Neuman top, with gas-engine blowers. Analyses Range of Material Charged Gravel: Si02, 64.40 to .7o.54 per cent; A1203,3-52 to 4.58; CaO, 7.27 to 9.49; M90, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83.

Jan 1, 1941

By C. L. T. Edwards

In the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on Ioo per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blastfurnace charge as good iron as that made without scrap—made with straight ore?" This question may he answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on Ioo per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. Operation with ioo PeR Cent Steel Scrap During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a Ioo per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when Ioo per cent steel turnings were charged. Except for occasional charges of nickel scale as an "cxtra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore—ore and scrap—operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from Ioo per cent scrap to the regular burden, the charge I hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap ' charge. The furnace employed had a hearth 16 ft. o in., bosh 22 ft. o in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter in., bosh angle 73' 27' and a Balrer-Neuman top, with gas-engine blowers. Analyses Range of material charged Gravel: SiO2, 64.40 to 70.54 per cent; A1203, 3.52 to 4.58; CaO, 7.27 to 9.49; MgO, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83. I

Jan 1, 1942

By E. S. Lenker, H. J. Van Hook

A complete swies of solid solutions has been found between the compounds InAs and GaAs Below the solidus. The melting relations determined by differential thermal and static quenching technzques, indicate that the liquidus and solidus are of the simple ascendant type. No evidence of unmixing of the homogeneous solid solutions was observed at sub-solidus temperatures. A quenching method for locnting the solidus, using X-ray diffraction techniques, is described in some detail. THE semi-conducting properties of compounds formed by various combinations of the less familiar intermetallic elements have created an increasing interest in the phase relations in systems involving these elements. The complete phase diagram of such a system, containing a compound of special interest, will often provide information as to the most favorable conditions for preparing large crystals from a melt, as well as specifying the temperature stability of the crystalline phase or phases produced. In view of the current importance of gallium arsenide in semiconductor research and of the structural similarities of indium arsenide, it was thought that the complete phase relations of the system InAs-GaAs should be investigated. Previous work on the system Ga-As by Koster and homa' and on In-As by Liu and peretti2 has shown that GaAs and InAs are the only compounds formed, having melting points of 1238° and 942°C, respectively. In a survey of various systems of elements from groups IIIb and Vb, spengler3 also re- Mines Ltd., for his continuing encouragement and for permission to publish the results of this work. ports complete miscibility of gallium, indium, and arsenic in the liquid state. In a partial investigation of the InAs-GaAs system, Woolley and smith4 found extensive solid solution throughout the alloy range. Their subsolidus work, however, was inconclusive at temperatures below 900" and they did not determine the liquidus relationships of the system. PRESENT INVESTIGATION The starting materials used were high-purity gallium, indium, and arsenic. The method of preparation of the compounds follows that devised by M. Shafer and is described in detail in a paper by Shafer and eiser.' The end-member compounds, GaAs and InAs, were first prepared by reaction of the elements in the desired proportions in evacuated silica glass vials. The vials were rotated in a furnace as the temperature was slowly raised to insure rapid and complete reaction at low temperatures. Thereafter the starting materials, GaAs and InAs, were melted by heating the sealed vials to 1300" and 1000°C, respectively; the vials in this case were filled as completely as possible to keep the vapor space small and thereby minimize the loss of arsenic to the vapor phase. Ten binary mixtures of these compounds were then prepared by reaction of the powdered material in the solid state just below solidus temperatures. At 900C preparations containing 3, 5, 8, 10, 25, 35, 50, and 75 mol pct GaAs were found to be single homogeneous phases, indicating a complete series of solid solutions between GaAs and InAs. Moreover, it was discovered that the homogeneity of any crystalline binary preparation could be very accurately checked by X-ray diffraction because of the large differences in unit cell dimensions of the end membe5s. The cubic lattice constant ofor GaAs is a = 5.652A and that of InAs is a = 6.061A

Jan 1, 1963

By R. V. Higgins, A. J. Leighton

A fast method is needed for calculating thoroughly the performance of two-phase flobr~ in reservoir rock with complex geotrietry. The authors present such a method and .slzow its accuracy by romparison with laboratory performrrnce of a five-spot pattern. In making the performance c.alculations, the octant of the five-spot pattern was divided into four channels. The computer tinle required for the culculation was one rllinrcte. This is rorighly about minute per channel. INTRODUCTION By using an electronic computer it is now possible to make reservoir performance calculations in which fewer assumptions and more significant variables are included than was possible with a desk calculator. These performance calculations include such variables as the properties of the reservoir rock and its contained fluids, properties of the rock-fluid system and even different well-spacing patterns. Usually, the more variables that are included the higher the computer cost—and time on the computer is expensive. As a result, a short procedure is needed so the many variables will be included and accurate performance calculations will result. If a reservoir is composed of alternate layers of permeable and impervioi~s rock, and if each conducting layer has a different relative permeability, the combined computer cost for calculating each layer by the present long computer programs (which includes different well-spacing patterns and other variables) would be expensive. The performances of complex spacing patterns in a field often are studied by a potentiometric model, but in these model studies the analogy is to the flow of only a single phase. This paper presents a procedure to calculate the performance of a five-spot pattern with two phases flowing using a potentiometric model as a guide for the dimensions of channels and other related data. The time required to calculate the complete performance is about one minute on the IBM 7090 or four minutes on the IBM 704. The procedure can be extended to calculate the performance of more complex well spacings or an entire field with little modification. The procedure has been tested on the performance of the laboratory water floods of a five-spot pattern reported by Douglas, et alThe range of viscosity ratios in the laboratory experiments is from 0.083 to 754, which is extensive. The accuracy of the performance calculations is excellent as shown by the plotted points in Fig. I. The recovery as influenced by the geometry of the five-spot, taking into account the deviation from true radial character, has been predicted by Aronofsky and Ramey." The authors used a potentiometric model to determine the sweep efficiency to breakthrough of the flooding agent. Dyes, Caudle and Erickson,' by means of a laboratory model, show the influence of mobility ratio on recovery after breakthrough of the injected material. Dyes, et ai, used the X-ray shadowgraph technique and miscible phases in their studies. Craig, Geffen and Morse from the analysis of the performance of their laboratory model correlate many variables, including average saturation of a flooding agent determined by permeability relationship. Craig, et al, used X-ray shadowgraphs to determine the sweep efficiencies in sandstone models. In this report the sweep efficiency is not needed, and the important effect of continuously changing saturation gradients before and after breakthrough

THE activity of the principal oil fields of Rumania followed the same course as in 1939. It was marked by (1) collaboration between the various companies, particularly in exploiting oil at great depths with a view to rationalizing the exploitation and decreasing the difficulties inherent in very deep drilling; and (2) economy in the exploitation of the older pools in reducing to a minimum the cost of the extraction and working over of wells by the concentration of productive wells in groups. The pooling arrangement continued at Tintea as a measure of conservation, and exploitation of the unitized region went forward on the basis of the norms established in 1939. The same methods were applied in the fields of Liesti, Ceptura and Boldesti. The petroleum industry had some difficulty in providing the necessary material and the hands for work. Importation of material and machines from the United States was virtually stopped. Substitutes were provided from Germany but particularly useful were certain dispositions made by the local metallurgical industry. Despite the higher cost of the production of local material and machines, they were superior to the German product, the difference in quality justifying the higher price charged as the materials were found to be particularly adapted for the purposes of the petroleum industry. The cost of production was still further raised by the work that was imposed for national defense. The rise in costs per meter drilled was 50 per cent over those of 1939. According to bimonthly tables furnished by the Moniteur du Petrole Roumain, the deepest well completed in 1940 was an exploratory well, No. 201 of the Concordia company, drilled at Tintea and suspended at 3338 meters. This depth was reached toward the close of 1939 and the well was not deepened in 1940 became of large deviation from the vertical. The record for productive wells had been held by No. 429 at Tintea, drilled by Unirea to a depth of 3200 m., and in 1938 well No. 317 Cocorasti-Mislea, of the Colombia company, but these records were passed in 1940 by well No. 613 Liliesti of the Con-cordia company, which reached a depth of 3294 m. and had an initial production of 10 tons per day. In 1940, the same number of wells, II, had been drilled to a depth of over 3000 m. as in 1939. Five of these wells are at Tintea and six at Liliesti. Table I lists these very deep holes in the order of their depth. Table i.—Deep Wells Drilled in Rumania in 1940 Initial No. Produc- of Company Field Meters tion, Well Meters Tons per Day 405 Colombia......... Liliesti 3,001 10 629 Unireu............ Tintea 3,005 73 426 Unirea............ Tintea 3,050 48 410 Colombia. ........ Liljesti 3,055 30 627 Concordja (Unirea). Liliesti 3,072 75 430 627ConcordjaConcordia (Unirea). (Unjrea 3,II9 30 618 Colombia......... Liliesti 3,168 70 24 Steaua Romana. . . Tintea 3,184 18 412 24Unirea............ Tintea 3,211 23 613 Concordia......... Liliesti 3,294 10 Production in Rumania in 1940 reached 5,813,000 tons, in contrast to 6,~40,0oo tons in 1939, a decline of 427,000 tons, or 6.8 per cent. Drilling reached 241,500 m., in

Jan 1, 1941

By J. E. Gruzleski, O. Knacke, M. J. Meixner

The evolution of CO from small specimens of solidifying steel was investigated using a thermobalance technique. Gas evolution begins in the temperature range between 1400" to .1450°C. This behavior is independent of the initial carbon content and the cooling rate. At a constant temperature above 1220°C, the rate of gas evolution is temperature independent. Out-gassing of the specimen is thought to proceed through small channels formed by the coalescence of bubbles between dendrites. LIQUID metals have a higher solubility for gas than the solid. During freezing, these gases form bubbles which may either escape or remain trapped in the solid. Recent work1 on the evolution of oxygen from solidifying silver showed that the gas is not liberated until a large fraction of the melt has solidified, and that the gas is evolved in an almost explosive manner. Because of the commercial importance of CO evolution in solidifying steel, a similar investigation was undertaken to study the mechanism of gas liberation in steel. EXPERIMENTAL The thermogravimetric method of Knacke and eixner1 to follow gas evolution by weight changes was employed. Weight differences of 0.1 mg could be reproducibly measured on specimens weighing 2.5 g. These specimens were taken from alloys with varying carbon contents from <0.01 to 0.11 wt pct and <0.01 wt pct of each of silicon, manganese, and aluminum. Specimens contained in 8 mm ID magnesium alumi-nate crucibles were heated to 1550°C under 1 atm of very pure (99.995 pct) CO with a tungsten resistance furnace. The specimen temperature was measured with a Pt-Pt/Rh thermocouple located directly beside the crucible. It is felt that the temperature thus measured was within 5" to 10°C of the specimen temperature since on fusion the weight of the specimen increased due to uptake of CO, and this weight increase was always observed to begin within the temperature range of 1530" to 1540°C. Even after 3 hr there was a small weight increase with time indicating that the molten specimen was not completely saturated with CO. Therefore, complete saturation was not attempted, and all specimens were simply held for 3 hr at 1550°C before cooling. Two types of cooling experiments were performed. One consisted of continuous cooling at linear rates from 5°C to 20°C per min down to 1020°C. The second type of experiment involved continuous cooling at 10°C per min to a predetermined temperature, and then holding the specimen at this temperature for a certain time. During all of these experiments, the sample weight was recorded as a function of time and temperature. OBSERVATIONS Continuous Cooling Experiments. No gas evolution was detected above 1450°C. The initial weight decrease always occurred between 1400" and 1450°C with the average at 1430°C. With further cooling, gas evolution continued to about 1150°C. Between this temperature and 1020°C no further outgassing was observed. This behavior did not seem to depend on the initial carbon content nor on the cooling rate in the range investigated. Typical patterns of gas evolution are shown in Figs. 1 and 2 for different initial carbon levels and cooling rates. The total amount of gas liberated during solidification varied with the rate of cooling. The total weight change on continuous cooling at a rate of 10°C per min

Jan 1, 1970

By L. D. Lamont, W. C. Muehlhof

Throughout the anthracite industry&apos;s history, the problem of handling and disposing of refuse material has been one of major importance. In the early days of the industry&apos;s activities, only the large sizes of anthracite were satisfactory for market requirements and the smaller sizes were deposited as refuse. As time went by, more efficient coal-burning equipment was developed and a market demand was created for the finer sizes of coal. This demand made it possible to recover marketable coal from banks deposited as refuse in the earlier days of mining. The same condition holds good today and we can see a definite trend toward the objective of utilizing the No. 4 and No. 5 buckwheat sizes. Under present conditions, we know that a limited market exists for No. 4 and 5 buckwheat; we know that the finer sizes of anthracite can be burned as pulverized fuel; we know that these fine sizes can be processed and sold as briquettes, and we also know that the heat content of these fine sizes of coal is comparable with that of the sizes now merchandized. Therefore, it should be the objective of the industry to conserve these fine sizes of coal in such manner that if and when processing facilities are developed, and market demands exist, the material can be salvaged and made available to meet these demands. From the standpoint of economical future reclamation, the ideal method of disposing of refuse containing the finer sizes of coal is to deposit it in banks separate and apart from other breaker refuse. By this procedure, the minimum amount of material will be processed in future salvage operations to recover the No. 4 and No. 5 buckwheat sizes. Many collieries in the anthracite region are operated under leases that have a specific term. These lease agreements provide that, upon expiration of the lease by term, exhaustion or otherwise, the ownership of the refuse material reverts to the lessor. Therefore, a question was raised in the minds of these operators: Why should I assume the expense of such procedure when I have no assurance that I will benefit by the future processing and sale of these fine sizes? Under present conditions, the answer to this question is not one of choice but of necessity, as restrictions imposed by legislation make it mandatory on operators of preparation plants to take necessary steps to properly treat silt-laden waters before permitting them to enter the streams. By reason of these restrictions, the disposal of fine sizes becomes a secondary rather than a primary operating consideration, and the procedure for disposing of this refuse becomes a matter of choice governed principally by topographical and geographical conditions. Methods of Handling Refuse There are three principal methods of handling and disposing of fine-size refuse; namely:

Jan 1, 1947

By Henry J. Welge

Laboortory apparatus has been devised which permits study of the displacement of oil from cores by water and by gas. The cores used contained interstitial brine as well as oil. Experiments were run to determine the comparative effect of varying the properties of the fluids used. No great effect was noted on the maximum displacement achieved. This observation made it unnecessary in initial work to use fluids in their exact reservoir conditions. Consequently, the displacements were run at near-atmospheric pressure in Pyrex glass equipment, using stripped crude oils. Introduction and Theory The chief object of this work has been to determine the efficiency of gas and water as primary agents for displacing oil from reservoir rock under laboratory conditions in which capillary phenomena were predominant. To this end the maximum displacement of oil from cores has been ascertained. This maximum displacement may not be equal to the maximum displacement from a reservoir; but it will be a close approxirnation to it sometimes, and other times the laboratory information will be useful in reservoir engineering predictions. It is] believed that the laboratory experimental maximum represents the upper limit for the reservoir recovery. The experiments were carried out by obtaining cores of interest from the reservoir, and filling the pores with interstitial brine and oil with the restored state tech- nique.1 Then the oil was displaced from the core as described later, either by brine from below, or by gas from above. The former type of displacement suggests analogy to production by water drive, but not to water flooding, for reasons discussed below. The latter type of displacement is believed to simulate production by gas cap displacement. The displacements were performed by what may be termed the capillary-pressure method. The cores are placed in capillary contact with an oil-wetted membrane which has very small pores (about I micron in diameter). Pores of this size will transmit oil but Prevent the Passage of gas or water, unless the Pressures used are higher than the capillary Pressures employed in this work. Accordingly, use of the membrane makes it possible to apply a capillary pressure differential between the displacing phase and the oil in the core. AS in the displacement of brine toward that condition of oil and water distribution existing originally in the reservoir,&apos; it may not always be desirable to reduce the oil saturation in this experiment to an absolute minimum. With reservoirs having small productive closure, it is preferable to evaluate and use a displacing pressure no higher than the capillary pressure, Ap, which will ultimately become available for displacement in the reservoir. This pressure may be calculated from a knowledge of the density of the oil-in-place, do, the density of the displacing phase, dl, and Ah, the vertical distance between the section of the

Jan 1, 1949

By W. C. Muehlhof, L. D. Lamont

Throughout the anthracite industry&apos;s history, the problem of handling and disposing of refuse material has been one of major importance. In the early days of the industry&apos;s activities, only the large sizes of anthracite were satisfactory for market requirements and the smaller sizes were deposited as refuse. As time went by, more efficient coal-burning equipment was developed and a market demand was created for the finer sizes of coal. This demand made it possible to recover marketable coal from banks deposited as refuse in the earlier days of mining. The same condition holds good today and we can see a definite trend toward the objective of utilizing the No. 4 and No. 5 buckwheat sizes. Under present conditions, we know that a limited market exists for No. 4 and 5 buckwheat; we know that the finer sizes of anthracite can be burned as pulverized fuel; we know that these fine sizes can be processed and sold as briquettes, and we also know that the heat content of these fine sizes of coal is comparable with that of the sizes now merchandized. Therefore, it should be the objective of the industry to conserve these fine sizes of coal in such manner that if and when processing facilities are developed, and market demands exist, the material can be salvaged and made available to meet these demands. From the standpoint of economical future reclamation, the ideal method of disposing of refuse containing the finer sizes of coal is to deposit it in banks separate and apart from other breaker refuse. By this procedure, the minimum amount of material will be processed in future salvage operations to recover the No. 4 and No. 5 buckwheat sizes. Many collieries in the anthracite region are operated under leases that have a specific term. These lease agreements provide that, upon expiration of the lease by term, exhaustion or otherwise, the ownership of the refuse material reverts to the lessor. Therefore, a question was raised in the minds of these operators: Why should I assume the expense of such procedure when I have no assurance that I will benefit by the future processing and sale of these fine sizes? Under present conditions, the answer to this question is not one of choice but of necessity, as restrictions imposed by legislation make it mandatory on operators of preparation plants to take necessary steps to properly treat silt-laden waters before permitting them to enter the streams. By reason of these restrictions, the disposal of fine sizes becomes a secondary rather than a primary operating consideration, and the procedure for disposing of this refuse becomes a matter of choice governed principally by topographical and geographical conditions. Methods of Handling Refuse There are three principal methods of handling and disposing of fine-size refuse; namely:

Jan 1, 1947

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920&apos;s to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu&apos;s in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920&apos;s were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953