Search Documents

By Arthur B. Yates

Diamond drilling has advanced and expanded during the past few yean. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. Control A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing— even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved. however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the

Jan 1, 1946

By C. E. Birchenall, H. M. Schadel

Vapor pressure of silver over silver-gold alloys has been measured over a range of temperatures for four compositions. Orifice effusion has been compared with electromotive force measurement as a means for determining thermodynamic activities in these solid metallic alloys. Correlated activity coefficients are given for silver-gold alloys for the temperature range 200' to 1000°C. SOUND development of a technique for the measurement of some property of matter requires a comparison with other recognized procedures which have been used to measure the same property. Such a check is especially useful if the assumptions on which the applications stand are basically different for the two methods. Agreement in the results tends to confirm both sets of assumptions. The electromotive force method for determining thermodynamic activities depends upon the reversibility of the electrode processes and a knowledge of the valence states involved. The orifice effusion technique of determining vapor pressures requires that certain mean free path conditions be met, that the state of association of the vapor be known, and that efficient collection of vapors be maintained. Thus the requirements are quite different in nature. Although procedures often exist by which the fulfillment of these conditions may be tested internally, agreement of thermodynamic activities for a single system obtained by both methods constitutes a more severe test of the assumptions. The binary alloy system silver-gold is excellent for this purpose for several series of emf measure-

Jan 1, 1954

By S. R. Goodman, Hsun Hu

A detailed study of texture developmenf in poly crystalline copper atzd 70-30 brass has been completed. Textural changes as a function of deformation are shoum by pole jigmres and by intensity measurements oF- various rejlectiotzs from the rolling plane and the rolling direction. These examinations were accompanied by measurements of stacking fault frequency, hardness changes, and microstructure. Some of the results were briefly presented earlier. Additional results reported here are consistent with the idea that deformation faulting or slip by partial dislocations is of primary importance in the formation of deformation textures in fcc metals. lo examine the idea that deformation faulting is of primary importance in determining whether the texture is the copper type or the brass type an extensive study of the development of polycrystalline textures in copper and 70-30 brass was initiated. Besides the determination of complete pole figures, the intensities of the various reflections from both the rolling plane and the plane perpendicular to the rolling direction, the peak shifts due to deformation stacking faults, and the hardness of the rolled specimens were examined at various reductions from 10 to 99 or 99.5 pct. Mi-crostructures were examined by transmission electron microscopy. Some of the results were briefly presented in an earlier publication.' Since then, additional information has been obtained. This is given in the present paper. EXPERIMENTAL PROCEDURE Material and Specimen Preparation. The material used was a commercial electrolytic copper bar 1i in. wide and 2 in. thick and a 70-30 brass bar la in. wide and 1i in. thick. Chemical analysis indicated a purity of 99.97 pct for the copper, with 0.025 pct 0 as the major impurity. The 70-30 brass was of higher purity with 0.0016 pct 0 as the major impurity. Extreme care was taken in the preparation of the starting material to insure uniformly fine grains with a nearly random initial texture. The two bars were first cold-forged and then annealed to eliminate any original texture. The grains were then refined by several cold rolling (approx 30 pct reduction) and annealing treatments. The + -hr anneals were carried out in a salt bath at 390" to 440°C for copper and at 490°C for brass. The resulting penultimate grain size was 0.06 mm for copper and 0.03 mm for brass, and both showed very little preferred orientation. The number of prior cold rolling and annealing cycles was such that the final thickness after various final reductions of 10 to 95 (for brass) or 99 (for copper) pct was the same (0.020 in.). These annealed strips were rolled in two directions by reversing end for end between passes according to the following schedule: 0.006 in. per pass to 0.100 in., 0.003 in. per pass to 0.050 in., 0.002 in. per pass to 0.025 in., 0.001 in. per pass to 0.020 in. Texture Determination. The development of rolling textures was studied by examining complete pole figures determined from the (111) reflection. Specimens thinned from one face of the strip to half thickness (0.010 in.) were used to obtain the central portion of the pole figures, while specimens thinned from both faces to 0.003 in. were used to obtain the peripheral portion. The reflection and transmission techniques have been described previously. In addition to X-rav pole figures, texture development was also studied b; examining the intensity variation of the (Ill), (200), (2201, (311), (331), (420), and (442) reflections from the rolling plane and from the plane normal to the rolling direction, as a function of deformation. The same specimens used for the central portion of the pole figures were used for the intensity measurements of the various reflections from the rolling plane. For intensity measurements from the plane normal to the rolling direction, composite specimens were prepared by mounting sections cut parallel to the transverse direction of the strip. An epoxy resin was used to bond these sections together, and the entire composite was then mounted in a cold-setting resin to facilitate subsequent polishing and etching to remove distorted metal at the cut. The intensities were expressed in units of the integrated intensities measured from an annealed copper specimen having almost no preferred orientation. Stacking Fault Frequency Determination. Following the analysis of Warren: the stacking fault frequency, a, was determined from the change in the peak separation (A%) of two neighboring reflections of a deformed specimen, as compared with the normal peak separations of a fully annealed specimen. To obtain sufficient intensities for the second-order reflections, (222) and (400), composite specimens were prepared from parallel sections cut from the strip at 30 deg to the rolling direction for copper and 25 deg for the brass.* From texture data, these sections are known to contain a large population of both (111) and (200) planes. Since residual stresses can also cause X-ray line shifts (the direction of line shifts depends upon the sign of the stress), the use of composite specimens consisting of sectioned planes should help compensate for these effects as the residual stresses change sign from the surface to the central section of a rolled strip. Since the amount of peak shift is almost un-measurable in brass rolled 15 pct and in copper rolled

Jan 1, 1969

By R. S. Pratt

IT is proposed to discuss the materials and furnaces, as well as the melting procedures used in preparing metal for casting billets, bars or cakes for mill fabrication. As far as possible, consideration will be given to the alloys that are commonly made in most brass mills producing strip, tube, rod and wire. RAW MATERIAL The basic raw material for such mills, of course, is copper, which may be obtained in the form of ingots, ingot bars or cathodes. Refinery-cast ingots and ingot bars, which are simply double ingots, are supplied in accordance with A.S.T.M. Specifications as regular electrolytic or fire-refined tough-pitch copper. In the wrought-metal industry, the electrolytic brands have been preferred, although during the war large quantities of fire-refined coppers sufficiently pure to be suitable for all existing requirements were imported from South America. With the exception of Lake copper, most primary fire refined coppers produced in this country have not been considered satisfactory for wrought metal alloys. Cathode copper, which is now widely used instead of ingot copper for alloying, is the electrolytically deposited metal that is normally remelted in the production of electrolytic tough-pitch ingots. It is in the form of rough, flat plates not suitable for processing but quite satisfactory for melting when sheared into suitable sizes. Raw zinc is perhaps the next most important raw material and this is obtained in various grades, depending on the analytical requirements of the alloy to be made. The grades of zinc as outlined in the A.S.T.M. Specifications vary in cost with the amount of impurities-lead, iron, cadmium-and are purchased in such a way as to produce the most economical mixture consistent with the purity required in the alloy. Other virgin metals (lead, tin, aluminum and nickel) are used in varying quantities for making copper alloys. These elements can also be purchased in accordance with the appropriate A.S.T.M. Specifications where available. Also available are a number of special alloys, which are used as deoxidizers or as means of adding relatively small quantities of elements not suitable for adding directly as virgin metal. In this category are such materials as phosphor copper or phosphor tin, silicon copper, manganese copper, cadmium copper, and copper-iron or zinc-iron alloys. Some of these alloys may be purchased on a definite alloy basis or may be produced in the plant itself for its own use. For largely economic reasons, however, a great proportion of the charge to the melting furnaces consists of alloy scrap. In the production of many finished products, as much as 70 or 75 per cent of the metal originally cast may be discarded at various points along the production line. This material eventually finds its way back to the casting shop as mill scrap, overhaul or scalping chips, skeleton scrap, rod turnings, or miscellaneous fabricating scrap. One of the most serious problems in the

Jan 1, 1946

IN order that you may be expert in every phase of this art of parting, I wish to caution you upon twelve points, all necessary, so that you may know beforehand what may happen to you and what provision you must make to obtain good results. Understand that the gain derived from this art lies in carrying out the work that you wish to do accurately and with profit, which means nothing other than working with certainty and seeing that there is no loss of gold or silver [69v] or substance of anything that is valuable in itself. For, since everything lost is silver or gold, it is valuable however little. it may be, and many little things obviously make one large one; for gain increases gain, and loss, loss. Therefore, you will have as your first task to seek to have the materials that you are to use for making the aqua fortis of as perfect a nature as possible. I tell you this because the saltpeter is often weaker and of worse quality than the alum. For this reason it is necessary to make an effort to have it not only well refined and free from earthiness but also of a nature as powerful as pig [dung] saltpeter, the color of which tends strongly toward yellow. In order to work better, you also refine this again before you put it to use, as I shall tell you in its place. Likewise, see if you can get alum of the red kind that comes from the Levant or from Cartagena, for it costs less and is more powerful. Furthermore; see that you have a good number of well-formed cucurbits of properly purified glass not too large and of, equal content and size. Above all, see that they contain, no indentations, bubbles, folds, or scratches, especially, in the, body or in the bottom, because they break easily and the nature and great force of the acid pierces them by eating away, and makes a little hole. For this reason, cucurbits. are always divided into four grades; one is taken for making aqua fortis, another for drying the waters when they are laden with silver, the third for recovering the acids from the separations, and the fourth are either rejected as useless or dangerous, or are saved for recovering the whites or for some other service. Whoever wishes to practice this art well should remember to keep a large supply of cucurbits, receivers, and alembics. The third is the precaution which one must take in luting them; first, to

Jan 1, 1942

H. RIES, Ithaca, N. Y.-The part of Mr. Fiske's paper that interests me especially is that portion dealing with the raw materials, and the tests that were applied to the raw materials in order to determine their value in advance, if possible, because that, I believe, is a step in the right direction. For a number of years I have done my best to persuade different consumers of clay to develop standard methods for testing raw materials. We have in this country a large variety of clays which can be used for a great many different purposes, but in many cases the consumers either have no standard methods for determining the value of those clays in. advance, or if they have they do not publish them; consequently it often puts the clay miner at a disadvantage. If, for example, manufacturers of different types of refractory materials would state publicly just what physical tests their raw materials have to meet, it would, I believe, help them to find more easily the materials that they are looking for, and the clay producer would also be benefited. It would also encourage him to have his clays tested in advance, so that samples could be accompanied by certificates of physical tests that would be of convenience to the manufacturer. At the present time, in this country there are certain types of clay which seem to be rather scarce. There apparently are not many deposits of clay that are exactly suited for the manufacture of zinc refractories. So, too, there are not many deposits of clay that are suited for the manufacture of glass-pots, or the blocks for glass tank furnaces, or clays that can be used for graphite crucibles. Now, in many cases, no standard series of tests has been developed. I am also gratified to see that Mr. Fiske considers the tensile strength. tests of value. Some years ago the American Ceramic Society appointed a committee to draw up a series of recommendations covering standard tests. These recommendations were especially for the use of State geologists and the U., .S. Geological, Survey. Among the tests that were considered was the tensile-strength test, which Mr. Fiske has mentioned in his paper. Unfortunately, a majority of the committee turned it down, and the test was therefore not officially approved, but two of us, who formed the minority, believed in it. Since then the other members of the Committee have come to see that that is an important test to make and Mr. Fiske has emphasized it in his paper.

Jan 1, 1918

By A. J. Lena, M. F. Hawkes

Changes in hardness, tensile properties, microstructure, electrical resistance, and X-ray diffraction effects indicate that lattice strains are necessary for the embrittlement of ferritic stainless steels when heated for relatively short times at 475°C (885°F). It is suggested that 475°C (885°F) embrittlement is due to the accelerated formation of an intermediate stage in the formation of s under the influence of these strains. FERRITIC stainless steels (low carbon alloys of iron with more than 15 pct Cr) are subject to two forms of embrittlement when heated in the temperature range of 375° to 750°C. The embrittlement which occurs after long time heating between 565" and 750°C is well understood; it is caused by the precipitation of the hard, brittle s phase. Sigma is an intermetallic compound of approximate equi-atomic composition with an extended range of formation in Fe-Cr alloys. The maximum temperature at which this form of embrittlement can occur is dependent upon chromium content; and is approximately 620°C for a 17 pct Cr steel and 730°C for a 27 pct Cr steel. The other form of embrittlement occurs after relatively short heating periods in the range of 375" to 565°C; in the higher chromium steels, hours may be sufficient as compared to months for s embrittlement. This phenomenon is not at all well understood and several controversial theories have been proposed. The rate and intensity of embrittlement increase with increasing chromium content but the maximum rate occurs at 475°C re-gardless of chromium content. As a result of this, the phenomenon has been termed 475°C (885°F) embrittlement. The effect of 475°C embrittlement on the properties of ferritic stainless steels has been thoroughly reviewed by Heger.1 The embrittlement causes a pronounced decrease in room temperature impact strength and ductility, a large increase in hardness and tensile strength, and a decrease in electrical resistivity and corrosion resistance. Microstructural changes accompanying embrittlement are minor and difficult to interpret with a general grain darkening, appearance of a lamellar precipitate, grain boundary widening, and precipitation along ferrite veins having been reported at various times. With the exception of reported line broadening, X-ray diffraction studies by conventional Debye analysis of solid samples have been of little value. BY making use of electron diffraction methods, Fisher, Dulis, and Car-roll' have recently shown the existence of a chromi-um-rich, body-centered cubic phase in 27 pct Cr steels which had been aged at 482°C (900°F) for as long as four years. Two types of theories have been advanced to account for the embrittlement. The first of these requires the precipitation of a phase not inherent in the Fe-Cr system with various investigators suggesting a carbide,3 nitride,3 phosphide,4 or oxide." Theories of this type have difficulty accounting for the influence of alloying elements on the embrittlement and for the facts that a minimum chromium content is necessary for embrittlement and the intensity of embrittlement increases with increasing chromium content. The second type of theory that has been proposed relates 475°C embrittlement to s phase formation which is inherent in the Fe-Cr system. An assumption of this kind can adequately explain the influence of alloying elements, for they exert an effect on 475°C embrittlement similar to that on s phase for-mation as can be seen in Table I. The minimum chromium content is essentially the same for both phenomena and it has been shown12,13 that s is a stable phase in the embrittling temperature range. In addition, it has been reported14,15 that pure alloys embrittle to the same extent as commercial type alloys. There are, however, several factors which have prevented complete acceptance of a s phase theory. Foremost of these is that the embrittlement can be removed by reheating for short time periods above 600°C, which in the higher chromium steels is within the stable s region. No s has ever been observed after one of these curing treatments, nor has any s been found as a result of embrittlement at 475°C. In addition, the simple precipitation of s cannot explain the time-temperature relationships for reactions between 350°and 750°C. This behavior is shown schematically in Fig. 1. Newell 16 and Ried-rich and Loib4 have shown that 475°C embrittlement follows a C-type curve as illustrated, while Short-

Jan 1, 1955

By E. N. Cameron

GRAPHITE has been included in U. S. lists of strategic minerals since the problem of mineral deficiencies was revealed during World War I. Since 1918 the domestic graphite industry has led a precarious existence, and there has been much uncertainty as to the amounts of usable graphite of various grades that would be available from domestic sources in time of emergency. In 1950-1951 therefore, the writer, assisted by Paul L. Weis, undertook a review of domestic graphite sources for the U. S. Geological Survey.' The conclusions of this study are presented here, with a discussion of some technologic and politico-economic factors bearing upon the problem. Uses of Graphite: Natural graphite as marketed exhibits a wide range of properties, which determine the uses to which it is put. The most essential uses are in the manufacture of crucibles and related refractory articles, in lubricants and packing materials, and in the manufacture of batteries, foundry facings, pencils, and carbon brushes. Numerous specifications covering the mineral in its various applications must be met by producers and processors of graphite. The problem of supply is therefore not simply one of procuring a sufficient total tonnage, but the more difficult problem of procuring enough of each different grade to meet foreseeable needs. The amount of graphite required by American industry is not large. Ordinarily only a few thousand tons of strategic grades are consumed annually, yet the elimination of this small tonnage would have serious effects in several industries. Strategic Graphite: Since World War I, 60 to 100 pct of the country's annual supply of graphite has been furnished from imports. At present, natural amorphous graphite for use in pencils and batteries is produced largely from American-owned mines in Mexico. Graphite for foundry facings is obtained from a number of sources. Neither grade is a serious problem. High purity graphite for carbon brushes and for pencil leads, however, is imported, largely from Ceylon, in the form of amorphous lump graphite. Most of the flake graphite used for crucibles and related refractory articles is likewise imported, largely from Madagascar, and much of the lubricant and packing grade graphite used by industry is obtained from the same source. The strateg'ic grades of graphite are therefore amorphous lump of the Ceylon type, crucible flake, and flake suitable for lubricants and packing. Ceylon lump and Madagascar flake have for many years been accepted as standard by domestic consumers of graphite, and various essential manufacturing processes are geared to the use of graphite from these sources. Ceylon graphite as marketed is classified into several grades based on particle size and purity. Processing methods are said to be simple, but the products marketed are carefully graded and are consistent in their characteristics, an important matter to the consumer. Nearly all the graphite produced in Ceylon is from veins. Resources are reported to be large, labor is cheap, production costs are low, and world competition is slight—factors accounting for the commercial success of the graphite mining industry in Ceylon. Madagascar is reported to have deposits of the Ceylon type, but its output consists almost entirely of flake. Madagascar graphite as received in the U. S. is further processed by importing organizations, and a large number of grades are produced to meet industry requirements, especially those for crucible flake and for lubricant and packing grade flake. Madagascar crucible flake as marketed is noted for coarseness, uniformity, toughness, clean-

Jan 1, 1957

By Frederick F. Frick

SPONGE iron as produced at Anaconda is a fine, -35 mesh, impure product, about 50 pct metallic iron, obtained from the reduction of iron calcine at a temperature of 1850°F by use of coke resulting from slack coal. The metallic iron particles are bulky and spongey and precipitate copper readily and rapidly from a copper sulphate solution. Investigation of the treatment of Greater Butte Project, Kelley, ore at Anaconda early showed the desirability of using sponge iron as a precipitant for the copper in solution resulting from desliming of the ore in a dilute sulphuric acid solution. Anaconda had done considerable work on the production of sponge iron in 1914 for use as a precipitant of copper from leach solutions. Some success and considerable experilence were attained at the time. indicating that, sponge iron might be successfully made by a modification of the process used in 1914, a batch process in which an iron calcine was reduced by means of soft coke, resulting from noncoking coal, in a Bruckner-type revolving horizontal cylindrical furnace widely used 50 years ago. The coke and calcide formed the bed in the Bruckner furnace, which was rotated at about 1 rpm. The bed was brought to a temperature of about 1800°F by means of an oil flame over the surface. Although results were reasonably satisfactory, they did not warrant full development of the process at that time. A good deal of work has been done in the last 50 years on the production of sponge iron. The objective in some cases has been the production of a precipitant for copper from solution, but the bulk of the work has been done for the production of open-hearth steel furnace stock. The production of an open-hearth stock presents two problems rather than one: first, producticon of the sponge iron, and second, what is perhaps of equal difficulty and importance, conversion of the sponge iron into a form suitable for use in the open-hearth furnace. So far as is known to the writer, none of the sponge iron processes tried in the past have proved to be economically feasible. However, Anaconda had a combination of conditions appearing to justify an attempt to produce sponge iron which would serve for the leach-precipitation-float process. It was thought that the process used in 1914, if changed to a continuous one, might work out satisfactorily. The following favorable conditions at Anaconda justified the investigation: 1—A sufficient tonnage of good grade iron calcine resulting from the roasting of a pyrite concentrate in one of the acid plants, at substantially no cost. 2—Reasonably cheap natural gas. 3-—The fact that there was no need for production of a high grade product. 4— The fact that there was no need for obtaining a consistently high reduction of' the iron in calcine. A small revolving Bruckner-type furnace about 2 ft ID by 4 ft long was set up for early pilot work at the research building. This pilot furnace showed that a satisfactory product could be obtained at reasonable cost. It also indicated a marked advantage in preceding the reduction furnace with a furnace of similar size and capacity for preheating and roasting out any residual sulphur from the feed. The small furnace was operated for several months, various details of the process were worked out. and sponge iron was produced to supply a pilot LPF plant which treated 300 lb of Kelley ore pel- hr. Later a second pilot furnace 5 ft in diam and 12 ft long inside was set up at our reverberatory furnace building. This furnace confirmed the data of the small furnace and gave a basis for design of the final plant. At Anaconda a pyrite concentrate, running about 48 pct S, is recovered from copper concentrator tailings by flotation. This concentrate is roasted to sulphur of 3 pct or less at the Chamber acid plant. The iron calcine contains about 57 pct Fe and 18 pct insoluble. The iron calcine feed, as mentioned before, is re-roasted and preheated in a reroast furnace preceding the reduction furnace. Both are of the Bruckner type. The reroasted calcine is fed into the reduction furnace at 800" to 1000°F along with 30 pct slack coal. In the feed end of the furnace the volatile is burned from the slack, giving a soft coke which readily serves for reduction of the iron. Hard metallurgical coke will not serve the purpose. since it does not reduce CO readily at a temperature of 1850°F. All indications are that the actual reduction of the iron is accomplished by carbon monoxide below the surface of the bed, which is 30 in. deep at its center. Apparently there is a constant interchange: Fe²O³ + 3CO = 2Fe - 3CO², CO² + C = 2CO Actually iron oxide is reduced by CO at somewhat lower temperature than the 1850 °F used in the process. but this temperature is necessary to obtain a satisfactory rate of furnace production. The furnace atmosphere is generally reducing, and typical blue carbon monoxide flames satisfactorily cover the bed. Gas flames from four 3-in. Denver Fire Clay Inspirator burners are played directly on the bed, which is slowly cascaded by the 1 rpm of the furnace. An excess of coke is necessary to assure maintenance of good reducing conditions in the furnace bed. Part of this coke is recovered for re-use.

Jan 1, 1954

By R.K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By R. K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By F. E. Jaumot, A. Sawatzky

IT as long been recognized that there is a need for accurate systematic data on diffusion in solids. Originally, such data were needed to check existing theories but, more recently, it would appear that it could be used most advantageously as a guide to, or a check for, much needed extensions of the theory of diffusion. The awareness of the conditions which are important to experimental accuracy, the availability of the materials for accurate experiments, and the techniques have improved to the extent that it would now seem to an experimentalist that, unless extensions of the theory are made which take into account the fundamental parameters of the atoms, the electrons, and the lattice in some detail, the field of diffusion will rapidly become an empirical or semi-empirical field. The present series of experiments was designed to provide accurate data on the diffusion of the elements of the IB and IIB subgroups in silver; that is, to provide data on the diffusion in silver of three face-centered-cubic elements with roughly similar chemical properties, but with different atomic or ionic sizes and, similarly, for three noncubic elements. The elements of these two subgroups have different valences, so that the data will not give any significant information on differences due to the crystal structure of the solute. The present paper reports data on the diffusion of copper and mercury in single crystals of silver; the data for the other elements of the IB and IIB subgroups were reported previously by the authors1'2 and by Tomizuka and Slifkin.8 Experiment The general technique used was identical to that previously described1,2 and will not be repeated here. In all cases, the sectioning technique and high specific activity isotopes" were used. The short half-life of Cu64 made decay corrections more important than for the other isotopes, and necessitated around the clock shifts while data were being taken. Each section was counted at least twice (as was true for all longer half-life isotopes) and a monitor was counted along with each sample. Data for the diffusion of mercury in silver are presented at a greater number of temperatures than for the other solutes. This is a result of two circumstances. First, six (of 30) samples had to be discarded because of pitting or recrystallization which occurred during the diffusion runs, even though the samples had sustained high temperature prediffusion anneals. Either of these was a very rare phenomenon in the other experiments, and their occurrence in this case is considered in more detail below. Second, the curves of the logarithm of the activity of the sections vs the square of the penetration deptht were, in general, quite good, but frequently seemed to show one point to have high activity and the next point to have slightly low activity in terms of the best straight line. When this occurred, there was remarkable regularity of the high-low sequence. In any event, the results, as far as diffusion coefficients are concerned, were not affected by this amalgam effect. In fact, the mercury data had the highest internal consistency of any of the data. Results Diffusion of Copper in Silver—-Diffusion runs were made at eight temperatures In the temperature range from 700° to 950°C, for times ranging from 5 to 45 hr. A linear curve of the logarithm or the activity vs the square of the penetration depth was obtained for all samples. Table I summarizes the results for individual samples and Fig. 1 gives a plot 02 the logarithm of the diffusion coefficients as

Jan 1, 1958

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By P. Somasundaran, D. W. Fuerstenau

The length of the collector is found to influence the flotation of the mineral even at incipient conditions, which are below the concentration at which interaction at the solid-liquid interface begins to take place to form hemi-micelles. To study this dependence, concentration for incipient flotation of quartz was determined as a function of pH with collectors of various chain lengths. The observed effect of chain length on flotation is ascribed to that of collector adsorbed on the bubble surface. In previous studies, it was shown that at low concentrations the alkyl collector ions adsorb at the solid-liquid interface as individuals.''2 At higher concentrations, the collector ions adsorbed at the solid-liquid interface associate with each other to form two-dimensional aggregates called hemi-micelles. Above the hemi-micelle concentration, the length of the hydrocarbon chain is extremely important since the hydrocarbons are in effect removed from water during the association, making the energetic conditions more favorable for adsorption at the interface. Because of this enhanced adsorption, one observes a very rapid increase in flotation associated with the hemi-micelle formation at the solid-liquid interface. However, a dependence of flotation on the chain length at concentrations below that required for hemi-micelle association was also observed,' and this cannot be explained by the above mechanism which postulated hydrocarbon chain interactions only at the solid-liquid interface. This prompted an investigation into other possible reactions of the hydrocarbon chains and an examination of the conditions at the bubble surface involved in the flotation system and how these observations might explain the reactions at the solid-gas interface which cause the particle-bubble attachment required for flotation. To obtain more information on chain length effects, flotation, under incipient conditions, was tested by vacuum flotation techniques. The collector-concen-tration-pH relationships for flotation of quartz with alkyl ammonium acetate collectors was delineated by observing the pH at which quartz particles begin to float to the liquid surface. By investigating flotation as a function of pH, it was also possible to study the effect of neutral molecules on incipient flotation conditions, since the aminium ions hydrolyze to amine molecules at higher pH values. EXPERIMENTAL WORK Brazilian quartz specimens were crushed and sized, and the 270 x 400 mesh fraction was used for flotation studies. The samples were leached with concentrated hydrochloric acid until no coloration of the acid occurred. The leached material was washed free of chloride ions and stored in distilled water. The vacuum flotation technique developed by Schuhmann and prakash3 was used to determine the critical pH-concentration curves. This method, which can be used to delineate conditions for incipient flotation, is fairly simple and rapid. About 0.5 gm of 270 x 400 mesh quartz was placed in a 100 ml graduated cylinder which was then filled to the 100 ml mark with the collector solution made from high-purity alkyl ammonium acetate salts. The water used for the test was conductivity water saturated with air that had been passed through a cleansing train consisting of Drierite, Ascarite, a water wash bottle, and a trap. After the pH was adjusted, the cylinder was then conditioned for thirty minutes. In the tests where an acid pH was desired, sufficient acid was added before the collector solution to avoid any effect due to slow desorption of collector from the quartz surface. After conditioning, vacuum was applied to the system and the flotation or nonflotation of the quartz was noted. The pH at which the quartz particles began to float to the liquid-gas interface was taken as the critical PH. Critical pH curves were thus determined for different concentrations of the various collectors. Hallimond tube flotation data were taken from the authors' previous publication1 for correlation with that from the vacuum flotation. RESULTS AND DISCUSSION The results of vacuum flotation studies for determining critical pH-concentration curves, i.e., curves which delineate conditions for incipient flotation, are shown in Fig. I. In generaI, all the curves exhibit an upper and lower pH limit between which flotation will

Jan 1, 1969

By Leendert de Witte

Conventional resistivity logs consisting of a short normal, a long normal, and one or more long lateral curves do not give data that allow a complete quantitative interpretation in beds thinner than 20 ft. Reservoir rocks usually exhibit zones of continuous homogeneity of quite limited thickness where the long lateral curves become useless because of adjacent bed effects and boundary phenomena. If the beds are 12 ft or thicker, the short and long normals may be used for qualitative interpretation, which can be streamlined by the application of simplified departure curves. For beds of a thickness less than twice the long normal spacing, this procedure breaks down. The combination of the limestone curve, the later-olog or guard electrode log, and the microlaterolog permit quantitative interpretation for beds that are at least 10 ft thick, provided the mud resistivity and the hole diameter are known with sufficient accuracy. For beds thinner than 10 ft, combinations of the microlaterolog with short spaced laterologs and pseudo laterologs appear to be promising. Interpretation of these curves again requires the application of simplified departure curves. Resolution of various possible combinations was analyzed using departure curve data calculated on the Whirlwind I computer at the Massachusetts Institute of Technology. A field example is shown using the microlaterolog-microlog combination, and the combination of a 6-in. modified laterolog plus a 6-in. pseudo laterolog. INTRODUCTION For the purpose of quantitative interpretation of resistivity logs in porous formations, we want to obtain two essential quantities from the logs, namely, the true resistivity of the undisturbed formation, Rt, and the resistivity of the part of the formation invaded by mud filtrate, Rt. The apparent resistivities of all conventional logging devices are functions of these two parameters and are also influenced by a third unknown parameter, the diameter of the invaded zone, d. It has been shown' that from the normal curves alone it is impossible to arrive at a unique solution for the three unknowns, Rt, R1, and d1. In very thick homogeneous beds, if invasion is not too deep, we can obtain a fair approximation to Rt from the long lateral curves and then use the two normal curves to find Rt and d1 Even under the most favorable conditions, the resolution of this system is not very good. The short normal does not give a reasonable approximation to R1 unless invasion is very deep (dl>16 hole diameters). For very deep invasion, however, the long laterals no longer approximate Rt. For bed thickness between 20 and 40 ft, the long laterals are affected appreciably by the adjacent beds; and the curves are distorted by boundary anomalies to the extent that they lose their quantitative usefulness in most cases. For the same bed thicknesses, the normal curves still function reasonably well. Although it is impossible to find unique solutions Lor R1 and Rt using the normal curves alone, we can obtain a reasonable approximation for the ratio R1/Rt through the use of simplified departure curves. This fact was brought to our attention by A. J. de Witte, geologist with Continental Oil Co. As the magnitude of Rl/Rt is a major clue to the presence of oil in formations, this method can be used to good advantage for qualitative analysis and will be discussed in somewhat greater detail. With the aid of suitable bed thickness corrections, the analysis of the normal curves may be used for bed thicknesses larger than 12 ft. For thinner beds, the method rapidly loses its resolution; and we have to resort to different types of resistivity logs if we want to attempt to analyze the curves quantitatively. The inadequacy of conventional resistivity curves in thin beds is far more serious than generally realized. Fig. 1 shows a conventional E. S. with a 16-in. and 64-in. normal and a 16-ft lateral through a section of Lansing-Kansas City lime, in comparison to a guard electrode survey through the same section in a neighboring well. The porous zones, which show up as low resistivity breaks on the guard electrode log, are completely masked by adjacent bed effects and boundary anomalies on the conventional curves. Even the short normal shows most of the porous Zones only as Vague deflections and in many cases fails to register Their

Jan 1, 1955

By J Price, M. R. Geer, H. F. Yancey

COAL mine operators recognize coal as an abrasive material, because the wear of drilling, cutting, and conveying equipment is reflected as a cost item for replacement of parts. Similarly, industrial consumers of coal experience abrasive wear on all coal-handling equipment. Operators of pulverized fuel plants are doubtless most keenly aware of the abrasiveness of coal, because under the high contact pressures developed between coal and metal in pulverizers, abrasive wear is increased many fold. Moreover, experience in operating pulverized fuel plants has demonstrated that some coals are much more abrasive than others. Hardgrove' stated that maintenance costs entailed by the wear of grinding elements is often a more important variable than the cost of the power required to pulverize different coals. Craig2 also reports that one coal may cause pulverizer parts to wear several times faster than another. It is apparent, therefore, that those concerned with pulverizing coal could profitably employ a method for estimating the abrasiveness of different coals, just as they utilize standard tests for thermal value, grindability, and ash-fusion temperature to assist in selecting the most suitable and economical coal to use in a particular plant. The objective of this investigation was to develop a test procedure that would be suitable for general use in estimating the abrasiveness of coals. However, few, if any, of the standard tests now used for evaluating the properties of coal are the product of a single investigation or the result of a single investigator's efforts. Rather, in each case, a testing procedure was devised by one investigator, used by others on a wider variety of coals, and finally refined completely as the result of the joint efforts of a number of interested people. Thus, the test procedure for estimating abrasiveness developed in the course of this work may not be refined sufficiently in its present form for general use, but it may serve as the starting point from which an acceptable test procedure can be developed. The method has been used thus far on only about a dozen coals, and there has been no opportunity to attempt a correlation between experimental results and actual plant experience. Only wider use of the procedure by other investigators and correlation with plant experience can determine to what extent the method will have to be modified to render it suitable for general application. Test Method Although the literature contains no record of an attempt to devise a method for estimating the abrasiveness of coal that could be used industrially, several investigators have tested properties of coal that are closely related to its abrasiveness. The abrasiveness of a material generally is considered to be related to its hardness, and hardness tests for coal have been employed by Heywood,' O'Neill," and Mathes. Also, the resistance of coal to abrasion, a property that presumably is related to the abrasiveness of coal, was measured by Heywooda and by Simek, Pulkrabek, and Coufalik.2 11 these investigators tested only individual pieces of coal. Since coal is a heterogeneous material having components of varying properties, tests of this type can yield results having little more than academic interest. Only a test method that utilizes a representative sample of coal can give results that are useful industrially. The abrasion tests used for various other materials have been considered for adaptation to testing the abrasiveness of coal. The tests used for metals,7-9 paving and flooring,'" and rubber," cannot be used because coal is not sufficiently abrasive.~ The present experimental work was begun before World War II and was conducted by three research fellows"'" working under a joint agreement between the University of Washington and the Bureau of Mines. After a great deal of preliminary work with a variety of apparatus and materials, a test procedure was developed which consisted of rotating a test disk 2Yz in. diam in a steel mortar containing the coal sample. The shaft carrying the test disk at the lower end and a 100-lb load on the upper end was free to move vertically. The bed of coal in the mortar was kept fluid by low-pressure air admitted through a port near the bottom of the mortar. Measurable wear on an Armco iron disk could be obtained in this test procedure, but, despite extensive efforts to eliminate them, several major disadvantages remained in this test method. First, with most coals the amount of wear on the iron disk did not exceed a few milligrams. Second, a single type of disk was not applicable for all coals. A smooth iron disk gave satisfactory results with both bituminous and sub-bituminous coals, but hardly any wear with anthracite or coke. A disk having studs or projections gave more satisfactory abrasion losses with anthracite and coke and presented no operating difficulties with free-burning bituminous and sub-bituminous coals. It could not, however, be used with caking coals because these coals formed a

Jan 1, 1952

By R. H. Merrill, D. W. Wisecarver

The paper "Design of Surface and Near-Surface Construction in Rock" by Deere, Hendron, Jr., Patton, and Cording discloses a principal difference between civil and mining engineering as applied to openings in rock. Generally, the civil engineer considers an opening as an asset, where a mining engineer finds that most of his openings are a liability. The openings, or rock surfaces, treated in the paper by Deere and coauthors are designed for lasting stability and the foundations for dams, the diversion tunnels, abutments, and surface excavations are expected to be stable for long periods or provide continuous access and other useful purposes. Except for those openings used for the transportation of men, materials, ore, and for ventilation, the mining engineer finds that his underground openings serve no useful purpose once the mineralized rock has been removed. Usually, these openings create problems such as reduced ventilation efficiency, added requirements for scaling, sealing, and other tasks necessary to maintain or isolate the openings. The surface openings and mine plants present another liability to the mining engineer. After the product has been removed from the earth, the abandoned pits or strips, tailing ponds, dumps, and buildings sometimes become hazardous, unsightly, or occupy surface areas that could be used for other purposes. As a general rule, the various disciplines involved in rock mechanics have different objectives and uses for openings; however, the basic concepts regarding the design or control of openings in rock are similar for each discipline. The review by Deere and his coauthors contains examples of the duplications in this technology, and, in particular, the common approaches used by civil and mining engineers. Therefore, both the review paper and this report consider the problems that are common to most of

Jan 1, 1967

By J. W. Sandelin, L. S. Birks

The group five metals, vanadium, niobium, and tantalum all show cold-rolled textures of {100)(011) and {112)(0ll) with a preference for the (100) in vanadium and niobium and for the {112) in tantalum. Recrys-tallization texture of (100) and (111) was reported1 for vanadium after annealing (no temperature stated). For tantal~m ,~ annealing below 1200°C strengthened the (112) texture but the (111) texture increased and was predominant as the annealing temperature was raised to 2500°C. Annealing niobium up to 1100°C strengthened the ( 100) texture and developed a weak (111) texture.' In the present work niobium has been annealed up to 2000°C. Nearly 70 pct of the grains showed {111) texture with only a weak (112) component and an insignificant (100) component remaining. In addition, double-crystal rocking curves were used to follow the increase in crystal perfection of the grains with increased annealing time. Material and Treatment. Samples i by 4 in. were sawed from & -in.-thick cold-rolled niobium sheet obtained from Wah Chang. Chemical analysis of the material showed it to be 99.4 pct pure with tantalum as the major impurity. Individual pieces were annealed for 2, 15, 30, and 60 rnin in a vacuum of 10'* Torr using an rf generator. They were etched until the grain boundaries were well-defined, Fig. 1. Average grain size varied from 1 mm for 2 min annealing to 2 mm for 60 rnin annealing. Experimental Results. Preferred Orientation. The orientations of 97 of the 117 grains in the specimens of Fig. 1 were determined by back-reflect ion Laue patterns. A General Electric 10-cm-diam cylindrical camera was used rather than the conventional flat camera in order to record more of the low-index spots. The method proposed by Forest, Barton, and schieltz4 was used to transform the cylindrical film patterns to standard stereographic projections. Table I gives the compilation of data. Even 2 rnin anneal at 2000°C is sufficient to yield a strong (111) preferred orientation, and the percentage of grains with this orientation increases steadily with annealing time at the expense of all other orientations. Crystal Perfection. X-ray topographs were taken of each specimen in both the (111) and (112) orientation using the method described by Birks and Grant.' As the anneal time increases, the grains become larger and the individual reflections become slightly more uniform in intensity, indicating an increase in crystal perfection. For a more quantitative measure of crystal perfection, it was necessary to measure the double-crystal rocking curve. The spectrometer employed was a Gaertner instrument of Compton design. LiF was chosen for the first crystal because the (400) reflection with d spacing of 1.05 AU is a good match to the (222) niobium reflection with d spacing of 0.95 AU. CuKp radiation was used in order to further reduce the d spacing mixmatch correction.' A variable aperture was placed between the LiF and the niobium specimen so that a single grain or even a small portion of a grain could be examined. Fig. 2 shows typical rocking curves for the four annealing times. For the 2-min specimen, a single peak is observed with 10' of arc full-breadth at half maximum. As the annealing time is increased to 15 or 30 min, several sharper peaks of 40 to 80" breadth can be seen within a single grain. After 60 rnin anneal only a single peak of about 30" is observed. Table I1 shows the corrected rocking curve breadths and the dislocation densities, ND. The latter were calculated from the equation7 where W is the corrected rocking curve breadth at half maximum in radians and b is the effective Burger's vector. For (110)(111) slip in niobium, b is 2.86 AU. Discussion. The annealing of cold-rolled niobium at 2000°C causes rapid preferential growth of grains with {ill} orientation. After only 2 rnin annealing time, 35 pct of the grains have the (111) orientation, and after

Jan 1, 1968

By H. Papazian, Robert A. Lad

SINCE it can be shown both theoretically'' : and experimentally that disordered Cu3Au has a greater internal energy than the ordered alloy, it might be expected that its chemical reactivity would be greater. Experiments were initiated' to test this hypothesis. This note will describe some recent results obtained in the study of the rates of corrosion of ordered and disordered polycrystalline Cu3Au by aqueous FeCl., The work of Robertson' has indicated that the attack by such solutions is intergran-ular and highly orientation dependent. It was of interest to see whether the order-disorder effect was great enough to overcome the variations from specimen to specimen which would arise from this type of attack. The polycrystalline alloy specimens (0.020 in. wire, 1¾ in. long) were preannealed in ½ atm H, at 700°C for 2 hr. The subsequent heat treatments to produce order and disorder were performed in M atm He. Disordered specimens were obtained by heating at 450°C for 2 hr and quenching in water. Ordered specimens were produced by heating for 2 hr at 450°, furnace cooling to 380°, and soaking at 380°C for 80 to 90 hr. Room temperature was reached by cooling to 150" at a rate never exceeding 7" per hr, and water quenching from 150°C. The specimens so produced exhibited electrical resistivities characteristic of the two states; of the order of 11.27x10 ohm-cm for the disordered, and 4.28x10 ohm-cm for the ordered specimens. The corrosion rates were studied at 30°C in ferric chloride solutions of several concentrations (?,¼, 1.5, and 1 molar). The specimens were attached to a stirrer during the tests. Tests were interrupted at intervals, and the specimen weight change was determined after washing and drying. Analysis of the solutions showed that the attack was limited to the copper. The higher corrosion rate for the disordered alloy, as illustrated in Fig. l, is typical of the results obtained. The effect of variation in ferric chloride concentrations is indicated in Table I for typical specimens. The variations in the ratio of reactivity for disordered and ordered specimens at the different concentrations are within experimental error, and the best value is estimated to be near 1.4. The experimental variation was due in part to the mode of attack, as mentioned, and in part to the fact that films were formed on the specimens under some conditions. Electron diffraction patterns of the films were very complex and indicated the presence of metallic iron, as did chemical analysis. In an attempt to eliminate the difficulties arising from the mechanism of attack, single crystal specimens were used. A greater reaction rate was again measured for the disordered specimens, but the reproduci-bility was no better than that for the polycrystalline metal. This would indicate that film formation was primarily responsible. It was concluded that the reaction with aqueous ferric chloride served to demonstrate that the reactivity of disordered Cu3Au is greater than that of the ordered alloy. However, the difficulties with film formation did not permit determinations of a precision great enough to warrant extension of the study to partially ordered alloy systems.

Jan 1, 1957