Search Documents

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,' continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,' which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

By D. J. Jr. McAdam

This paper presents stress-cycle graphs for five samples of monel metal and three high-strength aluminum alloys. These graphs are evidently curves with horizontal asymptote. The position of the horizontal asymptote can be determined with sufficient accuracy by extending the experiments to not more than 50,000,000 cycles. For some of the graphs, there is a slight downward slope between 50,000,000 and 100,000,000 cycles. The slope is so slight, however, that, extrapolation from 50,000,000 to 100,000,000 cycles gives the endurance limit with sufficient accuracy. Monel metal and duralumin are not exceptional among non-ferrous metals in endurance properties. IN Part I of this paper' a comparison was given of the results obtained in investigation of the endurance properties of non-ferrous metals in .three laboratories: the Engineering Experiment Station of the University of Illinois, the U. S. Air Service at McCook Field, Dayton, Ohio, and the U. S. Naval Engineering Experiment Station, Annapolis, Md. Part I was devoted to a discussion of the forms of the stress-cycle graphs obtained at the three laboratories. For comparison, typical graphs obtained at the three laboratories were plotted on the same semi-logarithmic scale. The typical rotating-cantilever graph for ferrous and non-ferrous metals obtained at the Naval Experiment Station was described as a curve descending with gradually decreasing slope to a horizontal line. In the reply to the discussion of Part I, however, this graph was described as a curve with horizontal asymptote. It. was also said that the ordinate of the asymptote (the endurance limit) could be determined by endurance tests of not more than 50,000,000 cycles. This description was intended to apply only within the range of ordinates used in plotting an ordinary endurance graph. It was recognized that if .extended upward beyond the usual field, the curvature of the graph would decrease until -the graph would either approach a straight a line or possibly reverse its curvature.

Jan 2, 1926

By A. B. Kinzel

SINCE the exposition of the behavior of certain iron alloys by Sykes1 involving the existence of an austenite loop and the discovery of such a loop in the chrome iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena is presented here. MATERIAL The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic Eton and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in, in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged to wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.

Jan 1, 1928

By Paul B. Crawford, Bobby L. Landrum

An electrical model study has been mode to estimate the effect of horizontal fractures in thick reservoirs on pattern conductivity. For the patterns studied, it is shown that fracturing all the wells in the pattern in-creases the conductivity considerably more than frac-turing only single wells. For certain conditions one large fracture is more effective in increasing conductivity than several fractures of half the radius. Particularly in thick reservoirs and with large fractures, the center of the pay is found to be more responsive than other locations. For the seven-spot pattern fracturing the center well is more effective in increasing pattern con-ductivity than fracturing all outer wells with fractures of the same size. INTRODUCTION Although commercial fracturing has been used for some time very little quantitative information is known about the effects of fractures on reservoir behavior. The purpose of this work was to estimate the effect of horizontal fractures in thick reservoirs on the con-ductivity of various flooding and cycling patterns.2 Circular fractures originating at the wellbore and extending symmetrically into the pay were considered. ANALYSIS Electrical models were used in making this study. Horizontal fractures were simulated by copper sheets shaped like the fractures and of a proportional size; the wellbore was simulated by a copper wire. A dilute salt solution served as a conducting medium. A con-ductivity bridge was used to measure the conductivities of the various patterns studied. EFFECT OF HORIZONTAL FRACTURES ON CONDUCTIVITY Fig. 1 shows the effect on square and staggered line drive patterns of horizontal fractures located in the center of the pay. The model is shown schematically in the insert. The upper and lower groups of lines show the effect on conductivity when all wells are fractured, and when only one well is fractured, respectively. In general, pattern conductivities are substantially improved by fracturing all wells. Fig. 2 shows the effect of multiple horizontal frac-tures on the conductivity of a line-drive pattern. At

Jan 1, 1958

By W. H. Porter, M. E. Wadsworth, J. R. Lewis, K. L. Leiter

The oxidation of Cu2S in oxygen and the sulfating of Cu2O in oxygen-sulfur dioxide atmospheres was carried out under a variety of conditions. The oxidation of Cu2S was found to be retarded by entrapment of SO, and O2, which stabilized internal sulfates for long periods of time. The course of the reaction was followed by measuring weight changes and also by SO, evolution. Sulfating of Cu2O was a maximum at ratios of SO, to O2 approximating maximum SO, production. At elevated temperatures SO, was found to increase the rate of oxidation of Cu2 O to CuO even though sulfates did not form. All sulfating reactions followed the parabolic rate law indicating diffusion. MANY studies of the roasting of copper sulfides have been reported in recent years. Diev et al.1 investigated the roasting of chalcocite (Cu2S) in air, and oxygen enriched air. Lewis et al.2 also studied the oxidation of natural and synthetic chalcocite in air and oxygen atmospheres and their studies indicated that the maximum formation of water soluble sulfates occurred at approximately 450oC. Ashcroft3 reported that oxide production during the roasting of chalcocite resulted only from secondary decomposition of sulfates which were formed as primary products. peretti4 refuted this claim by showing that a layer of Cu2O appeared directly adjacent to the Cu2S during roasting of cylindrical briquettes of cupric sulfide, CuS. The linear advance of the Cu2S-Cu2O interface was used as a measure of the kinetics of the roasting reaction. The reactions proposed were: 2 CuS—Cu2S + 1/2 S2 [4-1] 1/2 S2 + O24 SO2 [4-2] cuzs +3/2 O2 4 Cu2O + SO2 [4-3] cu2o + 1/2 O2—2 cuo [4-4] At temperatures above 663oC, CuO was the only final solid phase reported. Below 663" C increasing amounts of sulfate were found mixed with the CuO. McCabe and Morgan5 investigated the roasting of discs of synthetic chalcocite and reported the following sequence of products beginning at the sulfide surface: Cu2O, a mixture of Cu2O and CuSO4, Cum,, CuO . CuSO4, and CuO. The principal reactions were reported to be: Cu2S + 3/2 O2-Cu2O + SO2 [5-1] CU2O + 2 SO2 + 3/2 O2—2 CUSO4 [5-21 2 CUSO4— CUO . cum, + SO3 [ 5-31 cuo . cuso4—-2 cuo + SO, [ 5-41 Eq.15-11 supports the claim of Peretti, Eq. [4-31, that CuzO is formed directly from Cu2S rather than as a secondary product from a sulfate as suggested by Ashcroft. On the other hand CuO was found to form as a secondary product from the decomposition of copper sulfate and basic copper sulfate, Eqs. [5-31 and [5-41. The formation of sulfates was explained by McCabe and morgan5 to be a direct reaction of Cu2O with 0, and SO, or SO, at distinct regions in which the partial pressures of each were such as to form the sulfate. Thornhill and pidgeon6 roasted both natural and synthetic chalcocite grains in air at temperatures between 420" and 550° C. They found a dense primary oxidation layer in contact with the sulfide. A secondary layer of porous oxidation products was found to expand with roasting time. The oxide products were leached away and the remaining core was studied by X-ray diffraction. The X-ray patterns showed an increased conversion of chalcocite to digenite with time. Digenite,7 a defect structure of cuprous sulfide, occurs naturally as Cu,-,S where x = 0.12 to 0.45, with an average analysis of Cu, ,S. The mechanism of digenite formation was proposed as: Cu2S + oxygen—Cu1-8S + 0.1 Cu2O [6-1] Cuj.eS + oxygen—0.9 Cu2S + SO2 [6-2] It is apparent from the above studies that the oxidation of Cu2S, ultimately ending in CuO, may be divided into ihree general stages (all of which may occur simultaneously): 1) primary oxidation to Cu2O; 2) secondary sulfate formation; and 3) sulfate decomposition. Consequently reactions of O2 and SO, with Cu20 constitute important aspects of the roasting of chalcocite. Virtually no studies have been made regarding sulfating reactions involving Cu,O. Mills and Evans8 noted the effect of sulfur dioxide on the oxidation of copper at low temperatures and low SO, partial pressures. They reported a measurable increase in the oxidation rate of copper when SO2, was present. Interest in the Cu2O-CuO-0, system has been limited predominantly to misciblllty studies and determinations of heats of formation by

Jan 1, 1961

By C. E. Shoenfelt

There were 110 important discoveries of either oil or gas in Co1orado in 1935. There was, however, further development of the Price structure in southern Colorado and developments since the first of the year indicate. that an important oil field may be in the making. The discovery of oil in Price structure was made by the Oil City Petroleum Co. late ill Novem-ber, 1934, in its No. 2 Garnett in the northeast corner of lot 3 in the SW.¼ of sec. 25-33N.-2E. This well developed a good showing of oil in Dakota sand at 970 ft. The hole filled up 15 ft. with 40° gravity oil overnight and after standing for several days the oil level was 400 ft. higher. As a result of the discovery of oil by the No. 2 Garnett, three wells were drilled by the William E. Hughes Estate. Two of these wells had good showings of oil and may make good producers but it is doubtful whether they will produce the estimated capacity of 500 bbl. each with which they have been credited. Although the Hughes Estate wells have been completed for some time, they have not been given thorough production tests because of the isolated position of the field and lack of proper facilities. The. first well drilled by the Hughes Estate was located on the west side of the Navajo River on the downthrow side of a fault. It encoun-tered water ill the Dakota sand at 1285 ft, and was abandoned in green shales of the Morrison at 1405 ft. Well cuttings from the Dakota sand showed some evidence of once containing oil, so a 1ocation was selected for No. 2 Fee on the east side of the river and on the upthrow side of the fault. Oil was discovered in Dakota sands ill 1935 by Continental Oil Co. in its No. 3 Hoye, NW.NW.NE. of sec. 34-9N.-78W., on the South McCallum anticline in North Park, Jackson County, Colo., but on account of heavy flows of carbon dioxide gas under high pressure it has been impossible for the company to get an accurate gage of the oil production. The freezing action of expanding carbon dioxide makes the producing of the oil difficult and costly.

Jan 1, 1936

He took a great interest in technical matters and his inclination was strongly toward research investigations. At the same time he was effective in manual and mechanical work and was generally found working side by side with the men under his direction. His nature was unselfish and he was extremely popular socially. He was a member of the Coeur d'Alene Commandery, Knights Templar. Stanly A. Easton. Lieutenant.Louis Baird Louis Baird, a Lieutenant in the Royal Field Artillery of the British Army, died on the battlefield in 1915. Lieutenant Baird was born July 28, 1880, at Stirling, Scotland. His technical education was obtained at King's College, Melbourne, Australia, in 1893 to 1895, and at the Technical College at Glasgow, Scotland, in 1897 to 1900. After an apprenticeship with the Mexican J. & 8. Rec. Co. of Mexico, lasting from 1900 to 1903, he became mill superintendent for the Cia. Minera Benito, at Juarez, Zac. During the year 1905-6 he was assistant manager of the Candelaria y Anexas, at Pinos, Zac., and from 1906 to 1907 was engineer with the Cia. Minera Jalisco, San Sebastian, Jalisco. At the time of his admission to the Institute, in 1908, he was practising as a mining engineer at Etzatlan, Jalisco, Mexico. For the next four years he practised his profession in the City of Guadalajara, Jalisco, removing, in 1913, to Ixtlan del Rio, in the State of Tepic. It was from here that he returned to England to put his services at the disposal of the British Government. The Institute is not definitely informed as to how, where, or when Lieutenant Baird met his death. Captain John H. Ballamy John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on Aug. 9, 1918. Captain Ballamy was born at Plvmouth. Pa.. in 1886 and graduated from' the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Rai1roa.d Company's coal mining

Jan 1, 1920

By C. E. Shoenfelt

There were 110 important discoveries of either oil or gas in Co1orado in 1935. There was, however, further development of the Price structure in southern Colorado and developments since the first of the year indicate. that an important oil field may be in the making. The discovery of oil in Price structure was made by the Oil City Petroleum Co. late ill Novem-ber, 1934, in its No. 2 Garnett in the northeast corner of lot 3 in the SW.¼ of sec. 25-33N.-2E. This well developed a good showing of oil in Dakota sand at 970 ft. The hole filled up 15 ft. with 40° gravity oil overnight and after standing for several days the oil level was 400 ft. higher. As a result of the discovery of oil by the No. 2 Garnett, three wells were drilled by the William E. Hughes Estate. Two of these wells had good showings of oil and may make good producers but it is doubtful whether they will produce the estimated capacity of 500 bbl. each with which they have been credited. Although the Hughes Estate wells have been completed for some time, they have not been given thorough production tests because of the isolated position of the field and lack of proper facilities. The. first well drilled by the Hughes Estate was located on the west side of the Navajo River on the downthrow side of a fault. It encoun-tered water ill the Dakota sand at 1285 ft, and was abandoned in green shales of the Morrison at 1405 ft. Well cuttings from the Dakota sand showed some evidence of once containing oil, so a 1ocation was selected for No. 2 Fee on the east side of the river and on the upthrow side of the fault. Oil was discovered in Dakota sands ill 1935 by Continental Oil Co. in its No. 3 Hoye, NW.NW.NE. of sec. 34-9N.-78W., on the South McCallum anticline in North Park, Jackson County, Colo., but on account of heavy flows of carbon dioxide gas under high pressure it has been impossible for the company to get an accurate gage of the oil production. The freezing action of expanding carbon dioxide makes the producing of the oil difficult and costly.

Jan 1, 1936

By W. A. Boyer

Edward Thomas (U.S. Bureau of Mines, Washington, D. C.)—This excellent article on an ingenious and successful installation of wooden rock bolts loses much of its effectiveness through an attempt by the authors to establish the general adaptability of this type of support. Possibly because they have only local experience as a guide, they imply erroneously in the first paragraph that the Bureau of Mines has been opposed to wooden bolting, although later in the article reference is made to a Bureau publication on the subject. In 1947 the Bureau of Mines decided to sponsor experiments in roof bolting in coal mines because the experience of the St. Joseph Lead Co. had indicated that this type of roof support appeared to be a roof-fall accident-prevention measure that might be adopted and also effect economies in operating cost. Justification for this belief has been borne out, particularly in coal mining. This program has been carried out under the following general program: 1—The Roof Control Section of the Bureau of Mines has advocated and initiated underground experiments under controlled conditions with many different ideas related to rock bolting since 1947. In no instance has cooperation in developing an idea been refused, no matter how ridiculous it may have seemed at first glance, if it has been requested by a mining company. 2—The Bureau of Mines has no police powers over the selection of roof-support devices and seeks none. 3—At the request of an operator, the Bureau of Mines will make comparative tests on various types of bolts underground and will submit resultant data for the operator's consideration. 4—Wherever possible, the Bureau publicizes successful installations, so that others may benefit from this experience; however, it is careful not to discriminate between manufacturers of bolts or bolt-installation equipment. Unsuccessful experiments probably should also be publicized, but from a practical standpoint it is usually not feasible. In other words, the role of the Roof Control Section of the Bureau is in line with the original purpose for which the Bureau was first organized: to serve industry through gathering, analyzing, and disseminating factual data. It would seem to be logical that the starting point for any experimentation on roof bolts in coal mines should be the time-proved practice of the

Jan 1, 1955

By Tracy C. Jarrett

The alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,' E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various elements upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency inductiorl furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5" F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by 45 by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by % by % in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second scries consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1940

By Tracy Jarrett

THE alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,1 E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various ele¬ments upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency induction furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5° F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by ½ by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by ¼ by ¾ in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second series consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1939

By Tracy C. Jarrett

The alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,' E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various elements upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency inductiorl furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5" F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by 45 by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by % by % in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second scries consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1940

By Roy Hardy

THE Getchell mine is a comparatively recent discovery in the old Potosi mining district, Humboldt County, Nevada, a district organized in the seventies and eighties, in which some prospecting was done in several metamorphic zones along a monzonite-sedimentary contact. The district had no production in the early days and no further work was done until the same metamorphic zones were prospected for tungsten (scheelite) in 1917 and 1918, when a few small lots were shipped. It again lay dormant until 1934, when prospectors investigated a large siliceous escarpment at one end of the old district where outcroppings were a prominent feature of the topography. Undoubtedly, during the early prospecting of the district, the outcroppings had been investigated for mineral, probably by panning, with negligible results because the gold later found is invisible in the concentrate and is refractory. A fire assay revealed the presence of sufficient gold to warrant develop-ment work. The outcroppings were easily prospected by short tunnels having their portals in the siliceous material on the hanging-wall side, with a maximum distance to crosscut to the footwall of 135 ft., or a distance at right angle to dip of 60 to 90 ft. Development work, reaching a depth of over 600 ft. on the dip of the vein, was done by means of various crosscut tunnels, winzes and laterals. A churn-drill hole was also sunk, which intersected the vein at a depth of 1100 ft. on the dip. Sufficient development work of this character was completed by 1937 to justify the erection of a reduc-tion plant to roast the sulphide ore and cyanide the calcine, and to treat the oxidized ore by straight cyanidation, to make a doré bullion for shipment to the mint. The erection of the plant was started that year and finished early in 1938, with a combined capacity of about 800 tons per day. It has operated continuously since erection and recently was enlarged to handle 1000 tons per day. The vein dips with the slope of the mountain, and by stripping the hanging wall the ore may be mined by power shovel for several hun-dred feet below the outcrop. Thereafter underground methods will be necessary.

Jan 1, 1940

By R. G. Davies

Isothermal annealing of quenched Fe3Al reveals that the superlattice forms by the nucleation and growth of ordered domains. The activation energy for isothermal ordering and initial domain growth is -29 keal per mole, which is thought to he the activation energy for vacancy migration. Domain growth, in the absence of excess vacancies, has an activation energy of -100 keal per mole. A maximum in the hardness is observed when the structure consists Of ordered domains, -35-4 in size, growing into a short-range ordered matrix and, also as a function of degree of order, S, with an infinite domain size at S = 0.4 to 0.5. It is proposed that both maxima are due to a transition from deformation by unit dislocations to deformation by superdislocntions. FE-AL alloys containing more than -23 at. pet Al, when quenched from above the critical temperature for the Fe3A1 type of order, always contain the maximum possible amount of FeAl (B2) type of order' (see Fig. 1). Thus when the Fe3A1 superlattice forms, in a 25 at, pet A1 alloy, it does so from an imperfect FeAl structure. The formation of the Fe3Al superlattice has been the subject of several recent X-ray,1, 2 electrical-resistivity,3"6 and dilatometric3 investigations. McQueen and Kuczynski3 concluded that the isotherma1 ordering of Fe3Al, after quenching from 800°C (T,, the critical temperature for order, is 55O°C), takes place by the nucleation and growth of ordered domains. However, Feder and Cahn4 found that the isothermal ordering was complex but more like a homogeneous nucleation process than a nucleation and growth process. Lawley and Cahn2 reported that the degree of order is a continuous function of temperature which is a characteristic of a homogeneous nucleation process. Thus, the evidence is conflicting as to the nature of the Fe3Al ordering reaction. Lipson7 was the first to suggest that ordered domains should exist in the Fe3A1 structure since, as

Jan 1, 1964

By Eldon N. Dunlap

Recently the producing branch of the petroleum industry has shown a considerable and growing interest in the quantitative determination of the water, oil, and gas content of cores as it relates to estimation of reserves, to providing a basis for judging as to the feasibility of applying various secondary-recovery and pressure-maintenance processes, and in general to the operation of producing properties. For years it has been known that oil, gas and water coexisted in the pores of many semidepleted oil measures. It is now generally believed that oil-bearing beds contain connate water in amounts varying up to 50 per cent of the pore space. However, only lately has reliable direct evidence of the extensive occurrence of connate water in oil sands been published. Very little work has been done to ascertain the effect of this water on the productivity and ultimate recovery of oil from wells. It was the intent of this research to study the influence of interstitial water on the flow of oil through unconsolidated sands, with the hope that the results could be applied qualitatively to the flow of oil in underground reservoirs partly saturated with water. Obviously, ultimate recovery estimates based on the void volume of the reservoir will be in error unless a correction is made for the volume of water that occupies a portion of the effective pore volume of the reservoir. Evaluation engineers in the past have applied arbitrary saturation and recovery factors that may inadverently have compensated for the failure to consider specifically the water content. Nevertheless, the evidence available indicates that these factors need revising if each is to be independently correct and truly representative. Although the fact that the connate water renders part of the pore volume of the reservoir incapable of containing oil is of primary importance to the operator, it is also to his interest to know to what extent the presence of varying amounts of interstitial water influences the permeability of the sand to oil.

Jan 1, 1938

By Dorsey A. Lyon, Robert M. Keeney

The electric furnace has always been found to be especially adapted to melting, refining, and finishing processes throughout its gradual acceptance by metallurgists as a practical apparatus for conducting metallurgical operations. In the steel industry, the electric furnace is firmly established in the manufacture of steel of the highest grade, equal to crucible steel. For the production of the cheaper grades of steel in large tonnage, the electric furnace gives a higher-grade product than the open-hearth or converter, but due to the high cost of power prevailing in steel centers, considered from the electric furnace standpoint, it is not economical to produce tonnage steel in the electric furnace. As a refining and finishing agent for open-hearth or Bessemer steel, the electric furnace has had some degree of success in thc production of tonnage steel. After a study of the use of the electric furnace in the steel industry, it appears that there may be a possibility of its use to advantage for the melting of cathode copper. In the case of copper the problem is not one of actual refining, because the copper if refined properly by the electrolytic method needs no further refining; it needs simply to be cast into a marketable shape. The name "refining" is applied to the present finishing process, because in the operation oxygen and other impurities arc removed, which the electrolytic copper absorbs in being melted in the reverberatory furnace. Considering that processes may be positive, negative, and neutral, the electrolytic method would be positive; reverberatory melting of cathode copper, negative; and electric furnace melting, neutral. The electrolytic method produces about as pure a copper as is possible, if operated properly and the anodes are not too impure. The final reverberatory melting of this cathode copper lowers the grade of the final product, due to the absorption of gases and impurities. The reverberatory melting of cathode copper is one of the weak parts

Jan 1, 1915

By George Rice

WITH so tremendous a subject, an attempted review of the coal situation of the world in a short talk must necessarily be of a sketchy character. It is hardly necessary to tell a body of engineers that had it not been for nature's gift of coal the material side of modern civilization would never have reached its present status. On the other side, it is regrettable that it was a byproduct of coal, T. N. T., which made possible Germany's initial success in this war, because that country had an enor-mous development of manufacturing plants that could be immediately utilized to make this destructive agent. One sometimes hears the casual remark that when the coal of the world is exhausted we shall use electricity; but, of course, electricity is ordinarily only a means of transforming and transmitting energy derived from fuel or water power, and chiefly from coal. It is true, we have much undeveloped water power, but it is more or less remote from the centers of industry; and when all shall have been developed it will not begin to supply the power requirements of the world. It is, however, reasonable to expect that before the world's supply of coal shall be exhausted, methods will have been discovered of harnessing other forces of nature, such as the tides, or the energy emanating from the sun. Petroleum and natural gas naturally come to mind, but the days of both, as fuel, appear to be numbered, although the products of petroleum, if economically used, doubtless will be available for internal-combustion engines, automobiles, trucks, and boats. for a long time, provided the reckless use of crude petroleum as an ordinary fuel is stopped. The products of petroleum are too valuable to mankind for such waste to be permitted. The civilization of the world, therefore, appears to rest, and, so far as can be seen, will indefinitely continue to rest, upon coal.

Jan 1, 1918

By John A. Garcia

A standard set of coal mining laws for the entire United States is hardly practicsble, yet the numerous variations in the state laws for almost every item seems entirely unnecessary. The same useless variations appear in almost every comparable section with no apparent reason except that no attempt has ever been made to codify them, and as they were developed over a long period of time by innumerable individuals and legislatures, the present situation is the logical outcome of lack of cooperation between states. The ventilation of a mine is affected indirectly by many provisions not listed specifically under this heading, so that it would be necessary to tabulate the major portion of all the laws to secure a complete comparable digest; therefore only a few of the more important have been set down here. This point is well illustrated in the section providing for clearance between car and rib, which is intended as a safety measure against personal injury, but is very important from the standpoint of ventilation because of choked airways in mines on two-entry system. Confusing Phraseology Misinterpretation and confusion may be expected from the phraseology alone; one state provides that the scale of the mine map shall be "not more than 100 ft. to 1 in.;'' another state demands "not less than 100 ft. to 1 in." Both probably mean the same thing and seek to prevent the operator from furnishing a map on which the workings will appear SO small that the detail is illegible. Legislation is certainly indefinite that specifies structures must be fireproof when "near" a mine opening, and just what is a "dusty" or "gaseous" mine is open to argument in most of the states. The variation in spacing crosscuts and break-throughs and the limited number of men on a split seem entirely unnecessary, as the distance is not reduced in gaseous fields, excepting in Arkansas and Tennessee, which states produce a comparatively small amount of coal, and the number of men differs 100 per cent. and more for no apparent reason.

Jan 1, 1927

By W. C. Schroeder, A. A. Berk

Practical experience has shown that at elevated temperatures solutions containing sodium hydroxide may attack stressed steel in a manner that cannot be explained in terms of ordinary corrosion. Because the ductility of the metal has been greatly reduced during the reaction, the entire phenomenon is usually called "embrittlement." Thus, after several years of operation caustic evaporators have been so badly embrittled that rivets could be cracked off with the blow of a hammer. Since fine intergranular cracks are almost always present in the zone of fracture, it has often been assumed that a process of selective corrosion in grain boundaries was responsible for the failure, although this has not been clearly proved experimentally. Concentrations of sodium hydroxide below those necessary for the uniform, rapid attack of the steel surface are reported to be most effective in producing embrittlement2, 3. In the operation of steam boilers a similar type of failure has been found, mainly in riveted seams or other capillary spaces where the solution may concentrate and where high stresses may also exist. It is believed that in such localized areas the dissolved solids may reach a value many times the few hundred parts per million prevalent in the body of the boiler. While this type of boiler failure has been the subject of investigation for a period of 20 years1, an understanding of its mechanism and a rational basis for complete protection have not yet been secured. To procure this information the present investigation was

Jan 1, 1936

By A. A. Berk, W. C. Schroeder

Practical experience has shown that at elevated temperatures solutions containing sodium hydroxide may attack stressed steel in a manner that cannot be explained in terms of ordinary corrosion. Because the ductility of the metal has been greatly reduced during the reaction, the entire phenomenon is usually called "embrittlement." Thus, after several years of operation caustic evaporators have been so badly embrittled that rivets could be cracked off with the blow of a hammer. Since fine intergranular cracks are almost always present in the zone of fracture, it has often been assumed that a process of selective corrosion in grain boundaries was responsible for the failure, although this has not been clearly proved experimentally. Concentrations of sodium hydroxide below those necessary for the uniform, rapid attack of the steel surface are reported to be most effective in producing embrittlement2, 3. In the operation of steam boilers a similar type of failure has been found, mainly in riveted seams or other capillary spaces where the solution may concentrate and where high stresses may also exist. It is believed that in such localized areas the dissolved solids may reach a value many times the few hundred parts per million prevalent in the body of the boiler. While this type of boiler failure has been the subject of investigation for a period of 20 years1, an understanding of its mechanism and a rational basis for complete protection have not yet been secured. To procure this information the present investigation was

Jan 1, 1936