Search Documents

By B. J. Harlan

THE trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and 1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years.

Jan 1, 1934

By Jed H. Mosgrove, Paul M. Budzak

INTRODUCTION Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 m3/s (9000 cfm) of air at his last open crosscut. PLANNING What will provide adequate ventilation? A rule of thumb in laying out a coal mine is to provide enough entries in the main entry system to keep air velocities at 2.5 m/s (500 fpm) or less; at this rate of flow, good ventilation may be expected. The intake and return air courses of a coal mine do not improve with age. Entries will deteriorate, ribs will slough, roof will fall, and clutter will accumulate. The resistance offered to air travel will continue to increase with each passing year. Providing enough airways for the present and the future cannot be emphasized too strongly. In order to better appreciate good planning and bring it into better focus, assume a hypothetical mine has the following features: entries 1.5 m (5 ft) high and 6.1 m (20 ft) wide; one intake and one return entry; the mine development is 4.8 km (3 miles) from the intake and upcast ventilation shafts; and the ventilation requirement is 141.6 m3/s (300,000 cfm). Air travel of 4.8 km (3 miles) into a mine and the same distance back to the fan is not unusual. However, to do so with one intake and one

Jan 1, 1981

By K. P. Wang

Under the Communist regime marked industrial progress has been achieved on the China mainland. Within a decade, the country has been transformed from an economy primarily agricultural to one bristling with industrial possibilities. The industrial capacity of Communist China is beginning to approach that of Japan and will probably surpass it by 1962, the last year of the Second Five-Year Plan. The slogan already is Beat the United Kingdom by 1972, a goal which most observers feel will be achieved ahead of schedule. During the early years of the industrialization program in Communist China, emphasis has been placed on basic goods; hence additional time will be needed to make large quantities of the more complicated products. However, regardless of the current stage of industrial development, it is apparent that the necessary forward momentum has been created. The many capital construction projects being brought into production and the additional projects being initiated confirm this observation. The accuracy of Communist China's industrial statistics can be questioned, but their order of magnitude is clear. To properly evaluate the industrial capability of the country, differentiation must be made between the absolute quantities that reflect overall strength and the per capita quantities that reflect living standards. While Communist China is well on the road to becoming a world power, its living standards will remain below European levels for many years to come.

Jan 8, 1960

By W. O. Philbrook, A. E. El-Mehairy

The reduction by hydrogen of individual particles of dense hematite implanted in beds of inert spheres is controlled by single-particle kinetics. No evidence of reagent starvation was found down to low flow rates established by pressure gradients as low as 0.01 in. H2O per- in. of depth in beds of spheres as small as 3/16 in. diam. The optimum size for most rapid reduction of beds of homogeneous ores results from the effect on reducing potential of the gas of competing factors of supply and consumption. A recent publication1 presented the results of a study of the rate of reduction of iron ore in a fixed bed by hydrogen introduced at constant pressure differential. Under these conditions the reagent flow rate varied directly with the bed permeability, which was a function of particle size and shape and bed voidage, and inversely with the temperature-dependent viscosity of the gas. The present note adds data from supplementary experiments designed to reveal whether or not any partial reagent starvation arising from a flow-dependent transport resistance in the gas phase might have been operative. Kinetic studies were made of the reduction of individual spheres of iron oxide inserted into beds of inert spheres, so that the reagent flow rate and aerodynamic conditions were again determined by bed characteristics and temperature. The experimental techniques and apparatus were similar to those previously described.' The synthetic iron ore spheres were wet-rolled by hand from powdered, reagent-grade* Fe2O3 and subsequently dried and then fired in air at 1250°C. The indurated pellets has almost no porosity as indicated by their specific gravity of 5.10. The beds were made of dense alumina spheres, closely sized to the same dimension as the iron oxide spheres, in the following diameters: 3/16, 1/4, 5/16, and 3/8 in. Each bed was hand-packed of particles of a single size to a controlled voidage of 0.32 and depth of 3 in. within a capsule having an internal diameter at least 10 times the particle diameter. A few weighed iron oxide spheres were individually planted in the central plane of the bed of inert spheres at points away from the wall. Reduction was carried out at atmospheric pressure by purified hydrogen at 670°, 800°, and 985°c. The reagent was supplied at precisely controlled pressure differentials of 0.01, 0.02, and 0.03 in. of water per in. of bed depth. This gave a range of flow rates similar to that used in the study of beds of ore and comparable with blast-furnace practice in terms of mols of reducing gas per hr per sq ft of cross-section. Viscous flow prevailed in all beds under the experimental conditions of this study. The reduced particles were checked for loss in weight and then sectioned for metallographic examination. Occasional particles were found to have contained minute internal cracks that interfered with the concentricity of the reduction interfaces, and data for such particles were rejected. An experimental rate constant for the reduction of the imbedded Fe2O3 spheres was calculated on the assumption that the rate was proportional to the metal-oxide interface area by an equation that has been found by McKewan2 to describe the reduction of single spheres

Jan 1, 1962

By L. W. Saperstein, D. Yeung, L. B. Phelps

Introduction The success of preventive methods for the mitigation of coal mine drainage formation will require a marriage of the minimization of initial coal mine drainage formation, the minimization of toxic fluid formation after toxic material disposal, the minimization of the mobilization and transpor¬tation of formed toxic fluids, and the maximization of the rate of diultion and attenuation of the formed toxic fluids. This paper contributes to the understanding of factors af¬fecting mobilization and dilution and attenuation of formed toxic fluids. When water containing a salt content different from in situ pore water in the soil is passed through a body of soil, the concentration of salts in the outflow will gradually change composition in a manner that depends on the kinds of hydraulic processes that occur in the soil. These processes are molecular diffusion, lateral dispersion, longitudinal dispersion, chemical reactions or exchange, physical adsorp¬tion, and biological retardation. This note considers only the first three processes. These three microscopic processes can be analyzed statistically on a probability basis. Such results, confirmed experimentally, indicate that a tracer introduced instantaneously as a point source will tend to form a Gaussian normal distribution as it moves downstream (Todd, 1964). Dilution During Flow The closed-form soltuion for pulse or instantaneous injec¬tion of a tracer during confined flow in a homogeneous porous medium shows that the maximum tracer concen¬tration at a point in space, x, after the time interval, t*, is given by [ ] where Aa is the effective flow cross-sectional area; A is the column cross-sectional area; a is soil porosity; M is mass of the injected tracer; C is concentration of the tracer in the permeating fluid and is a function of x and t*; D is the longitudinal dispersion coefficient; and va is the interstitial fluid velocity (Klotz and Moser, 1974). Therefore, the following conclusion can be made: • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, and a fixed mass of injected tracer, M, Cmax will decrease as the time of peak outflow concen¬tration t* increases. • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, a fixed mass of injected tracer, M, and a constant interstitial fluid velocity, va Cmax will decrease as the distance of travel, x, increases. • For a medium of constant cross sectional area, A, con¬stant soil porosity, a, a constant mass of injected tracer, M, and a fixed distance of travel, x, Cmax will decrease as D/va increases. Klotz and Moser (1974) concluded that D is about proportional to no.3 where r) is the kinematic viscosity; D is about proportional to a-3 where a is soil porosity; D in¬creases with increasing grain size; D increases as grains become less spherical; D increases with greater grain rough¬ness and angularity; D increases with increasing uniformity coefficient; and D is significantly affected by grain size and uniformity coefficient. The remaining parameters are not significant. Numerical Simulation Studies Numerical simulation studies were used to investigate the nature of flow and the optimum length of a toxic package within a saturated porous medium of fixed dimensions and configuration (Fig. 1). The width and position of the package was maintained constant (Phelps et al., 1981). Results indicate that if the package extends throughout the length of the model, the flow is vertically downward and

Jan 1, 1984

By W. W. Krysko

In order to calculate the critical particle size of lead oxide entrapped in lead, Stoke's Formula may be applied. All data were available except figures for the density of lead oxide at elevated temperatwes. The density of lead oxide was determined by means of dilatometmetrc and volumetric methods up to 1010°C. Graphs of the density of lead and lead oxide as well as the viscosity of lead are given and discussed, with the conclusion that the most unfavorable region for the separation of lead oxide from molten lead lies just above the melting point of lead. DURING previous investigations, particularly on the dedrossing of lead with aluminum1 and the oxygen solubility in lead,' the critical particle size of lead oxide which could be entrapped in solidifying lead was estimated by calculation, and it was shown that high values found for the oxygen content of lead may be due to the method of sampling and the entrapped particles of dross. Unfortunately, due to lack of data, an exact mathematical solution was not possible. The particle size which will separate under a given condition can be estimated from Stoke's Law, which states that where: d = diameter of the critical particle size ¦q = viscosity of lead in Poise V = constant velocity in cm sec-I g = 981 cm sec-2 61= specific gravity of lead 62= specific gravity of lead oxide The depth of the lead bath and the time before solidifying define the velocity. The viscosity of molten lead is known from earlier work by Krysko and is given in Table I. The specific gravity of lead is also known, see Table II. These values are according to Hofmann. A careful survey of literature revealed no values for the density of lead oxide at elevated temperatures. The present investigation was therefore conducted to provide this information. RESEARCH INVESTIGATIONS The density of lead oxide was determined from the following experiments: 1) Determination of the density of lead oxide at room temperature. 2) Dilatometric investigations on the same samples. 3) Determination of the shrinkage at the liquid-solid trans£ormation. 4) Density determinations on liquid lead oxide. 5) Time temperature curves during cooling. 1) The samples for the determination of the density of lead oxide in the solid state were prepared in the following manner. Molten lead oxide was cast into I hot mold which could be opened along the longitudinal (vertical) axis. The cast samples were cylinders of approximately 10 mm diam and approximately 80 mm length. The cylindrical hot mold was open at both ends and was placed on a large copper chill plate shortly before casting. The solidification of the lead oxides proceeded upwards without any formation of internal cavities. The sample was carefully checked with respect to density and crystalline appearance, and only the lower portions which were crystalline and free from porosity were used. The density was determined in a specially made pyknometer-like container, where the surplus liquid was squeezed out through an orifice approximately 1/10 mm in diameter. Mercury or water was used as the liquid. The densities of the samples were calculated from the weight, volume, and mean specific gravity of eight samples was 9.62 * 0.05 g cm"3 at 22"~. 2) The samples were machined to approximately 1 1/2 in. in length and fitted into a dilatometer. A

Jan 1, 1962

By Joseph C. Kieffer

The Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. Production oF Two Concentrates The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead con- centrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 1941, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. A rough outline of the flowsheet and reagents used is as follows: Minus ¾-in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1943

By T. Busch, R. A. Dodd

The solubility of hydrogen in pure iron and pure nickel, and of nitrogen in pure iron, has been determined and agrees well with earlier data. Nitrogen is insoluble in pure nickel and cobalt. The solubility of nitrogen in Fe-Ni alloys also confirms earlier- work. The solubility of hydrogen in Fe-Ni alloys increases non-linearly with increase in nickel content, but the solubility of hydrogen in Ni-Co and Fe-Co alloys reaches a minimum at 75 and 50 at. pet, respectively. The solubility of nitrogen in Fe-Co alloys decreases approximately linearly with increase in. cobalt content. Nitrogen is insoluble in Ni-Co alloys. Determined interaction parameters are in good agreement with predictions of Gokcen and Ohlani. THE solubility of hydrogen and nitrogen in liquid iron and iron alloys has been studied by various investigators.'-l' The method of solubility measuremerit due to Sievertsl is usually preferred when the vapor pressures of the liquid components are sufficiently small, but other techniques such as sampling the equilibrated melt and then analyzing by vacuum fusion have been used quite often. Previously reported data on the solubility of hydrogen and nitrogen in ostensibly pure liquid iron are summarized in Table I; certain of the quoted results were obtained by interpolation of the published data. Agreement between the various investigators is only fair, indicative of the experimental difficulties involved in obtaining gas solubility data. The only report found on the solubility of hydrogen in pure nickel is that of Sieverts.2 The solubility of nitrogen in iron-nickel alloys has received some attention, 10, 11 the results indicating that the solubility decreases with increase in nickel content, becoming zero for pure nickel. There is no published information on the solubility of these gases in either pure cobalt or alloys containing cobalt EXPERIMENTAL PROCEDURE Sieverts' method of solubility measurement was used throughout the investigation. The construction of the melting chamber is somewhat different from A. Optical pyrometer F. Alundum cover B. Vycor chamber G. Alumina crucible C. Furnace coils H. Alundum sand D. Glass water jacket I . Alundum thimble E. Chamber support J . Detachable vycor base sealed with de Khotinsky cement

Jan 1, 1961

By Joseph Jensen, J. B. Stevens

The history of the normal oil field is supposed to show an oil graph starting high in flush production, descending more or less steeply into the curve of settled production and dropping gradually to the vanishing point of economical operation. Together with this, somewhere in the early history of the field, there appears from a vanishing point a graph showing the production of water. During the period of settled production this graph rises higher and, toward the close, unless extensive work is done in the line of correction, rises far above the oil graph to the point at which the cost of operation terminates profitable pumping. Fields that start out with a high relative content of water are generally very short-lived. Fields that never develop a water problem are exceedingly rare. The McKittrick oil field, Kern County, California, with 840 acres of proved ground, 300 wells and a present recovery per acre of 94,598 bbl. from 1898 to Aug. 1, 1930, presents a study which is an apparent reversal of the outlined normal history. Though the history of the field now covers over 30 years of operation, it is still too early and the conditions too unique to project the graph of production to completion. The present conditions and directions of change are most interesting, in that the curve of oil production is remarkably flat and the curve of water invasion, after reaching an appalling height, has shown a definite reversal and a continued decline for 10 years. Early drilling in the McKittrick field was in or prior to 1898. Development continued steadily to 1918 when the present limitations of the field were determined. Shut-offs, according to accepted practice of the time, were made by driving the shoe into a shale stratum or into a tamped-in bridge of sand, rosin and clay. Records of early days speak of three waters: (1) surface water which was fresh; (2) an intermediate sulfur water, encountered below the top oil or tar sand; (3) bottom salt water. In different portions of the field any one of these waters let into a well by faulty completion might require immediate correction to obtain satisfactory production. In many wells,

Jan 1, 1931

By Joseph C. Kieffer

The Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. Production oF Two Concentrates The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead con- centrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 1941, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. A rough outline of the flowsheet and reagents used is as follows: Minus ¾-in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1943

By Joseph C. Kieffer

THE Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization, is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated. A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. PRODUCTION OF TWO CONCENTRATES The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead concentrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 194I, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. [ ] A rough outline of the flowsheet and reagents used is as follows: Minus ¾ -in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. I8 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1942

By F. G. Tryon

This paper treats only of the practicability of introducing a standard classification into the records of production and distribution of coal which we try to keep in the Bureau of Mines. From the point of view of gathering and analyzing statistics, the requirements of a satisfactory classification are that it shall be so definite as to eliminate the factor of arbitrary judgment, that it shall be reasonably simple and, finally, and most important, that it shall be understandable to the trade. In other words, to be woven in the statistical record it must be adapted to the raw material which flows in from the 7000-odd mines that produce the coal. The success of any scheme of classification, from the point of view of use, will depend largely on the degree to which it utilizes the accumulated experience of the trade and employs as far as may be possible the accepted trade designations. The experience of the Tidewater Coal Exchange during the war would be an excellent point of departure for a use classification of the coals of the Eastern Appalachians. Although the exchange long since passed out of existence, coal is still quoted and sold by the old pool numbers, and they have shown rather extraordinary vitality. Some years ago, in the Geological Survey, the experiment was tried of getting operators to classify their own coal by offering them a list of standard designations on the annual statistical questionnaire. The results were more amusing than informative. What with the confusion in terminology and the natural temptation to put one's best foot foremost, there was a general tendency to grade up the quality. Floods of semi-bituminous coal flowed in from many sources, millions of tons from districts where not a pound of that quality has ever been produced. The producers of semianthracite in Arkansas almost without exception would report their product as anthracite and their neighbors in the little Paris field, producing a fine blocky house coal averaging about 17 per cent, volatile, would say, "Our coal isn't anthracite; it's a semianthracite." Finally we discontinued the publication of those data as being more misleading than helpful.

Jan 1, 1930

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By George B. Clark

7.1-1. Introduction. The fundamentals of blasting involve both the properties of explosives and of the rock being blasted. While the knowledge of property correlation between rocks and explosives for most effective blasting is far more complete, many quantitative evaluations have been made. Four of the most important explosive properties appear to be energy density, bulk density, rate of energy release, and the pressure-time history of the gases produced. Important rock properties are density and porosity strength, and energy absorption properties, including the effective moduli of elasticity. Rock structure also has a marked effect on its breaking properties, i.e., joints, bedding, fractures, alteration, etc. Several mechanisms enter into rock fragmentation by blasting. These include slabbing, radial fracturing, crushing, and bursting by the gas bubble. All of these factors are closely related to properties of both explosives and rock. Slabbing depends upon the character of the first generated stress wave, whose shape and magnitude are a result of the pressure generated by the explosive, its time history, and the resultant response of the rock, including its ability to sustain the stress wave. Actual slabbing, in turn, is a function of the magnitude and shape of the pressure pulse and the tensile strength of rock. Further fragmentation depends to a great extent upon the amount of gas in the bubble and its energy and pressure. Blasting rounds are best designed by taking the above factors into consideration. This is effectively accomplished by use of cratering curves which relate breakage- parameters to the explosive energy. Optimum depths from single charge cratering curves must be adjusted to changes in shot geometry and related to multiple hole blasting. Blasting damage may occur from either air blast or ground waves, and in the latter ease may be due to direct vibration or to settlement caused by vibration. Technical information indicates that blasting damage is often

Jan 1, 1968

By Lyndon L. Foley

The proper spacing of oil wells is a problem of vital importance to the oil industry. Conservation demands a maximum recovery, while economic considerations attach primary importance to profitable extraction of oil. Formulas have been evolved,1-4 which attempt to solve the spacing problem mathematically, using reservoir characteristics as factors. Comparisons have been made of fields producing from supposedly similar sands, which have been drilled to varying densitiesl5,6 and also of different leases in the same field. 5-8 Intermediate wells have been drilled in old, depleted fields to test the efficiency of drainage by the original operation.9-11 Intermediate wells have been drilled also to obtain cores of the depleted sand for analysis, from which to learn the degree of efficiency of extraction. The problem is being attacked by many students, and along several different lines. Unfortunately, the fields now depleted were produced generally without restriction, and conclusions drawn from them may not apply to fields operated under restricted production. Reservoir conditions in a restricted field, especially reservoir pressures and pressure gradients within the reservoir, are quite different from those in a field produced to capacity. Many people have held the idea that the closer the spacing, the greater the recovery. This general statement is not always true, as other factors than well spacing enter into the recovery problem. Cutler,5 who has been quoted frequently by advocates of close spacing, limited his conclusions to gas-drive fields, and to the particular fields and spac-ings that he investigated. Hill and Sutton7 analyzed four tracts in the Powell field; the tract most closely drilled had the third largest recovery per acre-foot, and the tract with the widest spacing had the second largest recovery per acre-foot. A search of the references to well spacing in the publications of the U. S. Bureau of Mines5,13-19 discloses repeated condemnations of the wastefulness of the practice of town-lot drilling.

Jan 1, 1938

By A. Patton

Introduction THE use of roll scale in the Bessemer process dates back, to the "best of our knowledge, at least 20 years. It was first used by the Ohio Steel Co.; Youngstown, Ohio (now the Ohio Works of the Carnegie Steel Co.) under the direction of Sam, MacDonald, Superintendent of the Bessemer Department at these works. Two 10-ton vessels and one blowing engine capable of blowing one heat at a time were employed. The object of using the scale was to -shorten the length of the blow; or in other words, to increase the production with the same equipment. Various means were tried out for introducing the roll scale into the bath of molten iron: It was shoveled into the vessel before the heat was charged, so that the metal would flow over the scale; it was shoveled into the bath after the vessel was turned up; it Was dumped into the empty iron ladle by the wheelbarrow-load, and at times wars dumped on top of the molten metal in the iron ladle. But the practice of introducing the scale into the iron ladle had to be abandoned on account of danger from explosions and of skulling the -ladles. It was soon learned that the proper place to charge the scale was in the empty vessel, so that when the molten iron was poured into the vessel it flowed over the scale, causing a considerable reaction to take place before the heat was turned up. Eventually, cylindrical chutes similar to those now in use were installed. Into these chutes the scale is dumped and carried into the empty vessel. Before this convenient means of introducing the scale was adopted, the Ohio Works had satisfactorily demonstrated that roll scale would increase production, by blowing 107 heats in one 12-hr. turn (1,087 tons) with one blowing engine, blowing one heat at a time; whereas, prior to the use of scale, the best practice at these works was about 80 heats under the same conditions.

Jan 2, 1917

By Charles L. Harness

MINERAL pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and Limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, such as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-Limonite (2Fe203.H20 to Fe203.4H20), hematite (Fe203), or magnetite (Fe203.FeO). Man's first permanent coloring materials were earth pigments- the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands

Jan 1, 1949

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By Edgar L. Newhouse

The lead smeltery at East Helena, Mont., controlled by the American Smelting & Refining Co. since 1899, has been in continuous operation for the past 25 years. Most of the old smelting and roasting practices have been superseded by newer and more modern methods, but on account of the difficulties involved in changing the original construction, some of the methods in use of handling materials are not the most modern. This plant, however, is particularly interesting as being one of the few essentially lead smelteries in the United States. At Federal, Ill., Collins-ville, Herculaneum, and possibly other places, similar work is being done, but it is doubtful whether any of them produces as much lead as the East Helena plant, whose monthly production averages 6,500 tons. The situation, 5 miles east of Helena, is convenient to both the Great Northern and Northern Pacific railroads, while the electric power is obtained from Canyon Ferry, 12 miles east on the Missouri river. Local quarries supply the requisite amount of lime rock, which the contracts require to be crushed to 5 in. Of the 450 men on the monthly pay roll, a census showed 200 Austrians, 110 Americans, and 30 Italians, the balance being made up of miscellaneous nationalities. The ore supply is mainly derived from the Coeur d'Alene mines in Idaho, and consists of crude ore, coarse and fine concentrates, middlings, and slimes. About one-half of the total output of the Coeur d'Alene camp is sent to East Helena. An average analysis of these ores gives approximately 40 per cent. lead and 11 per cent. sulphur. Local shipments, varying from month to month, are mostly highly siliceous gold and silver ores carrying little lead. Small shippers, leasers of old mines, and prospectors are very numerous throughout Montana, and it is the policy of the company to encourage these men by every possible means, including the free sampling and analysis of their ores and aid in the development of their mines and prospects, whenever their results show promise.

Jan 1, 1915

By John V. Beall

Homeland of the Republic of China, the island of Taiwan looks on the map like a seal, muzzle pointed south, resting complacently on the emerald waters of the China Sea. Any notion of placidness is quickly dispelled by going to that country where the visitor gains the impression of almost violent busyness in tearing up streets, pushing up buildings and tilling the fields. Driving from the airport downtown to Taipei, the capital city, one sees roads, streets and thorough-fares which seethe with bizarre traffic. From water buffaloes to buses, transportation takes every conceivable shape, size and color in between. The load being transported need not conform in any way to the capabilities of the vehicle. Twenty- foot lengths of pipe may be trans- ported on a bicycle. A family of five may go to town on a motor- cycle. Impossible? Count them. The streets and buildings of the city appear unrestrained, or without margins. Shops do not end at the doorway but overflow with a variety of goods onto the sidewalks and into the streets where the marginal traffic, on foot or on wheels, intertwines unconcernedly with the flotsam from the shops. Signs, dry goods, hardware and the continuous hubbub make the view colorful, lighthearted and fascinating. The island is 230 miles long by 75 miles wide with a central mountain spine. To the east, the mountains descend steeply to the ocean whereas to the west, beyond the foothills, there is a broad coastal plain. Only about 25% of the land is suitable for cultivation but the tropical climate permits several harvests a year. At the same time the mountains, which are high enough to sometimes have snow, offer an agreeable change of temperature. In this setting, society has created an economy that is growing at such a rate on all fronts that it would seem to be fairly bursting at the seams.

Jan 9, 1969