Search Documents

By B. D. Cullity, O. P. Puri

The magnetostrictia of nickel after increasing amounts of plastic elongation was measured at field strengths up to 1500 oe. In addition, the residual stress was measured by means of X-ray line shifts. The observed decrease in magnetostriction following plastic strain is shown to be associated with residual compressive stress. If a metal bar, whose longitudinal axis is taken as the x direction, is plastically elongated in the x direction and then unloaded, X-ray diffraction measurements will indicate the presence of a residual compressive macrostress 0%. However, stress measurement by means of mechanical relaxation does not reveal any macrostress. In a previous paper1 the fictitious macrostress indicated by X-rays was ascribed to a particular distribution of micro-stress, namely, one in which the bulk of the material was stressed more or less uniformly in compression and a very small portion in tension. It was shown that this distribution would account for Neurath's measurements2 of magnetic losses in silicon steel, because of the effect of residual stress on magnetostriction. The present paper is concerned directly with magnetostriction, in nickel, and with the effect on magnetostriction of the residual stress created by plastic elongation. The residual stress was determined by measurements of X-ray line shifts. MATERIAL AND METHODS Commercially pure "A" nickel was investigated. Its nominal composition, in weight percent, is 99.4 Ni + Co, 0.2 Mn, 0.15 Fe, 0.1 Cu, 0.1 C, 0.05 Si, and 0.005 S. Magnetostriction was measured by means of SR-4 electrical-resistance strain gages mounted on specimens 1/4 in. sq and 8 in. long. Magnetic fields up to about 1500 ce were provided by a multilayer, non-cooled solenoid. A considerable amount of heat was developed at the higher field strengths, and, to avoid errors due to changes in the specimen temperature, the following procedure was adopted. Each measurement of the magnetostriction X at a particular field strength H was preceded by demagnetization and an adjustment of the strain indicator to zero; the field H was then quickly switched on and the strain read immediately. Curves of ? vs H were flat for field strengths above about 750 oe for all specimens, and this constant value of X was accordingly taken as the saturation magnetostriction ?s The X-ray measurements of residual stress were made with a Norelco diffractometer on specimens cut from flat bars 1 1/4 in. wide, 1/8 in. thick, and 12 in. long. These measurements were confined to lattice planes parallel to the surface of the specimen. Two reflections were studied: the 311 CrKß line at 28 = 157 deg, and the 420 CuKal line at 28 = 155 deg. The line centers were determined by fitting a parabola to the peak of the line, as suggested by Ogilvie3 and as modified by Koistinen and Marburger.4 The CuKa doublet from the plastically elongated specimens was first resolved by the Rachinger method5. All X-ray measurements were made by counting at fixed angular positions. RESULTS The results of the magnetostriction measurements are shown in Fig. 1 and Table 1. The magnitude of

Jan 1, 1963

By H. J. Beach, W. C. Goins

The laboratory development and field use of oil well cement compositions* with high resistance to drilling mud contamination are described. Resistance is obtained by adding a I-lb mixture composed of three parts paraformaldehyde to two parts sodium chromate tetra-hydrate for each sack of cement. This mixture neutralizes the cement-retarding properties of quebracho and other tannins, starch, sodium carboxymethylcellu-lose, Ignite, and monovalent salts of lignosulfonic acid. The retarding properties of calcium lignosulfonate are unaffected. The decontaminating mixture may be used in common cement (designated Type I by ASTM specifica-tions,' Class A by API Std. 10A2) or in a slow set slurry prepared from common cement by addition of calcium lignosulfonate. No changes in slurry viscosities or thickening times are caused by the protecting reagents. The method has been used in 185 field jobs where an improved success ratio has been obtained in plug setting. INTRODUCTION Field experience and laboratory investigations have established contamination by drilling mud as a major factor in oil well cement failures. During 1955, 12 attempts were required to set six open-hole cement plugs in the Timbalier Bay field, La. Eighteen to 30 hours elapsed between placing and testing the plugs in preparation for sidetracking operations. Considerations of rig time expense required immediate resetting where soft cement was drilled after a reasonable waiting period. Sea water drilling mud was used in each well and daily additions of thinners, usually lignites, had been required. Sodium carboxymethylcellulose had been added regularly to control fluid loss. The 50 per cent plug failures were attributed primarily to contamination by the mud. Similar experiences can be found in other fields along the Texas and Louisiana coasts where drilling muds normally contain large quantities of organic treating materials. Cement contamination was the subject of a survey by the Mid-Continent District Study Committee on Cementing Practices and Testing of Oil-Well Cements of the API.3 Data collected from member laboratories and released in Sept., 1951, reported the effects of a number of drilling mud treating chemicals on cement. The study revealed that many of the additives, notably the organic materials in relatively small quantities, had marked effects on the properties of cements tested. Severe losses in strength and erratic thickening time resulted from small additions of mud treating chemicals such as quebracho, starch, sodium carboxymethylcellulose, and lignite. The report included no recommendations of methods for overcoming the problem. One investigation of the contamination problem reported the successful use of activated charcoal in setting cement plugs after conventional slurries had failed.4,5 The investigation indicated that an optimum concentration of 5 per cent activated charcoal was effective in combating contamination from 16.7 volume per cent of treated mud. Laboratory and field muds were included in tests and contained varied quantities of ode or more of the following: quebracho, caustic, starch, lime, and calcium lignosulfonate. The function of the charcoal appears to be physical, removing the organic materials by adsorption. The method may be employed in API Class A or Class D (unretarded slow set) cements. The chemical approach presented here is based on

Jan 1, 1958

By Raymond Ladoo

THE milling of talc, as is the case of many non-metallic minerals, until recently, has not received adequate technical consideration, for the talc industry has become of importance only within the last decade. At first, talc was used only in the massive form, for foot warmers, griddles, and so on, and milling methods were unnecessary. As the demand for ground talc increased, producers adopted the machinery used in the milling of flour; in fact, many talc mills were rebuilt flour mills. Improvement has been slow, but today several types of grinding and separating machinery are in use; many of them, however, are still inadequate and inefficient. To determine the best methods of milling talc, it is necessary to understand the essential properties a talc must possess to fit it for a particular use. For toilet purposes, whiteness, freedom from lime and grit, fineness of grain, and good "slip" are essential. As a paper filler or coating, the talc must be white, have a good slip, be free from grit and iron, uniform, and fine grained; freedom from lime is a disputed point. Fibrous talc is supposed to be superior to massive on account of the interlocking of grains in the paper, thus increasing its strength; this point, though, is in doubt. In general, talc for the paper industry need not be of as high quality or as fine grained as that used for toilet purposes. Talc is usually bought by sample, for which reason it is difficult to state the essential properties for use in paint, rubber, roofing, and so on. The adoption of standard screen tests and standard grades by producers is necessary before an accurate basis for manufacturing or selling standards can be established. Off-color tales might be utilized, as in Germany and-Austria, by the establishment of standard grades of colored tales.

Jan 1, 1921

By E. Hornbogen, R. C. Glenn

Copper precipitates from a iron as fcc E phase without formation of intermediate compounds. In the first stage of the precipitation, spherical particles with diameters < 100A are formed at a high rate. During the second stage, the particles grow at a rate given by Zener&apos;s equation for growth of a spherical precipitate. In the third stage, growth is slower. Rod-shaped particles form after long aging times at 700°C. Maximum strengthenzng was observed at the beginning of the second step of precipitation. During plastic deformation of the aggregate, particles appear to deform initially by twinning. THE work discussed herein was part of a study of precipitation of substitutional elements from a iron. Copper was chosen as one of these substitutional elements because it has about the same atomic size as a iron, and does not form an intermetallic compound with iron. The data on the iron-copper system then available were summarized by Daniloff1 several years ago. The solubility of copper in a iron has been determined by electrical conductivity measurements,2 lattice parameter measurements,3 and by saturating thin iron foils with copper and determining the copper content.4 The results of the three investigations do not agree very well, but the value of 2.4 wt pct for the maximum solubility at 840°C seems to be the most reliable,4 Fig. 1. An alloy containing 1.23 wt pct Cu was used in our work to assure starting with a completely homogeneous material. On the copper-rich side of the diagram, there is a maximum solubility of about 4 wt pct Fe in copper at 1094°C ( phase). The precipitation of

Jan 1, 1961

By John S. Bell, J. M. Shepherd

pressure difference of 280 psi measured initially on opposite sides of the major fault in the Hawkins Field led to pressure determinations in the Woodbine sand throughout the East Texas basin. Considering the large area, there is unusually good correlation between pressure losses and points of major withdrawals, these losses indicating that the basin pressure has been materially reduced by withdrawals, primarily from the East Texas Field and secondarily from the old fault-line fields of Limestone and Navarro counties, with the pressure loss varying inversely with the log of the distance from these two main areas of basin withdrawals to the measurement points. Apparently faults located throughout the basin serve as local blocks to continuous pressure gradients. INTRODUCTION The pressure anomalies found in the Hawkins Field, Wood County, Texas,&apos; shortly after discovery have led to an area-wide investigation of the pressure distribution within the Woodbine sand of the East Texas basin. These pressures were obtained by drill-stem tests made for that sole purpose while drilling wildcat wells to deeper horizons. The Woodbine sand of Gulf Cretaceous Age is or has been productive of oil and gas in 42 different fields, with the 28 oil fields currently active having produced 118,000,000 bbl of oil during 1949. With one exception, producing energy for all Woodbine reservoirs has been from water drive provided predominantly by expansion of the tremendous volume of water contained in the Woodbine sand. This producing mechanism was recognized at an early date and was described mathematically by

Jan 1, 1951

By E. S. Tankins

The main purpose of this work was to study the effect of gold on the activity coefficient of oxygen in the liquid Fe-Au alloy and to determine how copper and silver change the activity coefficient of oxygen. A preliminary investigation has been made of equilibrium in the reaction of hydrogen with oxygen in some of the liquid gold alloys. The experimental method, which has been described in detail elsewhere,&apos; consisted of bubbling accurately known H-A-water vapor mixtures through the Fe-Au alloys contained in alumina crucibles within a vertical closed furnace. When equilibrium was reached, the samples were quenched by rapidly lowering the crucible under an atmosphere of argon to a water cooled brass fixture at the bottom of the furnace tube. The melts were found to freeze from the top in less than 4 sec. The heats were carefully prepared for oxygen analysis. The oxygen content was determined by vacuum fusion analysis.&apos; Only high purity electrolytic materials were used in this investigation. The activity and free energy of oxygen in the liquid iron alloys were studied by means of the reaction; The data for the 80 Fe-Au alloys, obtained as a function of temperature, are summarized in Table I and presented in Fig. 1, where log is plotted against . The results can be expressed by: The data were obtained using water vapor-hydrogen ratios between 0.04 and 0.30, and a 25 pct H2-75 pct A mixture. An oxygen content between 0.030 and 0.060

Jan 1, 1970

By John S. Bell, J. M. Shepherd

pressure difference of 280 psi measured initially on opposite sides of the major fault in the Hawkins Field led to pressure determinations in the Woodbine sand throughout the East Texas basin. Considering the large area, there is unusually good correlation between pressure losses and points of major withdrawals, these losses indicating that the basin pressure has been materially reduced by withdrawals, primarily from the East Texas Field and secondarily from the old fault-line fields of Limestone and Navarro counties, with the pressure loss varying inversely with the log of the distance from these two main areas of basin withdrawals to the measurement points. Apparently faults located throughout the basin serve as local blocks to continuous pressure gradients. INTRODUCTION The pressure anomalies found in the Hawkins Field, Wood County, Texas,&apos; shortly after discovery have led to an area-wide investigation of the pressure distribution within the Woodbine sand of the East Texas basin. These pressures were obtained by drill-stem tests made for that sole purpose while drilling wildcat wells to deeper horizons. The Woodbine sand of Gulf Cretaceous Age is or has been productive of oil and gas in 42 different fields, with the 28 oil fields currently active having produced 118,000,000 bbl of oil during 1949. With one exception, producing energy for all Woodbine reservoirs has been from water drive provided predominantly by expansion of the tremendous volume of water contained in the Woodbine sand. This producing mechanism was recognized at an early date and was described mathematically by

Jan 1, 1951

The dictionary defines &apos;jargon&apos; as "barbarous or debased language ". This description does not suffice. Quiller-Couch has said, it is "a kind of writing which, from a superficial likeness, commonly passes for prose in these days, and by lazy folk is commonly written for prose, yet actually is not prose at all ". The two main vices of jargon, he says, are "that it uses circumlocution rather than short straight speech", like the Babu who reported his mother&apos;s death by saying: "Regret to inform you, the hand that rocked the cradle has kicked the bucket ". Its other chief vice is that "it habitually chooses vague woolly abstract nouns rather than concrete ones", like the newspaper statement, "He was conveyed to his place of residence in an intoxicated condition", instead of saying, "He was carried home drunk". Jargon is "an infirmity of speech", it is not journalese, but akin to it. "Like respect- ability in Chicago, jargon stalks unchecked in our midst" and renders much technical writing ridiculous. It deals in periphrasis instead of going straight to the point, it loves the abstract rather than the concrete, it dabbles in words of sound rather than of meaning. Avoid it, despise it, if you purpose earnestly to write well. "In literature as in life he makes himself felt who not only calls a spade a spade but has the pluck to double spades and redouble." * Jargon is rampant in technical publications. Catalogues and other advertisements are conspicuous offenders, but with these the critic is not concerned, except in so far as such &apos;write-

Jan 1, 1931

By Albert Walcott

THE success of various operations in the manufacture of optical glass depends, in a large measure, on the ability to maintain proper heat control. A good pyrometer system is, therefore, a very necessary part of the equipment needed. Men of long experience in dealing with high temperatures, who have acquired through constant practice the ability of judging approximate temperatures by means of color, are undoubtedly valuable, but even the most competent are not as reliable as a good pyrometer system. They admit that their ability to judge accurately varies from day to day and that their judgment is affected considerably by the condition of the sky, whether it is clear or cloudy. Besides, where it is a matter of only a few weeks to train a man to operate a pyrometer system, it takes about as many years to train him to judge temperatures by the state of incandescence. The pyrometer outfit in use in the glass plant of the Bausch & Lomb Optical Co. consists of the following: Platinum elements, optical pyrometers; base-metal elements, indicators, potentiometers, and recording pyrometers. Platinum Elements and Optical Pyrometers.-Temperature control in - the melting operation is of such great importance that it is very desirable to know the exact temperatures, relative temperatures being of little value. The use of the platinum element is to determine the rate of heating or cooling of the furnace. The platinum couple is installed in either the crown or the wall of the furnace. It is placed first in a porcelain protecting tube and this is placed in a permanently fixed fireclay tube projecting from 1 1/2 to 2 in. into the fire-chamber. It has been found impractical to use the platinum couple for determining exact temperatures of the melting furnace, for the platinum element deteriorates rather rapidly at the high temperatures used, 2500° to 2700° F. (1371° to 1482° C.). When protected and installed as described, though,

Jan 9, 1919

By N. J. Grant, D. S. Bloom

THE development of high temperature, high stress alloys had proceeded with such rapidity during the war, and for a short time afterward, that our knowledge of the constitution of the alloys had become seriously inadequate. To interpret correctly alloy behavior it is not only necessary to recognize the phases present, but also to know the properties of the phases under all varieties of conditions and treatments. Chromium in these high temperature alloys holds the unique distinction of being the only one element which must be present when an oxidizing or generally corrosive atmosphere is present and when a long life is desired in service. Carbon and nitrogen must also be considered where chromium is present. Carbon is always present, either as an impurity in the raw alloying elements, or as a deliberate addition agent to increase the strength. Nitrogen is generally picked up from the atmosphere during melting or may be added as an alloying element. The effect of nitrogen additions is not too dissimilar to that of carbon additions. As such, chromium carbides and nitrides become of great interest since they are present in a very large number of alloys, including alloy steels, stainless steels, super alloys, and the like. In the chromium-carbon system there are three accepted, carbides: Cr,C, Cr7C8, and Cr3C2. The existence of one more carbide, a still higher carbon form CrC, has been advanced. The phase diagrams of chromium and carbon as published by Friemann and Sauerwald² and by Tofaute, Kuttner and But- tinghaus³ -do not extend beyond the carbide Cr3C2, which contains 13.3 pct carbon; but Hatsuta has extended the diagram up to 20 pct carbon, and in doing so hypothesized, with the use of some questionable experimental results, the compound CrC. This carbide would contain 18.75 pct carbon, 81.25 pct chromium, by weight. It is further known that as the chromium carbides increase in carbon the acid resistance increases but the oxidation resistance decreases4,5 This is of great importance in high temperature alloys where time-temperature stability, as well as oxidation resistance, is of prime importance. The possible existence of a carbide of the formula CrC thus becomes of prime importance and it was considered important to recheck the chromium-carbon binary constitutional diagram for such a compound. In view of the wide spread of values listed for the melting point of chromium (1500° to 1850°C) and 1930°C8, it was considered .that the liquidus temperatures might well be redetermined more ac-

Jan 1, 1951

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.&apos; In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By P. R. Sperry

Aluminum alloy 3S was examined to determine the relationship between the applicable phase diagram and the microstructures produced under conditions tending toward non-equilibrium as well as equilibrium. The only phases present in the alloy were aluminum, (Mn,Fe)A16, aAI(Mn,Fe)Si, and silicon. It was found that the alloy behaved essentially as though it belonged to the Al-Mn-Si system. The effects of various solidification rates and of various homogenization treatments were studied. Particular attention was given to a nonuniform precipitate distribution which reflected the solute distribution in the cast aluminum solid solution. Some possible explanations for the solute distribution based on characteristics of the Al-Mn-Si or AI-Mn systems were discussed. ALUMINUM alloy 3s (aluminum plus 1.25 pct Mn) is one of the oldest and the most widely used of the wrought aluminum alloys. In spite of this fact, there are some aspects of the metallography of 3s which have not been revealed or which have not been brought to the attention of the metallurgist working with the alloy. The purpose of this investigation was to demonstrate in general how some of the fundamentals of equilibrium phase diagrams may be applied to the study of an alloy and to show specifically the origin of certain metal-lographic features of aluminum alloy 3s. It is hoped that this information can serve as a basis for solving specific problems relating microstructure to such things as mechanical properties, recrystallization, grain growth, and surface finish. Literature Survey Considering that alloy 3s contains only one alloying addition, manganese, it seems reasonable that it would have characteristics pertaining to the A1-Mn system. However, those characteristics might well be altered by the impurities in the commercial alloy, especially iron and silicon. Therefore, not only the simple binary but also more complex systems had to be reviewed. One characteristic of the A1-Mn system worthy of mention is its sluggishness, which leads to conflicting solubility data1,&apos;2 and makes it relatively easy to supersaturate the solid solution and shift the eutectic composition during rapid solidification.3&apos;4 Another characteristic is the strong influence which small amounts of impurities, especially iron, exert in lowering the solid solubility of manganese. Undissolved manganese is ordinarily present in an intermetallic phase, MnAl,, having an orthorhombic crystal structure. A metastable precipitating phase designated as "G" has been reported but small amounts of iron and silicon suppress this phase entirely." Raynor has established that MnA1, can dissolve a considerable amount of iron by a substitution of iron for manganese atoms up to 50 atomic pct.&apos;" Consequently, in the Al-Mn-Fe liquidus diagram, the eutectic valley separating the primary aluminum and (Mn,Fe)Al, fields is fairly close to a constant Mn + Fe content." This is an important consideration in regulating the composition of 3s and also other aluminum alloys with high manganese additions."

Jan 1, 1956

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.&apos; In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By James W. Halley

&apos; FINE-GRAINED " steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth; inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of&apos; aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn&apos;s original carburizing test at 1700°F. or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was fine grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn&apos; gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not .coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Hough2 reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652~ and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvement in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement5 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved thy low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04and 0.06 Per cent added aluminum. The

Jan 1, 1946

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

By Charles Shamel

I FEAR most of the Institute members are already weary of the perennial controversy about the apex law. I feel that way about it myself now, though I have been guilty of considerable contribution to the discussion in the past. The discussion does not seem to perceptibly influence previously held views and I would not again break into print on the subject but for the urgent invitation of the Chairman of our, Law Committee. This energetic and able member has firmly determined to secure a revision of the mining law and among other things to eliminate the so-called apex provision from the U. S. mining statutes. He is, however, fair about it and has invited me to make "the strongest possible argument in its favor." I am suspicious that he is acting on the psychological principle that it is usually easier to convince an audience against a cause vigorously but unsuccessfully defended than against one wholly mute. Nevertheless, I realize that personally he wishes me no harm, much as he hates the apex law, and so am willing that the Institute have whatever benefit may accrue from my taking up again the unpopular side of the discussion. I say this because the attitude of a large part of our "articulate" membership seems irreconcilably hostile; their minds are made up; favorable consideration is foreclosed; and they become impatient and even sarcastic at any attempt to elucidate a favorable view of the apex law. The exact question for discussion at the present time is not whether on abstract, or any other considerations, the apex law is the best possible rule, but the very different proposition whether, after nearly 50 years of statutory life and much longer as a practically universal miners&apos; custom, it is now just and expedient to repeal the apex law.

Jan 4, 1914

By C. B. Murray

"OUR experience from time immemorial has been that the furnace sampler and analyst usually find one or two, and sometimes more, points less iron than the Lake Superior shippers, but, fortunately, their contracts are `iron bound&apos;; and, generally speaking, analyses at this end are practically useless, for we are obliged to settle on basis figured out to a half dozen decimals, and, as a rule, without recourse in the event of flagrant discrepancies between the two analysts." The above is an extract from a letter received by the writer of this paper from the President of an iron company, discussing the question of sampling. It so well expresses the opinion of many blast-furnace owners and managers that it seems a suitable text for a discussion concerning the need of uniform methods of sampling. If all railroad cars were loaded the same, if all stock piles were the same shape, and if ore was received regularly each day, the problem of sampling would be comparatively simple. The conditions, however, vary widely at different places, and at the same place from day to day, and it is probably impossible to determine upon any one method of sampling which will apply at all times and in all cases. However, it would seem as though some general principles might be suggested which would tend to overcome these wide differences in samples of the same thing. The sampling of a cargo of iron ore begins at the breast of ore in the mine. The ore is sampled from the mine cars, from the stock piles, and from the railroad cars at the mines. At the lower Lake ports the ore is practically all sampled from the boat, occasionally from railroad cars. At the furnaces, the ore is nearly all sampled from railroad cars and occasionally from stock piles.

Jan 1, 1914

By Fred Wright

IN A recent paper1 a detailed discussion is given of the possibilities. of using polarized light in the examination of opaque substances. The factors underlying the problem .are there treated from the viewpoint of the electromagnetic theory of light and the presentation is necessarily mathematical in form. The practical methods resulting from the discussion are, however, relatively simple and promise to be of value in the determination of certain ores and metals when studied in reflected light under the microscope. The results of the theoretical investigation referred to may be summarized by stating that in general the optical constants, such as refractive indices and absorption indices, cannot be satisfactorily ascertained on small, random, polished sections; that the use of polarized light enables. the observer ordinarily to determine whether the crystal plate is isotropic or anisotropic, and also to ascertain the degree of anisotropism; that for this purpose methods based either on the contrast in intensity between the two reflected components of non-polarized light, or on the amount of rotation of the plane of polarization, on reflection, of vertically incident, plane-polarized light, may be employed; that methods based on the phase difference between the two reflected components are in general of little value because of the small differences in phase which ordinarily result for a relatively large change in birefringence or biabsorption. The measurement of the optical properties of transparent minerals, even in minute irregular grains, is a simple task with modern petrographic microscope methods and is accomplished by petrologists as part of their ordinary routine work. But the determination of the optical constants of opaque substances is difficult and is rarely attempted; all observations are necessarily made in reflected light and are restricted commonly to the determination of color, of hardness, of the character of crystallization, and

Jan 2, 1920

By John C. Calhoun, F. W. Gooch, J. P. Everett

The results of two sets of displacement experiments are reported. In the first set of experiments various solutions of sugar in water were displaced by other solutions of sugar in water. In the second set oils were displaced by water. Each set of experiments was performed on a linear system made of cemented silica sand grains. These displacement tests were made to evaluate the behavior when the ratio of fluid viscosities between the displacing and displaced phases was varied. A further consequence of the test results is a comparison between displacement behavior when the displaced and displacing phases are miscible as with sugar solutions and when they are immiscible as with oil and water. INTRODUCTION Buckley and Leverett1 have presented a theory for the displacement of oil by gas or water based upon the relative permeability concept. This theory presents the displacement of oil as occurring in two phases, an initial or primary phase preceding the breakthrough of the displacing phase and a subordinate or secondary phase during which both oil and the displacing phase flow simultaneously through the same porous section. These authors gave the results of calculations to show that the percentage of oil displaced during the primary phase by water drive would be dependent upon the ratio of the viscosity of the oil to that of the water. No experimental evidence was reported by these authors to substantiate their theory. Qualitatively, however, it has been found to be in agreement with many observed field results. Laboratory investigators have been in general agreement in reporting for air or gas drive2,3 a small primary phase of production and a large secondary phase. Reported investigations on water drive3,4,5 have shown instances where both primary

Jan 1, 1950

By Nathaniel Arbiter

INTRODUCTION Almost seventy-five years ago problems in the recovery of sulfides from then designated slime fractions were the impetus for the development of flotation. The fall-off in recovery by gravity methods below about 200-mesh, and the shift from coarser vein deposits to more disseminated ores, particularly for copper, provided the background for flotation&apos;s rapid advances. Although the ensuing years have witnessed major improvments both in flotation reagents and in flotation machines, many problems are still with us. And since, with the exception of the unique leaching of chalcocite ores at Inspiration, flotation is still the exclusive mainstay for primary recovery of all base metal sulfides, the solution of these problems as they arise is vital to the well-being of the mining industry. Before considering the problems themselves, it will be useful to review the current status of sulfide flotation in the United States. The last comprehensive survey by the Bureau of Mines in 1975 (1) showed sulfide ore tonnages treated from 1960 to 1975 as summarized in Table 1; Table 2 gives similar data for the flotation of all non-sulfide ores. Noteworthy is the leveling off in sulfide ore tonnages in 1970-1975, with a probable further decline in the past three years, and the sharp drop in the number of plants floating sulfide ores. In contrast, the tonnages of non-sulfide ores floated, as well as the number of individual plants, has continued to increase. In spite of these trends, two-thirds of the total tonnage of the ores to which flotation is applied is still represented by sulfides. Average grades of sulfide ores in 1975 were: about 0.6 percent for copper; near 5 percent for lead; and near 3 percent for zinc. Recoveries averaged in the low 80&apos;s for copper; about 95 percent for

Jan 1, 1979