Search Documents

By T. B. Counselman

AN iron blast furnace of 1000 tons daily capacity will produce about 100,000 cu; ft. per minute of blast-furnace gas. This contains about 25 per cent of carbon monoxide, and has a B.t.u. value of about 95. This gas-is used primarily for heating the stoves of the blast furnace, and secondarily, under boilers, for steam production. Occasionally it is also used in gas engines. The raw gas coming out of the furnace carries about 10 grains of flue dust per cubic foot of gas, under best operating conditions. With the furnace "rolling" or slipping, this quantity may temporarily be greatly increased. This dust would, of course, deposit on the checkers of the stoves, or plug the burners under the boilers; therefore the gas must be cleaned.

Jan 1, 1936

By G. A. Zeito

Detailed visua1 examination of outcrops was used to ob-tain data on the lateral extent of shale breaks. Thirty vertical exposures belonging to maritie, deltaic and channel depositiorral environrrrents were exatmind, surveyed and photographed. The dimensions of the outcrops ranged from 356- to 8,240-ft long and 25- to 265-ft thick. Shale breaks were found to extend laterally for significant distances. and in some sands terminates by joining other break v much more frequently than by disappearance. Consequently with regard to flaw, a gross sand consisted of both continuous and discontinuous subunits. The degree of continuity of shale breaks as well as the occurrence and spatial distribution of discontinuities were different for the three depositional environments. Statistical eva1uations were performed to determine the confidence level with which estimates derived from outcrops can be applied to reservoir sands. Results of these evaluations revealed that: (I) the lateral continuity of shale breaks in marine. sands is si~nificatit, and the estimates of lateral extent can he applied to reservoir sands with a high degree of confidence (80 to 99 per cent of the shale breaks continued more than 500 ft, with a confidence of 86 per cent); and (2) the tendency for adjacent shale breaks to converge upon each other over small distances in deltaic and channel sands is highly significant (62 to 70 per cent of the shale breaks converged in less than 250 ft, with a confidence of 50 per cent), hut the probable magnitude of the resulting sand discontinuities cannot yet he predicted with adequate confidence. INTRODUCTION Almost all of the efforts devoted to characterization of the variable nature of reservoir sands have been focussed on permeability variations. Among the widely used concepts that have emerged from these efforts are those of stratified permeabilities, random permeabilities, and communicating and noncommunicating layers of different permeabilities. This study is concerned with the presence of interbedded shales and silt laminations. These features are impermeable or only slightly permeable to flow. Therefore, knowledge of the extent to which they continue laterally and the manner in which they terminate within the bodies of gross sands is important for proper description of reservoir flow. Initial field observations made on outcrops revealed that shale breaks and the relatively thinner silt laminae have impressive lateral continuity. They appeared to divide sand sections into separate individual sand layers. Although most of the layers were continuous across the total lengths of the outcrops, some were discontinuous because the- bounding shale breaks converged. Furthermore, the discontinuous layers appeared more prevalent in channel and deltaic sands than in marine sands. Based on these initial findings, a detailed investigation was carried out to determine, quantitatively: (1) the degree of continuity of shale breaks in marine. deltaic and channel sands; and (2) the frequency and spatial distribution of discontinuities in the three environments. PROCEDURE The procedure used to obtain field data from outcrops included visual examination, surveying and photographing each outcrop. The photographs were examined carefully and important outcrop features were traced, measured and recorded. The selection of outcrops for this study was made on the basis that each outcrop should be exposed clearly to permit detailed visual examination of vertical lithology. and it should also be sufficiently long (over 200 ft) to provide useful data on the lateral continuity of lithology. Identification of the depositional environment for each outcrop was made on the basis of bedding characteristics, vertical sequence of lithology and the presence of indicative sedimentary features. Whenever possible, hand specimens of associated shales were collected to determine depositional origin. Almost one-half of the outcrops used in this study required environmental identification; the remainder had already been identified by previous investigators. Several photographs of each outcrop were usually required to cover the entire length of the outcrop. These photographs were taken from one station or several, depending on the terrain, size of the outcrop and distance to the outcrop. A Hasselblad camera, with a standard 80-mm lens and a 250-mm telephoto lens, was used. The telephoto lens permitted photographing outcrops as far as two miles away. Slow-speed films were used. either Panatomic-X or Plus-X. The final operation conducted in the field was that of surveying the outcrops. The distance of an outcrop from a point of observation was determined by a triangulation method using the plane table. The measured distance was then combined with the angle of view of the camera lens to establish a scale to be used on the photographs. Films were processed using standard processing techniques and 4.5X enlargements made. The enlargements of each outcrop were butted together to form a single panorama. Slides were also prepared on several outcrops; these were used whenever greater magnification (wall projection) was required to bring out maximum lithologic detail. The shale breaks and bedding planes in each outcrop were traced on transparent acetate film superimposed on

Jan 1, 1966

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By Frank H. Probert

The mining laws relating to winding-ropes in some of the German provinces are very strict, and severe tests have to be periodically made to see that the ropes in use come up to the prescribed standard. A few notes on the method of testing the ropes and the results obtained may be of interest to the members of the Institute. Permission must be given by the Inspector of Mines to put up a winding-plant; and previous to installation a full report made by the manager, clearly setting forth all details of the shaft, the pit-head, engines and appliances appertaining thereto has to be sent to the mining officials. Accompanying each subsequent report, further details, such as the name of the firm supplying the rope, construction, quality of steel, date of installment, weight per meter, length, particulars of the safetycatches, cages, etc., must be given. At least one spare rope must be kept at ever? shaft ready for use in case of emergency. The rope must hang in the shaft, with cage attached, not less than twenty-four hours before it is used for winding; and it must have undergone a severe test in the manner hereafter described. The laws prescribe that when a rope is continually in use it must be tested every three months; but if the rope is only used every few days it must be tested at least every six months, in the presence of the superior officer; and notification of the date of testing has to be sent to the Bergrath two days before the test is made, in order that he can personally superintend the operation if he chooses. Should winding have been stopped for a long time, it is not necessary to test every six months; but before the rope can be used again it must be tested.

Jan 1, 1901

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. TABLE 1 .-Typica.1 Chemica1 Analysis [PER CENT H20,1100F ............................................ 0.0'2 Ignitionloss ............................................. 43.56 MgO .................................................. 19.19 CaO .................................................... 29.07 FezO .................................................... 0.39 A1203 .................................................... 1.94 FezO .................................................... 0.39 A1203 .................................................... 1.94 ..................................................... 5.75 SO2.. .................................................. Tr.] Rock was carried by 12-yd. dump trucks to a 42-in. gyratory crusher set at 6 1/2 in. The product of the primary crusher was taken by a belt conveyor to a double-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1937

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: " ' What device does he bear on his shield?' asked Ivanhoe. 'Something resembling a bar of iron, and a padlock painted blue on a black shield.' 'A fetterlock and shacklebolt azure', said Ivanhoe"-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

By O. W. Ellis

RECENTLY there has been a considerable revival of interest in the effects of the various elements commonly added to brass for the purpose of increasing its strength. For many years the work of Guillet2? alone gave reliable information in this regard. Even today his determination's of the coefficients of equivalence of the various elements relative to zinc in brass are those universally employed in industry. This is so because these coefficients have stood the test of time-their substantial correctness has been proved in almost universal practice. It is not our intention to discuss here these coefficients or their use. Rather do we wish to emphasize the need for further systematic studies of the mechanical properties of the ternary systems of copper, zinc, and other individual elements. Since Guillet published the results of his first investigations Millington,16 Smalley33 and Thibaud45 have added somewhat to our information. In general they have confirmed the findings of Guillet, which may be stated in the following rather general terms: 1. The addition of aluminum to the 70:30 and 60:40 brasses progressively increases their hardness and strength and reduces their ductility and resistance to shock. 2. The addition of small amounts of iron to a 60:40 brass improves its strength without affecting its ductility. 3. The addition of small amounts of manganese to a 60:40 brass causes a progressive increase in its strength and reduction in its ductility. A considerable amount of information has been amassed in regard to the effect of nickel on brass (9, 22, 41) which it is unnecessary to refer to here, in view of the scope of this paper.

Jan 1, 1929

By A. C. Fieldner

ASH in coal has always been regarded as an undesirable substance, as the heat content of a coal decreases in direct proportion to its ash content. It represents so much inert material that has to be transported, handled when the coal is burned, and finally disposed of. W. R. Roberts, in an address before the Engineers' Society of Western Pennsylvania, Pittsburgh, on Sept. 29, 1925, said that on an annual output of five hundred million tons of coal, a reduction of 3 per cent. of ash means fifteen million tons of refuse and a decrease of $30,000,000 in freight charges. Ash also often prevents efficient utilization of the coal through the formation of clinker caused by the melting of the ash constituents when subjected to heat. The mineral constituents of coal may be of such nature as to make the coal unsuited for specific uses, as for instance, high-sulfur coal for making metallurgical coke. While the usual proximate analysis of coal gives the amount of ash, it gives no information as to the nature and composition of the ash nor of the mineral constituents from which the ash is produced. For the efficient washing of coal to remove ash-forming constituents it is desirable to know the composition and distribution of the ash-forming constituents. Obviously such information is also desirable for the most efficient utilization of coal.

Jan 1, 1926

By Y. C. Liu, G. A. Alers, S. S. Choi

In searching for an explanation for the obvious difference between the copper and the brass type of rolling texture, it is common practice to look for correlations with other properties. For example, there are obvious differences between copper and brass in the critical resolved shear stress, the extent of easy glide or stage I, and the amount of "overshooting)) during single-crystal deformation.' Also, the slip lines in copper are fine and wavy while those in brass are more coarse and better described as slip bands.' Since neutron irradiation is known to make these properties in copper change in such a way as to resemble brass,2'3 an excellent test for these possible correlations is to see whether neutron irradiation produces a corresponding change in the texture, i.e., whether irradiated copper develops a brass-type rolling texture. The experiment would also answer the more important question of whether or not lattice defects like those introduced by neutron irradiation have any effect on the development of rolling textures in fcc metals. Experimental studies using conventional X-ray pole figure techniques are inconvenient because the X-ray detection system must be modified to discriminate against the radioactivity which is induced in the specimen by the necessarily long exposure to neutrons. Nevertheless, some texture determinations have been

Jan 1, 1968

By E. F. Steeb, P. C. Rosenthal

BlANKS 8 in. long were cut from the as-received bar stock and austenitized at 1560° F for 1 hr, oil quenched, tempered at 1140°F for 1 hr, and water quenched. The heat-treated blanks were machined into tensile specimens which were subsequently used for the straining operation. Some of the tensile specimens were temper embrittled at 900°F for 24 hr and air cooled prior to or following the straining operation. The specimens were strained in tension up to 5 pct total strain (elastic plus plastic) either at room temperature or at 900°F. The reduced sec- tion of the tensile specimen employed was 5 in. long and 0.600 in. in diam. This size specimen was sufficiently large to permit two standard Charpy impact bars to be machined from it. One group of specimens was temper embrittled at 900°F for 24 hr under stress of about 20,000 psi applied with a hydraulic tensile testing machine. Approximately 0.34 pct plastic strain occurred during this treatment. A comparison of series "A" and "B" data in Table I at 0 pct strain, reveals that the steel was rather highly susceptible to temper embrittlement, the embrittling treatment causing the transition temperature to rise 165°F. The 28 ft-lb level, which was near the center of the sharp-rising portion of the transition curve, was selected as the

Jan 1, 1959

By R. C. Hall

In the present work, experiments determined the effect of the order-disorder reaction near the Fe,Al composition on the magnetic anisotropy and magnetostriction of single crystals: A material which is more difficult to magnetize in one direction than in another is anisotropic, that is, the ease with which ferromagnetic materials may be magnetized in different crystallographic directions determines the anisotropy. Two investigators have estimated the anisotropy of the aluminum iron alloys from poly-crystalline data;1,2 however, these estimates should not be considered to be reliable. Siege1 made two accurate measurements of the first anisotropy constant* from single crystals of 4.0 wt pct aluminum sotropy throughout the ferromagnetic aluminum iron system have been described. These results were obtained from single crystals which were slowly cooled and, hence, ordered near the Fe3Al composition.4 Magnetostriction is the change in length per unit length resulting from applying a magnetic field to a ferromagnetic material. For the purpose of this report, the saturation magnetostriction was measured. This is the maximum change in length per unit length resulting from an applied magnetic field large enough to saturate the material in a given direction. This magnetostriction has been determined for single crystals of the ferromagnetic aluminum-iron system.' The crystals near Fe3Al were also ordered. PREPARATION AND TREATMENT OF SINGLE CRYSTALS Single crystal bars were grown from the melt.' The raw materials for these crystals were iron and aluminum of 99.9 and 99.99 pct purity, respectively. From the bars, crystals in the shape of circular

Jan 1, 1959

By Zay Jeffries

THE object of the present paper is to enlarge somewhat on the general principles advanced in my discussion 1 of Mathewson and Phillips' article on. The Recrystallization of Cold-Worked Alpha Brass on Annealing.2 It will also serve as an acknowledgment of Prof. Howe's3 most important remarks on my contribution. In this paper the writer has adopted Prof. Howe's suggestion to substitute the term "germinative temperature" for "critical temperature for grain growth." Instead of being an exact or certain temperature it should be considered that the germinative temperature phenomenon exists throughout a small temperature range. Factors Influencing Fast Growth Phenomena The development of grains of macroscopic size at the germinative temperature should be considered the extreme condition of a general rule. When considered in this light it is not strange that the development of these large grains should be the exception and not the rule. The principal factors influencing the operation of the laws of fast growth temperature are as follows: 1. Rate of heating.

Jan 10, 1916

By W. Evans, C. E. Ells

The agglomeration of hydrogen in pure aluminum and A1-Mg alloys has been studied through use of hydrogen introduced into the metal by cyclotron proton irradiation. Both the growth and dispersal of the agglomerates have been followed by metal-lographic techniques. During the cyclotron irradiation, agglomeration occurs at temperatures i 100°C for hydrogen concentrations as low as 1 ppm. On heating at elevated temperatures, 300°C to 600°C, intragranular agglomerates first coarsen and then disperse. The agglomerates formed at grain boundaries are much larger than the intragranular agglomerates; with hydrogen concentra- tions > 10 PPm, heating for 1 hr at 500°C results in extensive grain-boundary cracking. The hydrogen agglomerates have been shown to inhibit grain growth, but no inhibition of recrystallization has been observed. The ability of hydrogen to enter aluminum at a free surface, combined with its high-diffusion rate at elevated temperatures, accounts both for growth and dispersal of the agglomerates. Irradiations at elevated temperatures give results consistent with the explanation proposed for agglomerate behavior on post-irradiation heating. 1 HE formation of hydrogen-filled bubbles, or blisters. in aluminum and its alloys has been studied for over' thirty years. The work up to 1952 has been reviewed by Kostron' and since then Ransley and

Jan 1, 1963

By Marius R. Campbell

Every mining engineer who has engaged in prospecting for coal in flat-lying rocks understands the importance of constructing geological sections across the territory which he has to prospect. If the area is small and the time and means at his command are unlimited, he can construct such sections with the transit and level; but if the area is great and the examination hurried, as it frequently is, he will doubtless be puzzled how to proceed. Under this pressure of time and means, his work will probably be, to a great extent, devoid of any system, being simply a hap-hazard opening of such seams as show in outcrop at some point on the territory, without any determination of geologic structure or stratigraphic succession. Prospecting carried on in this manner is never satisfactory to the intelligent mining engineer, for he must realize that the information which he is able to furnish to his employer is totally inadequate to determine the economic value of the property. To the owner of the land such a report is no more satisfactory than to the engineer. Unless the latter can show both

Jan 1, 1897

By J. Poijärvi, J. Rastas

Recently, when increasing attention has been paid to mercury for environmental reasons, the interest of several plants is directed to the removal of mercury from roaster and smelter gases. When Outokumpu Oy built its zinc plant at Kokkola in 1969, intensive development work was started to find an efficient and economic method for mercury removal from roaster gases. A process was developed, after laboratory research and pilot plant tests, to eliminate and completely recover mercury from the roaster gases. The process was commissioned in 1970. The behaviour of mercury in the roasting process and several possible methods of removing it from gases are discussed in this paper. Theoretical investigations and empirical tests show that the removal of elemental mercury from gases by sulphatization is very efficient. Further, it is stated how the technical process was built on this idea. The zinc sulphide concentrates contain small quantities of selenium, chlorine and fluorine. The role of selenium in the process is described. Similarly, the behaviour of chlorine and fluorine in the roasting, sulphatizing and scrubbing units has been discussed. Finally, the recovery of purified mercury and selenium from the precipitates is described.

Jan 1, 1973

By Walter G. Perkins

In the assay of copper-bearing material for gold and silver, the elimination of copper before the final cupellation is of course essential, because any copper left in the lead-button will carry gold into the cupel; and a method which will effectively remove the copper with the smallest amount of manipullation is desirable. The scorification method is often rendered long and tedious by the necessity of repeatedly re-scorifying the button— to say nothing of the risk of losing Au—Ag thereby incurred. An ore carrying, for instance, 10 per cent,. of copper and only 0.1 or 0.2 oz. gold per ton, cannot be scorified with accurate results, because so many portions would have to be taken in order to get enough gold for weighing. On the other hand, the crucible method, with potassic nitrate and nails, would not do at all in such a case, because all the copper would be reduced by the nails, and (if the charge were 0.5 A. T.) this would defeat cupellation, by causing cupel-absorption of gold. In matte-assays, more concentrated value permits the determination of gold from smaller portions, and thus diminishes the difficulty experienced with ores. The method here described has been severely tested, during use for more than a year, and hart never failed hitherto, in the assay of any ore or product to which it has been applied. It is not proposed as perfect for every variety of ore or matte—probably no method would be that; but it is believed that, intelligently used, with the modifications dictated by practice, it will give better results, with less expenditure of time and labor, than any other known to the writer.

Jan 1, 1902

By Francis Rich

BEFORE the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was pro-ducing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3. To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

An educated man is distinguished neither by his clothes nor by his knowledge; he is remarkable not for the things he says, but for the way he says them. You cannot even stand with him under an archway in the rain without finding him out. He may talk only of the weather. His words and his phrases alike my be simple. What distinguishes him is the arrangement of his words; however desultory his talk, it will be methodical; he has habituated himself to foreseeing the part to be played by each word he uses and the place to be taken by each sentence he utters. On the other hand, the uneducated man, though shrewd and well-informed, will relate facts and events as they recur to him, generally in disorder; in his effort to recollect and in his attempt to rectify forgetfulness he will pause irregularly, filling the intervals with meaningless phrases, such as "and then", "and so", or "said he to me", "said I to him"; and even the continuous parts of his story will be told confusedly-because he has not learned the proper use of words.* My own experience as an editor of technical manuscripts has taught me that the misuse of 'that' and 'which' is a fruitful cause of obscurity and confusion. The relative pronouns have distinct functions, and no writer can express himself clearly until he has learned to discriminate between these functions. For example : The engineers who refused to submit were discharged. The engineers, who refused to submit, were discharged. The engineers that refused to submit were discharged.

Jan 1, 1931

By Price E. R.

The coal industry was beset with work stoppages and strikes throughout the year, and there was some loss in markets to oil and gas. These conditions, along with the mild decline in industrial activity, the steel strike, and the reduction in exports, contributed to an unfavorable year for the industry. All coal mines are working three days a week at the time of writing, and in estimating production for the year, it will be assumed that the mines will continue to work on that basis through December. Total production of bituminous coal in 1949 is estimated at 420 million tons, which is 179,518,229 tons under the production in 1948. Anthracite production is expected to reach 39,400,000 tons as compared with 57,139,948 tolls in 1948, a loss of 17,739,948 tons. Coal stocks, as of January 1, 1949, were 69,373,000 tons but at the end of the year will have dropped to approximately 22 million tons. Regardless of the difficulties during the current year, the industry has made substantial

Jan 1, 1950