Search Documents

By L. H. Cadoff, L. M. Adelsberg

The layer growth method has been used to investigate the reaction kinetics of liquid titanium and hafnium with carbon and the [liq] - [liq + TiC] and [liq] - [liq + HfC] phase boundaries at temperatures above 1800°C. The equipment and experimental procedures used in this investigation are basically identical to those described in an earlier paper' on the Zr-C reaction. Temperature control, however, was improved significantly by connecting a Latronics Colo-Ratio automatic pyrometer and a controller to the power source. The subsequent temperature variations were ±10°C; previously ±20°C was obtained using manual controls. The absolute accuracy of the pyrometer, however, must be considered to be only ±40°C.* The spectrographic analyses of the materials used in this study are listed in Table I. The isothermal reactions of titanium (1800° to 2700°C) and hafnium (2300" to 3000°C) with carbon (graphite crucibles) resulted in the formation of carbon-saturated liquid metal and layers of Tic and HfC, respectively. The thicknesses of the carbide layers, determined from metallographic measurements at 100 times, as a function of carburization time and temperature are given in Figs. 1 and 2. At each temperature, parabolic growth behavior for these reactions was observed and could be expressed as x2 =Kpt, where X is scale thickness (corrected for heating and coolingL), Kp the parabolic growth constant, and t the isothermal carburization time. Values of Kp as a function of temperature for the carbides are shown in Fig. 3 and listed in Table 11. The growth constants are expressible as: kpTiC = 0.2 exp(-61,800/RT) sq cm per sec for Tic and Kp HfC = 2.62 exp(-95,300/RT) sq cm per sec for HfC. The liquidus phase boundaries were determined from metal samples treated in graphite crucibles for different times ranging from 4 to 100 min at each of the temperatures indicated in Table 11. Metallographic examination revealed that the carbide precipitates were distributed uniformly throughout the frozen metal matrices. This is attributed to the rapid cooling rates (800°C per min) and the small difference in density between the precipitated carbide and the liquid metal.

Jan 1, 1968

By A. D. K. Laird, John A. Putnam

This paper describes the application of x-ray theory to design procedures in connection with fluid saturation determinations during fluid flow experiments with porous media. A reliable and rapid method for calibrating the x-ray apparatuy is described. Extension of the method to fluid saturation determinations in three-fluid systems is described. INTRODUCTION In rerearch on oil production problems a method is required which will give quickly the quantity of each component of a fluid flow system present at any cross-section of a porous medium. The sample of porous medium under investigation is usually referred to as a core. The ratio of the volume of one component to the total fluid volume is defined as the saturation of the porous medium by that component. This ratio is generally given as per cent saturation. Some means of measuring saturation which have received consideration include: electrical conductivity of the fluids;1,2 emissions from radioactive tracers dissolved in the fluids; the radioactivity of silver caused by reflection of neutrons from hydrogen atoms in the fluids;' the attenuation of a microwave beam. the diminution and phase shift of ultrasonic wave trains.4,5 and the reduction in intensity of x-ray beams in passing through the fluids. X-rays have already been used with some success. Since every material has a different power to absorb x-rays, the reduction in intensity of an x-ray beam as it passes through a core depends on the fluids present. The strength of the emergent beam can be found by converting its energy into a measurable form such as heat or ionic current. or by its effect on a photographic plate or fluorescent screen. The beam strengths could be interpreted as quantities of known fluids in the core if, previously, these beam strengths had been identified with a known combination of the same fluids. With some fluid cornbinations it might be desirable to dissolve powerful x-ray absorbing materials in one or more of the fluids, to increase the differences in the beam strengths for various fluid saturations. Boyer, Morgan and Muskat6 have described a method of measuring two component fluid saturation. One component was air or water; the other. minerat seal oil in which was dissolved 25 per cent by weight of iodobenzene to increase its absorbing power. The x-ray source was a tungsten target tube operated at 43 kv potential. The beam emerging from the core was measured as ionic current flowing across an air-filled ionization chamber by means of an amplifying circuit and galvanometer. Another portion of the beam from the x-ray tube was passed through a metal plate and measured in another ionization chamber. This portion, called the monitor beam, was used as an indication of the performance of the x-ray tube. The galvanometer readings were calibrated against air-oil core saturations, gravimetrically determined. The method was apparently established by experimental means. In the present investigation the available theory of x-radia-tion was surveyed with a view to extending the usefulness of the method and to developing design procedures for its application to measurement of fluid saturation in porous media. Application of the theory permits prediction of relative meter readings to be expected for any combination of porous matrix, various saturating fluids and auxiliary filtering media. It is thus possible to calibrate the equipment in terms of fluid saturation by an indirect but rapid technique. The results of calculations based on x-ray theory indicate. and results of the saturation calibration technique confirm. that a valid measurement of the saturation of the core can be made for any two components and in some cases for three components. THEORY The strength of an x-ray beam, after it has passed through a distance. 1, of matter of density, p, and mass absorption coefficient, µ at a given wavelength, A, may be expressed by the absorption formula I = I0 e ...........(1) where I, represents the intensity of the incident x-ray beam and I is the intensity of the emergent beam. The expression e is called the transmission factor of the material. The variation of I,, with wavelength depends upon the materials through which the x-ray beam has previously passed and upon the spectral distribution of energy at the source of the x-radiation. A group of curves. called spectra. which show the variation of intensity with wavelength and x-ray tube voltage are given in Fig. 1. These curves represent the general radiation from a tungsten target tube. When the tube voltage is greater than 69.3 kv, the characteristic radiation of the tungsten is emitted and is superposed on the general radiation. At a given voltage the minimum wavelength A,,,,, at which energy can be emitted by an x-ray tube is given by the formula 12,340 xml. = ——..........(2) volts where A,.,,.. is in Angstrom units. The wavelength at which the spectra have maximum intensity a1so decreases with increasing x-ray tube voltaue. The area under each curve represents to an arbitrarv scale the total energy emerging from the x-ray tube for that voltage. The variation of µ with wavelength has been determined for many substances and may be found in such references as those by Compton and Allison7 and by Hodgman.8 The phenomenon of absorption is composed chiefly of the capture of photons by the atoms of the absorbing material with associated displacement of electrons, and of the scattering, or the deflection, of the photons by the atoms. Curves of these mass absorption coefficients show jump discontinuities. or absorption edges. at wavelengths which are short enough for the photons,

Jan 1, 1951

By John A. Putnam, A. D. K. Laird

This paper describes the application of x-ray theory to design procedures in connection with fluid saturation determinations during fluid flow experiments with porous media. A reliable and rapid method for calibrating the x-ray apparatuy is described. Extension of the method to fluid saturation determinations in three-fluid systems is described. INTRODUCTION In rerearch on oil production problems a method is required which will give quickly the quantity of each component of a fluid flow system present at any cross-section of a porous medium. The sample of porous medium under investigation is usually referred to as a core. The ratio of the volume of one component to the total fluid volume is defined as the saturation of the porous medium by that component. This ratio is generally given as per cent saturation. Some means of measuring saturation which have received consideration include: electrical conductivity of the fluids;1,2 emissions from radioactive tracers dissolved in the fluids; the radioactivity of silver caused by reflection of neutrons from hydrogen atoms in the fluids;' the attenuation of a microwave beam. the diminution and phase shift of ultrasonic wave trains.4,5 and the reduction in intensity of x-ray beams in passing through the fluids. X-rays have already been used with some success. Since every material has a different power to absorb x-rays, the reduction in intensity of an x-ray beam as it passes through a core depends on the fluids present. The strength of the emergent beam can be found by converting its energy into a measurable form such as heat or ionic current. or by its effect on a photographic plate or fluorescent screen. The beam strengths could be interpreted as quantities of known fluids in the core if, previously, these beam strengths had been identified with a known combination of the same fluids. With some fluid cornbinations it might be desirable to dissolve powerful x-ray absorbing materials in one or more of the fluids, to increase the differences in the beam strengths for various fluid saturations. Boyer, Morgan and Muskat6 have described a method of measuring two component fluid saturation. One component was air or water; the other. minerat seal oil in which was dissolved 25 per cent by weight of iodobenzene to increase its absorbing power. The x-ray source was a tungsten target tube operated at 43 kv potential. The beam emerging from the core was measured as ionic current flowing across an air-filled ionization chamber by means of an amplifying circuit and galvanometer. Another portion of the beam from the x-ray tube was passed through a metal plate and measured in another ionization chamber. This portion, called the monitor beam, was used as an indication of the performance of the x-ray tube. The galvanometer readings were calibrated against air-oil core saturations, gravimetrically determined. The method was apparently established by experimental means. In the present investigation the available theory of x-radia-tion was surveyed with a view to extending the usefulness of the method and to developing design procedures for its application to measurement of fluid saturation in porous media. Application of the theory permits prediction of relative meter readings to be expected for any combination of porous matrix, various saturating fluids and auxiliary filtering media. It is thus possible to calibrate the equipment in terms of fluid saturation by an indirect but rapid technique. The results of calculations based on x-ray theory indicate. and results of the saturation calibration technique confirm. that a valid measurement of the saturation of the core can be made for any two components and in some cases for three components. THEORY The strength of an x-ray beam, after it has passed through a distance. 1, of matter of density, p, and mass absorption coefficient, µ at a given wavelength, A, may be expressed by the absorption formula I = I0 e ...........(1) where I, represents the intensity of the incident x-ray beam and I is the intensity of the emergent beam. The expression e is called the transmission factor of the material. The variation of I,, with wavelength depends upon the materials through which the x-ray beam has previously passed and upon the spectral distribution of energy at the source of the x-radiation. A group of curves. called spectra. which show the variation of intensity with wavelength and x-ray tube voltage are given in Fig. 1. These curves represent the general radiation from a tungsten target tube. When the tube voltage is greater than 69.3 kv, the characteristic radiation of the tungsten is emitted and is superposed on the general radiation. At a given voltage the minimum wavelength A,,,,, at which energy can be emitted by an x-ray tube is given by the formula 12,340 xml. = ——..........(2) volts where A,.,,.. is in Angstrom units. The wavelength at which the spectra have maximum intensity a1so decreases with increasing x-ray tube voltaue. The area under each curve represents to an arbitrarv scale the total energy emerging from the x-ray tube for that voltage. The variation of µ with wavelength has been determined for many substances and may be found in such references as those by Compton and Allison7 and by Hodgman.8 The phenomenon of absorption is composed chiefly of the capture of photons by the atoms of the absorbing material with associated displacement of electrons, and of the scattering, or the deflection, of the photons by the atoms. Curves of these mass absorption coefficients show jump discontinuities. or absorption edges. at wavelengths which are short enough for the photons,

Jan 1, 1951

By E. C. Tveter, R. B. Tippin

The separation of minerals by heavy liquids is a standard laboratory technique which goes back at least 50 years, but commercially economic application of this principal to ore concenfration has been prevented by problems of liquid recovery. Recent investigations which demonstrate the different types of liquid-solid systems on various ores using the two major heavy liquids - methylene bromide and tetra-bromoelhane — are discussed in this article. As a result of these studies, over-all liquid recovery, and especially desorption of heavy liquid from the mineral surface, was improved by the use of surfactants as well as both thermal and mechanical energy. The examples given in the article indicate that heavy liquids which should find major commercial use in ore concentration are now available. The sink-float process using a heavy liquid medium has long been recognized as a nearly perfect method of mineral separation based on the differences in density of the minerals. The use of heavy liquid separation (HLS) offers the potential of an ore dressing method that provides the maximum possible natural concentrate grade and high recovery. In addi- tion the process requires no water, causes no waste disposal problems, and is extremely simple — the crushed ore is merely introduced into a liquid whose density is between that of the minerals to be separated. The minerals lighter than the liquid float while those heavier than the liquid sink. As such, HLS has become a standard laboratory tool but major commercial application has been prevented by the requirement for complete recovery of the heavy liquid, imposed by economics and materials handling hazards. Investigations, both in the United States and abroad, have shown that improved liquid stability as well as improved chemical engineering techniques brighten the future for HLS in ore dressing. The available commercial heavy liquids suitable for mineral separation cost from $2.00 to $20.00 per gallon1 and on this basis alone their complete recovery is economically desirable. Possibly of even greater importance is the fact that any residual heavy liquid remaining on the products could create a serious toxicity hazard. Consequently, to make the process commercially attractive requires (1) essentially complete removal of the liquid from the ore products and (2) optimum recovery of the liquid for reuse. Until recently these two stipulations have remained as obstacles but laboratory and pilot plant research now in progress suggests that these may soon be overcome. Various heavy liquid recovery systems have been proposed to meet these requirements and might be classified into one or more of the following three general classes: Solvent Wash (Fig. 1): The dissolution of the heavy liquid from the ore with a less expensive solvent,

Jan 1, 1969

By Ralph D. Parker

The Frood mine (Fig. 1) is 2½ miles north of Sudbury, at a general elevation of 1000 ft. above sea level. It includes the original Frood location, which was the No. 3 mine of the Canadian Copper Co., and the adjoining Frood Extension, which until 1929 belonged to the Mond Nickel Co. Mine Openings The mine is operated from two vertical shafts and one underground incline shaft. No. 3, for men, supplies and ore, is a vertical six-compartment shaft in the footwall of the south mining area and extends froin surface to a depth of 3045 ft. No. 4 is a vertical three-compartment shaft, 2500 ft. north of No. 3 and adjacent to the north mining area. It extends from surface to a depth of 3345 ft., and is used exclusively for hoisting ore. No. 5 shaft, inclined at 65' to the horizontal and of three compartments, is near No. 4 and extends from the 2600-ft. level to 77 ft. below the 3100 level. It is used for development below the 2800 level. The ventilation shaft, No. 1, with which this paper is directly concerned, will be described fully in the following pages. Mining Methods The orcbody is laid out in 80-ft. sections at right angles to the gcneral strike and numerically indicated from the southern extremity toward the north. Each section consists of a 45-ft. stope and a 35-ft. pillar, extending the full width of the orebody. Pillars and stopes are superimposed from level to level. The present mining territory is divided into two vertical areas, a north and a south area. Both areas have the same number of stopes on each level, the two areas being separated by 10 sections to be mined later. In a few instances, at the ends of the south area, where the orebody has narrowed, longitudinal stopes are used, of more than the usual 45-ft. width. It will thus be seen that mining operations hare been concentrated in two relatively small areas, offering

Jan 1, 1934

By J. E. Johnson

Charcoal-iron is quantitively so unimportant compared with coke-iron, that its qualitative importance for many industrial purposes is entirely unkriown to many coke-furnace-men, and to the great majority of the inembers of this Institute. To explain this qualitative importance, and explain some of the fact,ors that affect the quality, are the objects of this paper. A brief review of' the commercial conditions governing the charcoal-iron industry is a necessary preliminary to any adequate treatment of the subject. The advent of coke-iron, which transformed the whole iron industry commercially, left intact a limited production of charcoal-iron in the East and South, which has been conducted almays on the basis of high cost and high quality, with correspondingly high selling-price. In the Northwest, particularly in the Lake Superior district, the development has been along totally different lines, for which the close proximity of the great iron-ore deposits and the great forests of that region mere responsible. When the great white-pine forests were removed there were left behind large areas of hardwood and hemlock, to which little attention was paid in the prosperous years of the white-pine industry. But when the latter declined, the demand for lumber, and the presence of lumber-men, probably more skilled than any others in the world, caused the gradual introduction of these woods into commercial use. It was a matter of ancient knowledge that hardwood made an excellent charcoal, and to utilize the cordwood left after the saw-logs were removed, by converting it into charcoal and using it to smelt ore from the adjacent mines, mas an obvious step. In some cases the establishment of the furnace occurred in-

Jan 1, 1913

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not withstand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950" to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as —75" F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these requirements, but as a result of the extensive research carried on by steel manufacturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But, when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service. A great deal of credit is due to the members of the Boiler Code Committee and also to the members of the Joint A.P.I.-A.S.M.E. Committee, who have formulated codes that insure the safety of the

Jan 1, 1935

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not withstand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950" to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as —75" F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these requirements, but as a result of the extensive research carried on by steel manufacturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But, when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service. A great deal of credit is due to the members of the Boiler Code Committee and also to the members of the Joint A.P.I.-A.S.M.E. Committee, who have formulated codes that insure the safety of the

Jan 1, 1935

By George A. Colligan, John M. Lo

Electrical resistivity as a function of temperature was investigated in undercooled gallium and under-cooled Ga-In alloy of eutectic compositian to examine structural changes in undercooled melts. A continuous linear extension of the resistivity was determined for 99.999 pct pure gallium when undercooled below the stable Ga(l)-liquid, and the metastable Gafl)-liquid equilibria. In icndercooled Ga-In, a significant continuous negative departure from linear resistivity behavior was observed below the eutectic temperature. All resistivity measurements were made by the four-point probe technique. ThE temperature range for investigations into the physical properties of liquids before freezing has been greatly extended with the undercooling of massive melts of pure metals and alloys. Experimental determinations of thermal and transport properties and diffraction patterns in undercooled systems should throw further light on the structural behavior of liquids. Many measurements showing prefreezing anomalies in viscosity1'5 have been regarded677 as evidence for structural groupings in the liquid state. However, the majority of viscosity results,~)~-~~ conforming to the law 17 =A exp(~/RT), do not support theories of atomic aggregation. For the system Cd-Sb, which exhibits a metastable solid phase, Fisher and Phillipsg reported that, in undercooled alloys, the activation energies for viscous flow below the stable liquidus are much higher than those above it. Similarly, Miller et a1." observed a doubling of the activation energies for electrical conductivity in undercooled Cd-ib alloys. These effects were suggested as indicative of atomic association and clustering in the liquids at lower temperatures. With the recent establishment of metastable phases in pure gallium22 and its alloys,23 attempts were made during this investigation to undercool bulk samples and to determine the temperature dependence of electrical resistivitv. Pure gallium, when undercooled below -17°C at atmospheric pressure, can crystallize to either a stable Ga(1) phase (mp, 29.78"C) or a metastable phase identi-

Jan 1, 1967

By B. F. Oliver, C. W. Haworth

Pure tin and Sn-0.5pct Pb ingots have been frozen unidirectionally from the base. For quiescent melts that were initially undercooled, a transition from lower eqlciaxed structure to an upper columnar structure is found in the alloy ingots. Columnar to equi-axed back to columnar transitions are observed in superheated alloy ingots, but no such equiaxed band is observed impure tin. The reproducible equiaxed band is associated with a thermal undercooling followed by a recalescence. This undercooling is <5"C, whereas the critical (maximum obtainable) under-cooling for both the pure tin and the alloys used is -20°C. A similar undercooling is observed at the same position in the pure tin ingots, although in this case no clear transition in structure can be seen. The structure of the pure tin ingots is either entirely columnar or mixed columnar-equiaxed. A consideration of the detailed thermal history of the ingots indicates that the ingot macrostructures are determined by the occurrence of a local therlnal undercooling in conjunction with nuclei multiplication and transport mechanisrris. GENERALLY it is found that a pure metal ingot solidifies so as to produce an entirely columnar structure. Frequently an alloy ingot is found to have a columnar outer zone and an equiaxed central portion. Early systematic work to examine the factors controlling the formation of the equiaxed structure was reported by Northcott&apos; who showed that, for copper alloys frozen unidirectionally with a given ingot practice, the alloying element influenced the length of columnar crystals and the extent of the equiaxed structure. Northcott showed that alloys with a wider freezing range more readily produced the equiaxed structure. The nucleation process can be important in producing equiaxed structures; frequently an alloy which readily solidifies with an entirely columnar structure will produce an entirely equiaxed structure when a nucleating agent is added to the melt.&apos; The formation of the equiaxed structure was attributed by Winegard and chalmers3 to the presence of constitutional supercooling; that is, a region of liquid in front of the growing solid could have a temperature below its equilibrium liquidus temperature. Thus, with a small enough temperature gradient in the liquid, it was suggested that the presence of constitutional supercooling may be sufficient to bring about the nuclea-tion necessary for the formation of an equiaxed structure. Although this explanation is plausible, and may be relevant in many ingots, Walker has described an experiment&apos; for which constitutional supercooling seems to be an unlikely cause of nucleation. A Ni-20 pct Cu alloy, repeatedly undercooled more than 50"C, was crystallized and found to show the typical colum-nar-equiaxed structure. The separation between the liquidus and the solidus for the alloy is 40°C. Thus, in this experiment the nucleation required for the formation of the equiaxed structure must have come about in some other way than by the nucleation catalysis constitutional supercooling hypothesis. Chalmers has suggested more recently5 that nuclei (in a typical ingot) are present immediately after pouring and are prevented from redissolving by the constitutional supercooling effect. More recently Uhlman, Seward, Jackson, and ~unt&apos; have shown direct evidence using ice and organic materials that freeze dendritically that the "remelt mechanism" may be an extremely effective crystal multiplication process during the freezing of ingots under conditions involving dendritic growth. JSlia" experimentally demonstrated the detachment of dendrite arms. chernov14 has analyzed the dendrite arm detachment process as a coarsening phenomena driven by the minimization of interphase area. Katta-mis and ~lemings" working with undercooled steel melts give evidence supporting this mechanism. Mechanisms of dendrite arm detachment such as those assisted by convection are believed to be the origin of the macrostructures obtained in this study. This study makes no attempt to distinguish the relative contributions of these mechanisms. The object of the present work was to obtain accurate temperature measurements during the solidification of an ingot and to correlate these measurements with the formation of equiaxed grains in the resulting ingot structures. Similar previous work is very limited. The measurements carried out by Northcott are neither sufficiently extensive nor sufficiently accurate for any interpretation. Plaskett and winegard7 carried out experiments on A1-Mg alloys in which they observed values of the temperature gradient, G, in the liquid and rate of freezing, R (for a given alloy solute content Co), at the transition from a columnar to an equiaxed structure. They reported that equiaxed crystals were produced at values of G/G approximately proportional to the solidus composition. Similar experiments using Pb-Sn alloys carried out by £111011" showed a linear relation between G/R and the solidus composition. However, the thermocouples were in the mold wall rather than in the melt and, in one case, ingot surfaces were examined. There is ambiguity in the meaning of the values of G and R measured in all these experiments. APPARATUS AND EXPERIMENTAL PROCEDURE Alloys were prepared by induction melting 99.999 pct Sn and 99.999 pct Pb to form a Sn-0.5 wt pct Pb alloy in air in a graphite crucible and casting into a cylindrical graphite mold 6 in. long, 1 in. in diarn , and with a & in. wall thickness. This mold was mounted on a copper base through which cooling water could be

Jan 1, 1968

By T. Fraser, F. F. Giese, R. L. Sutherland

Under a cooperative agreement between United States Bureau of Mines and the Truax-Traer Coal Company, some operating-scale experiments have been made with the cyclone thickener in the preparation plant of the Shamrock No. 1 mine at Kayford, West Virginia. These tests were made with a 14-in. cyclone of the type developed by the Dutch State Mines in Limburg. It was applied experimentally to the thickening of solids in washery water to obtain performance data to show the range of sizes that may be recovered and other operating characteristics that would indicate the field of usefulness of this device in coal preparation practice. This is a progress report only. It covers results obtained in a series of 17 tests of the operation of what has been considered a unit of commercial size operating on suspensions of fine coal mixed with a relatively small amount of free impurities. The underflow material, after further dewatering in centrifuges, is a marketable grade of coal. The coal at Shamrock No. 1 is mined from the No. 2 Gas seam. It is made up essentially of a low ash coal suitable for byproduct use with one or more bands of splint coal of higher ash content suitable for industrial fuel. The washing plant was installed for the two-fold purpose of removing the free impurities incident to mechanized mining and to separate the run of mine coal into the two types. To accomplish these results it is necessary to make a separation at a specific gravity of about 1.4 to recover the byproduct coal and to separate the splint coal from refuse at a higher gravity. The coarse coal section of the washing plant was put into service about 10 months before the fine coal section was completed. Inadequate screening capacity in the raw coal preparation plant resulted in a portion of the fine coal being fed to the jigs. No provision for preliminary dedusting of the raw coal feed was incorporated in the design. Under the conditions in the initial operating period, separation at the desired lower gravity was not realized, apparently because of the presence of an excessive amount of fine solids in suspension in the wash water. Difficulty in wetting the fine coal may also have been a contributing factor. Additional facilities for the removal of the fine solids from the wash water was indicated. Information then available on the Driessen cone for this purpose was studied and a cooperative agreement with the Bureau of Mines for experimental work with a unit of standard size as developed by the Dutch State Mines was arranged. During the time required for construction of the cone it was found the addition of a small amount of wetting

Jan 1, 1950

By H. D. Hoskold

It was not for the purpose of asserting any superior knowledge or authority, but simply of clearing up, in greater detail, some points casually mentioned in Mr. Scott&apos;s able paper, that the writer entered, some two years ago, into the discussion which that paper initiated. In such matters there is always room for differences of judgment, as well as for additional data, which may modify or complete the conclusions even of the best authorities. Those who are immersed in the duties of practical administration or work in the field, and who, being remote from the great scientific national libraries, are obliged to rely on their private collections, and to supplement them by their recollections of earlier studies, labor under special disadvantages in such a discussion; and it must be to the scientific and engineering world a matter for gratitude that Mr. Lyman has been willing to give the benefit of his advantages in this respect. Mr. Lyman would, however, doubtless at once disclaim the conclusion that his masterly summary constitutes " the last word " on this subject, and welcome further evidence, comment and criticism, such as the various contributors may continue to offer. This, therefore, is the motive, and must be the excuse, of the introduction by the writer of the following observations. The Miners&apos; Dial.—Many years since, the writer employed a miners&apos; dial, older in type than Fig. 12,* but without any attached spirit-level, made by Thomas Jones, a pupil of the great Ramsden. Jones was one of the old London makers and opticians, and enjoyed great reputation for accuracy in the con-

Jan 1, 1902

By G. L. Oldright, F. S. Wartman, H. E. Keyes

The economic manufacture of sulfuric acid by the ordinary chamber process usually involves production on a large scale and a plant that is costly to construct. The nature of sulfuric acid makes it costly to transport any great distance. For these reasons, the metallurgist has not found it feasible, at times, to beneficiate ores amenable to leaching, and a need exists for a local process that will produce acid cheaply on a small or large scale. To leach ores containing residual sulfides, an oxidizer, such as ferric sulfate, is needed in solution. Precipitation with scrap iron is one of the cheapest methods of removing some metals from solution, giving a plant of low first cost and supplying a source of cheap ferrous sulfate. The other ingredient needed for the process is SO2 roaster gas, the addition of which, as described below, will give both ferric sulfate and sulfuric acid. Where roaster gas is a waste or obnoxious product, the expense for materials is still further lessened. The use of ferric sulfate and sulfuric acid as a solvent lends itself well to the utilization of scrap iron as a precipitant, and the stages of the process fit in well together as an economic whole. Applications The hydrometallurgist usually thinks of ferric sulfate as a partial solvent for some of the sulfides of copper alone, as most work has been done on this metal. The processes of Hannay and Christensen, for leaching unroasted galena with ferric chloride made by anodic oxidation, show the added solvent action given by "ic" salts when added to brine solutions. It was found by R. D. Bradford (in some work to be published soon by the University of Utah) that, by the addition of a ferric salt to a brine solution, the silver as well as the lead in an unroasted semi-oxidized ore could be largely dissolved. The "ic" salt in the case of silver has evidently the same effect as the case of cupric sulfate when

Jan 1, 1926

By F. M. Stewart

A paper by Hurst and van Ever-dingen in 1949 led to the practical solution of many nonsteady-state flow problems.&apos; Subsequently, applications of this material have been discussed by several authors. The purpose of this note is to outline a simplified direct procedure for water-influx pressure predictions for pressures above the bubble point. The prcposed procedure is unique in that after the "time-conversion factor" and the "influx constant" are obtained, predictions are made without trial and error. The elimination of trial and error is made possible by expressing certain PVT characteristics as explicit functions of pressure. The procedure is applicable to fields producing at pressures above the bubble point and under radial water drive from an infinite aquifer. In the usual applications it is required to predict (1) withdrawals given future pressure history or (2) reservoir pressure, given future withdrawals or production. The theory, assumptions and conditions under which the nonsteady-state solutions hold are covered in the references and are not repeated. The simplified direct procedure outlined here has been developed from published solutions for the so-called "pressure case". A similar direct procedure for the same special conditions has been developed for the "rate case"; however, in this instance the procedure is lengthy and offers no advantage over the trial-and-error solution. Consequently, this paper covers only the procedure based on the pressure case. DISCUSSION Under the pressure case prediction of withdrawals from a water-drive field, given the future pressure history, involves the use of a nonsteady-state water-influx term together with the material balance equation. The solution of a particular problem requires the following steps: (1) division of past pressure and production data into equal time intervals; (2) computation of cumulative water influx vs pressure drop for each time interval of past history using the material balance equation; (3) determination of the best values for the "time-conversion factor" and the "influx constant" by equating the nonsteady-state influx term with the influx computed in Step 2 (this requires a trial-and-error procedure); (4) prediction of influx for a given pressure drop using the influx term and the computed factors from Step 3; and (5) calculation of fluids produced using the predicted influx in the material balance equation. A forecast of the water-oil ratio or water production rate is required to complete the calculation. It is assumed that a reliable estimate of original oil in place is available, as well as the production and pressure history, and data on reservoir fluid characteristics. If the original oil in place is unknown, it may be computed simultaneously with the tinie-conversion influx factors2,3. However, the oil in place so computed may be considerably in error3; consequently, it is usually preferable to use oil in place estimated from pore-volume data unless there is considerable doubt as to its accuracy. The Material Balance Equation Above the Bubble Point Above the bubble point the simpli-

By David L. Holt

The contribution of grain boundary shear to total elongation, CS/E&apos;, has been measured in an Al-Zn eu-tectoid alloy that was quenched from above the invariant temperature, then annealed at 250° C to a grain size of&apos; 1.8 p. At 250°C, ks/E&apos; is low at both high and low strain rates, but reaches a maximum, estimated as 60 pct at an intermediate rate of 5 X 10 per rnin. Rate sensitivity, as measured by the index m = a log a/a log E&apos;, follows the same trend, and furthermore the maximum values of m and -cur at approximately the same strain rate. This result, combined with the metallographic observation that boundary migration enhances boundary shearing, is interpreted as supporting a previous suggestion that the high rate sensitivity characterizing super-plasticity is the result of combined boundary shearing and migration. It is suggested that the latter event relieves stress concentrations at triple points, and smoothes boundaries so that stress is governed largely by a viscous boundary shear. GrAIN boundary shear has been considered in relation to superplasticity in several recent papers.&apos; The problem has been to explain the high strain rate sensitivity of flow stress, and the variation of rate sensitivity with strain rate (E&apos;) and grain size (L). The requirements for superplasticity, small L and high T, suggest the reasonableness of an approach to high rate sensitivity involving grain boundary shear. Further support came from experiments on the A1-Cu eutectic alloy,&apos; where it was found that strain rate sensitivity of cast material annealed to produce an equiaxed, micron-size grain is always low; taking as an index of rate sensitivity m = a log a/a log <, m < 0.3. However, m in hot-worked alloy of comparable grain size can be as high as 0.7. In the cast and annealed material, each phase is a single crystal, the only boundaries are interphase boundaries, and it is, consequently, geometrically impossible for boundary shear to contribute to deformation in any major way. Other observations (for hot-worked material) were a-L at constant (low) strain rates and indications that the rate of recrystallization was enhanced as strain rate increased. As a result of this work, it was proposed that high rate sensitivity arises from a deformation mode of boundary shear associated with boundary migration. Migration serves to relieve stress concentrations at triple points, and smoothes boundaries so that they assume properties of fluid films. On the other hand, the low rate sensitivity observed at high and low strain rates reflects deformation of bulk material. Measurement of the variation of grain boundary shear with strain rate and m have not yet been made. Such measurements are important, especially in view of a proposal, differing in detail from the above, that high m arises merely from a transition between a grain boundary shear mode of deformation at low rates to a transgranular mode at high rates.2&apos;4 In the present work, the contribution of boundary shear to total deformation is measured and in addition metallographic observations are made on surfaces of deformed specimens to look at the interaction between boundary shear and migration. The Al-Zn eutectoid alloy was chosen for its homogeneous, fine-grained structure, which is obtained readily without hot-working. It has also been the subject of a previous phenom-enologically directed study. EXPERIMENTAL Material. Compression specimens, cross section 4 by + in., length \ in., were machined from a sand-cast ingot of composition 77.5 wt pct Zn, 22.5 wt pct Al. (The melt was prepared from 99.9 pct Zn and 99.99 pct Al.) After homogenization at 375°C for 50 hr, the specimens were quenched in brine and removed before the heat evolution that accompanies de -composition of the high-temperature phase.5&apos;6 The resulting microstructure, see Fig. l(a), was too fine for grain boundary sliding to be easily studied; coarser structures were obtained by annealing for various times at 2 50°C. Annealing was terminated by a brine quench. Final average intercept lengths between all grain boundaries (both interphase and those lying in a phase), L, were: 0.5 p [annealed for 15 min, Fig. (a)], 0.8, 1.1, and 1.8 p [Fig. l(b)l. Testing Procedure. An Instron machine was used for most of the compressive deformation. Tests were of two types: those in which crosshead velocity was changed in steps to measure m as a function of strain rate15 and tests at constant velocity to a fixed (engineering) strain of -0.2 (20 pct). Stress reached a steady-state value (a) which was plotted, on a logarithmic scale, against log strain rate (E&apos;). An alternate and equivalent evaluation of m was to take the slope of the log o vs log 6 curve. Time at temperature before testing was 15 min. Strain rates covered by the Instron (4 x lo-&apos; to 4 x 10&apos; per min) were insufficient; at a higher rate of 5 x lo2 per min a gas-operated testing machine was used, the gas driving a piston to compress the specimen at a controlled velocity.&apos; To obtain points on the log a vs log E&apos; curve at low rates, specimens were compressed by a dead weight. strain rate was an average value computed by dividing strain at the end of test by loading time. In some tests strain was measured at fractions of the loading time; creep rate was found to be reasonably constant.

Jan 1, 1969

By W. A. Roper

Since 1950, several papers have been published which have described various methods for studying mobility ratio effects. The methods which have been described for studying mobility ratio effects include X-ray shadowgraph techniques, stepwise potentiometric model procedures, stepwise numerical procedures, gelatin model studies and fluid mapper model studies. The purpose of this paper is to describe a procedure for using a resistance network for studying mobility effects. DESCRIPTION OF APPARATUS The basic unit of the experimental model consisted of a network of 840 resistors fastened to a sheet of black Lucite which was mounted on a wooden frame, Fig. 1. The dimensions of the Lucite sheet were 36 X 36 in. The resistors were fastened to the Lucite sheet at mesh points by means of snaps. The mesh points were arranged in a square pattern, 30 X 30 in., spaced at intervals of l1/2 in. The snap fasteners permitted several resistors to be "stacked" in parallel. By adding additional resistors to the basic unit, the specific resistance on each side of the flood front could be varied. The square network of resistors represented one of four symmetrical elements of a five-spot well pattern. The current input was analogous to an injection well and the current output was analogous to a production well." The power supply was essentially a full wave transformer-rectifier system for converting alternating-current into direct-current. The DC voltage could be varied from 41.43 to 290 v in steps of 41.43 v by selecting the proper outlet jacks. The major components of the power supply were: a Triro power transformer, R 11-A; a dual 5Y3 vacuum tube; two gas filled OD-3 tubes; and a Triplett voltmeter, model 227-1, range 0 to 500 DC v. The voltages at the mesh points were determined with a Keithley electrometer, model 210, No. 185, manufactured by Keithley Instruments, Cleveland, Ohio. A Heathkit vacuum tube volt-

By H. D. Williams, R. A. Scriven

The distribution of elevation angle of finite plane facets distributed symmetrically about a given axis is derived in terms of the angular distribution of lines which these facets produce in a plane section parallel to the axis. It is assumed that the facets are not markedly elongated in preferential directions. The theory is intended for application to the angular distribution in polycrystalline metals of slip planes and of particular grain boundaries on which certain phenomena such as cavitation can occuv. Illustrative examples are given in closed form and simple numerical techniques are de-ueloped for practical application. The results are applied to the distribution of cavitated boundaries in a copper specimen after fatigue at 400°C and it is found that voids form on the boundaries that exper~enced maximum shear stress. When investigating the distribution of elevation angle between a given axis and planes symmetrically distributed about this axis the angular distribution observed in a plane section parallel to the axis is not necessarily the same as the required distribution. Consequently a technique for processing the results obtained by sectioning methods is required. An example where such a technique would find application is in the problem of intercrystalline void formation during uniaxial tensile creep. Two theories have been proposed to explain this cavitation in terms of the normal and the shear components of stress, respectively. Hull and Rimmer (1959) postulate that the growth of intercrystalline voids is controlled by the rate of supply of vacancies from the grain boundary, the local vacancy concentration being proportional to the normal stress on the boundary. Gifkins (1956) considers that slip arising within a grain causes a ledge to be formed at the grain boundary which is subsequently opened up into a cavity by grain boundary sliding. It might be possible to differentiate between these mechanisms by determining the angular distribution of grain boundaries containing cavities since the former theory predicts a predominance of cavitated facets normal to the stress direction whereas the latter should favor an angle of 45 deg to this direction. In a similar manner an indication may be obtained of the type of mechanism responsible for intercrystalline cavitation during high-temperature fatigue. Davies and Wilshire (1962) have analyzed the slip-plane distribution in a nickel specimen but the problem was not treated in any detail nor was any account taken of the finite extent of the planes being sectioned. Hilliard (1962) has given a very general account of how anisotropy in the microstruciure can be related to measurements taken in one or more plane sections by expressing both the measured and the true angular distributions as expansions in spherical harmonics.* The present analysis is con-

Jan 1, 1965

By Robert B. Sosman

THE chance that a Howe Memorial Lecturer will be able to refer back to a personal contact with the distinguished metallurgist for whom this lectureship is named grows steadily smaller. I did not have the pleasure of his personal acquaintance, but I did receive from him in 1916, quite unexpectedly, a letter commenting on a paper that I had recently published27 on "Types of Prismatic Structure in Igneous Rocks." The paper was written for geologists and petrologists, but it had an application, naturally, to the crystallization of iron and steel in a mold. The letter impressed me at the time, and still does, with the breadth of Professor Howe&apos;s interests and his perseverance in keeping up with the progress of any branch of knowledge that had metallurgical connotations. SCOPE OF THE LECTURE During several years preceding the date mentioned I had worked in collaboration with Arthur L. Day and E. T. Allen8 at the Geophysical Laboratory, Carnegie Institution of Washington, on the temperature scale as defined by the nitrogen thermometer at high temperatures. Later (1928-1947) I had the opportunity of helping to apply this experience to the pyrometric problems of the steel industry. Because of the range of its temperatures, the multiplicity of the methods used, and the variety of its purposes, pyrometry in the open-hearth process has always offered a fertile field for both research and development. I am therefore devoting an hour to the subject of temperatures in the basic open-hearth furnace, the furnace that makes most of our steel in the United States. I would direct your attention particularly to the choice of the first two words in the title of the Lecture. One sometimes hears or reads of the "temperature of such-and-such a furnace," as if it were a single, measurable, characteristic quantity. I need hardly emphasize to any one who has ever operated a furnace or a kiln that "temperature of the furnace" is a meaningless phrase. Even if we confine our attention to the space enclosed by the roof, walls, and hearth of an open-hearth furnace, it is doubtful whether any such space has ever been so uniform in temperature that the phrase would have a meaning. In any furnace, there are many different temperatures, capable of being measured at many different places, and actually being measured for several different purposes. These pyrometric purposes, methods, and results, if given in detail, would expand this lecture into a book on the basic open-hearth process. I must therefore confine myself to a statement of the range of temperatures as they have been observed in various parts of the furnace, indicating in a general way why they are measured, and mentioning the methods that are available without attempting to describe these

Jan 1, 1948

By John J. Croston

IN the closing months of 1936 the copper industry gave every evidence that it was at last on the threshold of an improved era. At the beginning of the year prices stood at 9 ¼ ¢, which in itself was a great improvement over prices prevailing for the three previous years. Industry generally was showing signs of moving forward in this country, and business was definitely good in certain foreign quarters. The threat of war and preparations for rearmament in Europe and Asia acted as a further stimulus to purchasing. By midsummer the situation had so improved and stocks had been so reduced that the cartel of foreign producers (including American producers with foreign mines) decided to increase the production quota to 75 per cent on Aug. 1. Large-scale buying gave continued strength to the price and by Oct. 1 the quota was increased to 80 per cent, and again on Oct. 15, to 85 per cent. Notwithstanding this the price of copper continued its advance and on Nov. 1, with stocks declining continuously, the cartel increased operations to 95 per cent, then to 105 per cent on Nov. 5. In the meantime the domestic producers, because of the great increase in home consumption, had increased their production by nearly one-half. At the close of the year copper sold at 12¢ per pound, and since the turn of the present year has reached 17¢. This rapid increase has not been wholly justified. Much of the increase was due to the legitimate demands of recovering industry, but rearmament orders plus accumulation of reserve stocks in case of war, purchases in anticipation of labor strikes and purely speculative activities on the London Metal Exchange accounted for the balance. Certainly in view of the state of industry and the general world price level, it appears unnecessarily high. Talk of a copper shortage is sheer nonsense, the recent condition in the market being created by overbuying, leaving but a small volume for speculative supplies. It takes some months for an increase in mine output to reach the market, but production is again overtaking apparent consumption, stocks have begun to increase, and this, together with the reopening of many small

Jan 1, 1937

By R. H. Maes, R. E. de Strycker, J. J. Jacobs

A simple method, based upow density measurements, has been perfected in order to determine the critical temperature of liquid miscibility gaps. Applied to the Pb-Cu system, it yielded a value of 980"C for the critical tempevature of the miscibility gap in this system. In the Pb-Cu-As system, the immiscibility between lead and coppev evolves towards a miscibility gap be-tween lead and copper arsenides; the liquation temperatures were determined joy different avsenic contents and values up to 1065°C were found. Combining these results with those given by the clzemical analysis of liquid samples taken at dqj.event temperatures, it has been possible to make a cowzplete determination of the liquid miscibility gap in this ternary system. In the Pb-Cu-Fe-As system, a ternary miscibility gap has been discovered; for some compositions, the molten and slowly cooled alloys separated into three layers: an Fe-As alloy, a Cu-As alloy, and a lead-rich layer. ThE Pb-Cu-Fe-As system is of interest for the study of the behavior of speiss or arsenical alloys in the lead blast furnace. The speisses produced in lead metallurgy generally have complex compositions, but they may be considered, in a simplified way, as a mixture of copper, iron, nickel, and cobalt arsenides; there is often an excess of metallic constituants, and lead is also present. Speisses liquate from lead at various temperatures according to their composition; according to industrial experience, iron speisses are already distinctly separated from lead bullion at temperatures of the order of 1100°C, whereas copper speisses only begin to liquate from lead at much lower temperatures, near their solidification points, which were never accurately determined until now. Besides these considerations of practical interest, the present study is of importance for the knowledge of liquid miscibility gaps. Particularly the data of the literature about critical temperatures of liquation are incomplete and present sometimes considerable disparities; a method has been perfected in the present work to determine these temperatures with accuracy. MISCIBILITY GAP OF THE LEAD-COPPER SYSTEM Review of Literature. The generally admitted outline of the Pb-Cu equilibrium diagram is shown by Fig. 1. This figure, with its numerical indications, is taken from the review of Hansen and ~nderko;&apos; compositions are given in weight percent, as will be the case in the remainder of this paper. Between 36 and 87 pct Pb, Pb-Cu alloys separate into two layers, in the liquid state. The critical temperature of liquation has been much disputed in earlier studies, where values up to 1500°C were claimed; but a reliable study of ~ohnen,&apos; based upon differential thermal analysis, gave a value of 990°C; this rather low value was verified by a recent study of Schiirmann and Kaune? based upon thermodynamical properties of the Pb-Cu alloys, which predicted a value of 1002°C. Liquid miscibility gaps were also studied by means of chemical analyses. Satisfactory results were generally obtained with the method consisting in taking samples of the two liquid layers in equilibrium and submitting them to chemical analysis; however, this method becomes delicate near the critical temperature. With this technique, Friedrich and waehlerts ob-

Jan 1, 1968