Search Documents

By H. L. Hartman

The drop tester has proved an invaluable tool for the investigation of percussion drilling in the laboratory in "slow motion". It has allowed the process of rock penetration by impact to be studied a single blow at a time. In the present work, the relation of cratering to indexing has been determined under conditions simulating those in the bottom of the hole at atmospheric pressure. Indexed blows form craters which are influenced by others adjacent to them. Two unique effects are involved: (1) the provision of additional free faces in proximity to the point of impact and (2) the creation of subsurface damage by the previous blow(s). Both have a pronounced influence on the volume of rock removed per blow, which governs the rate of penetration in actual drilling. The emphasis in this study was placed on determining effects of index distance and impact energy on crater volume when blows were struck on a previorusly "drilled" or damaged surface, a situation most representative of down-hole conditions. The results indicated that (I) the optimum index distance on a damaged surface is greater than on a fresh, undamaged rock surface; (2) the volume of rock broken at optimum index distance is about the same for both surface conditions with die-shaped chisels but tends to be greater on a cratered surface with wedges; (3) the optimum index distance and maximum crater volume are proportional to the energy level; (4) at a given energy level, the volume of rock broken by dies generally exceeds that by wedges; and (5) maximum crater volume varies, approximately, inversely with width of die but is nearly independent of included angle of wedge. INTRODUCTION This is the third of a series l,2 of papers reporting on one phase of a continuing program of drilling research being conducted in the Rock Mechanics Laboratory at The Pennsylvania State U. The phase under consideration is crater geometry — blow energy relations in percussion drilling. While the previous papers have discussed mainly craters produced by single blows, indexed-blow studies are the subject of this paper. The basic mechanism of drilling under study here — that of penetration of a chisel-shaped bit subjected to impact — is the one employed in probably 90 per cent of all rock drilling in mining, percussion drilling. It also forms the fundamental action in nearly all oil well drilling with the so-called rotary (roller-bit) method. Here, the action is more complex, however, and may in actuality comprise rotary-percussion drilling. Certainly, the down-hole air and mud hammer drills, which superimpose percussion on rotation, belong in this latter category. In any event, impact blows constitute one of the principal mechanisms in the vast majority of drilling, mining or petroleum, and it is essential in drilling research to study percussion in all its basic aspects. Percussion drilling can be simulated in the laboratory by means of an impact drop tester. Striking one blow at a time with chisel-shaped bits, the drop tester permits study of most of the parameters in the drilling process except blow frequency and the interrelationship of certain variables. Single-blow craters, the simplest to produce, allow the determination of basic relationships, such as volume vs blow energy; while indexed craters most closely resemble the action in real drilling and provide data for the establishment of optimum operating criteria. Indexed-blow craters are those which are influenced by others in proximity. The simplest case to visualize, and the one studied in detail here, is that in which a given crater is formed adjacent and parallel to a previous crater, such that the second crater breaks into the first. A more complex situation usually exists downhole, where indexing is achieved by rotation of a radial-winged or rolling-cutter bit. But, admittedly, the phenomenon of indexing is more likely to be understood eventually if it is first studied in its simplest form, that related to parallel craters. Limited research has been conducted on indexed blows. The most complete study was that by Simon, 3,4 who proposed universal indexing curves to relate the important variables. His work, however, was conducted entirely with rows of craters formed on a

By Wayne D. Gould

Cities Service Co.'s Pinto Valley concentrator was designed to eliminate excess capital costs without loss of efficiency. The result is a workable plant with some important innovations. These innovations, the equipment used, and plant processes are outlined. Particular attention is paid to the work efficiency and wear of the six ball mills, the largest wet ball mills made. For experiment purposes, four designs of liners were installed. The effectiveness of each design is discussed.

Jan 1, 1977

By P. S. Kotva

Dislocation substructures in superalloy matrices of varyzng co)npositions have been studied. In general, it has been found that the alloys can be classified into ''high", ''medium", and "low" stacking fault energy classes based on the type of dislocation substructure observed in the matrix and that the substructure can be correlated to the stacking fault energy. The effect of different types of dislocation substructure and dislocation reactions on the intragranulur precipitation of carbide phases has been studied. In a Ni-Cv-Mo-Fe matrix, precipitation of MC carbides in association with stacking faults has been observed. In most superalloys, solid-solution strengthening and precipitation hardening are the chief mechanisms employed to achieve strength. The latter contribution to strength is usually achieved by the precipitation of / in certain wrought alloys. Insufficient attention has been given to the problem of obtaining strength in su-peralloys by controlling precipitation of carbides on imperfections within the matrix. The present work was undertaken to investigate the dislocation substructure in various superalloy matrices, to study the effect of such substructure on subsequent precipitation of carbides in the matrix, and to investigate whether certain modes of precipitation of carbide phases found in austenitic stainless steels2"4'6 would occur in nickel-base alloy matrices with dislocation substructures of the same type as those found in austenitic steels. 1) EXPERIMENTAL TECHNIQUES Five-pound heats of the various alloy compositions reported here were vacuum-cast. The ingots were given light deformation by rolling to break up the as-cast structure and then homogenized for 24 hr. HASTELLOY alloy X (nominal composition: Ni-2OCr-17Fe-8Mo-0.05C) was homogenized at 2150°F and In-cone1 625 (nominal composition: Ni-20Cr-5Fe-8Mo-3.5Cb-0.05C) was homogenized at 2280°F. Fabrication of 0.004-in. sheet was achieved by cold rolling with intermediate annealing treatments being carried out at the same temperature as those used for homogeniza-tion. Each solution anneal was followed by quenching. The aim of this procedure was to redissolve as much of the primary carbide phase as possible. Samples of the 0.004-in. sheet were cut and encapsulated in quartz capsules and then heat-treated in the tube furnaces. Thin foils were prepared using an ethanol-10 pct perchloric acid bath at 32°F and at a voltage of 22 v. A "window" technique was employed. Observations were made on a JEM-7 electron microscope operating at 100 kv. 2) EXPERIMENTAL RESULTS a) Types of Dislocation Substructure. Fig. 1 shows a schematic correlation between stacking fault energy, SFE, and the type of dislocation substructure observed in various matrices of nickel- and cobalt-base alloys. A precise quantitative determination of stacking fault energy is not implied in the figure but the correlation between stacking fault energy and the type of dislocation substructure obtained allows alloys to be divided into three classes in analogy with the classification employed by Swann and ~uttin~' for binary alloys of copper. Class I alloys are associated with a "high" SFE and show a cellular substructure of dislocations as typified by the micrograph of a thin foil of pure nickel deformed 4 pct at room temperature in Fig. 2. With decreasing SFE the tendency toward cell formation is lessened and dislocations tend to be arranged in coplanar groupings. Examples of this class of alloys with "medium" SFE are provided by the mi-crostructure of solution-heat-treated, quenched, and deformed thin foils of HASTELLOY alloy X, "Waspaloy" (prior to any aging), and Inconel 625. Fig. 3 shows a thin-foil micrograph of an alloy of Inconel 625 composition, solution-heat-treated, quenched, and deformed 5 pct at room temperatures. No evidence of any cell structure can be obtained in materials of "medium" stacking fault energy, Fig. 3, even after severe deformation. The stacking fault energy of the alloy shown in Fig. 3 is, however, not low enough to make the dissociation of dislocations visually obvious. As stacking fault energy decreases further, with successive addition of solute in the matrix, there is an increased tendency toward dissociation of dislocations and cross slip becomes progressively more difficult. Eventually, when the stacking fault energy is "low" enough, complete dissociation of dislocations is seen to occur as shown in Figs.

Jan 1, 1969

By Phillip E. Butler

The Pennsylvania Dept. of Transportation is actively engaged in the utilization of coal mine refuse in the construction of highway embankments. Long-held objections for utilization are invalidated by research, laboratory data, and construction performance. Laboratory, engineering, construction, and environmental impact analyses are presented from the construction of the Cross Valley Expressway embankment at Forty Fort, Luzerne County, Pa. Comparisons of laboratory data and construction measurements are given. The refuse embankment is the first of its size in Pennsylvania, and possibly the U. S., covering 1.5 million cu yd.

Jan 1, 1977

By Fred W. Gordon

The heading of this paper was prompted by the knowledge that experience, up to this time, seemed to indicate that smaller furnaces were preferable for smelting the material of this section. Since the reasonable success thus far achieved by the first furnace of this plant tends to change the above opinion, and unsettle the generally-accepted views of furnace-men as to "weak " coke, a few words as to the design of the plant and the mode of operation adopted may prove interesting.

Jan 1, 1889

By K. N. Clark, N. B. Carter, C. G. Thomas, V 7. 0 / 300 dpi

A statistically designed, experimental study showed how gangue minerals, flux additions, fineness of grind, firing temperature, and time affect the properties of acid pellets made from a Western Australian hematite ore. Alumina has less effect than silica and lime, but interactions between the six variables occur, which influence abrasion index, reducibility, and cold compression strength. Finer grinding has little influence on reducibility but improves the other two properties. The major variable is firing temperature, which interacts with all other variables to affect pellet properties. Calculations based on the data show the implications for straight-grate pellet plants and optimum hood temperature ranges.

Jan 1, 1982

By Adrian Brown

Over the last decade, a number of large slopes have been excavated in rock which contains families of joints or faults which dip steeply into the cut slope. Despite the absence of "adverse" structures, these slopes have exhibited alarming movement rates at very modest heights (as little as 100 meters) and slope angles (as little as 20º). Classical stability analysis suggests that such slopes should be unconditionally stable. This paper describes the toppling mechanism which has been found to be the cause of the observed movements and develops a general method for analysis of it. Simple cases are analyzed in order to provide charts which allow quick evaluation of the likelihood of this phenomenon occurring. The safety implications of such movements in slopes are also examined.

Jan 1, 1982

By George Simkovich

It was hypothesized that solid-state point defects should alter the flotation properties of solids. Tests conducted on pure AgCl and AgCl doped with CdC12 show that atomic point defects exhibit an important role in the floatability of AgC1. Tests conducted on PbS doped with Ag2s or Bi2S3, also show that the defect structures resulting from these dope additions, i.e., a combination of electronic and atomic point defects, contribute significantly to the flotation of PbS. IT has been established that flotation occurs only when a finite contact angle exists between a solid and a gaseous bubble.' This angle, measured through the liquid phase, is expressed by the equation where the are inter facial free energies and the subscripts S, G, and L represent solid, gas, and liquid phases, respectively. As is seen in Eq. [I] three interface free energies, sG, sl, and GL, enter into the contact angle equation. Therefore, any variation in these energies which sufficiently varies the contact angle will, in turn, vary flotation processes. Changes made in any of the phases concerned, i.e., gas, liquid, or solid phase, are reflected through the changes occurring in two of the surface energy terms. Thus, a change in the liquid composition would be noted in sL and GL, and it is this phase, the liquid, which is most frequently altered in flotation studies., Changes in the solid phase must be reflected through the changes occurring in the sG and sL terms. In particular, it is hypothesized that changes in the surface concentrations of point defects in the solid-phase will alter the sG and sL terms which, in turn, will be reflected by flotation results. As an illustration of this hypothesis one may consider the defect structure and the flotation of AgC1. The bulk defect structure of AgCl is essentially one involving equal number of cation vacancies and interstitial cations.3 Upon adding CdC1, to AgC1, a greater number of silver ion vacancies are created in the bulk of the crystal.4 On the surface of the crystal the smaller binding forces and the free space accomodations may also allow for the creation of "surface interstitial anions", which will be designated as ad-anions. Thus, the point defect structure of the surface of AgCl doped with CdCl, will consist of cation vacancies and/or adanions. If the molecular forces responsible for the surface energies, ?SG and ?sL, are significantly altered by the presence of these surface point defects, then differences in flotation results will be noted as the concentration of these defects is varied. The defects present in AgCl are predominantly atomic in nature. In the case of PbS both electronic and atomic defects are present.5 This compound conducts electrically by either electrons or electron holes depending upon whether excess lead or excess sulfur is present. Upon disolving BiS3 in stoichio-metric PbS, one increases the concentration of cation vacancies and the number of electron carriers in the bulk of the crystal.5" At the surface, the possibility of ad-anions must also be considered. Conversely, upon dissolving AgS in stoichiometric PbS one increases the concentration of interstitial cations and the number of electronhole carriers in the bulk of the crystal.5,6' At the surface the interstitial cations will be designated as ad-cations. Thus, the point defect structure of the surface of a PbS crystal doped with Bi2S3 will consist of a number of cation vacancies and/or ad-anions and an excess of electrons. Conversely the point defects on the surface of a PbS crystal doped with Ag2S will consist of a number of ad-cations and an excess of electron holes. Again, as in the case of AgC1, should the molecular forces responsible for the magnitude of the interface free energies, ?sG and ?sL, be significantly altered by the presence of these surface defects then significant differences in flotation results will be noted as the concentration of these defects is varied. EXPERIMENTAL To test this hypothesis flotation tests were conducted on pure and doped AgCl and on PbS doped with either Bi2S3 or Ag2S. Preparation of the AgCl samples was performed as follows: AgCl and weighed amounts of CdC1, were melted in a porcelain crucible. The melt was then forced through a capillary tube and the particles emitted solidified in air as they fell about 1.5 meters. Spherical particles, -0.50 + 0.25 mm, were separated from the remaining solidified material

Jan 1, 1963

By George A. Komadina

The Pima mine lies 20 miles southwest of Tucson, Ariz., and 45 miles north of the Mexican border. It is located on a hillside overlooking Tucson, which allows for gravity flow generally through the plant. In April 1965, an expansion was authorized by the mine's board of directors. This will triple the mine's output to 18,000 tpd. At this rate, it is estimated that there is sufficient ore to last 20 years.

Jan 6, 1965

By E. A. Khopunov, V. I. Revnivtsev

The process of triboelectric separation from the point of view of its potential for selective separation of various mineral particles can be described as "dry flotation." Large scale practical applications of this technique are limited because suitable models which can describe contact charging of mineral particles have not been developed. Among the various concepts a promising one is an attempt to change development in dielectric minerals within the limits of contact phenomenon in semiconductors. Experimental investigations reported in this paper indicate that the charge development is mainly a result of contact electrification of dielectric minerals characterized by "donor" and "acceptor" type energy spectra due to lattice defects.

Jan 1, 1980

By C. D. Henry, M. L. W. Jackson

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of state and federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1984

By Gordon A. Gross

Banded siliceous manganese-iron bearing sediments recognized as distinctive facies of Algoma-type iron formation constitute low-grade resources of manganese in many countries. Manganiferous facies associated with oxide and carbonate facies of iron formation have iron to manganese ratios ranging from 0.2 to 2 and commonly about one. Manganiferous facies up to 30 m thick occurring separately or with other iron formation facies are associated with cherts, carbonates, shales, turbidites, tuffs, and lavas. Primary cherty manganiferous facies and their gondite metamorphic equivalents represent significant manganese resources and are protores for higher-grade deposits derived by secondary enrichment processes.

Jan 1, 1983

By Edgar A. Scholz, Attilio G. Spat

The rapid worldwide increase in labor costs, prices of goods and services, and the rising tide of economic nationalism do not bode well for the future of mineral exploration and the mining industry. The increasing complexity and difficulty involved in finding economic mineral deposits makes these trends particularly significant. A comparative cost analysis of domestic and foreign exploration projects which developed into mines during the period 1960-74 may be useful in indicating the general nature of exploration expenditures as these trends continue. This analysis is based on a survey of 18 US and Canadian mining companies. Due to the inexact nature of exploration expenditure data, plus the fact that no two mining companies follow the same system of cost allocation, the results of the survey must be considered quite general in character.

Jan 6, 1977

By B. K. Parekh, W. M. Goldberger

A novel process is proposed for continuous removal of ash and unreacted solids which become suspended in the oils obtained during coal liquefaction. The proposed method uses water in direct contact with the oil under conditions which cause the suspended residue solids to transfer from the oil to the water phase. Separation of the phases yields a product oil essentially free of suspended solids. The water is cooled, clarified or filtered by conventional low-cost systems, and recirculated. The paper describes experimental work leading to development of the novel concept and includes the result of batch experiments that establish the feasibility of the process.

Jan 1, 1980

By John B. Goddard, David R. Brosnahan

Leaching of uranium in situ from sandstone deposits with ammonium carbonate solution containing dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However, because of their high reducing capacity and their relative abundance, the FeS2 minerals consume the bulk of the oxidant. A pressure leach apparatus was constructed that permitted measuring oxygen consumption by FeS2, best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1983

By N. J. Grant, C. C. Wang

The Ti-Cr-O ternary system has been studied in detail near the titanium-rich corner within the limits of 10 wt pct 0, and 20 wt pct Cr. Studies were extended, but not in detail, to the region beyond 25 wt pct 0, (50 atomic pct) and 62 wt pct Cr (60 atomic pct). Four isothermal sections at 1400°, 1200°, 1000°, and 800°C are presented as well as two vertical sections at 1 and 2 wt pct 02. DURING the last decade much interest has been shown in the development of high strength titanium alloys for high temperature and corrosion resistant applications. Extensive research is being carried out at present, as the current literature indicates, in order to study the properties of titanium and to develop improved alloys. Two of the important alloying elements in commercial titanium alloys are chromium and oxygen and it would be desirable to know their combined influence upon titanium. For this purpose the present work was carried out to investigate the titanium-rich corner of the ternary system TiICr-0. The binary systems Ti-Cr and Ti-0 have been published recently. The Ti-Cr system was studied by several investigators " and their results are in close agreement. The eutectoid decomposition of the B phase has been shown to be extremely sluggish. TiCr, was the only intermetallic compound found in this binary system and was formed at 1350°C by a transformation from the p phase. TiCr? was established as the cubic C 15 (MgCu,) type of structure with 24 atoms per unit cell and was designated as the y phase. This terminology will be adopted in the present work. There was disagreement about the actual composition of this compound among the several investigators, although it is evident from their data that the compound probably has a solubility range of about 2 to 3 pct and is in the vicinity of 65 pct Cr. It has been indicated recently that a high temperature modification of this y phase (TiCr,) existed at a temperature above 1300°C." ' This high temperature modification was identified as a hexagonal C 14 (MgZn,) type of structure with 12 atoms per unit cell. The exact transformation temperature from the high temperature phase to the low temperature phase has not been established. A considerable hysteresis was observed and, due to the sluggishness of this transformation, the high temperature phase often co-existed with the low temperature phase at temperatures below 1300°C. A preliminary study of several Ti-0 compounds and the Ti-0 system had been carried out by Ehr-1ich."-"' The most complete binary Ti-0 system was the one reported recently by Bumps, Kessler, and Hansen." The first intermediate phase found in the system was the 8 phase which formed by a peritec-toid reaction of the phases a and Ti0 at temperatures below 925 °C. This reaction is extremely sluggish. The structure of this 8 phase was tentatively identified by these authors as being tetragonal and the lattice constants were found as c,, - 6.645A, a,, = 5.333A and c/a = 1.246A. Experimental Procedure The raw materials used for this investigation were TiO,, electrolytic chromium, iodide titanium, and sponge titanium. The TiO, was in the form of powder of chemically pure grade (99.8 pct pure). The chemical analysis of the electrolytic chromium was: 0, 0.50 pct; Fe, 0.07; Cu, N, and C, 0.01; and Pb, 0.001. The oxygen in the chromium was calculated as part of the final oxygen content of the alloys. The alloys were prepared by the cold crucible method using a tungsten arc. The entire system was evacuated and flushed with purified helium three times and then filled with helium. Each alloy was melted, turned over, and remelted at least four times to insure homogeneity. The total melting time was generally from 6 to 10 min. A master alloy of 25 pct 0,-75 pct Ti was prepared to facilitate alloying by melting compacts of TiOl powder with either iodide or sponge titanium, yielding the compound TiO. It was found necessary to bake the TiO, powder compact at about 150°C to remove adsorbed moisture. This was done to prevent the disintegration and spattering of the compact when the arc was struck. TiO, powder dissolved quite readily into the melt and no other trouble was encountered.

Jan 1, 1955

By Milton C. Neul

As recently as the mid-1930's, steam and rail haulage were still the primary means of moving large quantities of rock. However, 2- to 5-ton standard on-highway trucks were beginning to be used in the mining industry's efforts to lower haulage costs. It was quickly obvious that rubber-tired equipment was more flexible, faster and more maneuverable. The trend towards haulage trucks had begun. Now while savings were being realized, the severe operating conditions encountered in open pit operations proved too much for the lightly constructed frames, gasoline engines and highly inflated tires. As a result, a few years later, the first 10 to 15-ton, two-axle heavy duty trucks were designed specifically to operate under off-highway conditions.

Jan 3, 1966

By T. D. Yensen

IF the question should be asked at this time: "Does pure iron have allotropic transformations?" the reply would necessarily be, "We do not know." And it is doubtful whether anybody, anywhere, is in a FIG. 1.-EFFECT OF CARBON ON HYSTERESIS LOSS OF IRON-SILICON ALLOYS. (ALL OTHER IMPURITIES AND EFFECT. OF GRAIN SIZE ELIMINATED.) position to make any other reply at this time, for the simple reason that pure iron has not yet been made and tested. The nearest approach to it contains either an appreciable amount of carbon or else an appreciable amount of oxygen (a few hundredths of a per cent.). But why be con-

Jan 1, 1929

By F. M. F. Cazin

In my first paper, relating in general to the movement of solids in a medium, I stated a newly-discovered natural law, and explained its application to mechanical ore-concentration. This law, as applied primarily to the motion of ships in water, had been announced, demonstrated and defended by me in the Journal of the Franklin Institute for March, April and May, 1893, and has not been controverted since then. I therefore contented myself in my first paper with the simple statement of it; and in order to avoid unnecessary repetition, I refer the readers of this paper to that statement (ante, p. 81) and to the earlier publication already mentioned.*

Jan 1, 1895

By H. H. Haung, J. D. Miller, E. F. Pereira

The chemistry of copper extraction from ammoniacal solutions by hydroxyoxime extractants was studied Equilibrium measurements were made by shakeout experiments with subsequent analyasis of the aqueous and/or organic phases The kinetic experiments were carried out in a single drop reaction cell in order to establish the details of the intrinsic reaction kinetics for this system. Equilibrium measurements Indicated that the extraction involves complete displacement of ammonia ligands from the coordination sphere of the cupric ion by the extractant molecules The extraction reaction has the following stoichiometry

Jan 1, 1981