Search Documents

Jan 1, 1938

Jan 1, 1938

By Y. C. Liu

The orientation relationship between the dejormation and recrystallization textztres of binary Cu-P alloys of high phosphorus content was observed to he a ± 14-deg (110) rotation. According to the ori-ented-gvowth hypothesis, the same relationship should exist between a successfully flowing pain and the strained single-crystal matrix of alloys of corresponding composition. The orientations of thirty successfully growing grains were obtained in a Cu-1.0 at. pct P alloy. Both a conventional analysis and the more detailed analysis advanced in the present study demonstrate that the observed orientation relationship is not comparahle to that predicted by the oriented growth hypothesis. IT has been shown experimentally that the formation of recrystallization textures in metals may be explained on the basis of the oriented-growth hypothesis. This conclusion is based primarily on the results of cooperative experiments carried out by various investigators in aluminum. Beck and HU' suggested that the orientation relationship between the recrystallization and deformation textures of aluminum is a 38-deg(111) rotation. A similar relationship, i.e., a 40-deg(111) rotation, was observed between the primary and secondary recrys-tallization textures.' Since the secondary grains result from a process of selective growth, this naturally implies that the same mechanism is also responsible for the formation of the primary re-crystallization texture from the deformed matrix. Further evidence was provided by the experiments of Liebmann, Liicke, and Massing3 and Yoshida, Liebmann, and Lucke.4 They observed that grains which could successfully grow into strained aluminum single crystals invariably exhibited the same orientation relationships with their matrix. Thus, regardless of other opinions,5'9 these results offered good evidence in favor of the oriented-growth hypothesis. In order to examine broader applications of this oriented-growth hypothesis, experiments should be carried out in metals other than aluminum. In a recent investigation on the recrystallization textures of binary copper alloys with phosphorus, arsenic, and antimony,7 it was found that the predominant recrystallization components were related to the deformation textures by a (110) rotation. The (110) rotational relationship is different from the (111) relationship generally proposed between the recrystallization and deformation components of other binary copper alloys. 1,8,9 Applying the observations made for aluminum, the oriented-growth hypothesis predicts that the orientation relationship of grains successfully growing into the strained single crystals of either one of these copper alloys should correspond to that observed in the textural study. Verification of this prediction would provide a critical test of general applicability of the oriented-growth hypothesis to the formation of recrystallization textures in fcc metals other than aluminum. The Cu-1.0 at. pct P alloy was selected in the

Jan 1, 1964

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN : Submitted herewith are the report of the Treasurer for the year 1944 and reports for the same year of the following standing committees: Membership, Ad- missions, Papers and Publications, MIN- ING AND METALLURGY (Magazine), and Library. To these reports you are referred for additional details.

Jan 1, 1946

By A. Gemperle

Electron diffraction and transmission electron microscopy on foils at room temperature were used to investigate the ordering of Fe-Si alloys containing 10 to 23 at. pct Si. A certain degree of DO3 order was found in all alloys. With the exception of the lowest silicon concentration for which the antiphase domains could not be clearly resolved, the alloys have a domain structure of two-domain type with boundaries having 1/4a01<111> displacement vectors for less than 12.3 at. pct Si and with boundaries having 1/2 a0<100> displacement vectors for more than 12.3 at. pct Si. The alloys with 12.3 at. pct Si have a domain structure consisting of fine domains with 1/2a&apos;o<100> boundaries within much larger domains with 1/4a&apos;o<111> boundaries. The development of these structures can be explained by transition of the alloy from the disordered state into the B2-type order and then into the D03-type order by the mechanism proposed previously for the FeSAl alloys. The existence of the B2 structure in the lower part of the investigated concentration range reported in some articles can be explained by fine domains with 1/2a&apos;o<100> boundaries formed by several disordered planes within large domains with 1/4a&apos;o<111> boundaries. The ordered structure predicted by the theory —with practically no domain boundaries —is found in the alloys having 12.3 at. pct Si where it develops in the B2 structure region. ORDERING in Fe-Si alloys was first studied by phragmenl who found that beginning with 13 at. pct Si the DO3 (Fe3Si) superlattice reflections appear in the diffraction patterns. The equilibrium diagrams constructed later by corson2 and Haughton3 from various measurements proposed the existence of a homogeneous solid solution (a phase) in the range from 0 to 25 at. pct Si. Jette and Greiner4 and Farquhar et al.5 measured the relation between lattice parameter and composition and they considered the break in the curve at 9 to 10 at. pct Si to be caused by the ordered solution a"(Fe3Si). Glaser and Ivanick6 Determined critical ordering temperatures of the alloys containing from 10.9 to 27.9 at. pct Si from the measurement of the electric resistivity of quenched samples. In all cases the critical temperature was lower than the melting point and it was highest for 25 at. pct Si. Lihl and Ebel7 measured the lattice parameter curves at various temperatures up to 1000°C. The region between two breaks on these curves, corresponding to 10 to 12.5 at. pct Si at room temperature, was considered by them to be two-phase (a + a"). They concluded by extrapolation of the measured values that a" in the alloy having 25 at. pct Si is stable up to the melting point. Davies8 studied superlattice reflections in the X-ray diffraction patterns of an alloy containing 8.7 at. pct Si. He found the B2 structure and short-range order in the slowly cooled samples and the DO3 A. GEMPERLE is Research Scientist, Institute of PhysicS, Czechoslovak Academy of Sciences, Prague, Czechoslovakia. __Manuscript submitted January 2, 1968. IMD structure in the quenched and annealed samples. This investigation first reports the presence of the B2 structure, phase a&apos;: in Fe-Si alloys. Meinhardt and krisement9,10 also found its existence in Fe-Si alloys by neutron diffraction. No order was detected by them in the alloy containing 8 at. pct Si. The onset of B2 order was observed at a composition of 9.2 at. pct Si. They found almost perfect B2-type order with partial DO3-type order at room temperature in the 10 to 12.5 at. pct Si range and almost perfect DO3-type order in the 12.5 to 25 at. pct Si range. They established the critical temperatures Tc of both the structures through measurement at higher temperatures. The critical temperature for the B2 structure was found to be always higher than the critical temperature for the DO3 structure of the same alloy. They extrapolated the curves of the critical temperatures and concluded that the alloys with more than 17 at. pct Si have the B2 structure up to the melting point and the alloys with more than 23 at. pct Si have the DO3 structure up to the melting point. The results of Meinhardt and krisement9,10 were confirmed by Dokken&apos;s measurement" of the temperature dependence of the electrical resistivity in the 10.8 to 15 at. pct Si range. On the other hand chessin12 detected by X-ray diffraction a considerably lower degree of order in the 12.7 at. pct Si alloy. ANTIPHASE DOMAIN STRUCTURE IN ALLOYS WITH B2- AND DO$-TYPE ORDER The ordered structures B2 and DO3 can be described in terms of a subdivision of the bcc lattice into four fcc sublattices with a parameter double that of the bcc lattice. Following Marcinkowski13 we will label them I. 11, 111, IV. The B2 structure in the AB alloy is formed by placing A atoms on sublattices I and II and B atoms on sublattices III and IV. In a non-stoichiometric perfectly ordered alloy having concentration (A) > (B), A atoms occupy sublattices I and 11. and A and B atoms distributed at random occupy sublattices III and IV. The DO3 structure in an A3B alloy is formed by placing A atoms on sublattices I, 11, and 111, and B atoms on sublattice IV. In a nonstoichiometric, perfectly ordered alloy having concentration (A)/3 > (B), A atoms occupy sublattices I, 11, and 111, and A and B atoms distributed at random occupy sublattice IV. As further shown in Ref. 13, two types of domains are possible in the B2 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4 a&apos;o<ll1> only. Four types of domains are possible in the DO3 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4a&apos;o<111> and 1/2a&apos;o<l00>. Bethe14 suggested on the basis of theoretical considerations that in a structure with two sublattices at low temperatures only one domain should be present in the whole crystal at equilibrium. Similarly Bragg15 concluded that at low temperatures the domain struc-

Jan 1, 1969

By John V. Beall

Beall: Mr. Bennett, you have had a very successful -and a very colorful-career in mining. Would you tell us about your first job in the mining industry? Bennett: I was a mine surveyor on the Mesabi and Marquette ranges, working both open pit and underground. I worked two years for the Meriden Engineering Co., formerly the Meriden Iron Co., which was founded in 1904 to operate mines and to act as a lessors&apos; agent for inspection. At the time I was there, Meriden was operating one open pit and one underground mine, and acting as agent or inspector for some lessors, the owners of the fee interest.

Jan 1, 1968

By H. Bernstein

Grain coarsening tests were carried out on AI-4.5 pct Cu and AI-4.5 pct Si alloys. The effects of three variables, melt composition, pour temperature, and mold temperature, were determined. It was found that the macrostructure generally coarsened with increased pour and mold temperatures. Coarsening was extreme in the unrefined alloys but was retarded by the active grain refiners like titanium and columbium. The effect of boron was spectacular in suppressing coarsening tendencies. The results of the investigation support the carbide theory of nucleation as opposed to the peritectic theory. A REVIEW of prior work on the subject of grain refinement in the light metals indicated that, for the most part, it had been concerned with the positive effects of addition agents upon structure. This work produced various theories of refinement. Prominent among them were the peritectic theory and the transition element carbide theory. Certain inadequacies in the former theory appeared to be explained satisfactorily by the transition element carbide theory. In order to appraise these theories further, a study was undertaken of the permanence of grain refinement effects when subjected to thermal or chemical variations. It was considered that a study of this kind would be of practical value, since the light metals are exposed to thermal and chemical variations in the normal course of foundry operations. Accordingly, two alloys of commercial importance were selected for this investigation, the A1-Cu and A1-Si alloys. Experimental Procedure and Results Raw Materials: The base alloys, A1-Cu and A1-Si, were prepared from virgin aluminum and hardeners, induction melted, and pigged for remelting. The grain refiners, including titanium, columbium, zirconium, and boron, were added as master alloys. Analyses of the raw materials and base alloys are listed in Table I. Melting and Casting Practice: The metals were melted in clay-graphite crucibles in a Hevi-Duty pit-type resistance furnace, equipped with a Leeds and Northrup Micromax Recorder and Controller. After melt down of the base alloys, the additions were made. For each casting, approximately 80 grams of metal were poured into a preheated graphite mold held in a transite flask. The mold (Fig. 1) weighed 320 grams. To determine the effect of superheat upon structure, a set of melts was heated successively to four temperature levels, 705°, 775°, 845°, and 915°C, and test specimens were cast at each level. Prior to each pour, the furnace temperature was held constant for 20 min. Next, a set of melts was put through a superheat cycle and test specimens were cast at melt temperatures of 705" and 915°C successively. The crucibles then were cooled in air to 705°C as deter-mined by immersion thermocouple and additional test specimens were poured. The cooling interval was approximately 1 min. Another set of melts was furnace cooled with the cover slightly ajar and test specimens cast as before. The interval in this case was 15 to 20 min, varying with the superheat temperature. The mold temperature for all these tests was 400°C. To determine the effect of cooling rate without superheat upon structure, a set of melts was heated to 705°C, and castings were poured at mold temperatures of 205", 400°, and 540°C. An interval of 15 min elapsed between each pour. Mold temperatures were measured by a direct reading millivolt-meter, using a chromel-alumel thermocouple located at midwall thickness of the mold. To demonstrate the phenomenon of chemical coarsening, agents such as chromium and beryllium, which had acted as coarseners in a previous investigation,&apos; were added to the A1-Cu alloy. Test speci-

Jan 1, 1955

By H. M. Myers, J. E. Funk

The two-phase flow of a drilling fluid in a diamond drill bit is investigated by deriving and solving the steady-state continuity and momentum equations. Parameters in this analysis are rotational speed of the bit, local rate of addition of drill solids, non-Newtonian nature of the drilling fluid and drilling rate. The describing equations relate the flow and pressure drop to the design characteristics of the bit. The equations are integrated numerically yielding the flow-rate pressure drop characteristics for the bit, flow distribution in the bit and velocity and static pressure as a function of position in each flow channel of the bit. Results are presented for a particular bit design. This paper shows that under normal drilling conditions certain parameters may be neglected in the hydraulic calculations for a diamond drill bit. Therefore, shortened forms of the equations presented can be used to fit the proper diamond bit to the drilling fluid hydraulic system. INTRODUCTION Like the conventional bit, the diamond drill bit is a key component in the circulating system of a well. The conventional rock bit is fitted to the circulating system by selecting the flow nozzles which provide the system with the proper flow-rate pressure drop relationship. Fluid behavior across the face of the diamond bit must be better understood so the bit can also be fitted to the circulating system. Data from field-operated diamond bits are presently available and do yield some information regarding the flow-rate pressure drop relationship. However, the number of factors affecting this relationship is quite large. Drilling parameters and conditions such as bit penetration rate, bit weight and rotational speed are important. Moreover, flow channels in the bit are part of the cutting head, and introducing drilled solids into the flow channels reduces the flow area, causes additional drag and influences the pressure drop. Many tests would have to be performed if field tests were required to study all parameters which might influence fluid behavior in the bit. A logical approach to this problem is to investigate analytically the fluid behavior in the bit, including parameters that are present under normal drilling operations. This approach, which seems to offer the best method for future studies, is presented in this paper. Following is the general procedure. 1. Equations describing the most general flow channel are written and include the addition of drilling solids (which is related to penetration rate), rotation of the bit, design parameters of the bit and non-Newtonian properties of the fluid. 2. A typical bit is designed and the bit parameters are substituted into the equations. 3. Parameters are assumed (penetration rate, rotational speed of the bit, mud weight, etc.). 4. The describing equations are numerically integrated to obtain the pressure drop across the face of the bit as a function of flow rate. 5. The pressure-drop contribution of each component (friction, acceleration, etc.) is obtained from the numerical solution, and those factors which largely influence the total pressure drop are identified. Classifying the drilling fluid is important in establishing the friction factor relationship since the frictional pressure losses are the main contributors to the total pressure drop. High-density drilling fluid is commonly assumed to be a Bingham plastic. 1-3 Govier4 presented a method for selecting a friction factor in the laminar flow region from the rheology properties of the mud and a modified Reynolds number. Metzner5 presented a criterion for selecting the friction factor in the turbulent flow region. The bit design used in conjunction with the solution of the equations has divergent flow channels. Stall, which is the backflow of fluid in the channels due to eddies that occur on the outer perimeter of the flow stream, can occur in these divergent channels (or diffusers). When stall does occur the static

By T. M. Kegley, J. H. Frye, D. L. McElroy, M. L. Picklesimer, E. E. Stansbury

Measurements of rate of growth, thermodymmic quantities, and partitioning of Mn are reported for high-purity eutectoid Fe-C and Fe-C-Mn steels for the auistenite-pearlite reaction. Evaluztion of the cotnstants of a derived-rate equation with these data indicate that Mn additions cause the decrease observed by increasivg the activation energy and apparent activation entropy or the movenment of complexes at the interface. A diffusion-controlled mechanism is not required. Appreciable partitioning of Mn to cementite occurs entirely behind the austenite-pearlite interface for more than 30°C of subcooling. ThE growth of pearlite from austenite has been extensively studied over a period of years. but the rate-controlling step in the process is not known nor is the mechanisrn of the effect of alloying elements understood. A comprehensive review of the subject has been given by Mehl and Hagel. The present study has been concerned with further considerations of the effects of alloying elements on the rate of growth of pearlite. Analytical relatioriships for the rate of growth of pearlite have been considered by Zener.2 Turnbull,3 Machlin,4 Cahn.5 Frye,6 and Frye et a1.7 The derived expressions in each case involve the free energy of the transformation. the interlamellar spacing. and some rate term of the nature of the diffusion coefficient. mobility or frequency of occurrence of some rate-determining step. The treatments. of course. differ in detail. Further consideration is given in the present paper to the equation of Frye, Stansbury. and McElroy which was derived from modified absolute rate theory without in any way specifying the mechanism of the reaction. This equation is r=c ? T ? F exp -?E*/RT [1] where r = rate of growth in mm/sec c = a constant AT = equilibrium transformation temperature minus actual transformation temperature "C ?F = free energy per mol of austenite minus that of pearlite ?E* = activation energy R= gas constant ?F in Eq. [1] is computed from the following: ?F=?H?T/To - ?T&apos; dT&apos; ?T&apos; ?CdT"/T" [2] To To where AH is the enthalpy per mol of austenite minus that of pearlite at the equilibrium temperature, To, and AC is the difference in specific heat between austenite and pearlite per mol. Subsequently, Darken, Fisher, and Galligan8 have reported that a layer of ferrite separates pearlite from austenite at the growing interface (i,e., the advancing face of Fe3C is in contact with ferrite, not austenite) and the ratio of the thickness of this layer to the spacing of the pearlite has not been found to vary with alloy content or transformation temperature. This observation does not require any alteration in the above equation: however, it may require that a different significance be attached to the factor, AT. The AT term appears in Eq. [I] as a consequence of a factor for the amount of growth per complex transformed at the interface.* It is based *This is not the sole reason for expecting such a relationship. See Ref. 7._______________________________________________________ on a l/2 ?T dependence of the interlamellar spacing. Zener2 has developed a theory which leads to Soa 1/?V where So = the pearlite interlamellar spacing. This relation is as consistent with the data on interlamellar spacing as other relationships, although, as pointed out by Mehl and Hagel,1 the data are not sufficiently precise to consider the relationship as confirmed. The work of Darken, Fisher, and Galligan8 requires that the above be written where f = the thickness of ferrite layer between austenite and pearlite. The present paper is concerned with iron-carbon-manganese eutectoid alloys and reports experimental measurements of the following kinds: 1) the effect of

Jan 1, 1961

By W. R. Wilcox

The camphor-anthracene system was chosen as a transparent low-melting analog of the zirconium carbide -graphite system. Camphor and zirconium car -bide both grow nonfaceted, while casting of mixtures yields platelets of both anthracene and graphite. Zone melting of thin layers of organic was observed under the microscope. Irregular lamellar structures were produced at high values of the ratio of the temperature gradient G to the zoning rate V. The anthracene invariably led the camphor, indicating lower kinetic undercooling for the anthracene. The lamellar spacing was an order of magnitude greater than typical spacings for metal eutectic systems. Exact behavior depended on orientation of the anthracene. Oriented dendritic structures were produced at low values of G/V. Transient and oscillatory behavior were also observed—much of it unexpected. A.RC-CAST refractory carbide-graphite mixtures are promising thermal-shock resistant materials. Oriented structures of these materials would be superior to arc-cast materials for many applications. Mollard and Flemings1 and Cline2 have shown that aligned structures can be obtained for a wide range of Pb-Sn alloys. However, these metals both solidify in a nonfaceted manner while graphite yields platelets or flakes. In addition only small diameter samples of Pb-Sn alloys were produced because it was necessary to avoid free convection and to have high temperature gradients. The purpose of the present work was twofold: 1) To observe the solidification of a transparent low-melting analog of carbide-graphite systems and 2) to see if larger diameter samples can be produced. EXPERIMENTAL PROCEDURE When zirconium carbide-graphite mixtures are cast, the resulting structure naturally depends on composition. Carbide-rich mixtures yield metal-like nonfaceted carbide dendrites in a eutectic matrix. Graphite-rich alloys have graphite platelets in a eutectic matrix. Empirically it was found that camphor-anthracene mixtures produce similar structures with camphor being nonfaceted and anthracene forming plates. The organic eutectic melted at 116°C and was composed of 78 wt pet camphor.3 The camphor used was U.S.P. grade from Fisher Scientific Company; the anthracene was 98+ pet fro Aldrich Chemical Co. The impurity content is judged to be on the order of 1 pet. Mixtures ranging from 50 to 88 wt pet camphor were employed for the experiments. All but one of the experiments were performed on the microscope-stage zone melting apparatus described in detail elsewhere.4 The organic mixtures were contained in horizontal cells made of microscope slides or cover glasses. In most of the cells the organic was present as a very thin layer, thus giving almost two-dimensional growth behavior. The cells were moved slowly under a heated wire, which caused a molten zone to move through the solid at rates ranging from 0.01 to 5.4 cm per hr. The temperature gradient was estimated before moving the zone by measuring the distance between the line where all solid was melted (freezing point) and that where solid first began to melt (eutectic temperature). The temperature gradient was found to be 465°C per cm in the thinnest cells used, which were made by pressing together two microscope cover slips in the organic melt and then rapidly withdrawing them. RESULTS The experimental results are described in four parts: simultaneous growth, dendritic growth, irregular growth, and transients and erratic phenomena. Steady state data are summarized in Fig. 1. Except where noted all comments are for the cells containing a thin layer of organic. A) Simultaneous Growth. Simultaneous and roughly parallel growth of anthracene and camphor was obtained over the full range of compositions investi-

Jan 1, 1970

By R. J. Stokes

This paper compares the room-temperature mechanical behavior of magnesium oxide crystals containing &apos;fresh&apos; and &apos;grown in&apos; sources. &apos;Fresh&apos; dislocation sources introduced by cleavage or mechanical contact move and multiply to generate slip bands at 3000 psi. Macroscopically the crystals yield smoothly at 6000 psi and can be quite ductile. When &apos;fresh&apos; sources are eliminated by chemical polishing the crystals have to rely on &apos;grown in&apos; sources to initiate slip. They then deform elastically up to extremely high stresses (-30 to 50,000 psi) yielding with a sharp stress drop down to the level at which Ifresh&apos; sources operate. Grown in&apos; sources are considered to be associated with impurity wecipitate particles or inclusions. Annealing crystals at 2000°C dissolves these particles thereby eliminating sources for slip. The crystals then become consistently stronger (> 70,000 psi) approaching within 1/10 of the theoretical strength. Dislocations of the grown-in network do not move under stress to nucleate slip. It is proposed that they are locked electrostatically. DISLOCATIONS were originally conceived to resolve the large discrepency between the theoretical and real strength of solids. The idea that slip propagates by the movement of dislocations is now well confirmed both by electron transmission and etch pit studies. But this by itself is not sufficient to explain the low yield strength of crystals for there is still the need to understand where slip dislocations originally come from. Theoretical estimates place the stress to generate dislocations homogeneously in the lattice at approximately 1/30 of the shear modulus,&apos; a value 104 to 105 times greater than the stress at which the very first manifestations of plastic deformation have been observed. Only an special cases can the theoretical strength be approached; in crystals of high perfection such as whiskers2 where dislocation sources do not preexist and in covalent crystals where the dislocations present at room temperature are almost completely immobilized by the bond character of the solid.3,4 For the most part it is necessary to assume that the yield strength of ionic and metallic solids corresponds to the motivation and multiplication of dislocation sources present beforehand. The question as to their origin appeared to be answered by the suggestion of Frank and Read5 that dislocations forming part of the grown-in structure could operate as a mill for the large scale production of dislocations. The Frank-Read mechanism is still widely accepted as the source of dislocations but a number of observations have been reported which are in serious disagreement with it. One of the most intriguing of these is that under normal testing conditions dislocations of the grown-in network appear to play no role in the plastic deformation of rock salt structure ionic solids. This was first reported in the etch pit studies on lithium fluoride by Gilman and Johnston6 and is true also for magnesium oxide. To explain the comparatively low yield stress of lithium fluoride it was proposed by a number of authors7,9 that small unresolved prismatic loops formed by vacancy condensation were acting either directly or indirectly as the dislocation sources. This proposal led Gilman10 to perform a series of detailed and careful experiments on lithium fluoride to try to identify the sources responsible for the initiation of slip. He concluded that prismatic loops played no general role and that other sources were more important. Dislocation sources in ionic crystals can be divided into two general categories. First, there

Jan 1, 1962

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man&apos;s thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life&apos;s work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe&apos;s pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe&apos;s work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book&apos; on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe&apos;s ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man&apos;s thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life&apos;s work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe&apos;s pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe&apos;s work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book&apos; on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe&apos;s ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By Orville Lyons

CENTRIFUGAL force has been utilized for the dewatering of fine coal for over 50 years by means of machines commonly called centrifugal dryers. In any centrifuge the coal and water are subjected to a spinning action which usually increases in intensity as the coal progresses through the machine. This spinning action, or the centrifugal force that it induces, tears water away from coal particles and produces a dewatered coal. The effectiveness of the dewatering action for any particular machine is governed by the size-consist of the coal and the centrifugal force imparted to the water on the coal.

Jan 5, 1951

By James F. Lewis

The death of Josephus Flavius Holloway, for twenty-one years an active and beloved member, and twice a Vice-President, of the Institute, cannot be allowed to pass without some expression on the part of his brethren of mingled grief and gratitude—grief that we have lost his genial and inspiring presence ; gratitude that we have been privileged to know one who lived " To make the world within his reach Somewhat the better for his being, And gladder for his human speech." The present sketch of his career and character is offered as a sincere, though inadequate, expression of these feelings. Mr. Holloway&apos;s father, Joseph T. Holloway, born, in 1796, in Sunbury, Pa., and yielding in his youthful prime to the prevailing impulse of his generation, started alone, with knapsack

Jan 1, 1897

By D. O. Rausch

The economic relationship between steepening slopes and decreasing waste removal requirements ahead of ore mining is one of the most important factors in the design of open-pit mines. The steepness and stability of the pit slopes often spells the difference between ore and waste profit or loss in low cost open-pit operations. Unfortunately, the technology necessary for designing stable rock slopes is still in the early stages of development. Past and current pit-design methods have been, and still are, empirical, with rock slopes frequently made too steep or too shallow. As such, large expenditures are often made for correcting slopes after failures occur, or for unnecessarily removing more waste material than required.

Jan 6, 1965

By Thomas M. Chatard

Every one engaged in the mining of phosphates is well aware that the price he gets for his product depends upon tile results of chemical analysis. He knows that the value rises with the percentage of phosphoric acid, whether stated as such or as so-called " bone phosphate," and that deductions are made for certain constituents, such as alumina or oxide of iron, when the amount of these exceeds certain limits. The reason for these deductions is but vaguely understood by many, and there are few who possess the special knowledge required to form a competent judgment, either as to the reli-

Jan 1, 1893

By C. J. Leith

A study of the effect of rock composition, rock structure and degree of weathering on the stability of cut slopes is being sponsored jointly by the U.S. Bureau of Public Roads and the North Carolina Highway Commission. In 58 mountain and piedmont counties of North Carolina the percentage of failed cut slopes is greatest in micaceous metasediments, gneisses, and schists, and in saprolite and soil derived from these rock types. Soil slope failures outnumber rock slope failures by two to one. Joints and similar planes of separation exert a strong influence on size and shape of the sliding mass. They may or may not act as failure surfaces, depending on their orientation with respect to the active forces. Climatological data, though indicative of weathering conditions, do not correlate well with slope failure frequency. Because of the presence of joints and similar planes of weakness in soil and rock materials, conventional methods for analyzing slope stabilities are not directly applicable. Empirically derived modifications of these methods are being investigated. A study of the stability of highway cut slopes, sponsored by the U. S. Bureau of Public Roads and the North Carolina State Highway Commission, began in 1962 at North Carolina State of the University of North Carolina at Raleigh. As part of this study all slides, rockfalls and other types of cut slope failures on Federal and State highways in the 58 mountain and piedmont counties in North Carolina were located and described, and the data catalogued in a punched card file system. A major objective of the project is to relate slope failures to properties and physical conditions of the geological units in which the slopes were constructed, and to correlate soil type and/or geological unit with type and frequency of slope failure. The complexities of the problem of slope stability and the limitations which these complexities impose on methods for analyzing slopes have been recognized for many years. A great variety of factors and processes may lead to slides, often making it almost impossible to analyze theoretically the conditions required for stability of slopes. One of the principal factors determining maximum safe slopes is the shear strength of the material in which the slopes are cut, but unfortunately there are very few data available concerning shear strengths of residual soils. Vargasl tested clay derived from gneiss and granite in southern Brazil; the properties of decomposed granite occurring near Hong Kong were determined by Lumb.2 These data are being used, when applicable, to supplement the test data obtained in the present study by Yorke.3 The locations of the North Carolina slope failures, more than 400 in number, are shown on Fig. 1. This map, adapted from the Geological Map of North Carolina,4 suggests the possibility of a relationship between frequency of slide occurrence and rock type. However, the evaluation of this possibility requires consideration not only of the type of rock, but also of its large and small scale structural features, its susceptibility to and degree of weathering, and the composition and structure of the weathering products. Soil slope failures in thoroughly weathered soil material and saprolite outnumber rock slope failures two to one. INFLUENCE OF ROCK TYPE The agricultural soil type involved in each soil slope failure was identified and each failure was catalogued in terms of the parent material from which the soil was derived. These data indicate that most of the slope failures, whether in the rock or in the derived soil, are associated with metamorphic rocks (see Fig. 2a). The data may be skewed somewhat because of the relative sizes of the total areas underlain by the various rock types, but Leith and Gupton5 have demonstrated that the preponderance of failures in metamorphic rocks is of much greater magnitude than could be accounted for by the areal factor alone. The dominance of metamorphic rocks is emphasized when soil slope failures are considered in terms of the specific rock types from which the soils were derived (see Fig. 2b). In particular, mica schists and mica gneisses account for more slides

Jan 1, 1965

By P. Shahinian, M. R. Achter

In a comparison of the creep -rupture properties of nickel in air arid in vacuum there is a reversal in relative strengths with variations in stress. At low stresses the properties are better in air while at high stresses they are better in vacuum. In the early stages of creep in a high stress test the specimen in air nzay have the lower creep rate but the one in vacuum is creeping at a lower rate in the later stages. A mechanism, involving two competing processes in terms of oxidation strengthening and weakening by surface-energy reduction, is proposed to explain these reversals. It had generally been assumed that, relative to their properties in air, the high-temperature strengths of metals would be increased in an inert atmosphere as a result of the elimination of the deteriorating effects of oxidation. However, several recent investigations have shown that the creep strength may be greater in air than in nonoxidizing gases. Pickus and Parker1 found that the creep rate of nickel was lower in air than in hydrogen or nitrogen. Internal oxidation was mentioned by Shepard and Schalliol as a possible cause for the longer creep life of Hastelloy C in air than in vacuum or helium. Sweetland and Parker, who observed lower creep rates for aluminum and copper in air than in helium, discuss the possible applicability of the dislocation-barrier mechanism to explain their results. Surface oxide layers may interfere with the escape of dislocations through the surface or with their generation there. In addition to showing the strengthening in air of low-alloy and stainless steel, and nickel and cobalt-base alloys, shahinian4 presented notch-effect data which indicate the role of stress concentrations; alloys of relatively low ductility were more sensitive to atmosphere strengthening when notched specimens were used. Although Bleakney&apos;s copper wires had a lower reduction of area in air than in vacuum, it is difficult to interpret his results in terms of strength changes since the stresses employed were not measured. In contrast to these data showing the strengthening in air, a number of investigations, most at relatively low temperatures, have demonstrated that the environment may cause a decrease in strength. These results are generally explained in terms of the effect of environment on surface energy. In a review of the subject, Benedicks and Harden use the concept of atomic bonding to explain how the adsorption of impurities would decrease the energy of a clean surface. A decrease in surface energy would facilitate the propagation of cracks or extension of the surface. Use of this mechanism is made by sato7 to explain the weakening of steel specimens bent in various liquids, by Potek and Shcheglakovs for the reduction of fracture strength of steel in molten metal, and by Benedicks and Harden for the reduction of strength of a variety of materials in a number of liquids. A similar explanation might be used for the results of Forestier and Clauss. The fracture stress of fine wires pulled in a variety of gases, including air, is lower than in vacuum. They attributed their results to the "tendency" for the gases to condense on the metal surface. That the strength of metals is affected by the type of gas in which the test is conducted has been demonstrated convincingly; the mechanism of the effect, however, is still uncertain. This investigation represents one in a series to explore the influence of variations in alloy composition and test conditions on the atmosphere effect in the expectation that the results would afford an insight into the processes taking place. To determine the effect of specimen composition, the present investigation was conducted

Jan 1, 1960

By N. K. Chen, R. Maddin

THE textures of straight-rolled and of cross-rolled molybdenum were first determined with the aid of pole figures by Custers and Riemersma.&apos; These authors have shown that for straight-rolling, the main texture was (100) [0111 with a considerable spread about the rolling direction. After cross-rolling a second texture was obtained in which there was a [111] axis perpendicular to the rolling plane, possessing a rotary symmetry. Recently Semchy-shen and Timmons2 in their study of preferred orientation of arc-cast molybdenum sheet obtained similar pole figures. In these two investigations, polycrystalline materials were used. In the main, the textures of molybdenum in these cases are qualitatively consistent with rolling textures of other body-centered cubic metals, such as iron and Fe-Si alloys." In the present investigation, single crystals of molybdenum were deformed by rolling with respect to specific crystallographic planes and directions. Since the deformation textures of polycrystalline aggregates have been related intimately to the behavior of individual grains,4 a study of possible correlations of final textures with respect to the initial orientations of the single crystals might conceivably lead to a better understanding of the textures. Annealing treatments were carried out after deformation in order to study the recrystallization characteristics as well as the recrystallization texture. Rolling of Single Crystals Single crystals of molybdenum (about 1/8 in. in diarn x 1-in. long), grown by the method previously described,5 were cold-rolled without intermediate anneals. Except for specimens MR-1 and MR-2, which were rolled at random in the preliminary test in order to find a proper rate of reduction, all other specimens were carefully documented as to their respective orientation before deformation by means of X-ray Laue back-reflection methods. A stereo-graphic projection was constructed from which it was possible to determine a particular plane and direction to be considered for rolling. Parallel flat surfaces were then polished metallographically with respect to a reference scratch on the specimen which was mounted in sealing wax. These flat surfaces contained the plane chosen for rolling. After etching, a Laue back-reflection photogram was again made of one of the flat surfaces to determine the exact plane of rolling. The initial orientations of all the specimens (specified by two elements for each crystal, direction of rolling and the pole of the rolling plane) are summarized in Fig. 1. The specimens were mounted in plasticene between two hardened Si-Fe plates. The sandwich was then rolled down, keeping the direction constant in the case of straight-rolling. In cross-rolling (MR-10, MR-11, and MR-12) the sandwich was rotated 90" after each pass so that every first and third pass contained the same rolling direction. Specimens MR-14, MR-15, and MR-16 were compression-rolled following the manner of Barrett." In these cases the direction of the sandwich through the rolls was changed by 3" to 5" for each pass until the specimens were rolled to the desired reduction in thickness. It was found that if extreme care was exercised in rolling, i. e., the amount of deformation per pass was extremely small, the specimens could be rolled to a large reduction in thickness. The rate of reduction used, with a single exception of MR-1. was generally 0.001 in. per 10 passes. Thus, it took about 800 passes to reduce a specimen to a final reduction in thickness of 87 to 98 pct. The results of rolling are shown in Table I. Cold-Rolling Textures The final orientations were determined by the conventional Laue transmission method," using molybdenum radiation, with or without a zirconium filter. Pole figures were plotted from (1101 and (200) reflections in which three degrees of intensity— heavy, medium, and light—were determined visually. Three main types of textures have been observed from the deformed single crystals. These are: 1—a

Jan 1, 1954