Search Documents

By J. F. Myers, S. E. Sharp

THE safety data presented in this paper are based upon replies to a Questionnaire sent out to representative mining companies. The authors feel that it is a fair cross section of the milling industry, in that the 17 companies, of the United States and Canada, reporting on 22 mills, are scattered from the Hudson Bay to the Mexican border and from coast to coast. These data concern the accident records of the. various plants from 1939 to 1944, inclusive and the six years are divided into two periods. The first period (1939, 1940 and 1941) represents something of a normal operating condition. The second period (1942, 1943 and 1944) represents the period of time that was most affected by war con¬ditions. During the second period there was a high labor turnover, inexperienced workers were numerous, women replaced men in many kinds of work, a labor shortage existed more or less throughout the industry, and supervision was pushed for peak production. All of the companies reporting compiled their accident experiences for these six years in accordance with the standards set up by the American Standards Association (Engineering Societies Building, New York, N. Y.), consequently the tabulated data presented herein are comparable. The authors of this paper feel that the industry as a whole is greatly indebted to the personnel of the companies that furnished these data, which make this study possible for presentation. This survey covers a total exposure of 74,528,880 man-hours, with 105,471 man-days of lost time from 870 accidents. SAFETY RECORDS In Table I, the safety record is shown of the various mills reporting. The severity rate is usually conceded to be the most vital statistical figure in safety parlance, therefore the participating companies are listed in order of their severity rate for the combined six-year period, under size of organization. The table also shows the frequency rate as well as the frequency-severity ratio (F/S). As noted in Table 1, most of the companies suffered an increase in both severity and frequency rates during the second period; only six of the 22 enjoyed an improvement. From correspondence with the various plants, it seems that a few had very little labor shortage or turnover, and these were not greatly affected. A few plants, anticipating the situation, strengthened their training facilities and actually were able to show a better experience during the second period. This gives great credence to the value of organized training in any safety program. The frequency-severity ratio (F/S) shown in the last column of Table I offers

Jan 1, 1946

As described in the section on the Palabora twin crushers, the Palabora ore consists of two types: a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. As the Palabora pit was widened and deepened, more and more of the foskorite had to be mined. The 25,000 mt expansion of the Palabora plant which went into operation in early 1977 therefore takes its feed from the foskorite section of the orebody. For the expansion, a third 54 in. by 74 in. gyratory crusher was installed to crush feed for two 32 ft by 15 ft (9.75 by 4.6 m), 9000 hp (6710 kw) autogenous single -stage grinding mills. These units are located near the two existing primary crushers, and the ground ore is pumped 5277 ft (1640 m) to the expanded flotation plant by five stages of centrifugal pumps. The new gyratory is installed in a unique Figure-8 shaped enclosure with the crusher in the smaller 27 ft 11 in. (8. 5 m) diameter cylinder and the maintenance area in the 36 ft 1 in. (11 m) diameter cylinder. Cylinder walls are only 23.6 in. (600 mm) thick because their circular design permits all the concrete to be in compression. A rectangular dump pocket which sits on the smaller cylinder contains two manganese steel faced splitters to protect the crusher spider and countersunk water spray headers under the dumping positions for dust suppression. The dump pocket holds 330 st or 300 mt and is also lined with manganese steel. The crusher is mounted on a reinforced concrete diaphragm over the 363 st (400 mt) crushed ore pocket. In the back of the pocket is plastic pipe. Radioactive level control sources are lowered into this pipe from the crusher support floor. The pipe is protected by concrete covered with steel castings. Level control detectors are mounted on the front wall of the pocket. Liner plates on the crushed ore pocket walls are removed and in- stalled by the use of a circular monorail and trolley mounted on the pocket ceiling. The door in the front of the crushed ore pocket is hinged at the top rather than at the sides and is raised by an electric winch. For removal of the eccentric, rails are installed in the pocket and a unique hydraulically operated cart is moved under the eccentric. A platform is raised to receive the eccentric and lowered so that it may be removed. Crushed ore is removed from the pocket by a hydraulically powered, 8 ft

Jan 1, 1978

By R. J. Miller, W. A. Bates

ALTHOUGH cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowy1 in 1930, which presented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids ; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. CONSTITUTION AND PROPERTIES Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen

Jan 1, 1946

By R. J. Miller, W. A. Bates

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947

By H. H. Uhlig

In our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotterl measured the electrochenlical potentials of alloys of iron-molybdenum and iron-chromium and reperted the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measurements for the iron-chromium system. The electrochemical potential3 has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1940

By H. H. Uhlig

In our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotterl measured the electrochenlical potentials of alloys of iron-molybdenum and iron-chromium and reperted the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measurements for the iron-chromium system. The electrochemical potential3 has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1940

R. H. THURSTON, Cornell University, Ithaca, N. Y. (communication to the Secretary): The " tri-axial diagram" was, I think, first employed by me in the work of the " U. 8. Board Appointed to Test Iron, Steel and Other Metals." A model was exhibited to the American Association for the Advancement of Science, and the diagram was first published, and the model described, in a paper presented to the same society at its Nashville meeting in 1877." The problem then presented to its inventor was to find a method of planning a research involving proportions of ternary compositions in such manner that, a limited number of such compositions being tested, the results should give the law of variation in the physical properties of all possible combinations of the three elements, and the actual numerical values of such as were important to the investigator. The investigation of the binary alloys, copper and tin, copper and zinc, and tin and zinc, had been completed and satisfactorily discussed, employing the usual bi-axial diagram, of which the ordinates represented the one, and the abscissæ the other, of the characteristic properties to be studied, the composition being commonly indicated by the abscissæ. In these cases it was easy to ascertain, by the study of a limited number of compounds, the law of variation in strength, ductility, etc., with composition; but, for a long time, the ternary alloys were not attacked, because no simple and satisfactory method presented itself of securing results significant for the whole field by the investigation of a comparatively small number of alloys. The tri-axial diagram was finally hit upon as a means of representing and interpreting results, and researches were at once begun, and in due time satisfactorily completed.

Jan 1, 1899

By L. Messulam, A. S. Appleton

Iwo major studies of the Fe-Cr-C system are available in the literature. The earlier one of Kinzel and crafts' forms the basis for the data most commonly quoted in works of reference (e.g., Metnls HandDook) though the later work of Bungardt el a1.' is more extensive and amenable to analysis in terms of isothermal sections and so forth. However it is evident from examination of either of these studies that the delination of phase boundaries on the basis of the data obtained can only be very approximate. Indeed in several instances the data are so inconclusive that this delineation is a matter of opinion. This note is to report an analysis of experimentally determined carbon activity data in this system, which, originally intended as a means of checking the self-consistency of the data for a number of alloys, enables some conclusions to be drawn concerning the 10503C isothermal section of the iron-rich corner of the system as deducible from the data of Bungardt

Jan 1, 1967

By Arthur Knapp

Oil-well depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. Data fob Lease Status-time or Dollars-timb Curve Time Lease Months Status Lease purchased for $3000.............................. 0 — $ 3,000 No expenses chargeable to lease for 3 mo................. 2 — 3,000 Well A is started; cost of drilling for month is $16,000..... 3 — 19,000 Well is completed at additional cost of $10,000............ 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (we Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.; difference between expenditures and receipts gives profit for month of $5,000............................ 5 — 24,000 Investment is small, cost of operating well A is small, so profits are $15,000................................... 6 — 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000. 7 ... Lease operation nor becomes normal and curve becomes smooth........................................... 8 — 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000 A hypothetical lease status-time, or dollars-time, curve of this lease is shown in Fig. 2. At zero time, the lease is purchased for $3000, which is plotted below the zero dollar line, All subsequent entries are plotted

Jan 1, 1921

By J. F. Myers, S. E. Sharp

The safety data presented in this paper are based upon replies to a Questionnaire sent out to representative mining companics. The authors feel that it is a fair cross section of the milling industry, in that the 17 companies, of the United States and Canada, reporting on 22 mills, are scattered from the Hudson Bay to the Mexican border and from coast to coast. These data concern the accident records of the various plants from 1939 to 1944, inclusive and the six years are divided into two periods. The first period (1939, 1940 and 1941) represents something of a normal operating condition. The second period (1942, 1943 and 1944) represents the period of time that was most affected by war conditions. During the second period there was a high labor turnover, inexperienced workers were numerous, women replaced men in many kinds of work, a labor shortage existed more or less throughout the industry, and supervision was pushed for peak production. All of the companies reporting compiled their accident experiences for these six years in accordance with the standards set up by the American Standards Association (New York, N. Y.), consequently the tabu lated data presented herein are comparable. The authors of this paper feel that the industry as a whole is greatly indebted to the personnel of the companies that furnished these data, which make this study possible for presentation. This survey covers a total exposure of 74,528,880 man-hours, with 105,471 man-days of lost time from 870 accidents. Safety Records In Table I, the safety record is shown of the various mills reporting. The severity rate is usually conceded to be the most vital statistical figure in safety parlance, therefore the participating companies are listed in order of their severity rate for the combined six-year period, under size of organizatiori. The table also shows the frequency rate as well as the frequency-severity ratio (F/S). As noted in Table I, most of the companies suffered an increase in both severity and frequency rates during the second period; only six of the 22 enjoyed an improvement. From correspondence with the various plants, it seems that a few had very little labor shortage or turnover, and these were not greatly affected. A few plants, anticipating the situation, strengthened their training facilities and actually were able to show a better experience during the second period. This gives great credence to the value of organized training in any safety program. The frequency-severity ratio (F/S) shown in the last column of Table I offers

Jan 1, 1947

By S. E. Sharp, J. F. Myers

The safety data presented in this paper are based upon replies to a Questionnaire sent out to representative mining companics. The authors feel that it is a fair cross section of the milling industry, in that the 17 companies, of the United States and Canada, reporting on 22 mills, are scattered from the Hudson Bay to the Mexican border and from coast to coast. These data concern the accident records of the various plants from 1939 to 1944, inclusive and the six years are divided into two periods. The first period (1939, 1940 and 1941) represents something of a normal operating condition. The second period (1942, 1943 and 1944) represents the period of time that was most affected by war conditions. During the second period there was a high labor turnover, inexperienced workers were numerous, women replaced men in many kinds of work, a labor shortage existed more or less throughout the industry, and supervision was pushed for peak production. All of the companies reporting compiled their accident experiences for these six years in accordance with the standards set up by the American Standards Association (New York, N. Y.), consequently the tabu lated data presented herein are comparable. The authors of this paper feel that the industry as a whole is greatly indebted to the personnel of the companies that furnished these data, which make this study possible for presentation. This survey covers a total exposure of 74,528,880 man-hours, with 105,471 man-days of lost time from 870 accidents. Safety Records In Table I, the safety record is shown of the various mills reporting. The severity rate is usually conceded to be the most vital statistical figure in safety parlance, therefore the participating companies are listed in order of their severity rate for the combined six-year period, under size of organizatiori. The table also shows the frequency rate as well as the frequency-severity ratio (F/S). As noted in Table I, most of the companies suffered an increase in both severity and frequency rates during the second period; only six of the 22 enjoyed an improvement. From correspondence with the various plants, it seems that a few had very little labor shortage or turnover, and these were not greatly affected. A few plants, anticipating the situation, strengthened their training facilities and actually were able to show a better experience during the second period. This gives great credence to the value of organized training in any safety program. The frequency-severity ratio (F/S) shown in the last column of Table I offers

Jan 1, 1947

By A. L. Johnson, S. C. Lyons

A FEW years ago a leading American builder of centrifuges said, "No one uses a centrifuge if the job can be done any other way." This statement was essentially true at that time, not because the basic functional and economic principles involved did not frequently favor centrifugal methods, but rather because so many of the highly specialized features of the mechanical and functional peculiarities of continuous centrifuges had not been fully developed. The idea of using centrifuges in mineral dressing is definitely not new. There are literally hundreds of patents on centrifugal machines and processes for the mining industry. Many of them cover principles that are basic to the functioning of most centrifuges in operation today. In spite of this, until 1935, there were practically no successful applications of continuous centrifuges in the United States in the mineral industry, nor for that matter were there more than a mere handful of such machines in operation in North America in any industry. This was true despite the obvious desirability of machines that could furnish the advantages of high centrifugal settling forces in a continuous operation. The reasons for this are simple, even if not obvious: I. Finely divided solids, when thrown out of fluid suspension under high centrifugal forces, frequently exhibit physical properties (particularly rheological or flow properties) that are markedly different from those they possess when settled out by gravity alone, and machines that are not designed in careful detail to cope with these peculiarities seldom function satisfactorily. 2. Most continuous centrifuges embody a solids-conveying element in the form of a very special screw conveyor. The rotation of this member under conditions of operation calls for drive designs that were not satisfactorily provided until the introduction of the Bird gear unit about 1934. These matters will be touched on later. Continuous centrifuges are now operating successfully in the mineral industry. Some units have singly handled more than 500,000 tons of solids during the past ten years. Generally their operation has been characterized by large unit capacities, complete elimination of labor, minimum supervision, moderate maintenance and power costs. TYPICAL CENTRIFUGE APPLICATIONS Most materials classified by centrifuges are of subsieve particle size. Practically speaking, this means finer than l00-mesh. A unit of measure other than screens is needed in order to consider these products properly. Such a unit is the micron, which is equal to one one-millionth of a meter; roughly 1/25,000 of an inch. The opening in a standard 200-mesh screen is about 75 microns while a 325-mesh opening is roughly 43 microns.

Jan 1, 1947

By R. T. Hukki, P. Voutilainen

This paper describes a new apparatus for continuous wet fine-screening. Its preferred size range seems to be from 0.1 to 1 mm. The supercritical trommel screen is a short cylindrical trommel of wedge-bar type construction operated at a speed greater than the calculated theoretical critical speed and at a speed lower than the speed at which particles introduced into it will centrifuge. The paper describes results obtained with the prototype supercritical trommel screen in pilot plant scale. The results point to a high capacity and simultaneously to a high sharpness of screening. Finally, an analysis is presented of the forces acting in screening on a supercritical trommel screen. In the era of high speed, high capacity processing of raw materials the conventional slowly rotating trommel screen is often considered a relic from the times passed. A typical trommel screen is the cylindrical trommel rotated about a horizontal or slanting axis at a relatively low speed. Its screening characteristics are well known. Trommel screens of various types of construction, methods of operation, performances and other characteristics have been described in detail by Taggart.1 The theoretical critical speed of a trommel screen is defined by the same well known equation as that applied for grinding mills: where ncritical = the numerical value of the theoretical critical speed in rpm, D 1 = the inside diameter of the trommel in feet, and D2 = the inside diameter of the trommel in meters. ncritical corresponds also to the centrifuging speed provided that the coefficient of friction f between the trommel surface and the outer layer of the charge is = 1.0. In a general case: From Eq. 2 it is seen that in all cases where f < 1.0 the centrifuging speed of the trommel is greater than the theoretical critical speed. The supercritical trommel screen concerns screening operations within that speed range which is between the theoretical critical speed defined by Eq. 1 and the centrifuging speed defined by Eq. 2, under conditions such that the coefficient of friction f<1.0. It is reported by Taggartl that the optimum speed of a conventional cylindrical trommel screen 36 in. in diam was experimentally found to be about 16 rpm. From Eq. 1, the critical speed of this trommel is 44.2 tpm. The indicated optimum speed corresponds to (16/44.2) x 100% = 36.2% of the theoretical critical speed. The optimum speed range based on information available seems to vary from 33% up to 45% of the theoretical critical value. The trommel screen operated at a supercritical speed: operates at a speed greater than the calculated theoretical critical speed; operates at a speed lower than the speed at which the charge introduced into it will centrifuge; operates within the supercritical speed range in such a way that the coarse fraction of the charge must slide in respect to the inside surface of the trommel; the outer layer of the said fraction next to the screen tends to proceed in the same direction as any selected point on the trommel surface, but now at a lower speed, and indeed at a subcritical speed; allows to a certain degree adjustment of the maximum determining particle size x of the fine product simply by a variation of the speed of the trommel within the supercritical speed range. With increasing trommel speed, finer and finer material only will get the opportunity to find its way into the fine product while the screen opening remains constant. In conventional practice, the low speed trommel is generally used for sizing of coarse and medium coarse material, but seldom for fine screening. The characteristic feature of the product passed through the conventional trommel is that the determining size x of the biggest particle is barely smaller than the nominal size of screen opening. The supercritical trommel screen, on the other hand, is best suited for sizing of relatively fine material. Furthermore, the characteristic determining size x of the biggest particle in the fine product can be substantially smaller than the nominal width of the screen opening or slot. In the trommel screen best suited for the applications

Jan 1, 1965

By R. S. Shoemaker, R. M. Darrah

Expanded markets for copper in the past few years and a consequent search for new ore bodies have revitalized the widely known but seldom applied method of producing copper called heap leaching. Heap leaching is defined here as the process applied to oxide ores which have been mined solely for the purpose of leaching. In this case, all costs of mining the ore become a part (and a substantial one, as will be shown) of the cost of the copper produced, whereas in dump leaching the mining cost has already been accounted for as a stripping cost for the sulfide ore. Of course, with newly opened ore bodies, stripping costs may be divided through accounting procedures, between the copper produced by the mill and that obtained by leaching, but in general this type of operation must be economic on the basis of the sulfide ore alone. Heap Leaching Requires Low Capitalization Heap leaching, as a beneficiation method, is unique in that it is the only process used for the recovery of a metal in which the time involved from mining the ore to metal production is measured in months instead of hours or at the most, days. Then too, after the ore body has been depleted and mining has ceased, metal production will continue for some substantial period of time. Heap leaching is also unique because unlike any other method of beneficiation, metal recovery cannot be accurately forecast ahead of time and recovery will never approach that of a conventionally milled sulfide ore or even that of a vat leached oxide ore. Counter-balancing this drawback, however, is the relatively low capital expenditure necessary to put a heap leaching operation into production and the consequence that smaller ore bodies which would not support the higher capital cost involved in a vat leaching plant can be made into producers. Stated more simply, in heap leaching the operator accepts low recovery in exchange for low capital costs and low break even point. Whether the operator chooses vat leaching with its higher recovery and higher capital costs, is a mater of economics which depends in part on the nature of the ore to decide. For instance, an ore that will vat leach in 7 to 10 days using 7 pounds of sulfuric acid per pound of copper produced might use double or triple that amount of acid during the months that are required for heap leaching.

Jan 12, 1968

By T. Egleston

circumstances, would prefer the steel with which they are now familiar, to a specimen that Mr. Sandberg has described as having broken into seventeen pieces under the wheels. After blowing such low manganese steel, it may be coaxed into a rail, but it is a wonder that it holds together so long as it does, with so great a nornber of minute flaws. I would not in any way depreciate chemistry, but I think it should be kept in its proper sphere. Let the chemist look after the quality of pig metal, and apply common sense in the avoiding of extremes, then the most fastidious railroad cannot find fault with the result. PROFESSOR EGLESTON, New YORK City : It is not my place as an engineer to apologize for the chemists, but as no one seems disposed to do so, and as they have had more than their share of criticism, 1 am glad to say that I believe there are chemists in this Institute whose work and word are just as reliable, arid perhaps even more so, than that of the average engineer. But we ought to make a distinction; there are chemists and chemists. With the ordinary commercial chemist, who looks upon the science as so much merohandise, I have not a particle of sympathy; but with the chemist who looks upon his profession as engineers do upon theirs, I have every sympathy. When matiufactorers and engineers go to a chemist and ask him to make an investigation, and scretv him dowu to the lowest point, turning the equivalent of his brains into cents and mills, they ustially get an exact equivalent in poor work for miserable pay, and no one has or should have any sympathy with them, and the under these conditions has no right to ask for any, and no reason to criticise any work that he may get under such circumstances. But I am disposed to think that the chemists who have been replwented and discussed at this meeting do their work conscientiously, and that it is as reliable as that of almost any profession. I believe, however, that this problem of steel rails is being investigated in a wrong direction. I said so at the Pittsburgh meeting, and I think the discussion of this meeting will prove it to all those who have heard it. I think the chemigt is incapable of solving this problem unlees he goes very far into the domain of physical chemistry, so far that it becomes physics and not chemistry; and that the physicist will be the one on whom we must rely in the future for the elucidation of the subject. The chemist may aid the physicist, but it is my decided opinion that we are looking in the wrong place to get the explanation of the phenomena.

Jan 1, 1881

By Richard Hodgson

FMC Corporation, at their mine and soda ash refinery near Green River, Wyoming, currently mines in excess of 3 million tons per year of trona. Upon completion of the current expansion, the mine will be producing in excess of 4.0 million tons per year. The single level mine, approximately 1,500 feet in depth, is currently serviced by five (5) concrete lined circular shafts varying in diameter from 12 ft. to 24 ft. A sixth shaft is complete, but not yet operational and the seventh is currently being sunk. Two of the shafts are equipped with single drum hoists. The original production shaft is equipped with a double drum hoist. The newest production shaft and the main service shaft are both equipped with ground mounted friction hoists. These friction hoists have given excellent service and another will soon be installed as a man and material hoist at No. 7 Shaft. There are a number of advantages that the ground mounted hoist has over a tower mounted hoist. There are also operating problems common to both. FMC&apos;s original experience with ground mounted friction hoists began in 1962 with the conversion of a single drum hoist to a friction hoist. The converted hoist was an Ottumwa with a 5 ft. diameter drum and a 4 ft. face. This hoist had been installed at the No. 3 Shaft for some years prior to its conversion to a friction hoist. At the time the conversion of this hoist was made, there were no friction hoists in service in Wyoming. Wyoming mining laws required that all conveyances carrying men be equipped with safety dogs. Since it was desired that wire rope guides be used, safety dogs were impractical. Agreement was reached with the State Mine Inspectors that safety dogs would not be necessary provided that recommended rope safety factors for hoisting men would still be maintained if one hoisting rope was broken. Since-the shaft is approximately 1,500 ft. deep, the recommended safety factor is 6.0 so that this installation has a safety factor in excess of 8.0 for hoisting men when new ropes have been installed. The hoist conversion was engineered by Lake Shore, Incorporated. The friction ring was made in halves and bolted over the original drum face which had been machined to remove the grooves. The ring provided for four 3/4 in. diameter ropes on 8 inch center to center spacing. The pitch diameter of the modified drum was 72 inches. The grove liners are hald in place by hard-wood wedges bolted to the drum. The other modification required by the conversion was an increase in size of bearing caps and the hold-down bolts because of the increased force tending to lift the drum.

Jan 1, 1975

By N. L. Britton

About two years ago Dr. Newberry referred to me for study a considerable collection of fossil plants sent him by Dr. Arthur F. Wendt, engineer of the silver mines " El Cerro Rico de Potosi" in Bolivia. As I had been interested in working up the extensive accumulations of existing plants made by Dr. H. H. Rusby in the Bolivian Andes further north, and in assisting Dr. Rusby in the study of those now being collected by Mr. Miguel Bang in other parts of that country, I was glad of an opportunity of ascertaining something of the Tertiary flora of the region. I was unable to take up the subject at that time, but have since been able to conclude the investigation, and the results are here presented. At a time when the mineral resources of the Southern States are attracting such widespread interest and attention, I have thought it appropriate to give a short general description of the iron-ore deposits of a territory concerning which little is as yet known and nothing published, so far as I am aware. The data used here are due to the preliminary examinations of the North Carolina Geological Survey, on which work I was engaged during the past summer, and my acknowledgments are due to Prof. J. A. Holmes, State Geologist, and Messrs. Harris, Ashe, and Lewis, of the survey, for their co-operation in the work; also to Messrs. A. S. McCreath and C. B. White for analyses which they Kindly furnished. Other analyses were made by Mr. Charles Baskerville, assistant chemist to the survey, and this may be understood where the name of the chemist is not mentioned. All samples for analysis were dried at 212&apos; F. The accompanying map has been prepared from the revised sheets of the United States Geological Survey by Mr. H. L. Harris, and will be referred to throughout this paper. Ashe county lies in the extreme northwestern part of North Carolina, bordering on Tennessee and Virginia; it is drained principally by the north and south forks of New river and their tributaries, and is therefore on the eastern edge of the great Mississippi drainagebasin. The country is exceedingly rugged and mountainous, having an average elevation of about 2900 feet above sea-level. Jefferson, the county seat, near the center of the county, is 45 miles nearly due south from the Norfolk and Western R.R. at Marion, Va., and 30 miles northwest from the Richmond and Danville R.R. at Wilkesboro, N. C. Geologically the ore-deposits described in this paper are situated in the area of the crystalline rocks, consisting chiefly of gneiss, hornblende-schist, and micaceous schists.

Jan 1, 1893

By G. W. Ostroot, S. Shryock

Cementing deep, high-temperature oil wells where static temperatures range from 350 to 400F has become routine in the part decade. In the United States there were 271 wells drilled deeper than 15,000 ft during 1963. Many of these wells had static temperatures higher than 400F. Bottom-hole static temperatures near 700F are now realities in the geother-mal (steam producing) wells of California&apos;s Salton Sea area. The detailed planning initiated prior to drilling the wells is discussed together with the methods, materials and equipment used in solving the cementing problems which are encountered. Data are also presented that lead to development of cementing compositions that provide adequate thickening time, do not retrogress in strength, and maintain low permeability under these extreme temperature conditions. Field data include the cementing programs used on eight relatively trouble-free geothermal steam wells in the Salton Sea area. INTRODUCTION Not too many years ago cementing oil wells with temperatures in the range of 300F caused considerable anxiety. In some areas of the United States it is now fairly common to cement wells having bottom-hole static temperatures in excess of 400F. We are now confronted with the problem of cementing wells with temperatures ranging from 500 to 700F. Temperatures in this order of magnitude are often found in geothermal steam wells. From where does this extreme heat emanate? There are many theories as to the source of this steam flow. The most widely held views are: (1) heat- ing of ground water fairly close to the surface by an intrusive mass of hot rock; (2) steam generation from a reservoir of metamorphic rock, normally found below 25,000 ft and not at the shallower depths of the Salton Sea reservoir; and (3) high-temperature gases (water vapor) escaping and migrating from molten or semi-molten rock (magma) at a considerable depth. Of these. No. 3 seems to be the most generally acceptable explanation. Heat from springs and fumaroles has been used for years as a means of heating and cooking; however, significant progress in harnessing the vast power of underground steam reservoirs has been relatively slow. The first large-scale attempt to use the heat generated by steam from wells was made in Italy around the beginning of the 20th century. In excess of 250,000 kw of electrical power is now being produced from holes around Larde-rello, Italy. Another very active drilling program was initiated in the volcanic area of New Zealand in 1949.&apos; Natural steam for power projects in the United States began in the early 1920&apos;s. An early commercial steam field is located at the Geysers, approximately 75 miles north of San Francisco, an area discovered in 1847 and used for many years as a health resort. Steam originates from 15 wells that have been drilled since 1957. The present output from this project is 25,000 kw. Success of the Geysers operation has been responsible for several companies taking a careful look at the feasibility of producing steam for power generation in the Salton Sea area of Southern California&apos;s Imperial Valley. Geothermal steam activity in this latter area began in 1961 when O&apos;Neill, Ashmun and Hilliard completed Sportsman No. 1, at that time the hottest wellbore in the world.&apos; Since its References given at end of paver. completion seven additional wells have been successfully completed in this area. Many problems encountered in drilling steam wells had to be overcome to make the ventures successful. Formation temperatures encountered in the Salton Sea seemed to be a straight-line function (a gradient of 13F per 100 ft of depth).&apos; This imposed severe conditions on all aspects of drilling and completion. This varied, to some extent, from gradients in the older geothermal areas. Not to be overlooked is the effect of these temperatures on casing creep or elongation by thermal expansion (Table I), because standard API flanged wellhead equipment makes no provision for this kind of performance. Floating equipment was redesigned, and changes in types of downhole equipment were made in an effort to eliminate anticipated problems. In the later completed wells, standard oil-well cementing equipment has been used. During the early development of geothermal steam wells there were some problems resulting from blowouts. However, these were eliminated in the deeper Salton Sea wells and no problems were encountered with the drilling mud. A sodium surfactant mud was used on the Sportsman No. 1 to drill from 2,690 to total depth. Nevertheless, it was necessary that a cooling system be added and the mud cooled before circulating it back into the well. The difficulty in evaluating the size of the steam area and its potential in terms of pounds of steam and years of productivity still has not been resolved. Economic complexities have also entered into the steam play in the Salton Sea. The wells at the Geysers were drilled at a cost of $15,000 to $20,-000, whereas the Salton Sea wells will cost more than $150,000. This cost differential has to some extent been accounted for because of the heavily

Jan 1, 1965

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

IN THE past year, Jaffee and Campbell&apos; and Finlay and Snyder2 reported on the mechanical properties of titanium-base alloys, some of which were in the same ranges of composition as are covered in this paper. In this paper, evidence confirming that given by Finlay and Snyder on the effects of carbon, oxygen, and nitrogen on titanium will be presented; and, in addition, new data will be given on the effects of these elements on the flow properties and phase transformation of titanium. Materials and Preparation of Alloys The preparation and general properties of iodide titanium have been adequately described elsewhere.&apos; , As-deposited iodide titanium rod, prepared at Battelle, of Vickers hardness less than 90 was employed as the base metal in the present work. This was the same material as that used by Finlay and Snyder.2 The probable analysis reported by them for standard quality metal holds here also: N 0.005 pct, 0 0.01 pct, C 0.03 pct, Fe <0.04 pct, A1 <0.05 pct, Si <0.03 pct, and Ti 99.85 pct. Carbon was added in the form of flake graphite supplied by the Joseph Dixon Crucible Co. Oxygen was added in the form of c.p. grade TiO, powder, produced by J. T. Baker Chemical Co. Nitrogen was added in Ti3N4 powder, supplied by the Remington Arms Co. Individual ingots weighed 7 or 8 g. Carbon, oxygen, or nitrogen was added by placing the corresponding powder in a capsule made from as-deposited iodide titanium rods and melting the capsule with the balance of the charge. The charge was are-melted with a tungsten electrode on a water-cooled copper hearth under a partial vacuum of very pure argon (99.92 pct minimum). Melting was practically contamination free. Vick-ers hardness increases of less than 10 points were normal for unalloyed iodide titanium control melts. Nitrogen analyses of are-melted iodide titanium showed a nitrogen content of 0.005 pct, about the same as is present in the as-deposited rod. No tungsten pickup was found in a melt of iodide titanium analyzed for tungsten. Weight losses in melting nitrogen-free alloys were very small and varied consistently from nil to 0.015 g (0 to 0.2 pct). This permitted the use of nominal composition for these alloys. Chemical analyses made for carbon, which can be analyzed conveniently by combustion methods, justified this procedure. Where nitrogen was added, considerable splattering took place. Here it was necessary to analyze for nitrogen by the Kjeldahl method. The ingots were hot rolled at 850°C to about 0.045 in. thick. After hot rolling, the strips were descaled by mechanical grinding, and then given a cold reduction of 5 to 10 pct to insure a uniform thickness throughout the length of the specimen. The edge strips and the tensile strips were annealed in a vacuum of 1x10-4 mm Hg pressure for 3 1/2 hr at 850°C and furnace cooled. Methods of Investigation Hardness Measurements: At least five Vickers hardness measurements were taken using a 10-kg load on each sample in the following conditions: (1) top and bottom of each ingot, (2) top and bottom surface of as-rolled and annealed sheet, and (3) on cross-section of annealed sheet and all quenched specimens. Tensile Tests: Tensile tests were conducted on Baldwin-Southwark testing machines having load ranges of 600 or 2000 lb. Tests were made on 1-in. gauge-length specimens, 3 1/4-in. overall length, 1/2 in. wide, 0.040 in. thick, with a reduced section 1 1/4 in. long and 0.250 in. wide. Two SR-4, A-7 strain gauges, one mounted on each side of the specimen, were used to measure the strain over a limited range to determine the modulus of elasticity. After the modulus of elasticity readings had been taken, load vs. strain readings were taken, using only one strain gauge, at increments of 0.0001 in. until the yield points were passed and then at 0.001-in. increments to the limit of the strain-gauge indicator (0.02 in.). Strain readings above 0.02 in. per in. were taken every 0.01 in., using dividers to measure the strain between the 1-in. gauge marks until the maximum load had been reached. Crosshead speed, when using the SR-4 gauges, was 0.005 in. per min, and, when using dividers, 0.01 in. per min. Flow Curves: Flow curves were determined using the true stress-true strain data obtained during the tension test. The usefulness of this type of information has been dealt with very adequately elsewhere by L. R. Jackson,&apos; J. H. Hollomon,6 and many others. Flow curves of true stress vs. true strain could be converted to the more conventional cold-work curve of 0.2 pct offset yield strength vs. percentage of cold reduction by means of the transformation, 1/1 = 1/1-R, where R is the fraction reduction in cold working. Thus, the true strains corresponding to percentage reduction can be calculated, and the 0.2 pct offset yield strengths scaled off the — 6 curve by taking the true stresses corresponding to the values of 6 + 0.002 strain. Heat Treatment: For the transformation studies, the alloys were heat treated in a horizontal-tube furnace using a dried 99.92 pct argon atmosphere, and quenched into water. Essentially no contamination was found after several hours of heat treatment at temperatures up to 1050°C. Metallography: Specimens were prepared in the

Jan 1, 1951

By W. C. Smith, P. J. Hickey

After a short historical background of the process evolution, this article descvibes present-day plant facilities and operating techniques utilized for high-purity bismuth production. The plant is one of the world&apos;s largest, with an annual output of some one million pounds of refined bismutlz. PREVIOUS papers1 written by staff members of Cerro de Pasco Corp. have referred briefly to the production of refined bismuth. Since the Corporation is one of the world&apos;s foremost producers of high-purity bismuth, a detailed description of the process for extracting the metal may be of general interest. Following a short historical background of the development of the actual process, this presentation will trace the progress of bismuth from its entry into the primary smelting circuits to its concentration in electrolytic lead cell slimes. Our facilities for the treatment of anode muds will be described and the extractive methods given in some detail, with particular emphasis on the techniques which result in the production of refined metal. HISTORICAL BACKGROUND Shortly after Cerro de Pasco began smelting operations at Oroya, Peru in 1922, it became apparent that the dust carried by copper converter gas contained appreciable amounts of bismuth. Although dust collection efficiency was poor prior to building of the 550-ft stack and installation of the central cottrells in 1938, a large stock of dust was accumulated during the intervening years, having the following approximate composition: Oz. per ton Ag - 11.0 Pct Sn — 0.5 Pct Pb - 49.0 Pct Zn - 6.5 Pct Bi - 2.0 Pct Insol. - 1.5 Pct Cu - 0.7 Pct Fe - 2.3 Pct Sb - 3.0 Pct S - 10.0 Pct As - 7.5 In the mid-1920&apos;s, experimental crucible melts of this dust with carbon indicated that most of the bismuth and silver, and some of the lead, could be reduced to a fairly clean bullion. Other products were a small amount of leady copper matte and a slag high in zinc, arsenic, antimony, and lead; this slag contained some tin but only small quantities of silver, bismuth, and copper. After the laboratory results had been confirmed by operation of a small reverberatory, a dust reduction furnace was constructed. The ±10 pct Bi-Pb bullion produced from this operation was stocked until 1930, when an Oroya-designed converter type furnace3 was installed for the elimination of arsenic, antimony, and some lead from the bullion. This process concentrated the bismuth from 10 to about 60 pct. By means of the bismuth process developed4 by W. C. Smith at East Chicago (1909-1914) and the discovery of a method5 for separation of lead from bismuth with chlorine gas in 1929, it became possible to begin production of refined bismuth. Unfortunately, bismuth deleaded with chlorine always contained residual chlorides, and the removal of the chlorides by caustic soda left a lead content of 0.02 to 0.04 pct. This final problem was solved6 by substitution of air-blowing for the caustic treatment, which effectively removed all excess chlorine and gave bismuth which was practically lead-free. In 1934, a pilot electrolytic lead refinery began operations at Oroya. Lead smelting was resumed in 1935 and two years later a 100-ton-per-day lead refinery was put into service. In conjunction with the latter, the present-day Anode Residue Plant was constructed. Until 1940, the plant treated both lead anode slimes and dust reduction bullion. The dust reduction furnace was shut down in that year, and all cottrell dusts (with the exception of the product from the arsenic cottrell) were mixed with pyrite and treated in a Wedge roaster to eliminate all possible arsenic. Calcine from this operation joined the sinter plant feed; hence the bismuth from the copper and lead circuits was collected in the lead bullion and subsequently in lead anode slimes from the electrolytic lead refinery. The latter source has been the only bismuth-bearing material of any consequence entering the Anode Residue Plant from late 1940 to the present. A copper refinery began operating in 1948, and the cell mud from this plant is mixed with lead slimes and processed through the same circuit, though only a small quantity of bismuth is present in electrolytic copper cell residues. BISMUTH INTAKE Present-day routes which are followed by the new bismuth feed from its entry into the primary smelting circuits to its arrival at the Anode Residue Plant are traced schematically in Fig. 1. As illus-

Jan 1, 1962