Search Documents

By Charles E. Parsons

One of the greatest factors in our industrial development is cheap and convenient power. Long-distance electrical transmission has now reached such a stage that it is feasible, and practicable, to utilize the water-power of the country which was heretofore too remote for consideration. In all of the changes of energy from its various sources to its electrical applications, water-power stands pre-eminent in point of economy. Power-users the world over have endeavored to utilize this force in preference to any other, and until long-distance transmission was found practicable it seemed that every available water-power in this section of the country was doing its full share for the benefit of mankind. The success of each great industrial development has been clue in a greater part to some one man one who is just a step in advance of the rest in his particular field; one who is able to grasp a situation and foresee possibilities; and, above all, one who has that indomitable pluck and perseverance which sees in each obstacle one more step toward success. Such a mail is Eugene L. Ashley, for it was through his efforts that the development of the greatest power on the Hudson river was made possible. For several years prior to 1897 the various properties along the river between Glens Falls and Palmer Falls were in the hands of speculators. These men knew the value of waterrights, but they had not the ability to assemble the properties and finance such an undertaking. In 1897 Mr. Ashley began buying these water-rights, and, after two years of litigation, title mas secured to all of the properties along each side of the river, and the Hudson River Water-Power Company was organized to construct a dam and transmit power to the surrounding cities and villages. A contract was let for a dam

Jan 1, 1904

By Roman Šejnoha, Karel Mazanec

A pronounced tendency for delayed fracture zoas observed in the martensite structure of low-alloy steels in the as-quenched condition. Cracks of predominantly intercrystalline nature nucleated and propagated at stresses substantially lower than the short-titne tensile strength of- the steels, and were observed even in hydrogen-free speciunens. The occurrence of delayed fractures in the as-quenched condition is interpreted as a supevposition of the effect of free dislocations generated during the martensite transforlnation, and of a weakening of the prior austenite grain boundaries caused by dynamic shocks exerted on the boundaries by growing martensite plates. AN important metallurgical problem, connected with the production and use of high-strength steels, is delayed fracture in martensitic structures. Such fractures occur in quenched steels as a result of prolonged loading with external stresses far lower than the short-time tensile strength of the steel. The same effect can be produced by sufficiently high internal stresses: it is well-known that quenched structures will in some cases crack intergranularly at room temperature if not tempered quickly enough even in the absence of any externally applied stress. In Troiano's papers1,2 on delayed fractures in high-strength steels, the fundamental role of hydrogen migrating under the influence of multiaxial stress towards the nuclei of cracks was found. Fig. 1 shows the typical relationship between stress and the time to fracture found by Troiano in hydrogen-charged high-strength steels. On the other hand, Shurakov 3,4 explains the realization of delayed fractures in martensite as due to a "quasi-viscous" behavior of the austenite grain boundaries immediately after the martensitic transformation. 1) MATERIALS AND EXPERIMENTAL METHODS Two low-alloy steels of commercial purity were used for the experiments reported in this paper. Their chemical composition is shown in Table I. The heats were melted in a laboratory furnace, cast to ingots, forged to bars of 3/4 in. diameter, and annealed. Machined test pieces were heat-treated as follows: Ni-Cr-Mo steel held at 900°C for 30 min and quenched in oil; Mn-Si-Cr steel held at 900°C for 30 min and quenched in water. For the delayed-fracture tests, notched cylindrical test pieces, Fig. 2, stressed in torsion, and unnotched cylindrical tensile-test pieces, 1/4 in. diameter, were used. The specimens were normally loaded with a constant static load 45 min after quenching for the torsional tests and 10 min

Jan 1, 1965

By A. A. Rauth

In this paper, the author derives a series of formulas from basic principles and illustrates the application of these formulas to practical grinding charge problems. The paper establishes the nearly proportional relationship of mill power to charge level and shows how this relationship can be used to advantage in the design, manufacture and operation of grinding mills. The procedures outlined offer a rapid means of anticipating the power requirements for a given charge or determining makeup charges for a given power reading. The theories which have been developed concerning the dynamics of grinding have been motivated largely by the desire to derive workable formulas for the accurate determination of grinding mill power. This accurate determination has always been handicapped by the large number of variables to be considered, some of which are mill diameter, length, speed, liner design, grinding charge and material density, volumetric mill loading, internal friction, and charge size and gradation. In efforts to determine mill power, attempts have been made to utilize torque concepts. The formulas derived consider the grinding mass as a rigid body and utilize factors that are based on empirical data so that the movement of the charge within the mill is compensated for. These formulas are of principal interest to the mill designer since he is charged with the responsibility of analyzing all of the variables and from them predicting a mill size and a motor size which are compatible both with each other and with the grinding job for which they were intended. The mill operator, on the other hand, has an entirely different problem. The mill dimensions are already established and so is the driving motor. The operator's main concern is to obtain maximum performance from the mill he already has. For him, the many variables which perplex the mill designer are fixed values. Mill diameter, length and speed are set and, to a large extent, so are the conditions inside the mill from which the torque formula advocates derive their empirical data. It is conceivable that if the major mill dimensions which affect power demand are held constant, and if the variables influencing empirical factors are held fairly constant, as they are in an operating mill, then the only major variable remaining which affects power is the level of the charge itself. Under this condition.

Jan 1, 1970

By Frederic L. Kadey

Diatomite is a siliceous, sedimentary rock consisting principally of the fossilized skeletal remains of the diatom, a unicellular aquatic plant related to the algae. Thus, it has-been formed by the induration of diatomaceous ooze, and consists mainly of diatomaceous silica, a form or variety of opal which is first formed in the cell walls of the living diatom. Diatomaceous silica is not generally regarded as a synonym or the equivalent for diatomite, although it has been so used at various times. Accurately, diatomaceous silica is the preferred name for the principal mineral component of which the rock, diatomite, is composed. The terms diatomaceous earth and kieselguhr are used as synonymous with diatomite. The designations tripoli, tripolite, infusorial earth, etc., were used at one time but are now obsolete. With the changing nomenclature, these terms that were at one time correct when proposed and used for generations would be considered incorrect if used today in the light of current knowledge. The designation diatomite is reserved for those accumulations of diatomaceous silica that are of sufficient quality, size, and minability to be considered of potential commercial value. Processed diatomite possesses an unusual particulate structure and chemical stability that lends itself to applications not filled by any other form of silica. Foremost among these applications is its use as a filter aid, which accounts for over half of its current consumption. Its unique diatom structure, low bulk density, high absorptive capacity, high surface area, and relatively low abrasion are attributes responsible for its utility as a functional filler and as an extender in paint, paper, rubber, and in plastics; and as an anti-caking agent; thermal insulating material; catalyst carrier; and chromatographic support; polish, abrasive, and pesticide extender to name a few representative applications. The United States is the principal producing country, although diatomite is found in numerous other locations.

Jan 1, 1975

By R. D. Pehlke, J. F. Elliott

The equilibrium pressure of nitrogen gas over pure silicon metal and silicon nitride has been measured in the temperature range 1400° to 1700°C. From the experimental data, the standard free energies and enthalpies of formation of Si3N4(a) have been calculated as functions of temperature over the above temperature range. Utilizing data in the literature and the results of this investigation, the specific heat, molar enthalpy, molar entropy, standard enthalpy of fornation, and standard free energy of fornation are estimated for the temperature range 298° to 1400°C. THE high-temperature thermodynamic properties of many metallic nitrides are not well established at present. This is a serious deficiency because nitrogen and nitride-forming metals are important alloying additions to steels, and knowledge of the interaction between nitrogen and these elements is essential to a better understanding of the behavior of steels. Metallic nitrides also are used as refractory materials. Consequently, the investigation reported here was undertaken to provide more complete information on the standard entropy and free energy of formation of silicon nitride. The experimental technique provided a direct measurement of the equilibrium pressure of nitrogen gas in the range of 1413 to 1700°C for the reaction: 3 Si(1) + 2N2 (g) = Si3N4 (a) [ 1 ] and below 1413oC for the reaction: 3Si(c) + 2N2(g) = Si3N4(a) [2] APPARATUS The experimental system consisted of a crucible assembly, a reaction chamber, and a gas supply and vacuum system. The Crucible Assembly which contained the equilibration specimen and molybdenum radiation shields with a susceptor for induction heating is shown in Fig. 1. Two covered, high-purity alumina crucibles, one nested within the other, contained the susceptor, shields and specimen. Central openings in the upper shield and crucible covers permitted on optical pyrometer to be sighted into the central cavity of the specimen. The specimen itself was a 5/8 OD by 1-in.

Jan 1, 1960

By G. W. Cullen

Niobium-tin has been prepared on insulating suhstrates hby simultaneous hydrogen reduction of gaseous niobium and tin halides. Stoichiometric material is greater than 98.8pct theoretical density, appears to he single-phase, and has a total impirity level less than 0.3 at. pct. Transition temperatures and lattice constants may he related to composition. Typical current densities in various fields and orientations are given. IT is known that Nb3Sn carries large current densities in high fields, 1 and exhibits an unusually high transition temperature2 and critical field.3 For these reasons high-field solenoids have been constructed of this material.4 Because of the emphasis on solenoid fabrication, much of the materials research has been directed toward development of wire geometries wherein the brittle Nb3Sn is supported by a more malleable metal or alloy. There are, however, basic studies and applications that can be carried out only on Nb3Sn supported by an insulator. Insulating substrates are desirable for a number of reasons: the substrate does not interact with applied or induced currents and fields; diffusion of metallic species into the de- posit is avoided, both during the preparation and during subsequent heat treatment; irradiated samples are not more active than the deposit itself. Unsupported Nb3Sn geometries may also be prepared by preferential chemical dissolution of the insulating substrate. This report describes the preparation and properties of Nb3Sn deposits on ceramic substrates. Experiments currently utilizing material prepared in the manner described in this report include the following: dependence of current-carrying properties on field strength and orientation 5,6 radiation damage,7,8 tunneling,9 thermal conductivity (substrate removed),1° microwave surface impedance," tube magnetization,6,12 resistivity as a function of temperature,13 and current density and transition temperature as a function of annealing.14 Possible practical applications include magnetic shielding, superconductor generators, and frictionless bearings. PREPARATION Methods for the deposition of elemental niobium and tin by hydrogen reduction of the gaseous metal halides have been known for some time,15,18 but only recently a procedure was developed in this laboratory17 for the codeposition of these two metals on a hotwire as the intermetallic compound, Nb3Sn. This method of simultaneous hydrogen reduction of the gaseous niobium and tin chlorides is used for the preparation of Nb3Sn On ceramic substrates. The procedure differs from that employed on a hot wire in that insulating substrates cannot conveniently be heated to temperatures greater than their surround-

Jan 1, 1964

By Clarence Merritt

STAINLESS iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mysterious electrolytic effects or comparatively minute non-metallic inclusions. Many uses for a steel with such excellent physical properties is are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that' the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties, 1,2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties-hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion.3 Monypenny reports that a loss of hardness is

Jan 1, 1932

By B. A. Cheadle, K. P. Steward

Axial tensile, ring tensile, closed end burst, and free end burst tests were done at room tempe.vature and 300°C on three batches of Zircaloy-2 sheathing zuith different textures. Knoop hardness tests were also done on all batches. The mechanical properties of the tubes were largely dependent on the percentages of cold work, but were also markedly affected by the textures, particularly with respect to deformation behavio'r. The deformation behavior observed confirmed Picklesimer's predictions, zuhereas Knoop hardness results could be correlated with texture and yield strength anisotropy after the ,method of Wheeler and Ireland. From the mechanical properties, and from efjectiue strain values deterrlzined at the fractures using a photoqid technique, it zuas concluded that tubing witlz a single preferred orientation of radial basal poles best combines strength and ductility for any given deqee of cold work. THE mechanical properties required in collapsible Zircaloy-2 fuel sheathing for water-cooled power reactors are strength to resist wrinkling deformation by coolant pressure and ductility to accommodate a small amount of deformation in service without rupturing. Zircaloy-2 tubing during fabrication develops pre- ferred orientations of the a Zr grains due to aniso-tropic deformation behavior, and these textures markedly affect mechanical properties. Picklesimer' had predicted the deformation behavior of tubes with various textures, but the texture required to provide the optimum strength and ductility for a given degree of cold work has not been reported. To investigate this problem, tests at three transverse to axial stress ratios were done at room temperature and 300°C on three batches of Zircaloy-2 tubing covering a wide range of textures and percentages of residual cold work. Knoop hardness values were also measured to correlate with preferred orientation and yield strength anisotropy after the method of Wheeler and relland.' 1) MATERIAL For this investigation, three batches of tube-reduced tubing were chosen from the Zircaloy-2 sheathing produced for the Douglas Point Reactor. Individual tubes were 191/2 in. long, 0.600 in. OD, and 0.0165 in. nominal wall thickness. The identities of the batches, together with their textures, are shown in Table I. The tubes had the normal Zircaloy-2 composition3 of 1.5 wt pct Sn, 0.3 wt pct Fe, Ni, Cr combined with the following oxygen concentrations: Batch VII 1140 to 1390 ppm 0 Batch VIII 1400 to 1750 ppm 0 Batch IX 880 to 1320 ppm 0

Jan 1, 1968

By E. M. Tory, P. T. Shannon

An analysis of batch and continuous thickening in terms of the movement of planes of constant concentration (i.e. continuity waves) is presented. Use of solids flux as a primary variable greatly facilitates the analysis and clarifies the relationship between batch and continuous thickening. An "ideal" slurry is defined as one whose settling rate is a function only of the local solids concentration. An analysis of continuous thickening of this ideal slurry in an ideal thickener explains many aspects of the steady — and unsteady — state behavior of real slurries, such as the main features of a thickener's "solids profile" (including the break attributed to rake action), the sudden appearance at abnormally high feed rates of a zone of constant concentration and the velocity with which it rises, and the effect of detention time at constant weight of sludge per unit area. Where deviations exist, they are explained in terms of the batch settling behavior of real slurries. The purpose of this paper is to interpret continuous thickening phenomena in terms of batch settling behavior. Both types of thickening may be considered as the process of propagating concentration changes, due to the downward movement of the solids, from the bottom of the settling vessel upward through the slurry.' These concentration changes may be either finite or infinitesimal as in the case of the propagation of a continuous concentration gradient. The slurry itself may be moving downward as in the case of continuous thickening. The downward velocity of the slurry may be such that the concentration changes being propagated up from below remain stationary relative to the thickener walls. This is the case for steady-state thickening. It seems appropriate to analyze continuous thickening in terms of the movement of planes of constant concentration. This has already been done for batch settling."3 Although our main interest is in real slurries, there are certain aspects of both types of settling which can be deduced from a theoretical analysis of highly idealized systems. To this end, an "ideal slurry" is defined as one for which the dimensionless settling rate at any point is a function only of the local solids concentration.1,2 An "ideal thickener" is one in which there is no radial variation in either the solids concentration or in the downward component of slurry velocity. The underflow outlet is a point sink. It is to be expected that the behavior of non-ideal systems will deviate in some measure from theoretical results. However, the same characteristics which cause deviations in continuous thickening should be evident in batch settling, permitting a rational explanation of the former in terms of the latter. PREDICTED RESULTS FOR AN IDEAL SLURRY IN AN IDEAL CONTINUOUS THICKENER General Theory: In continuous thickening, the downward solids flux (mass/area-time) relative to the thickener, G, results from two different

Jan 1, 1967

By H. E. Cline

Mechanical properties of the eutectic between CoAl and cobalt were measured over a range of- temnperatures and strain rates for a variety of microstructures produced by directional solidification and by thermo-mechanical processing. Directional solidification led to rodlike, lamellar, and irregular microstructures. The unusually high volume fraction of the cobalt-rich rods and the lurge spacing of the rods were explained by the phase diagram. The hot-worked structure consisted of fibers of COAL in a cobalt-rich matrix. The roonl- tevlperature strength of the uvrought material increased with decreasing grain size but the 1000°C strength decreased with decreasing pain size. At high temperatures the directionally solidified tnaterial was stronger and less strain-rate-sensitice than the hot-rolled material. The fine-grained hot-worked ma-terial became superplastic at high temperatures, with tensile elongations greater than 850 pct, while at root temperature this material was ductile and impact-resistant because of the ductile matrix. Fracture occurred in the directionally solidified material at elevated temperatures by inter phase separation and at roorn temperature by cracks in the intermetallic phase. Growth of these cracks was impeded by the ductile cobalt-rich phase. It was found that the CoAl intermetallic remains ordered at elevated temperatures. DIRECTIONAL solidification of eutectic alloys has been used to produce structures consisting of parallel rods or lamellae. Although the spacing of the phases depends on the growth rate, it has been observed to be of the order of 1 µ in many eutectics. A strong intermetallic phase has been used to reinforce a ductile matrix in the rod eutectic A1-Al3Ni and the lamellar eutectic Al-Al2cu.1 The microstructure of the eutectics A1-A13Ni and A1-A12Cu remained aligned after samples of these alloys were exposed to temperatures just below their melting points for long times. Stability of the microstructure at elevated temperatures makes directionally solidified eutectics a candidate for high-temperature applications. Recently Thompson4 has developed the Ni-NiMo eutectic containing 40 pct NiMo lamellae, giving a tensile strength superior to nickel-base superalloys. Unfortunately, this eutectic oxidizes rapidly at elevated temperatures. By mechanically processing a two-phase structure, one may reach strengths as high as 700,000 psi, as demonstrated by drawn pearlite.5 In this case the strengthening mechanism was thought to be related to the fine substructure formed during deformation.5 However, a heavily worked structure may recrystallize and coarsen at elevated temperatures. Some worked eutectics such as Al-Al2Cu,6 Pb-Sn,7 and Sn-Bi7 have shown unusually large elongations in tension when tested at elevated temperatures. This phenomenon of large extension, called "superplasticity", was related to the fine grain size of wrought two-phase alloys at elevated temperatures. A mode of deformation of "superplastic" material has been shown to be grain boundary sliding,' which has also been observed during creep of polycrystalline materials.9 The Co-A1 system was chosen for this investigation after examining the phase diagrams of binary eutectics." The high melting point of 1400°C, the aluminum content which was expected to give oxidation resistance, and the properties of the intermetallic CoAl were the chief factors influencing this choice. This eutectic consists of a mixture of the intermetallic CoAl and a cobalt-rich solid solution. The intermetallic CoAl has a large range of solubility and a CsCl structure." From the similarity between CoAl and NiAl one would expect CoAl to be ordered at elevated temperatures; however, specific heat measurements" show a transition at 800°C. West-brookL2 has measured the hot hardness of CoAl and found a rapid decrease in hardness above 600°C. The tensile properties and stress rupture properties of as-cast CoAl-Co eutectic were measured by Ashbrook and wallace13 who report a room-temperature tensile elongation of less than 1 pct. I) EXPERIMENTAL A) Sample Preparation. Experimental materials were prepared by directional solidification, by hot working, and by powder processing. The starting materials were electrolytic 99.9 pct pure cobalt and 99.99 pct pure aluminum. 1) Directional Solidification. A vertical Bridgman apparatus heated by induction was used to directionally solidify cylindrical ingots $ in. in diam and 5 in. long. The apparatus was first evacuated and then an argon atmosphere was introduced to retard evaporation. The ingots were contained in an alumina crucible inside a graphite susceptor that rested on a movable water-cooled base. The base was lowered out of the induction coil at a constant rate. Eight of the ingots were solidified using a drive rate of 2.5 cm per hr, two of the ingots at 1.2 cm per hr, and one ingot at 10 cm per hr. The eutectic composition Co 10 wt pct A1 was used in all but one ingot which had the composition of the stoichiometric CoAl intermetallic, Co 32 wt pct Al. 2) Mechanical Processing. At 1000°C the eutectic Co 10 wt pct A1 is a mixture of an intermetallic phase, Co 21 wt pct Al, and a cobalt-rich phase, Co 5 wt pct Al.10 These phases differ from the stoichiometric CO 32 wt pct A1 and pure cobalt because of the large solubility of this eutectic at elevated temperatures." Four rectangular slab ingots, 4 by 1 by 12 in. high, of Co 10 wt pct Al, Co 5 wt pct Al, Co 21 wt pct Al, and Co 32 wt pct A1 were cast for hot rolling. The cobalt was first vacuum-melted, H2-treated for 20 min,

Jan 1, 1968

By Joseph W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of minus %-inch coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing saleable coal to the fine coal cleaning section of the preparation plant. Because a given weight of fine coal will contain substantially greater surface area than an equivalent weight of coarse coal, it follows that, when subjected to wet cleaning processes, the fines will absorb and retain consider- ably more moisture than coarser fractions. Increased moisture pickup in the finer sizes complicates fine coal cleaning since beneficiation may not be limited to the removal of ash and sulfur but often must be expanded to include the additional step of thermal drying to remove excessive moisture. Thus, water which provides the medium for cleaning fine coal is in itself detrimental and, like ash and sulfur, reduces coal quality. Removal of surface moisture by drying is done for one or more of the following 1 reasons: (1) To avoid freezing difficulties and to facilitate handling during shipment, storage and transfer to the points of use; (2) to maintain high pulverizer capacity; (3) to reduce heat loss due to evaporation of surface moisture from the coal in the burning process, thus increasing heating efficiency; (4) to improve the quality of coal used for special purposes, such as in the production of coke, briquettes, and chemicals; (5) to decrease transportation costs; and (6) to facilitate dry coal-cleaning processes. Because benefits to coal transportation and utilization are the most common reasons for thermal drying, the following sections will examine these areas in greater detail. Benefits to Transportation Initial benefits from drying are the reduction of shipping costs from the mine to the point of utilization since more coal can be concentrated into a given weight of product when worthless moisture is removed. Non- combustible~ such as water and mineral matter in railroad shipments of coal are billed the same as coal at $3.32 per ton, according to the recent average costs. Savings of 10 to 20 dollars from drying on the shipment cost of each 50 to 60 tons of coal contained in a typical railroad car is common. Savings on coal shipments from individual mines which result from coal drying can be expressed in terms of hundreds of thousands of dollars and more each year. For example, a reduction of shipping charges of only 5 percent on one million tons per year would mean a savings of 166,000

Jan 1, 1968

By T. V. Philip, R. E. Lenhart

When commercial silicon iron sheets of varying magnetic quality are isothermally annealed at high temperatures, extremely large grains develop in the material having good magnetic properties. These grains are of the (110) [001] orientation and are formed by secondary recrystallization. The primary driving force for this secondary recrystallization is grain boundary free energy. For the secondary grains, activation energies of 103 kcal per mole for nucleation, and of 75.5 kcal per mole for growth, were obtained. The activation energy for nucleation of the secondary grains is consistent with a model involving redistribution of a precipitate acting as the primary grain growth inhibitor. SINGLY oriented silicon iron sheet was first produced in 1935.1 The material as commercially produced today has a very highly developed preferred orientation or texture; up to 95 pct of the grains are crystallographically oriented with their (110) planes in the plane of the sheet and their [loo] directions parallel to the rolling direction. This texture, usually written as (110) [00l], is referred to as the "GOSS" or the "cube-on-edge" texture. Because the magnetic properties of this material are superior to those of the nonoriented sheets in the direction of rolling, the oriented silicon iron has acquired tremendous industrial importance especially in the manufacture of transformer cores and other electrical equipment. The commercially produced material is essentially an iron-silicon alloy containing about 3 1/4 pct Si with minor impurities totaling less than 0.15 pct. The silicon steel heat is melted in the open hearth or electric furnace. The ingots are hot rolled, with or without being slabbed, to strips of 0.100 to 0.080 in. thickness. They are then cold reduced to an intermediate thickness, recrystallized, cold reduced to final thickness, decarburized, and finally annealed at a high temperature. During this high-temperature anneal, extremely large grains with the cube-on-edge texture are produced in the sheet. Several papers have appeared in the literature2-10 relating to the production of the Goss-textured material. Most of these describe the textures produced on cold rolling and on subsequent annealing of single crystal or polycrystalline silicon iron. May and Turnbull11,12 have recently shown the necessity of a second-phase dispersed impurity in the material for the production of the Goss texture. However, none of these papers describes in detail the nucleation and growth kinetics of the (110) [001] grains during the final high-temperature anneal.* The present work, therefore, is an attempt to understand the nucleation and growth kinetics of the cube-on-edge grains in the silicon iron sheet during the final high-temperature anneal.

Jan 1, 1962

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies' of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed, to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1947

By Charles G. Maier

It has long been supposed that when crystalline materials are comminuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1.t The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chemical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the corrected heat of solution was less for fine material than for coarse. Continuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. Similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by Rosenhain and Stott4 and by Taylor and Quinney9 The results obtained by the different investigators were not satisfactorily consistent, but the experiments of Taylor and Quinney constitute by far the best figures obtained to date. The previous paper1 presented evidence to show that if energy is stored in the surfaces of crystals the densities of fine crystals should differ

Jan 1, 1936

By Arthur B. Cummins

Mineral fillers are employed in United States industries to the extent of more than seven million tons annually, valued in excess of a hundred million dollars. This substantial usage involves a wide variety of mineral materials. To this may be added products manufactured from minerals, such as carbon black, portland cement, lime or chemically precipitated calcium carbonates, which would add substantially to the total. The purposes for which fillers are used differ considerably. Minerals used as fillers are mostly silicates, silicas, and carbonates as referred to hereinafter. The term "mineral filler" has various meanings in mineral technology and in the arts. Fillers are comparatively inert and their action is mainly physical. Materials that are employed primarily for chemical reactivity, or for pigment or abrasive functions ordinarily would not be considered to be fillers when used for these purposes. Nearly all filler usages are based on advantages which are gained by desired modification of composition properties or by improvements in processing. A simple definition for a filler is an inert material that is included in a composition for some useful purpose. This definition may be amplified or made more specific for each of the filler usages, the major ones of which are: paints, paper, plastics, rubber, bituminous compositions, pesticides and fertilizers. There are in addition a whole host of minor usages. Powdered minerals when employed as components in paints, varnishes and lacquers are considered as extender pigments or low refractive index pigments. In paper, the term loading material as well as filler is used; in pesticides, the terms diluents and carriers connote different functions. For bituminous compositions, rubber and plastics, the usage of the simple word "filler" is more usual, but the designation loading material is sometimes used. Minerals Used as Fillers Most of the industrial minerals, and many rock powders are employed to some extent for different filler uses. These usages vary from year to year depending on availabilities, costs, technologic trends and advancements. For the major applications, however, and for the more particular requirements at any given period, there are general trends which favor a more or less restricted group of filler products for each of the major consumer fields. This selection of materials is determined by the characteristics of the individual filler products, their effectiveness in fulfilling the primary function or functions for which they may be employed, and the cost after incorporation in the finished product. The mineral-bearing materials of major importance as fillers are: limestones, clays of several types, talc, pyrophyllite, mica, barite, diatomite, crystalline silicas, asbestos, slate and other rock dusts. Others of secondary importance include: gypsum, vermiculite, phosphate rock, perlite, and pulverized wastes, such as slag and fly ash. A considerable number of other minerals are used to lesser extent. Among these minor mineral materials are: feldspar, pumicite, wollastonite,18 tripoli, nepheline syenite,6 coal, altered volcanic rock and others.2 Indeed, most mineral materials, when reduced to fine particle size may have some potential usage as fillers, depending on their properties, availability and price. On the other hand, the more exacting filler requirements

Jan 1, 1960

By John M. Dealy, Robert D. Pehlke

Values for interaction parameters in nonferrous systems, as calculated from published data, are tabulated and discussed. The influence of temperature on the parameter is derived and compared with the results of the literature study. Wagner's relationship between the interaction parameter and the self interaction coefficients is compared with the tabulated data. A problem which has been of considerable interest in the field of metallurgy is the prediction of the effect of one alloying element present in dilute concentration on the thermodynamic properties of another dilute alloying element. Ultimately, the prediction may be accomplished entirely from statistical mechanical considerations. At the present, however, the problem remains unsolved since liquid solution models which are simple enough for analytical treatment are inadequate for such purposes. Thus, we desire some means of organizing the information on dilute systems which will serve as a guide for further study on interactions in dilute alloys, and also provide a basis for the utilization of thermodynamic data in the engineering design of alloys.

Jan 1, 1963

By Henry Rawdon

ANY laboratory corrosion test, as judged from the practical point of view, is valuable only to the extent that it foretells what will, in all probability, occur in service. Such a test is most properly to be considered as a "pilot test, " that is, a test which indicates the direction along which action may be expected to occur rather than as a truly quantitative test which would be expected to tell just how and to what extent the action would proceed. It is generally recognized that laboratory corrosion tests should be chosen with particular reference to the character of service expected for any particular type of metal, so far as it can be foreseen. Even when this requirement has been fulfilled, however, the question whether the actual service behavior of the material is in accordance and general agreement with predictions based upon such laboratory tests is always a pertinent one. The information available in the technical literature bearing on the correlation between the service behavior of metals from the corrosion standpoint, and the results obtained with the same metals in laboratory corrosion tests is very meager, indeed. The results which have been obtained in weather-exposure tests of sheet duralumin which form the body of this discussion are presented here for their bearing on this particular phase of the problem of the corrosion resistance of duralumin. Although the exposure tests described have not been completed, in the sense that all of the tests, in the series initially laid down, have been accomplished, still the general trend shown by the results is so clear that a number of definite conclusions at this stage (subject, of course, to possible modification in the light of later results) are believed to be warranted. The tests reported upon here form one phase of the much broader study of this subject which has been under way for several years in which the National Advisory Committee for Aeronautics, the Bureau of Aeronautics of the Navy Department, the Army Air Corps and the Bureau of Standards have cooperated. Without the very helpful cooperation of the manufacturers in furnishing the

Jan 1, 1929

By L. C. Graton

THE Federal taxes on incomes and excess profits are of course heavy. In 1917, the value of the mineral production of the United States was a little in excess of $5,000,000,000. The total of Federal taxes for that year, for the mineral producing companies, as computed by themselves, amounts, according to tentative compilations, to about $207,000,000, and the total for the comprehensive group of mineral and metal indus-tries to about $766,000,000, which figures represent respectively 9.5 per cent. and 35.1 per cent. of the total tax paid by all corporations. Be-cause of greater complexities in applying the revenue laws to mineral properties than to most other industries, opportunity is afforded for wide differences of view. The taxes indicated above, therefore, are not final

Jan 11, 1919

By L. R. Duncan, O. M. Wicken

Magnesium, the eighth most abundant element in the earth's crust, is found widely distributed in a variety of minerals. Among the more commercially important ones are magnesite (MgCO3), brucite (Mg[OH]2), dolomite (CaMg[C03]2), and the salts magnesium sulfate and chloride often found in natural brines. Among other commercially important magnesium-containing minerals are olivine ([MgFe]2Si04), talc (H2Mg3[Si03]4), and serpentine (H4Mg3Si2O9). These are valuable because of desirable characteristics given them by the magnesium content and its placement in the particular crystal structure. These minerals are the raw materials for a host of products including magnesium metal and several grades of magnesia or magnesia-containing materials for refractories, fluxes, fillers, insulation, cements, decolorants, fertilizers, and chemicals. Considering only those minerals valued for their magnesia or magnesium content, over 85% of the material tonnages are processed to be used as refractories. Dolomite, which is used in enormous tonnages for its physical properties in construction, has an important use as a refractory raw material in its own right and, after calcination, as a precipitant for magnesium hydroxide, which is an intermediate for the production of magnesia or magnesium metal. Magnesia from the reaction of calcined dolomite (or limestone) with seawater or magnesium-containing brines has supplanted much of the production of magnesia from mined magnesite, particularly in the United States. The best known of the minerals directly and widely exploited for magnesia content is magnesite, one of the calcite group of rhombohedral carbonates which includes calcite (CaC03), siderite (FeCO3), and rhodochrosite (MnCO3) among others. The members of this group enter into a wide range of substitutional solid solutions when the positive ions have similar radii. The radii of magnesium and iron ions are within 6% of each other; hence, magnesite and siderite form a complete series of which breunnerite (ferroan magnesite) is a well-known end member. However, the radius of calcium ion is 36% larger than that of magnesium ion, and only limited substitution exists at each end of the MgCO3-CaCO3 series. Dolomite is not a member of the calcite group, but results when calcium and magnesium ions alternate in equal number in an ordered structure among carbonate ions. The result of these relationships is that calcite and dolomite, often found intermixed with magnesite, occur commonly as identifiable crystal entities which can often be separated to a varying degree from the magnesite by various beneficiation techniques. Magnesite, when pure, contains 47.8% MgO and 52.2% CO.. The pure mineral is sometimes, but rarely, found as transparent crystals resembling calcite, but, preponderantly, magnesite contains variable amounts of the carbonates, oxides, and silicates of iron, calcium, manganese, and aluminum. Magnesite may be either crystalline or amorphous (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black with shades of yellow, blue, red, or gray. The color is not a fundamentally significant indicator of purity, but in a given deposit, an experienced person can often roughly grade magnesite by assessing color and crystallinity. The crystalline form of magnesite occurs in

Jan 1, 1983

By J. M. McDowell, E. C. Doty, F. Morgan

Improvements in the X-ray method of measuring liquid saturation and saturation distribution are presented. Two identical direct current amplifiers have been added to measure continuously the intensities of the X-ray tube output and the beam which has passed through the core under test. The ratio of these intensities is automatically recorded on a modified Brown Electronik Recorder. Arrangements have been made to drive the core automatically and in synchronism with the recorder chart so as to give a continuous curve showing the variation of liquid saturation along the length of the core. By determining the ratio of the two X-ray beam intensities simultaneously the measurements are made essentially independent of small fluctuation in voltage and current supplied to the tube. This improved technique has been used for investigating the fluid distribution along the length of cores and core assemblies when one fluid is displaced by another. Typical results of these studies are shown. INTRODUCTION In a previous publication' a method was described for measuring the oil saturation in cores which was based on the absorption of X-rays by the fluid content of the core. While that technique is capable of yielding accurate results, the original apparatus was not especially convenient for determining the fluid distribution along the length of a core. This was primarily due to the slow response of the amplifier and galvanometer and the necessity of making a point by point survey of the material under investigation. It was, therefore, not only possible for sections of the core having a variable or unusual saturation distribution to escape observation entirely, but changes in output of the X-ray generator between readings on the unknown and the monitor introduced errors in the measurements that could be avoided only by further stabilization of the source or by taking a large number of readings. This paper describes a method and apparatus for recording continuously and automatically the intensity of the X-ray beam that is transmitted by a core. The variation of saturation with time at a given section of the core may thus be found, or by scanning the core by driving it in synchronism with the recorder the saturation distribution may readily be determined. As indicated in the previous paper, the X-ray method possesses an advantage over the weighing technique in relative permeability experimentation in that the core need not be removed from the holder for the purpose of making a saturation measurement. Furthermore, the actual distribution of fluid and the effects upon that distribution of inflow and outflow heads may be investigated. And errors due to gas bubbles or loss of liquid that are frequently sources of error in volumetric methods of saturation determination are avoided. PRINCIPLE OF THE METHOD The energy in an X-ray beam that has passed through an absorbing material is expressed by the well known formula: E = E0, e-cd (1) where E, is the energy in the incident beam, µ the mass absorption coefficient, c the density or concentration of absorbing material, and d is the length of path of the beam in the absorber. The coefficient µ varies with the wavelength of the radiation as well as with the absorbing material. The output of an X-ray tube varies in an approximately linear manner with the tube current, but to the second or higher power of the anode voltage. Moreover, the quality or wavelength distribution of the radiation varies with the voltage.

Jan 1, 1950