Search Documents

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

Oil-well driller with extensive experience in this line of work. Location, Bolivia, South America. Salary depends on experience. R.-789. Mining Engineer, with geological knowledge, who can locate suitable spots for drilling oil wells. Location, Bolivia, South America. Salary depends on man. R-788. Construction Engineer, mechanical or civil engineer with experience in installing oil plants for foreign field. Must be able to install entire equipment including tanks, piping, buildings, etc. Salary depends on experience. R-782. Geologist, competent petrographer for micropetrographic work and training of two assistant students under the direction of the Director of a Geological Institute. Engagement is for six months with option on the part of the Director for an equal period: Location, Mexico. Salary, 450 pesos Mexican gold ($225 per month). R-765. Operating Mechanical Electrical Engineer, with extensive experience in charge of the maintenance, repair, and betterment of all mechanical and electrical equipment on mining operations. Desirable that the man have had this experience in connection with phosphate mining. Applicant must be competent to direct shop repairs on motors and generators, including rewinding, the building and maintenance of transmission lines, etc. Must also have ample machine-shop experience to enable him to direct repairs of light locomotives, steam shovels, brown hoists, caterpillar tractors, and auto trucks. Duties will include the betterment and maintenance of phosphate-rock washers and rotary-work dryers. The applicant must also be competent to conduct efficiency tests on all such equipment and be enabled to interpret data collected. Splendid opportunity for the right type of man. Climate and living conditions excellent. The company will furnish house rent free, including light .and water. Location, Florida. Salary depends on experience. R-854.

Jan 7, 1919

By James T. Waber, Allen C. Larson, Karl Gschneidner, Margaret Y. Prince

The original graphical method proposed by Darken and Gurry for predicting which elements are soluble in a given element was slightly modified and was used to predict terminal solubilities in 1455 known binary combinations. it was found that the modified Darken and Gurry method had a reliability of 61.7 pct in predicting extensive solid solubility (greater than 5 at. pct) and of 84.8pct in predicting limited solid solubility (less than 5 at. pct), an over-all reliability percentage of 76.6. Using the same experimental data, it was found that using only the simple Hume-Rothery size-effect criterion was 50.1 pct reliable in predicting extensive solid solubility, only slightly better than a purely random choice. and 90.3 pct reliable for predicting limited solid solubility, an over-all reliability percentage of 67.6. THE first rational rules for determining a priori whether two metals are not freely soluble in the solid state were announced by Hume-Rothery and coworkers.1,2 These well-known rules have been accorded a special place in metallurgical literature. Since the "electronegative" and "relative valence effect" rules of Hume-Rothery were only qualitative in nature it was difficult to use them in a quantitative analysis. The next major step was made by Darken and gurry3 and apparently went unexplored for a number of years. They prepared graphs illustrating the influence of both electronegativity and size difference on the solubility of elements in silver, magnesium, and aluminum, and they drew elliptical figures, whose maximum width was ±15 pct of the solvent radius and the maximum height was ±0.4 electronegativity units. The purpose of the present paper is to assess and compare the effectiveness of using the simple size-factor and the Darken-Gurry criteria to predict which elements will be soluble and insoluble in a given solute. In 1957, waber4 prepared Darken-Gurry plots for determining the solutes that were likely to be soluble in 6 and plutonium and introduced an inner ellipse as an aid to determining which elements should be soluble to a considerable extent. As illustrated in Fig. 1, the major axis of the outer ellipse corresponded to ±0.4 electronegativity units (OD) while the minor axis corresponded to ±15 pct of the radius of the solvent phase (OB). This simultaneous "action" of the two Hume-Rothery criteria was used to indicate which elements would have little or no solubility in the host lattice, namely those elements whose points lay outside this ellipse. An inner ellipse, "centered" over the same point of the solvent was drawn with ±0.2 electronegativity units (OC) and ±8 pct (OA) as the major and minor axes. Solutes with points lying within the inner ellipse were expected to be capable of forming extensive solid solutions with the host element. Use of this method of applying the earlier Hume-Rothery criteria was moderately successful for plutonium. For 6-phase plutonium, only one element out of the eight predicted to be extensively soluble was known to be almost insoluble, and of the sixteen elements predicted to have more restricted solubility, five were known to be essentially insoluble. The success of discerning solubility in the E phase by this method was comparable. One prediction made on the basis of this analysis was that the heavier rare earth metals, such as holmium, erbium, and thulium, should be soluble in the 6 phase, whereas the lighter rare earth elements, such as lanthanum or

Jan 1, 1963

By Ernest F. Burchard

In connection with the work of testing structural materials for the use of the U. S. government at the laboratories of the technologic branch of the U. S. Geological Survey at St. Louis, Mo., from September, 1904, to April, 1909, and since then at Pittsburg, Pa., large quantities of sand, gravel, and crushed stone have been needed from time to time, besides samples of building-stone, clays, and other quarry-products. In many instances it has been necessary to obtain single samples of sand, gravel, or crushed stone in lots of a car-load or more. For obvious reasons all these collections have had to be made by a representative of the Survey. As the work progressed it was found essential that numerous geologic data should be gathered regarding the materials collected, in order that they might be properly classified as to kind of material, source, geologic age, etc., and that they might be rated according to quantity available, accessibility to transportation facilities, approximate costs, suitability for special purposes, etc., and that notes might be taken regarding undeveloped deposits of possible value. Furthermore, it mas desired that the selection of materials for tests should be made broadly, so as to cover, first, the representative types of material, and later, if possible, the typical materials of the more important building-centers in the United States. In order to insure a certain degree of uniformity in this work and economy of effort and expense, it was decided that as much of the sampling as was practicable should be done by a member of the geologic branch, whose regular field-trips could be combined conveniently with those necessary for procuring materials for the laboratory. During parts of the last three years 1 have been engaged in field-work of this sort.

Jan 1, 1911

By C. H. Li, S. H. Bendel, J. A. Sartell

Small additions of Mg to a 62 Cu-38 Ni alloy reduce the oxidation yates drastically between 500° and 850°C. Metallographic examination of the oxide scale disclosed a continuous network, identified by X-ray diffraction as (Ni, Mg)O solid solutions, located along the former alloy grain boundaries. This network acts as a barrier to diffusion. It is thought to result from the segregation of mg to the alloy grain boundaries. Oxidation occurs preferentially in these regions because of the presence of this more active element. To substantiate these ideas, homogenized alloys ulere oxidized. No oxide network was produced and oxidation rates were the same as for the parent 62 Cu-38 Ni alloy. An interesting aspect of the oxidation of the 62 Cu-38 Ni alloy previously described by the present authors, is the relationship between oxidation kinetics and changes in the microstructure of the oxide.' The oxide scale on these alloys consists of two layers: a thin layer of CuO outside a much thicker layer of Cu20 in which particles of NiO are dispersed. In addition, immediately beneath the oxide-metal interface there is an internally oxidized zone in which NiO particles are dispersed in a copper-rich alloy matrix. Experimental observations on the growth of the individual layers under isothermal conditions have led to the conclusion that the rate-determining step in the oxidation of this alloy is the diffusion of anions through the Cu20 layer. It has been found that this diffusion rate is increased by the recrystallization of the outer CuO layer. Willardson and Gorton have reported that the addition of magnesium to the 62 Cu-38 Ni alloy causes a decrease in the oxidation rate.2 The present investigation was undertaken in order to determine the mechanism by which magnesium additions improve the oxidation resistance of the 62 Cu-38 Ni alloy. EXPERIMENTAL PROCEDURE Fifty-gram ingots of Cu-Ni alloys were prepared by vacuum melting materials of 99.999+ pct purity. These ingots were then remelted in a He atmos- phere and magnesium added in the form of a previously prepared and analyzed Cu-Mg master alloy. This procedure was necessitated by the high reactivity of pure magnesium at high temperatures. The proportion of the alloying elements was adjusted so as to obtain alloys with the desired magnesium content while maintaining a Cu-Ni ratio of 62 :38 by weight. (All alloy compositions will be given in weight percent.) Since it was considered desirable to study the oxidation of only single-phase, solid-solution alloys, it was necessary first to determine the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy. A series of melts with various magnesium contents was made, homogenized by annealing for 48 hr at 975OC, then cooled in the furnace. Metallographic samples were prepared, etched in a potassium dichromate solution and examined at XI500 for the presence of a second phase. The alloys were then chemically analyzed and it was found that the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy was 1 pct Mg. The ingots containing less than 1 pct Mg (0.19, 0.29, 0.58, and 0.87 pct Mg) were cold-rolled down to thicknesses suitable for oxidation experiments and specimens for gravimetric studies were cut to dimensions of 3.0 by 1.5 by 0.05 cm, specimens for inert marker studies, 0.6 by 0.6 by 0.17 cm. These were heat-treated in a protective atmosphere at a temperature (975" C) well above the oxidation temperatures and furnace-cooled to insure structural stability of the alloy during oxidation. Immediately prior to oxidation, the specimens were chemically cleaned by immersion for 1 min in a solution of 2 parts nitric acid, 1 part acetic

Jan 1, 1961

By C. K. Leith

THE questions as to what grades of ore it pays to conserve for the future, and the valuation of low-grade reserves, are becoming immediate and definite as applied to individual ore deposits, and seem to call for some sort of quantitative answer. Both opinion and practice involving these questions differ widely. The number of variables in this problem is so large that final solution will perhaps never be agreed upon, yet there seem to me to be certain controlling factors which can be placed in quantitative relation and serve to reduce the number of variables which it is necessary to consider in a given instance. I assume that it will not pay either for the individual or for the State to conserve any ore when the present cost of conservation (by stock piling or otherwise), when compounded at 6 per cent. interest for the number of years which would elapse before this ore is used, will exceed the profit which the ore will yield when it is used. It may be urged that any loss to the individual may be made up in gain to the State. This might be true if there was any definite limit to the amount of iron ore, but when we remember that iron makes up .4 per cent. of all the rocks of the earth and the amount of rock carrying iron in excess of 20 per cent. is for practical purposes, unlimited, it is apparent that posterity is assured of its iron ore. The changes will be mainly in methods and cost of extracting the ore. Therefore, any expenditure of money or effort now, which when compounded will exceed the worth of the effort or money needed in the future to utilize the iron, is a net loss both to the individual and to the community.

Jan 2, 1914

By M. E. Volin, D. W. Fuerstenau, A. L. Mular

This paper presents the results of an investigation of the effect of feed size on the integral rate at which feed material is dry ground in a laboratory rod mill. The data are interpreted in terms of the Gaudin-Meloy distribution equation. The equation, Mo — Mt/t = Aoxo r-1, is found to hold for feed sizes smaller than some critical size or for grinding times larger than some critical time. It is shown that a feed grindability is related to this critical size, which appears to be the transition between predominately impact and predominately attrition grinding. Detailed research on feed size effects in comminution has been rather limited. Gaudin1 ground single-sieve fractions of quartz for extended time periods (four hours) in a laboratory ball mill. His work, which was designed to study the nature of size distributions, showed that there is a critical feed size above which comminution occurs primarily by attrition. For his system, the critical size was about 2-mm when using 22-mm balls. In a more recent investigation2 single-sieve fractions of quartz were ground in a laboratory rod mill for constant time periods (15 min) to determine how feed size affects the grindability of the material. This work showed that grindability is essentially independent of feed size in the rod mill after this moderately long grinding period. To further clarify this observation, a study in which feed size and grinding times are varied over a fairly wide range, and particularly, a study of the dependence of the integral rate of grinding on feed size during the initial stages of rod milling is necessary. For an analysis of such data, it is desirable to use a parameter which is very sensitive to change during the initial grinding period when reduction ratios are

Jan 1, 1964

Jan 1, 1942

By Rudolph G. Wuerker

THE scarcity of values of tensile strength of rocks has been explained by the lack of successful testing procedures. In the case of mine rock a description is given' of the difficulties encountered in testing a cylindrical specimen, such as a core, by conventional methods. Over a period of years the following method has given definite and reproducible results with the weakest as well as with the strongest rocks. It does not completely supersede the use of cores with special fixtures but is a supplement in all cases where cores cannot be obtained, as from soft rocks, or in cases where it is less expensive to prepare test specimens by cutting them out of the rock instead of drilling cores. Principle and equipment are the same as for the test for tensile strength of hydraulic-cement mortar.' The test specimen, Fig. 1, has the shape of a briquet. While in the original cement mortar test the briquet is cast in a special mold, it is prepared from rocks in different ways, depending on how easily they can be cut and shaped. Soft rocks, which cannot be core-drilled with a carboloy or diamond bit, are simply hand-cut. Only two dimensions need be watched. The first is the 1-in. diam at the narrowest cross-section of the briquet. The other critical measure is the radius of curvature of the waistline, as the roller supports in the grips have a fixed distance. This radius is ground out of the solid by means of a carborundum grinding wheel having a 3/4-in. radius. Medium hard rocks can be core-drilled with a carboloy bit. The resulting core can be used for nondestructive sonic testing first, and after that for any destructive test. By using an EX-bit and by carefully placing the coreholes, preferably by using a tenplate such as shown in Fig. 1, it is possible to obtain from the rock a punched sample from which numerous tensile briquets can be made. The outside radius of the EX-bit differs from the radius of curvature of the briquet by 1/8 in., but this still permits placing and aligning the specimen in the grips. In the case of bedded rocks the core might have bedding planes normal to the plane of the briquets, and rocks can be tested in any arrangement of the bedding planes desired. Hard rocks, limestones, igneous, and metamor-whic rocks can only be diamond-drilled or diamond-cut. Here the method of getting the tension briquets by accurate placing of EX-drill holes is especially economical. The tops of the briquets made from hard rocks cannot be rounded; they are straight cuts made with a diamond cut-off saw and rounded off on a polishing wheel. Results: As long as specimens broke over the waistline the results were considered acceptable. Further statistical treatment of the tests' showed a satisfactory percentage of standard deviation. The tensile strength values obtained by this method do not represent true values because of the stress concentration caused by the curvature of the side of the piece and because of the closeness of the grips. The ratio of maximum to average stress at the plane of failure has been determined to be about 1.75." All tensile strength values listed in Table I are corrected accordingly. To avoid this stress-concentration, if there are a sufficient number of cores, tensile strength can be measured by imbedding the cores in mortar in the two outer briquets in the gangmold.4 Strain-Measurements: The applicability of the briquet specimens for strain observations was tested in the case of sandstone and shale. Two element Rosette SR-4 strain gages were used. Young's modulus and Poisson's ratio, both in tension, were computed and found to be different from those in compression, determined during the same test series and from the same rock, see Table I. References 1 L. Obert, S. L. Windes. and W. I. Duvall: Standardized Tests for Determining the Physical Properties of Mine Rock. U. S. Bur. Mines R.I. 3891 (1946). 2 Test for Tensile Strength of Hydraulic-Cement Mortar, ASTM Standard C 190-44. S F. O. Auderegg, R. Weller, and B. Fried: Tension Specimen Shape and Apparent Strength. Proc. ASTM 11939) 39, pp. 1261-1269. 4 API Code 32.

Jan 1, 1956

By J. T. Norton, J. G. McMullin

The ternary system of gold-silver-copper is characterized by a solid solubility gap and a two phase region in which copper-poor and silver-poor phases coexist. At about 30 pct gold, the two phases become mutually soluble at temperatures below the melting temperature. As the gold content is increased, the solubility temperature of the alloys decreases until at about 80 pct gold, the two phases are soluble down to the lowest temperature at which the alloys will recrystallize. Although the general form of the two phase region is known, its boundaries do not seem to have been investigated extensively. In an X ray diffraction study, Masing and Kloiberl have outlined the boundaries of this two phase field at 400 and 750°C. Using only microscopic techniques, Pickus and Pickus2 determined a vertical section of the ternary diagram showing the 14 kt alloys (58.3 pct gold). These two reports are riot in complete agreement. It has been shown3 that some of the ternary alloys are susceptible to age hardening and that the hardening is caused by the separation of a homogeneous alloy into two phases at the aging temperature. While the gold-copper binary system is an outstanding example of super lattice formation, Hultgren4 has shown that a few per cent of silver added to gold-copper destroys the tendency for ordering. Because of the age hardening possibilities of these alloys, it seemed advisable to investigate the boundaries of the two phase field more in detail using an X ray diffraction method, so as to permit a better understanding of the aging phenomena and enable predictions as to the behavior of other alloys to be made. This is especially true for the 18 kt alloys (75.0 pct Au) at the lower temperatures since they are known to exhibit age hardening. Twelve ternary alloys were prepared having the compositions shown in Table 1 and graphically in Fig 1. The gold used was fine gold bars supplied by Handy and Harmon. The silver was a bar of high purity silver from the U. S. Bureau of Standards. The copper was a bar of vacuum-treated, high conductivity copper from the National Research Corporation. The pure metals in the form of powder were weighed out in proper proportions and melted in graphite in a high frequency induction vacuum furnace. They were heated to 1100°C and slowly cooled. The ingots were then removed from the crucible, inverted, returned to the crucible and remelted. This remelting procedure was intended to reduce segregation in the ingots. After remelting, the ingots were checked for weight loss. The weight loss in each ten gram ingot was held to less than 25 mg. The remelted ingots were cold rolled and then given a homogenizing heat treatment of 16 hr at 760°C to remove any remaining segregation. Powder specimens were prepared by cutting the ingots with a fine file, one half the required amount of powder being taken from each end of the ingots. When the X ray diffraction pattern showed any difference in lattice constant between the ends of the ingot, the ingot was remelted and given an additional homogenization treatment. All powder samples were sealed in evacuated pyrex tubes for heat treatment. Ordinary pyrex proved satisfactory for temperatures up to 650°C but above that temperature it was necessary to use a special high temperature pyrex glass. Annealing at temperatures below 500°C was done in a salt bath whereas for temperatures of 500°C and above an electric muffle furnace was used. In both furnaces the temperature control was ± 5°C. In all annealing treatments samples of cold worked powder were placed in a furnace which was already at temperature. In this manner the specimens recrystallized directly to the equilibrium structure for that temperature. Time at temperature was selected so as to allow complete recrystallization, but very little grain growth. Specimens were quenched from the annealing temperatures by breaking the pyrex tubes in cold water. X ray diffraction photograms were made of all the heat treated powders using copper radiation and a Phragmen

Jan 1, 1950

By J. B. Cheatham, J. G. Yarbrough

Although adequate removal of cuttings from beneath a drill bit is important for efficient drilling operations, very little basic data are available relative to the fundamentals of chip removal by hydraulic jets. A discussion is presented in this paper of an experimental investigation of the jetting action of hydraulic jets in removing loose particles from the bottom of a cylindrical hole. Conditions for which the jet is no longer capable of removing chips from the bottom of the hole are determined. This situation represents equilibrium between the chip removal force and chip Bolddown forces such as gravity and pressure. In most of the tests loose particles were jetted with water or a water-glycerine mixture to determine the dependence of chip removal on hole size, jet size, height of jet off bottom of hole, flow rate, particle density and fluid viscosity. ,A test with a pressurized mud system indicated that relatively low pressures can completely overcome the removal action of a hydraulic jet. Although the system studied herein is not directly applicable to a rotary drill bit, the work with such simplified systems can provide a better understanding of the chip removal action of jets, and with logical extensions it may provide a reasonable basis for the best use of fluid jets in drilling. INTRODUCTION The primary deterrent to maximum drilling rates is the inability of the drilling system to remove rock cuttings efficiently enough to prevent interference with the drilling action.1-2 The objective of chip removal studies is to permit predicting and controlling removal forces under downhole drilling conditions. Conditions at the bottom of a hole during rotary drilling are exceedingly complex and are not likely to be described in a quantitative way by investigations in terms of the total drilling action until a better understanding is developed of the simplified components of the problem.3 The present study is concerned with the elementary condition of removal of chips by a single central jet. Even this relatively simple model provides mathematical difficulties because of the turbulent nature of the flow from the jet and because of the shape of the bottom of the hole beneath the jet. Theoretical and experimental studies have been made of turbulent jets impinging normally on an infinite body and deductions based on analytical solutions to simplified problems can give some insight into the problem of cutting removal by a jet. However, because of the present lack of understanding of the behavior of the interaction between the fluid jet and the chips being removed, an experimental approach was chosen for the present study. Methods have been developed for maximizing hydraulic horsepower, impact force and jet velocity; but whether maximizing these parameters maximizes chip removal with present drilling bits has not been demonstrated. Simplifying the problem of chip removal may make it possible to develop some understanding of the manner in which the jet velocity is dissipated. Better understanding of a simple case should materially assist in extending analysis to more complicated cases. Thus, we are not concerned in the present study with the rock fracturing process itself but only with the removal of the debris from the bottom of the hole. A problem which is quite similar to the chip removal problem is the suspension of solids in stirred vessels. This problem has been studied by the chemical industry and correlations have been obtained by dimensional analysis which permit the design of mixing vats7 An approach similar to that used in the mixing vat problem is used in the analysis of the jetting data in the present paper. EXPERIMENTAL PROCEDURE The test equipment arrangement shown sche-matically in Fig. 1 allows the jetting action to remove particles until an equilibrium height is attained for each combination of hole size, jet size and flow rate.*** Equilibrium conditions require that the removal force is unable to remove additional particles. This balance between holddown and removal forces implies a relationship between the two forces which is constant for the particular system. When the holddown forces are constant,

Jan 1, 1965

By E. L. Kamen, H. D. Kessler, M. Hansen, D. J. McPherson

The highly reactive Ti-Mo and Ti-Cb alloys were prepared and heat treated under protective conditions. Phase diagrams were established based on micrographic and X-ray diffraction analysis and detection of incipient melting. ß titanium forms a continuous series of solid solutions with both molybdenum and columbium, whereas these metals are only slightly soluble in the a titanium modification. PREVIOUS work on the Ti-Mo and Ti-Cb systems was very limited and is discussed in succeeding sections of this paper relating to the respective phase diagrams. The diagrams in the present work were determined principally by micrographic analysis, because other methods such as thermal analysis and dilatometry are not suitable, due to the low diffusion rates of these alloys in the transformation range. X-ray analysis was believed less useful than micrographic analysis because: 1—On quenching certain high titanium alloys from above their transformation range, the body-centered cubic ß phase decomposes into acicular a (hexagonal close-packed) which room temperature X-ray diffraction techniques cannot differentiate from isothermal a. 2— High temperature X-ray techniques might be used, but are difficult to apply and are subject to error because of the high reactivity of titanium with gases such as oxygen and nitrogen. Although metallo-graphic study was the basic method used, X-ray diffraction analysis was applied to a limited extent, to further substantiate the findings. The transformation ranges on the titanium side of the Ti-Cb and Ti-Mo systems were studied both with DuPont Process A (magnesium-reduced) titanium alloys and with iodide titanium alloys. The Process A metal was used chiefly to bracket the transformation range in order to reduce the number of alloys given a particular treatment for the more accurate final study with iodide titanium alloys. Experimental Procedure The analyses of the metals used in the preparation of alloys for this study are presented in Table I. Melting Practice: Early in the work, a consumable electrode, arc melting furnace was used in the preparation of the Process A Ti-base Mo and Cb alloys. This type of furnace has been described by other investigators.', ' One of the major difficulties of the consumable electrode melting process was the prep- aration of homogeneous electrodes (with the mixture of coarse titanium sponge and fine powder alloying addition) which would give homogeneous ingots. Composition gradients encountered may have been due to a tendency for powdered alloying metals to drop away from the electrode in handling. This difficulty in the preparation of homogeneous alloys was overcome by the use of a nonconsumable electrode furnace for later work. This furnace is similar to the one used by Mc-Pherson and Fontana a Ohio State University. A diagram of the nonconsumable electrode arc furnace is given elsewhere.' The source of power was a 400 amp dc welding generator. Electrode tips of tungsten (% in. in diam) were used for all columbium melts and for a limited number of molybdenum melts. Molybdenum tips were used for the majority of molybdenum alloy melts. Columbium tipped electrodes were tried, but disintegrated rapidly at currents above 300 amp. In the Process A titanium melting practice the metals were charged into the water-cooled spun copper crucible in the following forms: l—titanium: sponge (—4 + 16 mesh); 2—molybdenum: sections of 0.003 in. sheet (approximately ½ in. sq); and 3— columbium: powder compacts (? in. lumps broken from large section). After alternately evacuating and purging the furnace several times with argon or helium, the arc was struck against the metal charge,

Jan 1, 1952

By Harry R. Hall

THE proposition to make pig-iron from magnetic concentrates and cobbed ore with charcoal-fuel weighing from 12 to 20 lb. per bushel is, on the face of it, not inviting; but the successful work that has been done under these adverse conditions warrants a permanent record in our Transactions, especially as it furnishes a comparison with, coke blast-furnace practice under similar conditions. The record of the furnace-practice is briefly summarized as follows:-The charcoal was made of hemlock, pine, spruce, balsam, maple, beech and birch woods. All the concentrates containing from 62 to 65 per cent. of iron would pass in. screen, of which about 34 per cent.. would pass an 80-mesh sieve. The cobbed ore, varying in composition from 32 to 47 per cent. metallic iron and from 23 to 32 per cent. of. silica, would pass through a I-in. ring, of which about 25 per cent. would pass a 1/8 in. screen. The furnace was blown in October 20,1903, with charcoal which was supposed to weigh when dry 18 lb. to the bushel. Some charcoal similar to this was stored in the stock-house for about a year and was then found to weigh 12 lb. per bushel. During the first 10 days of the blast, the furnace produced 362 tons of pig-iron, using 200 bushels of charcoal per ton of iron. From November 1st to 12th, the volume of the blast was increased gradually from 2,808 to 5,460 cu. ft. per minute, with practically no increase of output. The silicon-content of the resultant pig-iron averaged 0.75 per cent., with sulphur about 0.035 per cent. A supply of freshly-burned dry charcoal was then used which increased the silicon-content and lowered

Sep 1, 1905

By Robert W. Hunt

(Cleveland meeting, October, 1912.) PERHAPS of all the scientific economic questions which have been claiming the attention of capitalists, metallurgists, manu-facturers, directors of public utilities, and the general public of America, during the last few years, none have been of more importance than the one relating to the wear and safety of steel rails. The discovery of the Bessemer process made possible modern railway development. In that growth, as has generally happened in all progressive movements, ill its department have not remained equally balanced. Iron rails permitted the construction of roadways for the passage of power-driven vehicles. In time the speed and weight of such carriages proved too much for the wearing-qualities of the rails, and the limit of railway capacity seemed to have been reached. Bessemer made his invention, which was soon perfected and developed, especially as related to steel rails, and thereby increased the limit of capacity, acid vastly greater railway progress was, made possible. The Siemens-Martin open-hearth process followed, and was later supplemented by the Thomas-Gilchrist basic improvement. For a time the Bessemer steel rails of commerce Were, more than equal to all that was asked of them, but this did not long continue, as evidenced by the records in our Transactions. Revolutionary changes occurred in the industrial world, and in no part of it more than in steel-rail manufacture. Great and powerful commercial combinations were made, whose financial resources made possible the supplanting of the then most efficient blast-furnaces, steel-works, mid mills, by others of theretofore unimagined capacity. Old traditions and practices of steel-making were wiped away, and, in too many cases, output was apparently the chief aim, with the result that much dissatisfaction with the wear and safety of rails was felt by railway officials, and the general public was concerned as to its safety when traveling. The climatic conditions of the winter

Dec 1, 1912

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By Newell Alford

THE data in this paper were collected to show both the volume and speed with which bituminous mines have indefinitely suspended operation while economic advantage in the industry has so gravely declined. The study was limited to the bituminous coal-mining states east of the Mississippi River, wherein conditions affecting production and demand are more common respectively to all of the mining districts included and represent about 95 per cent of the nation's coal mining. Data for the compilation of these statistics and for the construction of these graphs have been obtained in all cases from state mine depart-ment reports, except from those of Ohio and Virginia. In Virginia essential individual mine data were secured from an authentic source, but no individual Ohio mine information is obtainable, because all Ohio fact-gathering agencies are prohibited by law from revealing such data. In other states the facts were tabulated and later checked with the cooperation of Chief Mine Inspectors. In all, excluding Ohio, over 17,000 individual annual mine returns were examined. Special infor-mation was secured from each state mine department about suspensions in 1932. Accurate information was not available from all states about mine abandonment due to exhaustion of coal reserves, and while these were completed for several states, it has not been shown because it was not perfected for all states. However, the total observed sample was comprehensive enough to show that exhaustion accounts for a very limited part of the suspended production. Wherever mention is made of "suspended production" the largest annual output of the mine in the five years prior to suspension has been taken as the measure of its probable production had it continued to operate. A mine is not regarded in this category, as having suspended, when it merely ceases to produce. The word "suspension" is used only where there is a complete abandonment of activity for an indefinite period, as evidenced by the fact that both ventilation and pumping are discontinued.

Jan 1, 1933

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By Robert B. Fulton

Commercially, celestite (SrSO4) is the predominant strontium mineral. Among other strontium-bearing minerals, only strontianite (SrCO3) occurs commonly; however, it is rarely an item of commerce. Production of celestite is principally in Mexico, Spain, and Turkey. An attempt to produce celestite in Canada was unsuccessful. The United States, which is wholly dependent on imports, chiefly from Mexico (99%), is the largest consumer of strontium. Lesser quantities are consumed in Japan and Europe. The Federal Republic of Germany is the principal source of strontium compounds imported to the US. Uses The principal uses of strontium are for the manufacture of strontium carbonate and nitrate. Carbonate is used in glass for TV tube face plates and in ceramic ferrites for magnets. Nitrate is used in pyrotechnics, mainly in safety flares, to which it imparts a characteristic brilliant red color. Minor amounts of strontium compounds are used in electrolytic zinc manufacturing where the carbonate is used to remove unwanted lead. Small quantities are consumed in greases, ceramics, soaps, alloys, and pharmaceuticals. Specifications Typical celestite specifications for the carbonate and nitrate markets are shown in Table 1. Specifications of manufactured carbonate, sold in two grades, one to the glass industry and the other for ceramic ferrites, are shown in Table 2. Both grades of carbonate are shipped in palletized 50-lb bags. Glass grade material is shipped in bulk by rail. [ ] Manufacturing Processes The following description is adapted from Anon. (1980) . The manufacturing process for strontium carbonate and strontium nitrate chemicals is conceptually simple. Strontium nitrate is made from strontium carbonate in two additional steps. The production process begins with celestite, the natural form of strontium sulfate. In the first step the ore is crushed, ground, and mixed with coke. This mixture is then fed into a kiln where the ore is reduced at high temperatures to strontium sulfide; the coke is added to the ore as a source of energy and carbon. The carbon combines with the oxygen [ ]

Jan 1, 1983