Search Documents

By E. H. Edwards, J. Washburn

Zinc crystals were deformed in simple shear and it was found that anisotropic strain hardening occurred in which the inactive slip systems were hardened more than the active system. The formation of dislocation barriers by dislocation interaction was discussed as a possible explanation of the hardening of the latent systems. STRAIN hardening which accompanies slip in a metal crystal is not limited to the slip systems actively contributing to the plastic strain. There is also a strengthening of the latent slip systems which are crystallographically equivalent to the active system. In the case of aluminum deformed in tension, Taylor and Elam1 found that plastic flow on one set of octahedral planes caused either the same or a slightly greater hardening on an inactive set. Similar results have been obtained for crystals of a brass2 and of Cu-A1 solid solutions.3 Experiments by Rohm and Kochendorfer4 indicated that the hardening of the active system exceeded the hardening of any latent system for aluminum crystals deformed in shear. On the other hand, strain hardening in zinc and cadmium crystals tested in simple shear at —196°C was recently found to be greater in the latent than in the active slip direction." When the strain direction was shifted during testing to a direction 60" from the original, a higher stress was required for glide to continue than would have been needed for flow to proceed in the original direction. The relation between the hardening of active and latent systems must be complex, depending upon the relative orientations of the systems and upon the experimental techniques used to deform the crystal. A detailed knowledge of the hardening produced in latent systems would be valuable in choosing between possible dislocation models of the strain-hardening process. The experimental data now available are incomplete and even contradictory. The present study was undertaken to provide quantitative information regarding the relative amount of hardening of active and latent systems for a particularly simple case. Zinc crystals were deformed in simple shear along one of the three crystallographically equivalent directions [250], [1210], and [1120] in the slip plane, and the relative hardening produced in each of these directions was compared. Experimental Procedure and Results The single crystals of 99.99 pct purity zinc used in this investigation were grown from the melt in the form of 1 in. diam spheres. Shear specimens were acid-machined from the crystals by a method which has been described previously. The gage section of the test specimen was a cylinder having a height of 1/8 in. and a cross-sectional area of approximately 1/3 sq in. All specimens were machined with the axis of this cylindrical gage section aligned with the [0001] axis of the crystal. An innovation in the design of the shearing apparatus for these tests was the provision for a rapid shift in the direction of the applied stress from one slip direction to any other slip direction lying in the same slip plane. Fig. 1 shows a section through the specimen and shearing apparatus, and Fig. 2 is a

Jan 1, 1955

By Nicholas J. Grant, Noboru Komatsu

Metallographic and X-ray studies were made of oxide dispersion strengthened Cu-12 vol pet SiO2 and Cu-3.5 vol pet Al2O3 alloys following time exposures at temperatures approaching the melting. point of the matrix metal. Changes in hardness, oxide particle size and crystal structure were studied to determine the time-temperature stability of these alloys. An interpretation of the mechanism of oxide agglomeration is proposed. One of the most striking features of dispersion strengthened metal-metal oxide alloys is their stability at elevated temperatures, both with respect to recrystallization and maintenance of mechanical properties after exposure at high temperatures. A small amount of work has been done on the re-crystallization phenomenon in dispersion hardened metal-metal oxide alloys'l and several theoretical treatments have been advanced regarding the stability of these alloys by Lenel and Ansell,8 and by Grant and his co-workers.9, 10 This paper reports on metallographic and X-ray studies following various heat treatments of Cu-AI2D3 and Cu-SiO2 alloys at elevated temperatures and the effect of subsequent cold work on the recrystallizalion temperature. An interpretation of the recrystallization behavior of this type of alloy, based on the decomposition and agglomeration of oxides, is proposed. EXPERIMENTAL PROCEDURE Cast ingot bars of copper-1.59 pet Si and Cu-0.77 pet Al, 7/8 in in diam, were annealed in argon for 80 hr at 1000CC for homogenization. The homogenized rods were machined into fine chips and ball milled. Milled particles in the range minus 20 to plus 60 mesh were separated for internal oxidation. The internal oxidation was accomplished by the same method used by Preston and Grant,9 except that the oxidalion temperature for the Cu-Si alloy was 750°C, and for the Cu-A1 alloy was 800°C. These powders were then hydrogen-reduced at 450°C, compacted in a copper container, evacuated at room temperature to 0.04 µ, and sealed for extrusion. They were extruded at 1400°F (760°C) with a ram speed of 55 in. per min for an extrusion ratio of 15.6 to 1 to give a rod 0.38 in. diam by about 3 ft long.

Jan 1, 1962

By Everett H. Graff, Ray H. Misener

THE Sol de Oro mine is in the province of Nazca, 487 km. southeast of Lima, and 60 km. inland from the coast at an elevation of 1200 m. above sea level. From Lima the mine may be reached in 8 hr. by automobile; 472 km. from Lima to Nazca over the paved Pan-American Highway and 15 km. from Nazca to the mine over a good graveled road. The trip from Lima can also be made in 2 hr. via the Faucett Air Lines which make two stops weekly at Nazca. The [Compania] Aurifera Nazca, owning and operating the Sol de Oro mine, was organized in Lima in 1930 by a group of prominent Peruvian mining men, including Ing. Carlos Alvarez Calderon, Dr. Alfredo Alvarez Calderón, Ing. Hector Boza, Ing. Jorge Félix Remy, Ing. Eulogio Femandini, Sr. Fernando Wiese, and Sr. Julio East. The nine claims in the Sol de Oro group owned by the company comprise an area of 52 square kilometers. Development of the property was not started until 1932 and only then under adverse conditions, owing to lack of transportation facilities. Mining machinery and other supplies could be taken as far as Ica by boat and railroad, but to transport them over the 180 km. of hot, sandy desert from Ica to the mine was a problem. There was no road in those days and only a few of the most venturesome truck drivers cared to contract the hauling. Another problem the company had to face was that of securing adequate labor. The Sol de Oro is in an agricultural region, and was forced to look to the near-by cotton plantations for men. Experienced men were imported from the "sierras," but they did not stay. The men are accustomed to high altitudes and cold climate and cannot easily acclimate themselves to the hot and arid coastal region. As a consequence the company has been forced to hire the inexperienced local laborers and train them for mining. The company has established three separate camps at the Sol de Oro property. Each is approximately one kilometer from the other and connected by auto road. The upper mine camp consists of living quarters for 300 workmen and their families, a general mine office, carpenter shop and timber-framing shed, compressor house, drill-sharpening and drill-repair shop, first-aid station, time office, school and store. At the central or "empleados" camp there is a 200-ton cyanide plant, general offices, warehouse, powerhouse, shops, laboratory, hospital, school, guest house, an 18-room hotel for the single staffmen, and 12 completely modern five-room cottages for the married staff employees. At the lower camp are living quarters for 200 workmen and their families, two general stores, a school and a small theater. Below this camp, along the river, are the company wells and pumping plant supplying water for mine, mill, and camp uses.

Jan 1, 1945

OF the many categories into which scientific knowledge has been arbitrarily 'divided, the one that has proved most. applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. The many excellent textbooks of physical chemistry provide ample material on the principles of this subject for the student of steelmaking processes. It is the purpose of this chapter to provide a concise review of the principles of physical chemistry that have proved useful in studies of steelmaking and at the same time to present some of the data that are essential to the application of physical chemistry to reactions at high temperatures. Certain parts of physical chemistry require rather formidable mathematics for their complete development, but in the main those applications in which we are here interested can be expressed in fairly simple terms. Many of the equations are logarithmic, and we shall use the symbols In X and log X to represent, respectively the natural and the common logarithm of X. The two are related-by In X = 2.303 log X. Logarithms may, be read from a good slide rule with sufficient accuracy for our purposes. In a few spots a knowledge of the calculus will be helpful. MATTER Innumerable forms of matter may, be recognized, and these may be converted by chemical processes into others, as ore, coke, and air are converted into iron, slag, and gas.. Whenever such a change occurs there is a corresponding change in the amount of energy associated with the matter. The process may require an input of energy, as in the electrolytic production of aluminum, or it may result in an output of energy, as in the combustion of fuel. The basic laws of the conservation of matter and of energy tell us that we cannot change the total amount of matter or the total amour t of energy.. When the fuel pile is used up, we realize that it has simply been converted into other forms of matter; .i.e., ash

Jan 1, 1964

By Arthur Fleischer

THE Kalunite process? for the production of metal-grade alumina from alumina-containing ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of zoo tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. PRODUCTION OF ALUMINUM The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century for alunite is a mineral with an ancient history-it was used in Europe and in China as a source of potassium alum. It never had been used successfully in. this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent, that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim

Jan 1, 1944

By A. T. Beckwith

This paper concerns measurements of low-velocity air currents and investigations on mine ventilation by means of chemical smoke. The chemical smoke used is produced without flame and at ordinary mine temperatures, and therefore presents no ignition hazard in gaseous mines. Mining men who have worked in open-light mines are familiar with the use of tobacco smoke in determining the direction of air travel and approximately measuring low-velocity air currents. The use of chemical smoke is merely a refinement on the use of tobacco smoke and the flameless low-temperature source of chemical smoke has the additional advantage that it can be used in gaseous mines. Ventilation smoke apparatus, Fig I, is a simple device for producing dense white smoke. The apparatus as shown consists of a rubber aspirator bulb which is used to force air through a glass "smoke tube" containing a chemical substance that produces a dense white smoke on contact with air. The apparatus was developed by engineers of the U. S. Bureau of Mines.' It is inexpensive, weighs less than 3 oz, is easily carried in a pocket, and requires no skill to operate. Smoke apparatus is invaluable in practical mine ventilation work for: (I) measuring low-velocity air currents, (2) detecting air leakage, (3) observing airflow characteristics. This paper is written to show the merits of the apparatus, and is based upon findings through its extensive use, during the past six years, in mines operated by the Lehigh Navigation Coal Co. Inc. The Apparatus Certain chemicals, such as stannic chloride (SnCl4) and pyrosulphuric acid (H2S2O7) produce "white smoke" when exposed to air. Stannic chloride gives off vapors which on contact with moist air cause the formation of solid hydrates, of which SnCl4.5H20 is the most important. Pyrosulphuric acid decomposes when exposed to air with the evolution of sulphur trioxide (SO3) fumes, which become white upon contacting moisture in the air. A chemical, such as one of the above, is the active substance in a smoke tube. The glass tubes are hermetically sealed during manufacture, and are made ready for use by merely breaking off the tips at the conveniently located file cuts. When the smoke tube is connected to the aspirator, depressing the aspirator bulb forces air into contact with the chemical, and smoke discharges from the open end of the tube. A white solid (a hydrate if stannic chloride is used, or sulphur trioxide if pyrosulphuric acid is used) may occasionally form a cake in the outlet opening of a smoke tube. A small wire such as an ordinary paper clip can be conveniently employed to dislodge the cake should it seal the tube. When the assembled apparatus is not

Jan 1, 1949

GOD the Almighty has all things well ordered; in G particular, the effects and attributes of the seven planets whose reign and course (by the grace of God) determine for the most part not only our own life and death but also the growth and decay of vegetable and mineral life, so that the aforesaid planets generate and develop in a wondrous way the ores of gold and other metals in minerals, rocks, and earths. Specifically, the Sun develops the ores of gold, the Moon the ores of silver, Venus the ores of copper, Saturn the ores of lead, Jupiter the ores of tin and bismuth, Mars the ores of steel and iron, and so on. Since, however, no ore is made alone but each is made and wrought so that it is associated with other ores, it is necessary to know the art of separating the thus-made ores after they have become metals; as for instance, silver from lead and copper; gold from silver, and so on. [2]* If this is to be done usefully, you must be able to assay and must understand everything that is needed in connection therewith. It is obviously true and clear as light of day that some kinds of copper contain silver and some kinds of silver contain gold. In order that you may be able to separate them, so that each is obtained by itself and can be worked with profit and re ward you need first of all a true assay for the values of such metal. The assay, by revealing how great they are, whether the pure has been obtained separate from the worthless matter, and what the admixture is, advises you whether it would be worth the expense and the effort to start mining operations. Assaying also indicates how much silver there is in a centner of ore or how much copper and lead there are in

Jan 1, 1949

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By W. M. Bertholf

IN 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral can make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory," as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,1 but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1946

By J. David Lowell

For his contributions to the field of mining geology, a striking example being his brilliant inte.rpretation of the complex geologic history of the San Manuel District (Pinal County, Arizona) which resulted in the discovery of the Kalamazoo orebody, and for his lecture, "Copper Resources in 1970." On a low desert ridge six miles south of Cairo lie the remains of the world's earliest known mining town, Maadi of predynastic Egypt. Copper artifacts, including ingots and an ax head which was spoiled in casting, indicate that copper ore was smelted in Maadi, and radiocarbon dating has placed the activity at least as early as 3300 B.C. This is the oldest documented date for the use of smelted copper, the first industrial metal used by man. Copper was mined and smelted almost as early in Asia Minor and on the island of Cyprus, but the greatest development of the budding copper industry was in Egypt, where specific historical records show that about 10,000 tons of copper metal were produced in the period from 1850-1580 B.C. Contrast this production of 35 tons per year with the present world production of about 7 million tpy. Evolution of the Copper Industry The copper ore mined by the ancients was high grade, and the copper produced was expensive. The copper industry began with narrow high-grade veins, but has evolved to the point where massive earth-moving equipment can be operated in huge, low-grade open pits. Indian pits dug before 3000 B.C. in the Lake Superior district were in ore which averaged 15% Cu. His- torical research done by Arthur Brant has shown that copper cost in the Middle East in 1840 B.C. in terms of 1970 labor dollars was about $25 per lb. The copper mined in northern Europe in 1540 in the time of Georgius Agricola averaged about 8% Cu, and the cost in 1970 labor dollars was about $10 per lb. Average ore grade had dropped to about 6% Cu in 1890, and the cost of copper in the U.S. in 1970 dollars was about 45¢ per lb. Butte, Mont., was a good example of the efficiently operated vein mines of this time. In 1906, Daniel Jackling made a dramatic entrance into the copper scene with the Bingham Canyon open-pit copper mine and proved that more profit was possible mining 2% porphyry copper ore on a

Jan 1, 1971

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators 1-5 have noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilities6 and by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported' to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of this portion is shown in Table I and an approximate mineralogical analysis is shown in Table II. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of -6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1952

By G. E. McElroy

Changes in existing airway and fan-installation conditions offer the most common opportunities for effecting economical operation of mine-ventilating systems, but the largest possibilities for securing this result lie in the original design of the main airways for efficient service. Formulas, and charts for their graphical solution, are presented herewith for the determination of the elements of airways design when the conditions of service are known or may be roughly approximated. Although the analyses are made with particular reference to metal-mine airways, there is no essential difference between main airways in metal and coal mines, and the methods presented are applicable to both. Little attention is paid to designing airways for maximum economy in the ventilation of metal mines. Most of the openings used as main airways are originally designed and used for transportation and other operating purposes. Even where openings are made primarily for ventilation, the possibility of their future use for other operating purposes, or even custom alone, usually results in the selection of a size and shape similar to those of existing openings. Natural conditions, such as heavy ground, often seriously limit the size of opening that can be maintained without excessive expense; and various operating factors, such as velocity limitations on traveling roads, often dictate size requirements in excess of those required for economy in ventilation only. In metal mines the main airways are, as a rule, too small rather than too large for economic service, with the general result that the quantities in circulation are often less than the mine's proper requirements over long periods, even though excessive amounts of power are applied in an effort to remedy conditions. Increasing the area of an airway increases the cost for excavation and lining practically proportionately but at the same time affects a very rapid decrease in power requirements. The balancing of these two factors of the expense to give a minimum total yearly operating cost for ventilation is mainly a matter of proper original design of the main airways of the mine, since the large volumes handled through these parts of the system involve large power costs and thus present opportunities for effecting large savings through proper design. Many of the factors

Jan 1, 1932

By Frank G. Miller

The lower cost of producing oil from naturally flowing wells compared with pro-luction costs accruing from artificial lifting methods has stimulated much research, rith the joint purpose of extending the natural flowing life of wells and of increas-ng the productivity of small wells. The iboratory investigation described herein was made to determine the effect of a lotted liner on the pressure gradient in the icinity of the wall of a flowing well. Flow estrictions caused by the liner induce nergy losses between the oil-bearing for-lation and the inside of the liner, which lay be reduced by improved liner design, nd thereby the flow capacity of wells may e increased. These losses have been evalu-ted for rectangular slots of different sizes, nd means are suggested for reducing them. The dearth of information concerning the ature of the flow of fluids from uncon-slidated sands through small openings in he walls of. pipes—as represented by the ow of oil from an oil sand into a slotted ner—is acknowledged. Although the bene-ts to be realized by operators through the se of optimum liners is just beginning to e recognized generally, Coberlyl in 1937 ointed out that the functioning of screen is is an important factor in the pro-uction of oil. From his study on the :lection of size of oil strings for wells in California, Parks2 concluded, in part, that the perforated section of the oil string deserves continued study, especially with respect to the selection of perforations. The growing use of gravel packing resulting from certain research findings lends even more significance to the problem of selecting optimum liners, as the application of these methods usually requires slotted liners or other kinds of perforated liners. The present study was made to obtain further information for the guidance of engineers and operators in selecting slotted liners and to develop a laboratory method that may be used in analyzing possible pressure conditions surrounding most types of perforated casings used in producing oil wells, so that the present inadequate fund of knowledge on this important subject may be expanded. Discussion of ProbleM At the beginning of the investigation the following assumptions were made regarding bottom-hole conditions of a producing oil well and the oil-sand reservoir it penetrates: (I) Conditions of steady-state flow exist, (') a a homogeneous liquid is being produced) (3) no contaminating material (such as drilling fluid) is present between the liner and the face of the oil-bearing sand, (4) the well is vertical and completely penetrates a horizontal sand stratum of uniform thickness occurring between two impermeable strata, and (5) the flow is wholly viscous. If the foregoing assumptions are made, with the added requirements that the sand

Jan 1, 1941

By Frank G. Miller

The lower cost of producing oil from naturally flowing wells compared with pro-luction costs accruing from artificial lifting methods has stimulated much research, rith the joint purpose of extending the natural flowing life of wells and of increas-ng the productivity of small wells. The iboratory investigation described herein was made to determine the effect of a lotted liner on the pressure gradient in the icinity of the wall of a flowing well. Flow estrictions caused by the liner induce nergy losses between the oil-bearing for-lation and the inside of the liner, which lay be reduced by improved liner design, nd thereby the flow capacity of wells may e increased. These losses have been evalu-ted for rectangular slots of different sizes, nd means are suggested for reducing them. The dearth of information concerning the ature of the flow of fluids from uncon-slidated sands through small openings in he walls of. pipes—as represented by the ow of oil from an oil sand into a slotted ner—is acknowledged. Although the bene-ts to be realized by operators through the se of optimum liners is just beginning to e recognized generally, Coberlyl in 1937 ointed out that the functioning of screen is is an important factor in the pro-uction of oil. From his study on the :lection of size of oil strings for wells in California, Parks2 concluded, in part, that the perforated section of the oil string deserves continued study, especially with respect to the selection of perforations. The growing use of gravel packing resulting from certain research findings lends even more significance to the problem of selecting optimum liners, as the application of these methods usually requires slotted liners or other kinds of perforated liners. The present study was made to obtain further information for the guidance of engineers and operators in selecting slotted liners and to develop a laboratory method that may be used in analyzing possible pressure conditions surrounding most types of perforated casings used in producing oil wells, so that the present inadequate fund of knowledge on this important subject may be expanded. Discussion of ProbleM At the beginning of the investigation the following assumptions were made regarding bottom-hole conditions of a producing oil well and the oil-sand reservoir it penetrates: (I) Conditions of steady-state flow exist, (') a a homogeneous liquid is being produced) (3) no contaminating material (such as drilling fluid) is present between the liner and the face of the oil-bearing sand, (4) the well is vertical and completely penetrates a horizontal sand stratum of uniform thickness occurring between two impermeable strata, and (5) the flow is wholly viscous. If the foregoing assumptions are made, with the added requirements that the sand

Jan 1, 1941

By Morris Muskat

A general theory has been developed for the effect of permeability stratification on the efficiency of the gas-injection phase of cycling operations. It has been applied to three special types of permeability variation; namely, exponential, probability, and linear. In the case of the exponential permeability distribution the effect of areal pattern sweep efficiency was also taken into account. The exponential permeability distribution can be characterized by the ratio of the maximum to minimum permeability, which has been termed the stratification constant. Curves were calculated for the variation in total wet gas recovery and total gas throughflow, to give that recovery to various abandonment limits of the wet gas content in the produced gas, as a function of the stratification constant. The cumulative wet gas recovery decreases monotonically as the stratification constant increases and is generally higher at the lower values of the wet gas content abandonment limits. The total gas throughflow first rises to a maximum as the stratification increases, and then ultimately declines. The effect of the areal sweep pattern efficiency is relatively minor as compared to that of the stratification constant, except in the region of low values of the latter where the formation is substantially uniform. The probability distribution can be characterized by a "variation" parameter varying from o to I as the formation changes from strict uniformity to extreme variability. The curves of total wet gas recovery and total gas throughflow to different abandonment limits of wet gas content versus the variation parameter have the same general characteristics as for the exponential permeability distribution. In the linear permeability distribution the ratio of maximum to minimum permeability also serves as a stratification constant index defining the distribution. The curves of total wet gas recovery and gas throughflow to fixed abandonment limits versus the stratification constant are similar to those for the exponential permeability distribution. However, for the higher values of the stratification constant the recoveries and throughflows do not asymptotically fall to o as in the latter, but approach constant values determined by the abandonment limit of wet gas content in the produced gas. Introduction It is becoming generally recognized that one of the most important factors determining the economic feasibility of cycling operations is the areal continuity and permeability distribution of the producing formation. While the effects of areal variations in permeability, porosity, thickness, and well pattern on the sweep efficiency can be evaluated by electrical model studies,' those due to permeability stratification require separate treatment. Several studies have been reported2,3 on the' influence of permeability variations on the wet gas recovery by cycling. In these, however, discontinuous permeability variations either have been assumed explicitly, or the analysis has been carried through as if they were discontinuous. While, in fact, the actual permeability profiles will undoubtedly be discontinuous, recent develop-

Jan 1, 1949

By V. J. Berry, J. D. Pendergrass

Well pressure transient tests provide a means for directly obtaining information about formation pressure and reservoir flow capacity. Such tests have also been proposed for determining presence and location of faults or other reservoir closures and for measuring oil in place. For mathematical convenience, most theoretical studies have considered the reservoirs to be homogeneous. Definitive information is not yet available to show whether the actual presence of nonuniformities will make pressure transient behavior different from that of a uniform reservoir. The conclusions reached from actual transient tests are questionable, therefore, insofar as they rely on the original assumption of homogeneity. One type of nonuniformity commonly assumed to exist is that of stratification. In most reservoirs the strata are thought to be in vertical communication. Equations for the transient flow of a single-phase, compressible fluid in a one-well, bounded, circular reservoir have been solved for several situations involving crossflow between multiple strata of various thicknesses and permeabilities. The results show that except for the very early flow period, which usually is too short to be analyzed, the transient performance observed at the well is substantially identical with that of a homogeneous reservoir having the same dimensions and having the same steady-state flow capacity. Thus, stratification does not adversely affect interpretation of well transient tests. This conclusion holds for all commonly encountered combinations of reservoir thickness and external radius. Deviations are observed for unusually thick reservoirs whose outer radii are relatively small. The results of these studies also show that the presence and the amount of stratification cannot be simply diagnosed from reservoir pressure transient data when there is crossflow between strata. INTRODUCTION The last decade has brought wide acceptance of the transient well pressure test for determining reservoir parameters. Following the original work of Hurst and van Everdingen,1 the mathematical theory was thoroughly explored. Numerous authors have suggested how to determine static reservoir pressure, permeability-thickness product, original oil in place and reservoir limits for different reservoir geometry. The same mathematical techniques have been used to predict the transient performance of a reservoir over a long period of time. Most of the theoretical work has been for homogeneous, isotropic systems. Some results have also been presented for a homogeneous, anisotropic reservoir.2 Petroleum reservoirs are not homogeneous. The deposition process seems to favor creation of a stratified formation. This concept is sufficiently well accepted so that the most natural extension of the transient flow theory beyond the homogeneous case is to a stratified formation. Results for a stratified reservoir with no vertical communication between layers can be obtained from the results for a homogeneous reservoir. Lefkovitz, et a1,3 have given a thorough treatment of the two-layer case. Two recent papers4,5 have treated the case of a two-layered reservoir with vertical communication or crossflow, between layers. Russell and Prats4 find that, after a relatively short time, the two-layered reservoir with crossflow exhibits a simple exponential pressure decline. From this time forward, the behavior is not distinguishable from the behavior of a homogeneous reservoir having the same steady-state flow capacity. The results of Katz and Tek 5 are equivalent. Russell and Prats4 also speculate that a multi-layered reservoir with crossflow will behave as a homogeneous system after long enough production time "... providing the contrast in kh between layers is not too great". They also suggest that, at intermediate times, "... the relative positions of the layers with respect to each other will have a great influence on the production behavior and on the time at which the previously mentioned large-time approximation might be valid". Katz and Tek5 remark upon the mathematical difficulty of treating a reservoir having many layers or strata. If relative position of the layers is also

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. 'H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. 'E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 'C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

By H. A. Wilhelm, P. Chiotti, G. A. Tracy

A summary of analytical, X-ray, thermal, and metallographic data obtained in the study of the Mg-U system is presented. No intermetallic compounds are formed by these two elements, and their mutual solubility is limited at temperatures up to 1255°C. The compositions of the liquids which coexist at 1135°C under a pressure of 3 atm are 0.14*0.05 wt pet U in magnesium, and 0.004 wt pet Mg in uranium. The solubility of uranium in magnesium decreases to 0.0510.03 wt pet at 675OC, and to about 0.0005 wt pet at 650°C. Due to the reactivity of both uranium and magnesium toward crucible materials, the choice of a suitable crucible presented a problem. Crucibles made from high purity magnesia to which 10 wt pet MgF2 was added to reduce porosity proved to be satisfactory. Some observations made with the use of other crucibles are given. THIS investigation was made to establish the phase diagram for the Mg-U system. Ahmann,' formerly of the Ames Laboratory, did some work on the system. He used several methods in an attempt to prepare Mg-U alloys. One of the methods involved the reduction of UF, with a large excess of magnesium. In these experiments, the magnesium wet the surface of the uranium, but there was no evidence for compound formation. The maximum solubility of magnesium in uranium was indicated to be 0.01 wt pet. In another set of experiments, uranium chips as well as uranium powder were heated in contact with molten magnesium in a graphite crucible for periods of time up to 48 hr. A reaction layer was found at the Mg-U interface in several instances. X-ray analysis of the layer material showed the presence of UC and some additional unidentified lines which were interpreted as indicating the possibility of an intermetallic compound of uranium and magnesium. These studies indicated the maximum content of magnesium in uranium to be 0.043 wt pet. One sample of magnesium which had been heated at 1025°C in contact with excess uranium was found by chemical analysis to contain 0.275 wt pet U. Rules, based on empirical or semi theoretical considerations, which attempt to predict the alloying behavior of metals have been presented in the literature. Although these rules are not infallible, they nevertheless serve as useful guides. Using them, several generalizations can be made concerning the Mg-U system. According to Hume-Rothery's' atomic

Jan 1, 1957

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76'7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967