Search Documents

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By M. B. Bever, A. B. Michael

The solidification of aluminum-rich aluminum-copper alloys was investigated for different solidification rates. The measured amounts of nonequilibrium eutectic were compared with the amounts calculated on the assumption of no diffusion in the solid. The morphology of the eutectic was studied and dendritic spacings were measured. Compositions of the cored primary solid solutions were determined by quantitative autoradiography after activation of the solute copper by neutron irradiation. CONSIDERABLE progress has been made in recent years toward an understanding of the solidification of metals. This is especially true for the factors involved in nucleation, the controlled growth of metal crystals from melts, and various aspects of the freezing of ingots and castings. Many features of the solidification process, however, are not understood adequately and much further work is required. In the research reported here the solidification of a series of aluminum-rich aluminum-copper alloys was investigated. Different degrees of deviation from the idealized case of equilibrium solidification were attained by varying the rate of solidification. Thermal analysis and microscopic examination were supplemented by lineal analysis and autoradiography. The latter required the use of radioactive tracers and was adapted to the quantitative determination on a microscale of concentrations of copper dissolved in aluminum. The tracers were produced in situ by activating the copper with neutrons. These techniques permitted a correlated interpretation of the temperature-time history, the amounts of nonequilibrium eutectic and the general morphology of the alloys, and yielded quantitative data on microsegregation. Nonequilibrium Solidification In the general case of the solidification of a solid solution in accordance with the phase diagram, the composition of the coexisting liquid and solid must change continuously. This change requires diffusion, which at best remains incomplete in the solid during solidification. The resulting inhomogeneity of the solid solution crystals is well-known as coring, dendritic segregation, or microsegregation. The generally accepted analysis of coring assumes that, 1—no diffusion occurs in the solid, 2—diffusion is complete in the liquid, and 3—the composition of the solid formed on cooling through any infinitesimal temperature interval is given by the solidus of the phase diagram. On this basis, In this equation m designates mass, x designates the concentration of solute and the subscripts L and S refer to the liquid and solid phases, respectively; the subscript o indicates the initial state, in which the liquid is identical with the entire system. Eq. 1 or its equivalent has been derived repeatedly'-7 and an analogous equation, known as Rayleigh's equation, has been used for distillation. The assumptions on which Eq. 1 is based do not include an infinitely fast cooling rate as sometimes stated. In fact, Olsen and Hultgren %ave shown by experiment that very high solidification rates suppress coring, presumably by preventing diffusion in the liquid and by the effect undercooling has on the composition of the nucleus. Coring thus occurs at rates of cooling which are too fast for a close approach to equilibrium in the solid and too slow to suppress diffusion in the liquid and to cause marked undercooling. If the liquidus and solidus approximate straight lines, Eq. 1 simplifies to The fraction of liquid present at any temperature during nonequilibrium solidification can be calculated from Eqs. 1 or 2. By the lever relation it is

Jan 1, 1955

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By Burton H. Boyum

Greater depth of exploration drill holes and increasing cost of drilling have been principal factors in reviving interest on the Mar-quette Iron Range in controlled directional drill-hole deflection. This deflection is obtained by the application of the Hall-Row wedging technique. Modifications were made in the technique and equipment in the effort to simplify and strengthen the procedure. The practice is similar in many respects to the oil well type of deflection with a whipstock. Introduction The deflection of diamond drill holes by wedging was a widespread practice in Canada, South Africa and the Lake Superior District as early as 1907 to 1920. Several basic schemes were used, with local variations.' The deflecting wedge assembly was the idea of Mr. Welldon and Mr. Payne-Gallwey operating under the supervision of Mr. William Gallagher of Johannesburg, South Africa. All schemes employed some means of plugging the old hole. A footpiece of various styles was placed in the hole on the plug. In some methods, the orientation of this piece was determined before placing the deflecting wedge. Some techniques permitted continuing the hole the same size after wedging, while others necessitated a size reduction. Interest in wedging diamond drill holes in the Lake Superior District waned after 1920. The Hall-Row patented system for deflecting holes was developed in Canada about 1918.2 Interest centers on the wedging process for the following applications: 1. Maintaining a given course and inclination of the drill hole. 2. By passing an obstruction in a drill hole. 3. Resampling an ore body. 4. Exploring an area overlain by surface conditions not favorable to drilling. During the period of 1913 to 1920, The Cleveland-Cliffs Iron Co. used the wedging technique under a variety of conditions. In general, the practice was not applicable again until 1946. Meanwhile the Hall-Row system of drill-hole deflection survived years of application as the best technique available. In the intervening years, our depth of exploration has increased as well as the overall cost of drilling. As exploration becomes deeper, there is the possible economy of cutting the ore body at a moderate distance from the parent hole without redrilling from surface. Thus a branch hole started near the mid-point of a deep hole can reach the ore horizon at a considerable offset from the parent hole. This permits a greater interval between surface drill holes as drilling becomes deeper. Our interest revived in the subject and a wedging program was initiated. General Description Results The maximum theoretical angular deflection possible, based on the deflecting

Jan 1, 1949

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By Burton H. Boyum

Greater depth of exploration drill holes and increasing cost of drilling have been principal factors in reviving interest on the Mar-quette Iron Range in controlled directional drill-hole deflection. This deflection is obtained by the application of the Hall-Row wedging technique. Modifications were made in the technique and equipment in the effort to simplify and strengthen the procedure. The practice is similar in many respects to the oil well type of deflection with a whipstock. Introduction The deflection of diamond drill holes by wedging was a widespread practice in Canada, South Africa and the Lake Superior District as early as 1907 to 1920. Several basic schemes were used, with local variations.' The deflecting wedge assembly was the idea of Mr. Welldon and Mr. Payne-Gallwey operating under the supervision of Mr. William Gallagher of Johannesburg, South Africa. All schemes employed some means of plugging the old hole. A footpiece of various styles was placed in the hole on the plug. In some methods, the orientation of this piece was determined before placing the deflecting wedge. Some techniques permitted continuing the hole the same size after wedging, while others necessitated a size reduction. Interest in wedging diamond drill holes in the Lake Superior District waned after 1920. The Hall-Row patented system for deflecting holes was developed in Canada about 1918.2 Interest centers on the wedging process for the following applications: 1. Maintaining a given course and inclination of the drill hole. 2. By passing an obstruction in a drill hole. 3. Resampling an ore body. 4. Exploring an area overlain by surface conditions not favorable to drilling. During the period of 1913 to 1920, The Cleveland-Cliffs Iron Co. used the wedging technique under a variety of conditions. In general, the practice was not applicable again until 1946. Meanwhile the Hall-Row system of drill-hole deflection survived years of application as the best technique available. In the intervening years, our depth of exploration has increased as well as the overall cost of drilling. As exploration becomes deeper, there is the possible economy of cutting the ore body at a moderate distance from the parent hole without redrilling from surface. Thus a branch hole started near the mid-point of a deep hole can reach the ore horizon at a considerable offset from the parent hole. This permits a greater interval between surface drill holes as drilling becomes deeper. Our interest revived in the subject and a wedging program was initiated. General Description Results The maximum theoretical angular deflection possible, based on the deflecting

Jan 1, 1949

By Henry Hibbard

Fox the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seen to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machinery, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume.

Jan 9, 1919

By Arvid E. Anderson, Frank K. Cameron

The weathering of copper-bearing ores with the formation of a water soluble salt and the recovery of the metal by leaching and evaporation precipitation, are processes long known, which have at various times been utilized with more or less commercial success. It is commonly assumed that the technical principles involved are quite simple and their application to a particular case easy. If these assumptions were true, we should anticipate a long list of uniformly successful leaching operations, which is not the case, and one would be justified only in calling attention to either unique or peculiar features of any particular enterprise; whereas, in studying the problems of the recovery of copper from the old workings of the Ohio Copper Co. in the light of available descriptions of other leaching projects, we have not found the assistance hoped for to guide us to the best realization of our own opportunities. It appears desirable, therefore, to call attention to these guiding principles, together with a description of the facts of accomplishment. Justification lies in the fact that the leaching and precipitation of copper at the Ohio Copper Co. mine in Bingham Canyon, Utah, is successful. This success is measured by an average monthly production of 600,000 Ib. of copper at an average operating cost, to date, of 3.85 cents per pound at the company's workings, or 6.32 cents per pound after paying shipping and smelter charges on the finished copper. A total of 17,076,099 Ib. of copper had been shipped to the smelter from the beginning of operations, August, 1922, to April 1, 1925. Probably these results can be bettered with further study and realization of the factors involved and the devising of methods of meeting them. It is now an assured fact that the enterprise will have a relatively long and continuously profitable life and that its reserves will not, nor cannot, be suddenly and permanently depleted. It is particularly noteworthy that the financing of this enterprise has been entirely from its earnings. The few hundred dollars necessary for the first experiments and production were obtained by the sale of used, and no longer needed, equipment from a mill belonging to the company; and all funds since required throughout the growth and development of the enterprise, from a few troughs with a production of 2000

Jan 1, 1926

By W. D. Steele, S. D. Brady

THE Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains mineable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon¬galia Co. thence south and southwest across the state to Wayne Co. near Huntington. The Pittsburgh coal is also mineable in the Upper Potomac region but is now practically exhausted there. The total mineable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13% billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio river as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern. West Virginia District comprising Wetzel, Monongalia, Marion, Preston, Harrison, Doddridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 188o (when the Monongahela River Railroad, now B. & O. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgantown and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Monongahela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of mineable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. ECONOMIC IMPORTANCE The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1948

By Robert E. Cuthbertson

IT is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson3 by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be confined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. BRIEF HISTORY OF REAGENT PRACTICE AT CLIMAX Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium, cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 1920, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Never theless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1944

By D. O. Hobson, P. L. Rittenhouse

We have recently found that many lots of Zircaloy-2 and -4 tubing tested in tension deform to cross section shapes that are "polyhedral" rather than circular. The noncircular cross sections seem to result from a circumferential variation in plastic proper -ties and, therefore, in texture. We examined the diffracted X-ray intensity from (OOOl), {1010), {ll20}, and {1011} planes parallel to the tubing surface around the entire circumference. Tubing that deformed to a circular cross section showed <5 pct variation in diffraction intensity around the circumference from any of these planes. Greater intensity variations were found for all the tubing materials that developed non-circular cross sections during deformation. In each instance the number of intensity maxima and minima was consistent with the number of sides of the &apos;polyhedral" cross section. THE effects of crystallographic texture on the mechanical properties of zirconium, zirconium alloys, and other anisotropic hexagonal materials such as titanium and hafnium have been intensively studied. If the natural crystallographic anisotropy of these materials could be controlled by selected fabrication operations, a material could be produced with a texture, or preferred orientation, in which the maximum strength directions are in the stress directions of the structure. The permissible stress levels of the structure could then be increased. Rittenhouse and Pickle-simerl have shown that highly textured Zircaloy-2 plate can vary from 52,000 to 70,000 psi in tensile yield and from 62,700 to 122,000 psi in compressive yield strengths as a function of specimen orientation. Similar texture effects have been observed in Zircaloy tubing, whose mechanical properties differ depending upon whether the tubing has basal poles predominantly radial or tangential and upon the mode of testing. These same texture effects might be troublesome if the texture in the tubing is not uniform around the tube walls. This paper is concerned with the effects of nonuniform texture on the strain behavior of commercial Zircaloy tubing. BACKGROUND Previously, various lots of commercial Zircaloy tubing were tested under selected stress conditions as part of a program to determine the four quadrants of the yield locus. One of the testing procedures was uniaxial tension and it is the influence of texture variations on the tensile deformation behavior of the tubing that is of interest here. The effect of texture on the strain behavior in tubing is very apparent from a uni-axial tensile test.2 This behavior is illustrated schematically in Fig. 1 for three different tubing textures: 1) basal poles predominantly in the radial direction; 2) basal poles predominantly in the tangential direction, and 3) basal poles equally distributed between the radial and tangential directions. In the first example most of the grains are oriented for prism slip to operate to allow axial lengthening and diametral reduction of the tube. Reduction in wall thickness requires {1122} twinning, a more difficult operation than slip.* In the second example, the texture is such that *The singleCrystal analogy will be used quite often in this paper when strong texturesare being discussed. The textured material is assumed to react as if it were a single crystal aligned in the same orientation and under the same stress system as the predominant texture._____________________________________________ prism slip operates to give axial lengthening and wall thinning. Diametral reduction requires twinning and again should be more difficult to accomplish. A specimen with basal poles equally distributed between the radial and tangential directions should exhibit about equal diametral and wall strains.* Table I shows the *Diametral strain is accomplished by a combination of circumferential and longitudinal strains. But, for the purposes of this paper, it will be considered as a strain causing a change in the length of a specified diameter.__________ strain behavior of two lots of tubing with different textures. The first tube has a texture with basal poles equally distributed between the radial and the tangential directions. The ratio of true thickness strain to true diametral strain is almost unity. The second tube has a predominantly radial basal pole texture and it is apparent that most of the total strain has occurred by diameter reduction, just as one would predict. There is over three times as much diametral strain as thickness strain. RESULTS We found that specimens from certain lots of commercially fabricated tubing did not retain round cross sections during uniaxial testing. Instead, the speci-

Jan 1, 1970

By C. J. Bechtoldt, H. C. Vacher

Quenched alloys, prepared by powder metallurgical techniques, were examined by microscopic and X-ray diffraction methods. The compositions and heat treatments were chosen so that the chromium and nickel solvuses could be determined and a range of composition and temperature, in which a eutectoid had been reported, could be explored in small intervals. The results showed no evidence of eutectoid reactions having taken place. ALLOYS containing iron, chromium, molybdenum, and nickel are extensively used in high-temperature applications. In order to provide basic information on the solid-state reactions that occur in such alloys, the National Bureau of Standards is engaged in an extensive study of the equilibrium phases in the binary, ternary, and quaternary systems involving these four metals. Attention was directed to the chromium-nickel system because a review of the literature showed conflicting data. A recent compendium1 of the constitution of binary alloys gives two diagrams for the chromium-nickel system, one a simple eutectic and the second a diagram showing a eutectoid and a eutectic. The eutectoid was the result of an allotropic transformation in a high-temperature solid-solution form of a chromium-rich phase called 0. The approximate temperature and composition of the eutectoid was 1200°C and 30 at. pct Ni. In the preliminary study, at the Bureau, no transformation was indicated in the chromium-rich phase of ternary and quaternary alloys in which chromium and nickel were major components. Similar results have been reported from time to time in the literature,2-8 In consequence of this situation, a systematic study was made of the constitution of heat-treated chromium-nickel alloys using metallographic and X-ray diffraction methods. The compositions of the alloys were selected so as to determine the boundaries of the chromium-rich and the nickel-rich phases and to explore in small intervals the ranges in composition and temperature in which the eutectoid had been reported. The results of this study are reported and discussed in the present paper. EXPERIMENTAL PROCEDURES Materials, Alloys, and Heat Treatments—The alloys were prepared by a powder metallurgy technique similar to that used in earlier work.9 Analyses of the materials used are given in Table I. Powders were mixed using a vibrator in 30-g batches of predetermined composition; 2-g pellets were made from the mixture by compacting at room temperature in a 1/2-in. diam mold under 60,000 lb per sq in. pressure. The pellets were sintered in dry hydrogen for 10 days at 1300°C. At the end of the sintering treatment the specimens were quenched in water, which caused a pale green film to form on the chromium-rich alloys and thin black scale to form on the nickel-rich alloys. The pellets after sintering were approximately 1/2 in. diam by 3/32 in. thick. The purification train9 was modified by inserting a tube of titanium turnings, heated at 700°C to increase the efficiency of the removal of oxgen and nitrogen. It was found in the earlier work that the sintering treatment lowered the carbon, oxygen, and nitrogen contents of chromium-rich alloys to 0.01, 0.01, and 0.004 wt pct, respectively, and that there was a loss of chromium. In order to ascertain the extent of this loss, the chromium contents of certain alloys were determined chemically. They included those alloys used to determine the parameter-composition curves and those of critical composition, used to determine the chromium-solvus microscopically; these analyses were made on samples after the final heat treatments. The mixed powder values for the chromium content of those alloys that were not analyzed were adjusted to conform to a smooth curve based on the chemically analyzed values for

Jan 1, 1962

By I. A. Lesk

The various materials utilized in the construction of integrated circuits, and the resultant materials interfaces, are discussed with emphasis on a materials system that is compatible with all types of integrated circuits and minimizes the number of different interfaces. Problems with interfaces may originate in the silicon, on its surface, and between other materials within the integrated-circuit package independent of the silicon. ThE difference between integrated-circuit theory and practice may generally be spelled out in terms of the difficulties in fabricating a desired structure. There are, of course, problems in forming the requisite materials, of the necessary composition and geometry, where needed. A distinct class of problem, however, is associated with interfaces— generally between different materials, but occasionally between regions of the same material. We require that each interfacial system perform its proper electrical, mechanical, and thermal function, and do so in an unchanging manner with time under the most severe operating conditions. In a practical sense, we deal in nonideal systems, such that it is generally not possible to form an interface exactly the way it was intended, even if we allow for a knowledge of the practical limitations of the fabrication system. Another way of looking at this situation is to realize that, when we form a group of interfaces under apparently the same experimental conditions, there are often differences of important consequence between them. Very high-magnification pictures, such as are obtained by an electron microscope, reveal fine structure that often differs over the area of a given sample, as well as from sample to sample. Low-magnification pictures look better, but don&apos;t eliminate the problem. The trend towards integrated circuits, and away from circuits fabricated utilizing separate components, is very strong in many areas of electronics. A typical silicon monolithic integrated circuit, still in place in the wafer on which it was fabricated, is shown in Fig. 1. The increased reliability which is being experienced through the use of integrated circuits can, to a large extent, be credited to the reduced complexity of the interface system that is present in the electronic system. A glance at Fig. 1, however, with all of its epitaxial and diffused p-n junctions, and interconnect system, shows that interfaces have been far from eliminated. Fig. 2, depicting a schematic cross-sectional view of a (partial) typical integrated circuit, illustrates in detail the numerous interfaces that occur in this type of structure. Besides the individual circuit elements, there are interfaces for isolation, and, Fig. 3, even a crossover requires a series of interfaces. What has been accomplished, however, irrespective of whether or not the total number of interfaces in the circuit is increased or decreased, is that the variety of interfaces is very much reduced. This is because there are fewer materials involved. Since the expense incurred in an R & D program to improve reliability is pretty much directly proportional to the variety of interfaces involved, it is economically advisable to work with integrated circuits for highest reliability. That is not to say that circuits built using standard components could not be made as reliable as integrated circuits, but that the expense involved because of the more complex over-all interface system would be much greater. Although electronic performance utilizing integrated circuits with all silicon elements (i.e., transistors, diodes, resistors, capacitors) is adequate for many applications, there are numerous instances where thin-film passive elements must

Jan 1, 1965

By L. B. Gittinger

Sulfur is a nonmetallic element widely distributed in nature. It constitutes 0.06% of the earth&apos;s crust but only a very small portion occurs in sufficiently concentrated amounts to justify mining. Sulfur occurs in practically all animal and plant life. It constitutes approximately 0.09% of the elements in the oceans; it has been found in meteorites. Sulfur was known and used by man before recorded history. The American Chemical Society approved spelling for the element is sulfur. The English spelling sulphur is used commercially in the United States. In ancient times, sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Sulfur is found naturally in the elemental form in subsurface deposits associated with gypsum and anhydrite in salt domes and sedimentary formations in evaporite basins and in solfatara-type deposits associated with volcanoes and mineral springs. Sulfur occurs also in molecular combination in ferrous sulfides (pyrites and pyrrhotite) and nonferrous sulfides (copper, lead, zinc, and nickel), and in mineral sulfates (gypsum and anhydrite); as hydrogen sulfide contaminant in natural gas; as organic compounds in crude oil and tar sands; and as pyrite and organic compounds in coal and oil shales. Sulfur resources are abundant and exist throughout the world but the extent to which they can be classified as reserves is greatly circumscribed by prevailing prices and technology. Estimates of world sulfur reserves are compiled by the U.S. Bureau of Mines. A compilation of reserves by area and source of sulfur published in 1970 and presented here as [Table 1] totaled 2.47 billion tons (Lewis, 1970). The effect of the decline in prices which has occurred since the earlier estimate is dramatically illustrated by the 1972 estimate of the U.S. Dept. of the Interior which shows world sulfur reserves of only 1.2 billion tons (Anon., 1972d). Sulfur is produced commercially from one or more sources in nearly 70 countries of the world. World production of sulfur in all forms totaled 41.6 million tons in 1971. (Sulfur statistics given in this chapter are long tons.) Native deposits, sulfides and oil and gas contributed, respectively, 31, 41, and 25% of world production (Table 2). Of the sulfur produced from native deposits, salt domes accounted for 54% and evaporite basin deposits, 44%. Volcanic deposits are of little significance except for local consumption. The past two decades have seen important shifts in the world&apos;s sulfur sources. In 1950, native deposits and sulfides each supplied about one-half of the world&apos;s production. During the 1950s, sulfur recovered from oil and natural gas grew rapidly, representing about 10% of the total by 1960. Since then, the petroleum industry has continued to increase its relative importance as a source of sulfur, representing more than 30% at 1972 year-end. Sulfur is generally classified as elemental or nonelemental for statistical purposes. Elemental sulfur is sulfur produced in the pure, uncombined form. It includes production from native deposits, as well as that recovered in the elemental form from oil and natural gas or other sulfur-bearing materials. When produced from other than native deposits, it is generally referred to as recovered elemental sulfur. Nonelemental sulfur is that which is utilized commercially in molecular combination with other elements, such as sulfides or sulfates. Elemental sulfur is being produced from salt dome deposits in the Gulf Coast region of the United States and the Isthmus of Tehuantepec in Mexico, and from evaporite basin deposits in west Texas, Poland, Sicily,

Jan 1, 1975

By B. M. Larsen, T. E. Brower

IN two previous papersl,2 dealing with the carbon-oxygen reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity 0[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm,; that is, if [C] X [O] is taken as 0.00222, 0[O] = [O] - 0,00222/[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.&apos; This quantity 0[O] proves to be substantially independent of carbon content over the range 0.08 to 1.2 per cent, as well as of the basicity of the slag, and is nearly always within the limits 0.015 to 0.025 per cent when the bath is boiling normally and is in what we have termed a steady state. Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, 0[O], on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in ?[O] level following addition of Spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. VARIABILITY OF EXCESS OXYGEN IN NORMAL OPEN-HEARTH OPERATION The preceding general statements refer to the average value of ?[O] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining oxygen from the gas phase above it, or from added ore, faster than it is losing oxygen to the metal; yet when the bath starts to boil vigorously, the opposite condition may prevail for some time. The consequence of this lag is a variation of ?[O], the interpretation of which in a single heat may not be immediately obvious, This condition is illustrated in Figs. I and 2. In Fig, I, ?[O] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small ore feed causes only a small rise in 0[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1946

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years, the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture, and the ductility values can often be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel, Several types of abnormal loss of ductility can be distinguished, of which those caused by excessive amounts of inclusions of undesirable type and those caused by unsuitable grain size and ingot structure are well known. The particular type of abnormal lowered ductility currently under consideration may be distinguished by the fact that the low-temperature aging treatment necessary for its relief is insufficient to cause any visible change in the microstructure as ordinarily observed. As this aging will in fact eventually occur at room temperature, the phenomenon of present interest may be given the symptomatic definition, "Temporary Abnormal Low Ductility." Some hundreds of previous investigations, largely qualitative in nature, have established, beyond reasonable doubt, that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen-, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, The Steel Founders&apos; Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. The interest of this investigation thus extends to permanent abnormal losses of ductility, such as are caused by the inclusions which sometimes result from special deoxidizing practices and possibly from metallic nitrides, but as these can be distinguished from the temporary effect of hydrogen, they have been excluded from the work reported here except when they

Jan 1, 1948

By John Griffen

The modern anthracite breaker or washery uses almost exclusively a wet method of preparation, which requires, roughly, 1 gal. of water per minute per ton of production per day. The entire anthracite industry uses about 320,000 gal. per min. of water for this purpose or 800,000 tons of water per day. As this water leaves the breakers, it contains fine solids—coal, slate, pyrite, and clay—and is then called silt or slush; as slush is the term most commonly used, it will be employed throughout this paper. The solid content of the slush will be referred to as solids. In the earlier days of anthracite mining, little coal was washed, less crushing was employed, and virgin coal was mined exclusively. As a result, the slush problem was not acute because of the relatively small quantity and the coarseness of the solids. Such slush as was produced could usually be easily impounded and retained or could be discharged into streams without any appreciable pollution being apparent. The character of the fine waste from the breakers changed materially as its quantity increased until now about 40,000 tons of slush solids are produced daily. Second mining and robbing operations materially increased the quantity of fine solids delivered to the breaker in the mine car. The demand for chestnut, stove and egg sizes, to the exclusion of grate, steamboat, and lump sizes, requires finer crushing of the mine-run coal with a consequent increase of fine solids in slush. The use of rice and barley sizes removed a considerable tonnage of coarser solids from the slush but left great quantities of fine solids difficult to retain completely, and to store, and long considered of no possible fuel value. Despite the efforts of the coal operators, the slush solids have found their way into the streams causing, in some cases, serious pollution. The Water Supply Commission of Pennsylvania published, in 1916, a report on Culm in the Streams of the Anthracite Region,&apos; from which the following is taken: About 40,000,000,000 gal. of water carrying 10,000,000 tons of fine culm are discharged into the water-courses direct, flushed into the mines, or disposed of by various means on the surface. The extent to which the very small sizes of anthracite have been deposited in the rivers draining the coal fields is made evident by the fact that over a quarter of a million tons are recovered annually from the river beds by coal-washing operations.

Jan 1, 1922

By C. H. Mathewson, W. R. Hibbard, Robert Maddin

A satisfactory mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.&apos; Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.³ Experimental Procedure Half-inch rods of alpha brass (nominally 70 pet Cu, 30 pet Zn)* were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.4 In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pet nitric acid solution. The back-reflection Laue technique as described by Greninger6 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buer-ger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1949

By C. H. Mathewson, Robert Maddin, W. R. Hibbard

A satisfactory mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.&apos; Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.³ Experimental Procedure Half-inch rods of alpha brass (nominally 70 pet Cu, 30 pet Zn)* were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.4 In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pet nitric acid solution. The back-reflection Laue technique as described by Greninger6 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buer-ger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1949

By W. H. Bassett, C. Davis

Although brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent, copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,&apos; the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard&apos;s work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.