Search Documents

By C. H. Li, R. J. Stokes

This paper compares the fracture behavior of tungsten rods in three conditions: recrystallized. recovered, and wrought. Notched specimens suhjected to a 50 in.-lb impact load showed ductile-brittle transitions at 700, 4.90°, and 440°C, respectinely. The recrystallized material had an equiaxed pain structure and jracbred by simple cleavage from a grain boundary source at all temperatures up to 700°C. The wrought and recovered material had an elongated fibrous structure and at low temperatures fractured by cleavage originating from the notch. As the transition temperature was approached cleavage was preceeded by more and more intergvanular splitting which deflected the crack front into planes parallel to the tensile axis. The enhanced toughness of wrought and recovered tungsten was attributed both to its inability to initiate cleavage because no pain boundaries were suitably oriented perpendicular to the tensile stress and to its inability to maintain cleavage because of intergranular splitting ahead of the crack. It has been appreciated for a long time in a qualitative manner that the room-temperature brittleness of fully recrystallized tungsten may be alleviated by working the material at relatively low temperatures.' More recently this difference in mechanical behavior between wrought and recrystallized tungsten has been examined quantitatively by measurement of the tensile properties as a function of temperature. In these experiments brittleness has been expressed in terms of ductility or reduction in cross-sectional area upon tensile fracture or in terms of the bend radius before fracture under bending.' This work has shown the existence of a fairly sharp transition from brittle to ductile behavior with an increase in temperature. The ductile-brittle transition temperature for recrystallized material is approximately 200°C higher than for wrought material. An increase in strain rate, small additions of impurity,' or an increase in grain size4 shift the respective transition temperatures to higher values, but the difference between them remains approximately the same at 200°C. A number of explanations for this embrittlement by recrystallization have been given. It has been blamed either on the concentration of impurity at the grain boundaries, the increase in grain size, or the change in texture which occurs upon recrystallization. The present paper examines the effect of different heat treatments on the notch-impact behavior of commercial powder-metallurgy tungsten rods. The change in the ductile-brittle transition temperature for this method of loading and the fracture mode has been related to the different mi-crostructures produced by heat treatment. EXPERIMENTAL PROCEDURE Commercial swaged powder-metallurgy tungsten rods 1-3/8 in. in length and 1/8 in. in diameter were machined to introduce a sharp V notch 0.030 in. deep. To change the microstructure from that of the as-received wrought material some of the specimens were subjected to an anneal in nitrogen either at 1300° or 1400°C for 8 hr or at 1600° or 2000°C for 1/2 hr. The notched rods were then placed in a miniature Charpy-type impact machine and struck at their midpoint (opposite the notch) with a hammer designed to deliver 50 in.-lbs of energy. The strain rate at the base of the notch was estimated to be approximately 100 sec-1 at the instant of impact. The specimens were heated in situ to the desired impact temperature. The microstructures produced by the various anneals were studied by both X-ray diffraction and metallographic techniques. Fig. 1 reproduces the microstructures observed metallographically following a 10-sec electroetch in a 10 pct KOH solution. Fig. l(a) shows the elongated fibrous grain structure of the as-received material. Following the anneal at 1300" or 1400°C the grain structure was still elongated as shown in Fig. l(b) but the etch pits delineated dense polygonized dislocation arrays within many of the grains. Occasionally a relatively dislocation-free recrystallized grain was found growing into the matrix. The anneals at 1600° and 2000°C resulted in complete recrystallization and some grain growth. The grains produced at 1600°C were still slightly elongated as shown in Fig. l(c) whereas the anneal at 2000°C produced equiaxed grains. The changes in grain size produced the expected changes in the X-ray back-reflection patterns; there was no indication either in the as-received material or the annealed material of any preferred orientation. RESULTS a) Impact Behavior. Fig. 2 reproduces the ductile-brittle transition curves measured in the manner described in the previous section. It can be seen that under these testing conditions the as-received

Jan 1, 1964

By R. G. Davies, P. Beardmore, T. L. Johnston

The flow stress of a series of Ni-Cr-A1 alloys consisting of a dispersion of y' (based on Ni3Al) in a rnatrix of nickel-base solid solution y has been measured at temperatures up to 950°C as a fwzction of the volume fraction of y'. At high temperatures the flow stress is controlled by the amount of Y' in the alloy, i.e., the higher the volume fraction of y', the greater is the flow stress. This simple relationship is not obeyed at low temperatures in so far as a peak in the flow stress-volume fraction relation occurs at about 25 pct y'. The variation in the mechanical properlies of these alloys as a function of both temperature and volume fraction of y' has been correlated with changes in distribution of both the dislocations and y'. The results are interpreted on the basis that at low temperatures the y matrix is strengthened significantly bv the presence of a hyperfine y' precipitate due to decomposition on cooling; at high temperatures the y matrix is a single phase of low strength. It is clearly recognized that the high temperature strength of most nickel-base superalloys depends upon a dispersion of the ordered fcc phase y', based on Ni3A1, in a fcc solid solution matrix y based on nickel. Although the volume fraction of y' varies widely from about 0.2 in Nimonic 80A to about 0.6 in Mar-M200, all such nickel-base alloys manifest an unusual insensi-tivity of the flow stress with respect to temperature. In Mar-M200 for example, the 0.2 pct flow stress remains essentially constant from room temperature to 750°C. The conclusion has been drawn1 that the characteristically low temperature dependence of the flow stress of y-y' nickel-base alloys is obtained when the state of dispersion of y' is such that dislocations are forced to cut through the y' particles at the onset of yielding. When the spacing between the y' particles is so large that the flow stress is controlled by dislocation bowing between particles, then the initial flow stress decreases progressively with an increase in temperature at a rate determined by changes in elastic properties. The same conclusion is inherent in the detailed, mechanistic model of the deformation process in commercial superalloys which has been developed by Copley and ear' in which the temperature independent flow stress is attributed primarily to the contribution of the antiphase boundary energy created in the y' particles during deformation. In this theory the temperature insensitivity of the flow stress is a reflection of the constant antiphase boundary energy as a function of temperature. An important microstructural parameter that is relevant to the explanations that have been suggested' to account for the temperature insensitivity of the flow stress is the volume fraction of y'. To vary the latter to any significant extent in a given commercial alloy is clearly difficult. However, it is possible in a relatively simple Ni-Al-Cr ternary system which manifests analogous microstructures in terms of the distribution of y' in y and contains specific alloys which have flow properties that depend on temperature in a manner quite similar to their more complex commercial counterparts. Hornbogen et . have studied precipitation phenomena and deformation mechanisms in such alloys but only where the y' volume fraction was small (less than 0.2) and the y' particle size varied from less than 100A up to a maximum of -1000A. In the present study, a series of alloys was prepared in which the volume percent of y' at 900°C was varied from 0 to 100 pct with the y' particle size (of the order 0.5 p) comparable to the sizes obtained in commercial superalloys. Particular attention has been given to the relationship between variations in the volume fraction and distribution of y' and the temperature dependence of the flow stress EXPERIMENTAL TECHNIQUES The Ni-Cr-Al system was selected because it is well characterized, bears a close relationship to commercial alloys, and offers the advantage of an extra degree of freedom over a binary system. In the present investigation, a series of alloys across the tie line between NisA1 and Ni3Cr (Ni3Cr is not an in-termetallic compound, the nomenclature is only used to designate the composition) were vacuum cast. The pseudobinary6 and the composition of the alloys used are shown in Fig. 1. It is important to note that the compositions of the y phase and the y' phase in the two-phase alloys was always the same. Alloy compositions were selected from the binary diagram, Fig. 1, in order that aging at 900°C would produce from 0 (100 pct y) to 100 pct y' by volume percent. (The size of the y' particles produced during the equilibrium aging treatment increased as the volume fraction of y' increased, ranging from about 0.2 p at low volume fractions up to about 0.8 p at the highest volume fraction.) The y' phase is based on the inter-metallic compound Ni,A1 which has the fcc LIZ type superlattice structure, and chromium substitutes for aluminum in the structure. The y phase is a disordered fcc solid solution. The alloys were heat treated at 1150°C for 2 hr, air cooled to room temperature, and finally annealed for 16 hr at 900°C. The rods were then centerless ground to 0.25 in. diam and cut into compression samples 0.5 in. long. The compression tests were made on an In-stron machine at a strain rate of 7 x 10"4 sec-'. A rapid heating radiant heat furnace was used which minimized the heating and temperature stabilization time to 10 min for the highest testing temperature. All the tests were stopped after 5 pct plastic strain.

Jan 1, 1970

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to in- crease. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining

Jan 1, 1981

By Daniel J. Martin, James L. Martin

The dendritic pattern of steels shown by deep etching is used extensively as a guide in the inspection and control of the great majority of steels used in ordnance construction and for many applications in industry. The value of macroexamination lies in the fact that it enables a qualified observer to make deductions concerning the general quality of relatively large pieces of metal. Not the least of these general characteristics is the nature and extent of the dendritic segregation in the steel, either in the cast condition or after mechanical or thermal treatments. Previous Work Detailed methods for macroetching were outlined by Yatsevitchl and have been standardized by the American Society for Testing Materials. A comprehensive study of the occurrence, origin, and the chemical and crystalline nature of the dendritic structure was given by Keshiam2 The marked persistence of dendritic segregation in nickel steels is fully recognized and has been discussed by Sauveur and Reed3 and by others. Very little, however, has been written on the effect of the various elements on the macrostructure of steels, and the purpose of this report is to submit evidence concerning the influence of chromium, nickel and molybdenum on the macrostructure of some 4 by 4-in. ingots cast and treated under closely controlled conditions. Methods and Results The ingots to be described were made in a 60-lb. high-frequency induction furnace at the Watertown Arsenal. Heats were made from a single lot of materials; were molten for the same length of time; tapped at approximately the same temperature into a standard mold preheated in each case to 150º ± 10º C.; and stripped and buried in ashes after 10 min. in the mold. Transverse disks were taken from the same location in

Jan 1, 1939

By T. L. Joseph

LARGE deposits of manganiferous iron ores, representing several million tons of metallic manganese, occur in the United States. The Minnesota deposits of such ore-are of outstanding importance because of their size, state of development, ease of mining and proximity to the Great Lakes, which permits water transportation to steel centers. In' view of the fact that our steel industry requires large quantities of manganese, for which no satisfactory substitute-has been found, and because our reserves of ferro-grade ore are comparatively small, the development of methods that will make our large deposits of manganiferous iron ores available as a source of ferromanganese is an important problem. Realizing the importance of this problem, some years ago the North Central Station of the U. S. Bureau of Mines and the Minnesota School of Mines Experiment Station undertook jointly the development of methods for recovering the manganese content of manganiferous iron ores in a: form suitable for the production of ferromanganese, the 80 per cent. alloy indispensable in producing steel. Two types of manganiferous iron ores have been described in previous reports. I The brown ores are higher in iron and lower in manganese than the black ores; the black ores are more siliceous but contain less phosphorus. The utilization of the iron content of the brown ores in the production of steel appears to furnish the best basis for their treat-ment. The method of attack has been to work out modifications in iron and steel practice so as to recover manganese in the form of slag comparable to ferro-grade ores. The greater part of the experimental work has been conducted with a 6-ton blast furnace and a Y2-ton basic open hearth. This paper is devoted mainly to open-hearth tests in which high-phosphorus spiegel

Jan 1, 1930

By James L. Martin, Daniel J. Martin

The dendritic pattern of steels shown by deep etching is used extensively as a guide in the inspection and control of the great majority of steels used in ordnance construction and for many applications in industry. The value of macroexamination lies in the fact that it enables a qualified observer to make deductions concerning the general quality of relatively large pieces of metal. Not the least of these general characteristics is the nature and extent of the dendritic segregation in the steel, either in the cast condition or after mechanical or thermal treatments. Previous Work Detailed methods for macroetching were outlined by Yatsevitchl and have been standardized by the American Society for Testing Materials. A comprehensive study of the occurrence, origin, and the chemical and crystalline nature of the dendritic structure was given by Keshiam2 The marked persistence of dendritic segregation in nickel steels is fully recognized and has been discussed by Sauveur and Reed3 and by others. Very little, however, has been written on the effect of the various elements on the macrostructure of steels, and the purpose of this report is to submit evidence concerning the influence of chromium, nickel and molybdenum on the macrostructure of some 4 by 4-in. ingots cast and treated under closely controlled conditions. Methods and Results The ingots to be described were made in a 60-lb. high-frequency induction furnace at the Watertown Arsenal. Heats were made from a single lot of materials; were molten for the same length of time; tapped at approximately the same temperature into a standard mold preheated in each case to 150º ± 10º C.; and stripped and buried in ashes after 10 min. in the mold. Transverse disks were taken from the same location in

Jan 1, 1939

By J. C. Melrose

The contact angle is one of the boundary conditions for the differential equation specilying the configuration of fluid-fluid interfaces. Hence, applying knowledge concerning the wettability of a solid surface to problems of fluid distribution in porous solids, it is important to consider the complexity of the geometrical shapes of the individual, interconnected pores. As an approach to this problem, the ideal soil model introduced by soil physicists is discussed in detail. This model predicts that the pore structure of typical porous solids will lead to hysteresis effects in capillary pressure, even if a zero value of the contact angle is maintained. The model is generalized to situations in which the contact angle takes on values between zero and 40 degrees. For the imbibition branch of the capillary- pressure function, the model predicts a considerable departme ftom the usually assumed cos 0 relationship. In fact, according to the model, it is possible that a displaced wetting phase will not be able to reimbibe, even when the contact angle does not exhibit hysteresis. INTRODUCTION The subject of capillarity in porous media has long been of interest in many branches of engineering and applied science. The earlier investigators were those concerned with the physics of soils. 1-5 More recently, petroleum engineers and others dealing with the problems of petroleum production from reservoir rock have given much attention to the subject.6-10 Also, important additions to the literature of capillarity have been contributed from the field of chemical engineering.11-12 These attest to the wide range of industrial applications in which capillary phenomena play a role. The present paper is concerned with the role which wettability plays in capillary action in porous media. As is well known, capillary-rise (or capillary pressure) phenomena have frequently been interpreted with the aid of a model employing the concept of a cylindrical capillary tube. This approach has enjoyed a certain degree of success in correlating experimental results.13 The generalization of this model, however, to situations which involve varying wettability, has not been established and, in fact, is likely to be unsuccessful. In this paper another approach to this problem will be discussed. A considerable literature relating to this approach exists in the field of soil science, where it is referred to as the ideal soil model. Certain features of this model have also been discussed by Purcel114 in relation to variable wettability. The application of this model, however, to studying the role of wettability in capillary phenomena has not previously been attempted in detail. In the present paper, additional features of the model are introduced. These features are critical in determining the quantitative behavior of the model. GENERAL FEATURES OF CAPILLARY HYDROSTATICS BASIC PRINCIPLES When the interstices of a typical porous solid are occupied by two or more immiscible fluid phases, the fluids are microscopically commingled. Hence, fluid-fluid interfaces are found within a certain fraction of the pore openings. The fundamental equation of capillarity specifies the configuration of these fluid-fluid interfaces. This is known as the Laplace equation, when derived from mechanics, and as the Gibbs-Kelvin equation when derived thermodynamically.15 Given two fluid phases, a and ß, in hydrostatic equilibrium, the Laplace equation states that the respective fluid pressures in regions close to the interface are related by Here oaß is the surface or interfacial tension and rl and r2 are the principal radii of curvature of the surface or interface. The pressure difference, Pa-Pß, is the capillary pressure, PC. As Buff15 has shown, Eq. 1 states the condition for hydrostatic equilibrium within the two-phase confluent region, which is referred to as the interface. It thus can

Jan 1, 1966

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944

By L. Weyher, H. L. Lovell

This discussion is restricted to a very specific application of the cyclone - its use as a hydro-cyclone in the cleaning of fine coal. It is hoped that the development of the present data will assist in the further elucidation of existing qualitative models, and also in an enhanced application of the hydrocyclone and provide a base for further research. Discussed are the mechanisms of gravity separation in hydro-cyclones, test procedures, experimental observations, and industrial applications from these studies. Within the general area of unit operations, a considerable effort has been expended in theoretical and empirical research associated with cyclone operations. The motivation involves the industrial requirement for devices and techniques to manipulate small particles at low operating costs, a situation required in coal preparation. There are good reasons why the cyclone helps to satisfy this demand, because it combines operational simplicity (no moving parts) with versatility and high throughput capacity per unit area. The cyclone is one of the most widely applied tools in the process technologies. There are areas for potential cyclone application which have been only meagerly explored or not considered at all. This discussion is restricted to a very specific application of the cyclone - its use as a hydrocyclone in the cleaning of fine coal. It represents an initial presentation of a more comprehensive report. Coal preparation can appropriately claim the hydrocyclone since most of its predominant industrial uses have originated in this area and have spread into other applications, including the broad field of ore dressing, the petroleum industry, chemical processing, nuclear engineering and food technology. There is one operational principle common in all cyclones: A fluid is tangentially introduced into a cylindrical or conical container under pressure. A predominantly irrotational flow field1 is established within the cyclone (Fig. 1). The uniqueness of this flow is indicated by the variation in tangential velocity across the cyclone radius, which reaches a maximum a short distance from the center and decays toward the cyclone wall. In contrast, the tangential velocity in a centrifuge increases uniformly toward the wall. Usually two products are discharged from the cyclone. They differ in that one discharge consists predominantly of that portion of the feed fluid which moves along the wall axially away from the feed inlet, while the other consists predominantly of fluid spiralling along the central regions of the cyclone, in an axial direction opposite to that of the wall current. Fig. 2 indicates these discharge points schematically. The latter product may be termed the vortex-product, since it is discharged with the central vortex-current. In the case of conical cyclones, the former product may be referred to as the apex-product. Although the names "over- and underflow" are widely used, many cyclones are operated from extreme angular positions thus the proposed terms are less ambiguous. The cyclone feed fluid can be laden with solid particles or nonmiscible fluid drops. Such a feed component is discharged from the cyclone, after some residence time, into the one or the other product. Yet, the orifice through which a particle will leave the cyclone is dependent upon a number of factors. These factors, in a statistical sense, determine the path of the particle within the cyclone. Thus, different separation phenomena are possible and different process results attainable by the controllable variation of the particle path. It is then, to attain a fuller understanding of this particle path, to which this study is ultimately directed. It is anticipated that the detailed study of the data being developed will allow further elucidation of existing qualitative models. However, the development of a quantitative description of cyclone operation in terms of a mechanism is not currently feasible. The flow conditions in a cyclone are not fully understood even for a pure fluid, without the added complexity of the inclusion of multiple size-density particles. It is hoped that the development of the present data will also assist in an enhanced application of the hydro-cyclone and provide a base for further research. Some practical applications drawn from the data are suggested. Cyclone operations have been classified according

Jan 1, 1967

By Robert E. Green, T. Hinton

Expressions are derived for tke orientation factors appearing in the Grana to -Lucke theory of dislocation damping, for fcc crystals. The factors are given as functions of the elastic constants, the direction cosines of the specimen axis, atld the direction cosines of the particle displacemeizts, for darnping due to dislocation motion on each of the twelve possible slip systems as ixell as lor simultaneous dislocation rnotion on all twelve systems. RECENTLY Green' has outlined the general procedure for calculation of the modes of wave propagation in a single crystal possessing a given crystallo-graphic orientation. In addition he has suggested how the results of such calculations along with calculations of the resolved shear-stress factors for slip enable the orientation-dependent factors (orientation factors) appearing in the Granato-Lucke theory of dislocation damping to be calculated. However, reen' assumed that the maximum stress on dislocations was in the direction of the particle displacement of the elastic wave giving rise to the dislocation damping. The present cal'culations show that this is an oversimplified approach appropriate only to special cases of high crystallographic symmetry. The exact calculation of stress on the dislocations can only be obtained by resolving the nine components of stress associated with the elastic wave into the appropriate slip direction and then summing. In this paper the general expressions for orientation factors are derived for fcc crystals in terms of the elastic constants, the direction cosines of the particle displacements, and the direction cosines of the specimen axis, bearing in mind the point mentioned above. Equations are presented which give the orientation factors for damping due to dislocation motion on each of the twelve possible slip systems as well as for simultaneous dislocation motion on all twelve systems arising from elastic-wave propagation. These orientation factors are appropriate to attenuation measurements made by the pulse-echo technique, where the elastic wave is a traveling wave. They will be compared with those for the case of a standing wave as derived by Granato and Lucke which are appropriate to measurements of internal friction by the resonance technique. The expressions for the orientation factors are compared with the five values given by insruch,' based on unpublished work of Granato and Liicke, for positions of highest symmetry in the stereographic triangle. The various equations derived for modes of wave propagation and orientation factors have been evaluated for the case of aluminum crystals at 1-deg intervals throughout the stereographic triangle. These results will be presented in the form of contour diagrams in a subsequent paper3 and their relevance to ultrasonic measurements discussed. ORIENTATION FACTORS The coordinate system used for the calculations is shown in Fig. 1 and all specimen axes are taken to lie in the shaded standard triangle. The twelve slip systems are indexed according to Table I. Following the suggestion of lers, we may define the orientation factor Ok in the Granato-Liicke theory5 by the equation

Jan 1, 1967

By J. J. Frawley, W. J. Childs

The dynamic nucleation of supercooled bismuth and Bi-Sn alloys has been studied over a frequency range of 15 to 20,000 cps. For low-frequency vibration, a minimum vibrational energy was required for enhancement of nucleation. Above this critical energy, the dynamic supercooling was less than static supercooling showing that vibration promoted nucleation. The amount of dynamic supercooling continued to decrease with increasing vibrational energy until a minimum or threshold value was reached. This minimum value of supercooling for nucleation remained constant joy all further increases in vibrational energy. For higher frequencies, similar results were observed. This behavior has been related to the necessity of cavitation for dynamic nucleation. When a liquid is cooled to a temperature below its equilibrium melting point, the solid phase is more thermodynamically stable. However, for solidification to occur, a two-step process, nucleation and subsequent growth of the solid phase, must occur. When a liquid is supercooled, that is cooled below the equilibrium melting point, the controlling process for solidification to begin is the rate of nucleation. Once nucleation has occurred, the solidification process is controlled by the rate of growth. Nucleation can be induced by two factors: either by a catalyst or by the use of mechanical shock. Numerous investigators1-4 have studied the effect of nucleation catalysis but much less systematic study has been made of nucleation by mechanical shock waves. The influence of vibrations on grain size in castings and ingots has been studied by many authors but no clear understanding of the mechanism or accurate prediction of the effect has been presented.5 It would be intuitively expected that the further the departure from equilibrium (i.e., the greater the supercooling), the easier it would be to induce nucleation. This has been quantitatively demonstrated both by walker6 and later by Stuhr,7 that the greater the degree of supercooling the easier it is to nucleate by a shock wave. Stuhr also attempted to obtain the mechanical energy required for nucleation of bismuth as a function of supercooling. He vibrated a crucible containing supercooled metal at low frequencies and various amplitudes and noted the corresponding dynamic supercooling obtained. The amount of supercooling was inversely proportional to the mechanical energy applied. Limitation of his experiment was the problem of the confinement of the liquid in the crucible without splashing and minimizing other unwanted modes of vibration. Tiller et al.8,9 did similar work on tin and Sn-Pb alloys using an electromagnetic stirring device. Their conclusions were that the magnitude of the magnetic field strength did not affect the amount of undercooling at which nucleation was initiated. While conclusive experimental results have been lacking to explain this effect of mechanical vibration on inducing nucleation, a number of theories have been proposed. Two of these theories are discussed below. 1) The Change in Melting:- Point Locally Due to the Change in Pressure (Clapeyron Equation). According to Vonnegut10 the most plausible explanation for the nucleation of a supercooled melt by cavitation is the effect of changing the melting point by a change in pressure. For materials where the volume decreases on solidification, an increase in pressure raises the melting point; for materials which expand on solidification, the melting point is raised for a decrease in pressure, i.e., rarefaction. Using the Clapeyron equation, the melting point of a metal can be calculated as a function of pressure. If it is assumed that the equation can also be used to calculate the temperature of nucleation of a supercooled melt as a function of pressure (i.e., the temperature of heterogeneous nucleation will increase with pressure at the same rate as the melting point), the amount of supercooling required for nucleation will be constant at all pressures as shown in Fig. 1. It is obvious that an isothermal change which results in an increase in melting point results in an equal increase in supercooling. This increase in supercooling may now be sufficient for nucleation. A pressure of 80,000 atm was calculated, using the Clapeyron equation, as the pressure required to increase the temperature of nucleation of nickel by 200°C. According to Lord Rayleigh,11 this very large pressure could be generated for a very brief period of time by the collapse of a cavity. This pressure wave is radiated in all directions from the collapsed cavity. If the temperature of the melt is slightly below its equilibrium melting temperature at atmospheric pressure, stable growth can follow; that is, once nucleation occurs, growth becomes the main driving force of the solidification process. This proposal has been extended to water which expands on freezing by assuming that nucleation occurs during rarefaction following the pressure pulse. This negative pressure pulse should follow immediately after the positive pressure pulse with its magnitude approaching the critical tensile strength of the liquid. The negative pressure developed during this period would raise the melting point of water and thus promote nucleation. Hunt and jackson12 have suggested this for water. Similarly, it could be postulated that bismuth which also expands on freezing could be nucleated during the negative pressure pulse. 2) Nucleation by a High-pressure Phase. An extension of the Clapeyron equation to systems where density decreased on freezing at atmosphere pressure has been proposed by Hickling.13 The phase diagram for water initially shows the well-known decrease in

Jan 1, 1969

By R. V. McAfee

The fundamentals of vertical-lift performance are examined with the aid of computer-calculated flowing gradient charts. Flowing and gas-lift well performance characteristics are determined from available well test data. The effect of tubing size, gas-liquid ratio and wellhead pressure is discussed for both flowing and gas-lift wells. The effect of gas-injection pressure, formation gas, bottom-hole pressure and valve spacing is also discussed for gas lift wells. From these studies conclusions may be reached for improving or prolonging natural flow, obtaining optimum lift efficiency when natural flow ceases and improving existing gas-lift systems. The techniques perfected satisfy the requirement that the time involved to conduct an evaluation be practical for operating personnel. INTRODUCTION Flowing pressure gradients furnish the key to successful evaluation of vertical-lift performance in producing wells. Command of multiphase flow gradients in some readily usable form is a necessity before operating personnel can competently include vertical-lift performance evaluation of both flowing and artificial-lift wells in their over-all consideration of production efficiency. A readily usable form cannot be overemphasized since most of the decisions which confront the production engineer with a problem well must be made quickly. In moving a barrel of oil from the reservoir to the stock tank, the major portion of energy generally is expended in the vertical-lift phase. This may or may not be of concern during the flowing life of a well, depending upon the production requirements. It becomes of some concern when the flow performance of the well becomes erratic, and a conscious effort must be made to maintain natural flow. It is at this time that the first steps may be taken to modify existing conditions to relieve unnecessary limitations to proper flow. When natural flow ceases and some form of artificial lift must be installed, the amount of energy expended in lifting liquids becomes quite obvious. It is at this time, if no other, that lifting efficiency becomes important because that part which must be supplied from an outside source is now related directly as a cost per barrel of oil produced. Ten years ago, the majority of gas-lift wells were produced with gas-well gas. Today, the majority are produced by closed rotative gas-lift systems. This permits a direct evaluation of well performance in terms of horsepower requirements and has resulted in mixed conclusions as to the success of gas lift based upon the relative efficiency of a particular system. An increased awareness of the need to resolve vertical-lift performance on a readily usable, scientific basis was inevitable. An indication of the need for better applied science in this field is the often-asked question of whether or not gas-lift can efficiently deplete a given well or reservoir. This question cannot possibly be answered without first evaluating reservoir, surface and vertical-lift performance both as encountered today and as anticipated throughout the life of the well or wells. The technique presented in this paper was originally developed to upgrade gas-lift installation design from an applied art to an applied science. It has since been successfully used not only for this purpose, but also for the whole field of vertical-lift performance in its broadest sense. Lift efficiency should be considered important while the well is still flowing, as well as after natural flow ceases. Correct interpretation and proper modification of the vertical-lift performance of a producing well can provide dramatic improvement in production performance and/or efficiency. STATEMENT OF THEORY AND DEFINITIONS Fig. 1 illustrates the three divisions of production which will be used in this paper. The terms are a modified version of those presented in the very fine paper by Gilbert.' The fields of reservoir and surface performance both have been greatly improved over the years. A study of those writings which may be found indicates that the field of vertical-lift performance has not progressed as well. There are two possible reasons for this lack of progress. 1. It has not been recognized as a scientific field in itself by the oil companies, as has reservoir engineering. 2. The equipment companies have confined their efforts to mechanical design research rather than the more basic study of vertical-lift performance of producing wells. Both organizations must have an economic stimulus for doing research in this field, and most of the results obtained in past work has been so erratic as to arouse little enthusiasm. The basic purpose of interpreting vertical-lift performance is to predict operating conditions below the surface of the ground from available data. The success of the interpretation depends upon the accuracy with

By Robert Goodrich

EXPERIMENTS ON A PORPHYRY COPPER ORE FROM BISBEE, ARIZ. THIS research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward F. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. PETROGRAPHIC DESCRIPTION Texture: Variable. Fine to medium mixed aggregate. Original structure: Obscure. Secondary structure: Fractured; healed.

Jan 8, 1915

By T. E. Kihlgren

SYSTEMATIC data are presented on the relation of composition of nickel silvers to color, tarnish resistance, hardness and liquidus temperatures, for alloys containing up to 30 per cent nickel and 50 per cent zinc, further modified at certain nickel and zinc contents by 0 to 8 per cent of tin and 0 to 10 per cent of lead. Attention has also been directed, using a still more limited range of alloys, toward a study of tensile properties and such casting properties and characteristics as fluidity, shrinkage and pressure tightness. In some of these, rather broad ranges of composition are dealt with; in others, it has been expedient to focus attention on the Federal Specification 20 per cent nickel silver casting alloy, WWP-541. INTRODUCTION The demand for an alloy essentially white in color, which could be cast and worked by simple methods and which possessed strength and corrosion-resisting properties superior to the usual brasses, led to the discovery and early use of cupronickel alloys containing zinc, and some-times tin, lead and other metals. This type of alloy was generally known as German silver until the war, when the term "Nickel Silver" became generally accepted. The element principally responsible for the white color of the alloy and for its strength and corrosion resistance is nickel, which may constitute from 8 to 30 per cent of the alloy. The functions of the other elements will be described later. The manifold uses of nickel silver are largely due to its color, corrosion resistance, ease of casting, fabrication, joining and rather moderate cost. In many instances the alloy is finished by grinding and polishing while in others it may be finished with a silver or nickel plus chromium plate. Electroplates

Jan 1, 1935

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By B. Chalmers

THE practical importance of the phenomena of melting and freezing must have been recognized for a very long time. The difference between ice and water, for example, has had a profound influence on the history of mankind and the evolution of society. The possibility of melting a metal and allowing it to freeze in a mold of chosen shape has been an essential ingredient in our mastery of the art of shaping metals, and therefore in the evolution of the: machine age in which we find ourselves. The importance of melting and freezing, as applied to metals and alloys, has been so great, in fact, that empirical solutions have been found for the multitude of practical problems that have arisen. This approach has been so successful that relatively little attention has been directed to arriving at an understanding of the fundamentals of the processes. But metallurgy has come to a stage at which we may expect that some, at least, of the more complex problems that have not yet been solved (or perhaps even recognized) may be handled more effectively by scientific study, theoretical understanding, and logical experimentation than by trial and error. In this lecture, therefore, I propose to describe in outline what I think really happens when a metal freezes. In doing so I hope to explain many of the phenomena which have been observed, and in particular to account for the structures that are obtained in actual ingots and castings. The basic problem, to which this lecture represents a tentative partial answer, is this: a mass of metal, containing known proportions of various elements, is melted, heated to a given temperature, and then allowed to freeze under specified conditions. What will be the "structure" of the resulting metal? The term structure includes: 1—crystal size, shape, and orientations, 2—distribution of chemical elements, and 3-—shape, including cracks, cavities, pores, etc. The Solid-Liquid Interface We will first consider what takes place if a single crystal of a metal in the form of a rod is heated, not uniformly, but so that one end is hotter than the other. If this heating process is continued long enough, the hotter end will eventually melt; we will suppose that the rod is in a containing vessel so that the molten metal does not run away, Fig. 1. When some of the metal has melted, we have some solid, some liquid, and an interface or surface of contact between them. If the source of heat is now removed, the interface will move so that some of the liquid freezes, and if the supply of heat is suitably adjusted the interface will remain at rest. This very simple arrangement allows us to study the basic processes of melting and freezing, and if we fully understand this simple case, we may be able to account for what takes place under practical conditions where the heat does not all flow in the same direction, and where the heat flow is determined not by a controllable source of heat but by the heat capacity and temperature of metal and mold, and by the heat loss from the mold surface. The solid-liquid interface is evidently the region of the greatest interest to us; on one side of it there is crystalline solid, and on the other, liquid. In the solid, each atom has a well defined position, around which it vibrates as a result of thermal agitation. It only leaves this position in the relatively rare event of a "diffusion jump." The liquid is much less systematically organized. The atoms are about as far from their neighbors as in the solid, but the arrangement is much less systematic and is continuously changing. The solid and the liquid are represented diagrammatically in Fig. 2. The average energy of the atoms in the liquid is greater than in the solid by an amount that corresponds to the latent heat of fusion, i.e., the amount of heat that has to be supplied to convert unit mass of solid into liquid at the same temperature. The Two Processes As has recently been shown by Jackson and Chalmers,3 many of the features of the processes of freezing and melting can be understood if it is assumed that a continuous and rapid interchange of atoms between solid and liquid always takes place at a solid-liquid interface." It is necessary to con- sider two distinct processes, that of melting, in which atoms leave the surface of the solid and become part of the liquid, and the converse process,

Jan 1, 1955

By H. R. Gardner

The heat treatmmt of plutonium was studied using the Jominy end-quenching technique commonly used for determining the hardenability of steel. Plutonium specimens were end-guenched from temperatures in each of the ß, y, d, d') and E phases. One series of specimens with a low-iron content, 165 pprn Fe, and another gvoup with a high-iron content, 678 pprn Fe, were used in order to study the effect of a Pu-Pu,Fe eutectic network on the hardness and micro-structure. Hardness traverses indicated no significant variations in hardness with either cooling rate or quench temperature. Metallographic studies indicated major effects on microstructure. Grain size was found to vary markedly with quenching temperature and cooling rate. It was determined that the Pu-PueFe eutectic network could be modified extensively by heat treatment, including spheroi -dization in the y phase and 6 phase below 413°C. An unidentified spheroidal inclusion was observed to go into solution in the delta and higher temperature phases. 1 HE element plutonium is unique among metals in that it has six allotropic forms in the solid state.' These have been designated' as the a, ß, y, d, d', and phases. The respective phase transformations occur at approximate temperatures of 122", 210°, 319°, 450°, and 480°C with a melting point at 640°C. With this number of phase transformations it becomes pertinent to consider the effect of heat treatment and cooling rate in the various phases on the microstructure and hardness of plutonium. To determine; the effect of a wide range of cooling rates, the Jominy end-quenching technique was applied to cylindrical plutonium specimens. In addition, since the presence of iron in amounts greater than 500 pprn is common in plutonium and results in a network of the Pu-Pu6Fe eutectic, it was decided to study heat treatment effects on two bomb reduced plutonium buttons with different iron contents. A low iron button containing 165 ppm Fe and a high iron button containing 678 ppm Fe were selected for this comparison. EXPERIMENTAL PROCEDURE Experimental Material. The cylindrical bars for Jominy quenching were cast from button stock in vacuo in MgO coated graphite molds. Metal pouring temperature was approximately 950°C and the molds were preheated to 300°C. The castings were machined to 0.5 in. diam. by 2.5 in. long cylinders. Chemical analysis and density data for the two groups of Jominy specimens containing different iron contents are presented in Table I. Except for iron, heats 19-12-1 and 20-2-1 are comparable within the limits of analytical accuracy. Representative specimens from the low-iron and high-iron bars were taken for metallographic examination. The low iron specimen was found to have extensive microcracking, Fig. 1. In addition, numerous unidentified spheroidal inclusions were present, Fig. 17. The average grain size of the low-iron plutonium is 0.068 mm, Fig. 4. In the high-iron plutonium, a Pu-Pu6Fe eutectic network is prominent, Fig. 7. The average size of the network is 0.100 mm. Unidentified spheroidal inclusions were also common in the high-iron plutonium. The average grain size of the high-iron plutonium is 0.036 mm. Experimental Technique. A Jominy end-quenching fixture was fabricated for glove box use. A 2.5 in. water height was used with an orifice of 0.250 in. ID. The orifice to specimen distance was maintained at 0.5 in. Annealing temperatures of 160°, 265°, 400°, 465°, and 535°c were chosen for the study of the effect of quenching from ß, y, d, d', and e phases on microstructure and hardness. During quenching, cooling curves were obtained from the Jominy specimens at distances from the quenched end of 1/16, 1/8, 3/8, 3/4, 1-1/4, and 2 in. Cooling rate calculations were made from the cooling curves for temperature intervals of 100° to 110° 160" to 170°, 330" to 340°, 420° to 430°, and 490° to 500°c. These temperature intervals were chosen

Jan 1, 1962

By Arthur F. Daily

8.5-1. Bucket Line Dredge. INTRODUCTION. The modern bucket-line dredge for mining placer deposits is a combined floating excavating machine and a gravity concentration system. Material is excavated at the forward end by the buckets, elevated, washed and screened, concentrated for recovery of valuable mineral, and discharged off the stern as coarse and small fractions. The end product is a concentrate consisting either of the valuable mineral(s) and associated heavy minerals, which are taken to a treatment plant on shore; or in the case of gold, a clean amalgam ready for retorting. The bucket-line dredge may be adapted for purposes other than mining for valuable mineral by installing, in lieu of a concentrating system, machinery for pumping all of the solids ashore in a pulp, or for producing washed gravel in selected size fractions of which all or a selected fraction is pumped to disposal areas on shore or into side barges. The two principal types of bucket-line dredges designed for mining are: 1) those having an inclined belt conveyor stacker to discharge the coarse fraction of washed tailing well astern of the hull, and sluices to discharge the sand fraction (Fig. 8.5-1), and 2) those having only sluices for discharge of all tailing astern. Use of the latter type has been confined, with few exceptions, to mining cassiterite-bearing deposits in Malaysia and at sea off Indonesia. Small dredges having only flumes for washing and concentrating all material dug by the buckets have been used for mining shallow stream valley deposits. GENERAL ARRANGEMENT. The general arrangement of a modern bucket-line dredge for mining tin, with a primary concentrating plant on board, is shown in Fig. 8.5-2. The hull and superstructure of most dredges are fabricated of structural steel; wood also has been used for both small and large dredges with complete satisfaction. All-riveted or partially welded unit hulls have been widely used and are desirable for exceptionally severe service. The hull

Jan 1, 1968

By Enid C. Plante

THIS paper deals with the flotation of the mineral fluorite (calcium fluoride) and of two associated gangue minerals, calcite and quartz. The aim of the investigation was to produce "acid-grade" fluorite, which must contain less than one per cent of silica. Several reagents are used successfully in practice for floating fluorite from its ores. Oleic acid is the most widely used collector, usually at temperatures above 60°C, with sodium silicate as a dispersant for quartz and quebracho or tannin to depress calcite. Sulphides (e.g., galena) are often removed first by xanthate flotation. Many investigators23 report results in which more than 80 pct of the fluorite is recovered in a concentrate assaying 96 pct or more of fluorite and less than I pct of silica. This investigation was undertaken with the intention of floating the gangue, which is the minor constituent of the ore, from the fluorite. Hence emphasis was first placed on the cationic compounds that float quartz. No satisfactory separations were obtained in this way, and other reagents were investigated to discover whether these were more effective than oleic acid in floating fluorite from quartz in the usual way. The first part of the paper describes experiments with several long-chain collectors available commercially. Most of this work has been by captive-bubble and cylinder flotation tests, with some batch tests in a flotation machine. The second part describes the use of sodium cetyl sulphate as a collector for fluorite and includes laboratory tests and extension of the work to batch tests in the flotation machine. A method for determining the adsorption of sodium cetyl sulphate on fluorite has been developed and is described. Theory of Collection by Paraffin-chain Salts It may be assumed that these compounds are adsorbed at the mineral surface in one or more of three ways outlined by Kolthoff :12 I. Exchange adsorption between lattice ions in the mineral surface and collector ions in solution. Closely related is adsorption by the collecting mechanism postulated by Taggart,17 in which there is metathesis between the collector and the mineral cation or anion. 2. Exchange adsorption between adsorbed gegen ions (p. 67, ref. 19) and collector ions in solution. 3. Adsorption of nonelectrolytes (polarnonpolar) without displacement of adsorbed ions. With cationic collectors, inorganic cations in the solution (e.g., hydrogen ion) compete with the collector ions and therefore act as depressants, while inorganic anions have the same effect with anionic collectors. From this follows the general conclusion that ions of the same charge as

Jan 1, 1947