Search Documents

By Dale E. Walker

The Captain mine came into being under the following circumstances: 1) Commonwealth Edison had need for fuel for the generation of electricity in their Chicago service area. 2) Southwestern Illinois Coal Corp. had an ample supply of coal in the Illinois No. 6 and No. 5 seams. 3) The Gulf, Mobile & Ohio R.R. had a one-line transportation system with the capability of transporting coal from the Captain mine to Commonwealth Edison. These fortuitous conditions permitted an effective three-way partner- ship to develop. Commonwealth Edison had built a new generating station at Joliet, Ill., across the Illinois River from the existing station, to supplement their power-generating capacity for the Chicago area (Fig. 1). The annual requirement of the Joliet station is approximately 4.5 million tons of coal. From large reserves of coal in the No. 6 and No. 5 seams, Southwestern Illinois Coal Corp. contracted to supply Commonwealth Edison with approximately 6 million tons annually from its Captain mine. The logical carrier was Gulf, Mobile & Ohio, whose mainline travels through this coal field and also passes by the Joliet station on its way to Chicago. This railroad has been moving Southwestern's coal from the Streamline mine for more than 30 years. The basic ingredients of timing, scheduling, moving, and handling were adopted by the three parties, the precise details being worked out jointly. To do this, each group had to know its requirements exactly. The initial schedule was drawn up and tentatively approved, with each party taking a hard look at its own requirements and commitments to make certain that the schedule could be met on a normal daily basis. With only minor changes, the final schedule was adopted, each participant feeling that it had a sufficient factor of safety to maintain steady operation. Each party agreed to help the other in time of emergency. When a delay occurs in any part of the operation, the other

Jan 1, 1969

By James Quigley

As the outcrop mines in the West developed into underground operations, systems of ground sup- port were gradually evolved. In the early coal mines there was little need for support except near the dirt line in portals, where stone masonry was common. Where the top was shaley or broken, native pine props with light cross bars and legs furnished enough support even in Utah's 25-ft coal seams. As depth of workings increased, roofs and backs of the same general nature as those near the surface became more and more unstable and required more and more support. Some coal airways show this tendency very clearly. From the surface down the same type of roof shows deterioration which an experienced eye can translate into a measure of depth under surface rather than change in rock characteristics. Rock bolts, developed by various companies and by the U. S. Bureau of Mines, have become an effective substitute for timber in sections of some metal and nonmetal mines formerly requiring excessive timber support, and further use of war surplus landing mats, chain link fencing, and a new punched channel developed by one of the steel companies has enabled other mines to operate deposits where costs of timber and lack of clearance for timber support would have prohibited mining. The block caving mines have made extensive use of reinforced concrete underground to achieve similar ends under difficult conditions. Steel sets are standard in many Bureau of Reclamation projects, although these are usually covered in with concrete to make the permanent structures the Bureau's reclamation projects require. But the use of steel in mining operations is limited and has been confined principally to the iron ore mines of Michigan, Wisconsin, and Minnesota. Some mines have installed used rail as posts, caps, and crossbars, but a rail section is not suited for load carrying, and used rails are generally brittle, having a tendency to fail without warning when overloaded.

Jan 7, 1959

By Robert Ignouf

MY REMARKS, which I feel highly honored in being invited to make, shall be limited to a consideration of -the mining and metallurgical problems involved in this question; in fact, these problems alone might well be considered as suffi¬cient to explain the existence of the Ruhr situation and to justify the steps taken by France in this affair. Comparing the France of pre-war days with the France of the period following the Versailles treaty indicates clearly how the Ruhr question is a direct consequence of the new economic conditions which have prevailed in Europe since peace was signed between the Allies and Germany. Before the war, in 1913 for instance, the French out¬put of iron ore was 22,000,000 tons. This output, which decreased considerably during and immediately after the war, has about regained its previous level. It should be noted that 96 per cent. of the production of iron in France is obtained from the eastern part of the country, in the districts of Nancy, Briey,. Longwy, Metz, and Thionville. This concentration of practi¬cally all the iron mines into one district creates a very serious problem for France, involving strategic and economic consequences. The strategic problem arises from the fact that the whole iron resources of France lie close to the frontier of Germany, at a distance of only a few miles; hence it is of the' utmost importance for France to be assured that her eastern frontier shall not be at the mercy of a sudden invasion by an army which could in a few hours deprive France of her iron resources and render her powerless to defend herself. Invaded by her Eastern neighbor three times during the past 100 years, France has had dire experience with what such invasions mean for her. Wherever the German armies have passed, they have left an inefface¬able trail of desolation. France, therefore, intends to protect herself by sufficient and efficient guarantees against renewed invasions of her territory.

Jan 5, 1923

By Joseph E. Pogue

Any mechanism, either natural or artificial, for regulating the functioning of a given unit in the general economy must operate toward the maintenance of equilibrium if it is to survive. The petroleum industry, concerned as it is with the production of a natural resource of specialized character, is surrounded not only by the economic factors common to other industries but by an extra set of unique elements centering about the fugitive character of crude petroleum under conditions of competitive development. The term equilibrium, therefore, so far as the oil business is concerned, involves a combination of economic and physical factors: the first set having to do with supply, demand, costs, profit margins, purchasing power, and the like; and the second, with underground pressures in oil pools, efficient rates of extraction, and all other aspects of engineering that may be summarized by the familiar term "conservation." The two categories, in fact, are not as clearly divided as the foregoing statement would imply, for in practice it will be found that the economic and physical aspects have a pervasive interaction and interrelationship. If the development of the petroleum industry in the United States is examined from its inception in 1859 down to the present, it will be found that, beginning about 11 years ago, a new mechanism for regulating the production of crude petroleum made its appearance. Prior to this recent period, the production of this raw material was determined by competitive forces operating without outside restraints. At present the output of crude oil is subjected to supervision by regulatory bodies in most of the oil-producing states, which impose upon the operators certain conditions having to do with the manner and rates of production. Thus, in the space of a decade, the mechanism for producing crude oil has changed from an automatic to a designed procedure called proration. And in its short history this method has been marked by a rapid evolution in its nature and incidence, with progressive changes still under way.

Jan 1, 1938

By George J. Young

The nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker's stand-point has also received much comment, arid scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of niore intensive study and experimeritation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has been written concerning an accurate definition of the term "slime," but no comprehensive definition seems to be gcnerally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may bc and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles niuch more slowly and finally a certain portion remains

Jan 1, 1912

By H. L. Hopkins, OHIO, L. W. Kemph, CLEVEL AND, E. V. Ivanso

A balanced system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internaI stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced during the commercial heat treatment of aluminum alloy products. As the industrial use of aluminum increases, it is inevitable that products of increasingly large volume will be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling from elevated temperatures is that of the size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high elastic limits. On the other hand, all commercial aluminum alloys have relatively high thermal conductivities, no invariant phase changes, and the quenching temperatures are comparatively low. In the absence of invariant phase changes involving change in the type of crystallographic lattice, the fundamental basis for the development of internal stress

Jan 1, 1934

By Neil Johnson

IN the cyanidation of gold, silver and mixed ores, the solids suspended in the pulp after fine grinding, primary settling and series agitation are subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D. The conventional C.C.D. plant consists of a series of separate thickeners-three to five in number-arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they are diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D. plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in series instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and seal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-ance with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a dia-phragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

An Outline Classification of Mining Systems for Ore and Coal. See COAL Progress at the Homestake Mine. By Guy N. BJORGE. (Min. & Met., June, 247. 4400 words.) Homestake's mining methods today are controlled to a con¬siderable extent by that which has been done in the past. The two main operating shafts were begun m 1878 and 1896 respectively, so that the location of shafts, loca¬tions of all the drifts on the upper levels, and a great deal of stoping was done before any of those now connected with the mine had anything to do with it In this paper is described the general plan of development. A table shows percentage of total production mined by the different methods in recent years. Average daily produc¬tion for several years now has been about 3850 tons milled. With the present schedule of 6-day operation of the mine, that means about 4450 tons a day mined This ore is treated at three plants, with respective capacities of 2000, 1200 and 600 tons The principal novelty in milling is at the largest mill where the stamps are used as crushers only, and where in the last two years a notable increase has occurred in the size of screens used A unit has been added to cyanide plant No 3 The construc¬tion of a new shaft is described, as is also the hoist building The company operates its own lumber and timber department It has a well equipped hospital Housing at Lead is an individual matter. Rejuvenating the Golden Chariot Property in Idaho. By R. S. MCCLELLAN (Min. & Met, November, 443. 2300 words) An effort to rejuvenate the Golden Chariot group of properties near Silver City is now being carried on by the John Hays

Jan 1, 1935

By Louis D. Huntoon

The Hammond Mining and Metallurgical Laboratory is the gift of Prof. John Hays Hammond to the Sheffield Scientific School of Yale University. Professor Hammond was graduated from this school in the class of 1876, and has always shown great Merest in its welfare and progress. In 1903, he offered to build and equip for it a mining and metallurgical laboratory. This offer was gratefully accepted by the trustees; and in October of the same year the architect, W. Gedney Beatty, and I were employed to draw up plans for the building, which is the largest of its kind in this country. The Treasurer's report shows the total gift of Professor Hammond, including land, building, and equipment, to have been $128,741.53. This does not include $5,000 given by Professor Hammond to defray incidental expenses. The detailed cost of the machinery and installation, included in the above sum, is as follows: Macbinery,.......$9,846.00 Pipe and fittings,......925.05 Hangers, shafting, pulleys, belts, etc.,.. Steel-work, tanks, launders, etc.,...272.19 Screens for sizing ore,.....411.37 Lumber,.......1,896.36 General Supplies : Hardware,......$135.96 Tools,.......263.66 Paints,.......204.63 Electric and incidental,.... 439.57 ----------1,043.82 Machine-shop material, . 259.44 Labor,.. 722.29 ----------981.73

Jan 1, 1910

By Robert Phelps

A STUDY of solid solutions has long been a source of interest because of the conditions -controlling their formation. X-ray investigations so far have been conducted with the idea that there were two types of solid solutions. In the first type, an atom of the solute was supposed to replace an atom of the solvent in the crystal lattice. In the second type, an atom of the solute was supposed to lie in one of the interstices between the atoms of the solvent. These pictures both require that the sizes of the atoms must play an important part in the process of solution. It is the purpose of the present investigation to study the mechanism of solid solution, using pure silver as the. solvent, and pure aluminum as the solute. X-ray measurements show that these elements have the same "shape" of atomic domains (they both crystallize as face-centered cubes) and that their atomic diameters differ by less than one per cent.1 The results of the present investigation point toward a chemical rather than a physical picture of the nature of solid solution, and make the older' pictures merely special cases of a more general picture. The new theory has the advantage, too, that it offers a rational explanation of certain phenomena which hitherto have been only interesting detached facts. The aluminum-silver system which was, chosen for this study has been studied by various methods by several workers. By means of thermal analysis Gautier2 and Petrenko3 have determined the phase diagram. Hansen4 studied the aluminum-rich alloys by means of thermal and microscopic analyses. , He showed that at high temperatures silver dissolved in aluminum to the extent of 47 per cent by weight at 5600 C. But this solubility decreased to 1 per cent at 200° C. Westgren and Bradley5made an extensive X-ray study of these alloys. They used the change in the lattice parameter of silver as a criterion of the solution

Jan 1, 1932

By Allen Garrison

IT is the purpose of this article to present. the results of an investiga-tion of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results, upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instru-ment adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.1 It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observa-tion of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1939

By A. K. Schellinger, R. D. Lalkaka

IF the ball mill is considered only from an energy standpoint, it can be thought of as a converter of kinetic energy into heat energy and surface energy. The law of the conservation of energy must apply to the ball mill as it does to any machine or process in nature. The heat energy output of the ball mill is apparent to any casual observer of the operating mill since the outflow pulp will be appreciably warmer than the inflow water and rock. The rock in the ball mill is crushed by shearing of its ionic bonding caused by some impact-induced stresses beyond the elastic limit. As the bonds holding the mineral crystal lattices together are ruptured, new surface area is created on each unit of which a definite number of unsaturated bonds exist. Such unsaturated energy of bonding may be termed the "surface energy," and is a potential energy figure. This created energy was withdrawn from the ball mill system and represents an absorption, or disappearance of heat. To reduce the size of the rock, surface area must be created and with it the at- tendant characteristic surface energies of the minerals concerned. Thus the creation of surface energy, from an energy viewpoint, is the creation of useful work by the ball mill. Because of the controversial nature of the energy efficiency figures for modern operating ball mills, it seemed worthwhile to approximate the ordinary magnitude of such efficiencies from the above viewpoint. This was done by an energy balance of the three aforementioned forms of energy, kinetic, heat, and surface energy, for two 9Y2x10-ft grate-type ball mills grinding cement raw materials. Kinetic energy input to the balls was approximated as closely as possible while the heat energy output was measured by means of a thermometer and water and rock flow rates. The assumption was made

Jan 1, 1952

By C. D. King

DURING the 30-year period spanned by these annual Howe Memorial presentations, many lecturers could proudly claim a kinship either as a student or an associate of the man whose memory we honor. Although it has been my good fortune to have attended many of these annual lectures, it was not my privilege to have known Henry Marion Howe personally. However, his great repute as teacher and scientist was known to all undergraduates of my day and the later years have enhanced my appreciation of his wisdom and foresight. Those who knew him well have said he derived particular pleasure from speculations on the future world of metallurgy. For this reason, I feel that perhaps he would not be unsympathetic to a lecture in his honor which departs from the highly instructive scientific presentations made in the past by so many able Howe Memorial lecturers, and which is concerned more with the practical phases of various steelmak-ing processes and some speculations on their future form and relative importance. The word "revolutionary" is frequently applied to each seemingly important improvement in the production of steel ingots, but in retrospect these changes, impressive as they appear at the time, are merely steps of progress. In the hundred years from the inception of tonnage steelmaking, only three processes can be truly classified as revolutionary. They are the pneumatic process, known in this country as the bessemer process; the reverberatory method called the open hearth process; and, the electric furnace process. There have been many variations and combinations of the three fundamental methods, but they remain truly the only revolutionary methods in steelmaking since its early history. Everything else has been evolutionary, in effect. doing the same things that we have done in the past but doing them better, correcting our errors through experience, and slowly but inevitably reaching a higher state of accomplishment. It has often been said that coming events cast their shadows before, and the production of steel ingots is no exception. As a result of the unrelenting demands of World War I1 and the years that followed, truly impressive progress has been made in steel ingot production. The incessant pressure for immediate results during this period required the employment of initiative and daring, as in few past decades, and many developments were brought to fruition. Of equal importance is the possible effect on future steelmaking methods of the many ideas initiated but still in formative stages. Fig. 1 portrays ingot production in the United States by the three fundamental processes over a period of 75 years and is interesting because it poses some questions as to future trends. The early ascendancy of the bessemer, its replacement in importance by the open hearth process, the amazing growth of the latter, and the recent challenge of the electric furnace are evident from the chart. Management is fully aware of these changes, but is even more interested in the future trends. Our concepts of the relative importance of the more recent developments and their possible effect on future processes may perhaps be best exemplified by a specific, hypothetical problem. Let us assume management is contemplating a new ingot producing plant with an output of 100,000 net tons per month, located in an area where some purchased scrap may be obtained but where by far the largest component will be own-produced blast furnace iron. Management requires a process or combination of processes which will yield highly uniform quality characteristics in the ingot form, and represent the soundest selection in investment and operating cost. Under these conditions, the obvious selection for the past four decades has been the open hearth process but, in view of more recent developments, management may believe that it is no longer permissible to disregard other possibilities with impunity. Accordingly, to be assured of the best possible selection, they request that you review not only the possibilities of utilizing the conventional open hearth, duplex, bessemer, and electric furnace methods, but also the more recent developments, such as the turbo-hearth, the Linz-Donawitz method, the Perrin modifications, and other possibilities. With this background, one might then appraise the relative importance of these methods to meet a specific need, and concurrently speculate on the forms that future ingot processes will assume and the relative importance of these processes.

Jan 1, 1955

By V. W. Bihlman, H. M. Williams

In the construction of internal-combustion engines, the cooling of the combustion chamber and pistons is of great importance. In certain types of engines, the adequate dissipation of heat from the bearings is also important. One of the important factors affecting heat dissipation from these parts is the thermal conductivity of the material used. A search of the technical literature shows that, in general, the thermal conductivity of the elements1 has been determined accurately by a number of investigators. The data on the industrial alloys are, however, meager. For an investigation of these alloys, the thermal-conductivity apparatus described in this paper has been constructed at the laboratory of the General Motors Research Corporation. It is desirable that an apparatus for work of this nature should give fair accuracy of results with a convenient form of specimen and a reasonable rapidity of operation. A summary of the different methods of determining thermal conductivity is given in the first volume of the " Dictionary of Applied Physics," pages 429 and 470. The method selected as best satisfying these conditions is that of Griffith, on page 443, with the addition of a guard ring similar in principle to the method used by Berget (P. 445). Briefly, the method consists of heating one end of a bar T, Fig. 1, electrically, measuring the amount of heat transmitted through the bar by a flow calorimeter J fastened to the other end, and measuring the temperature gradient along the bar. To compensate for the loss of heat laterally, the test bar is surrounded by a guard ring E, in the form of a steel pipe, which is electrically heated at the bottom and cooled at the top with a

Jan 1, 1923

By V. W. Bihlman, H. M. Williams

In the construction of internal-combustion engines, the cooling of the combustion chamber and pistons is of great importance. In certain types of engines, the adequate dissipation of heat from the bearings is also important. One of the important factors affecting heat dissipation from these parts is the thermal conductivity of the material used. A search of the technical literature shows that, in general, the thermal conductivity of the elements1 has been determined accurately by a number of investigators. The data on the industrial alloys are, however, meager. For an investigation of these alloys, the thermal-conductivity apparatus described in this paper has been constructed at the laboratory of the General Motors Research Corporation. It is desirable that an apparatus for work of this nature should give fair accuracy of results with a convenient form of specimen and a reasonable rapidity of operation. A summary of the different methods of determining thermal conductivity is given in the first volume of the " Dictionary of Applied Physics," pages 429 and 470. The method selected as best satisfying these conditions is that of Griffith, on page 443, with the addition of a guard ring similar in principle to the method used by Berget (P. 445). Briefly, the method consists of heating one end of a bar T, Fig. 1, electrically, measuring the amount of heat transmitted through the bar by a flow calorimeter J fastened to the other end, and measuring the temperature gradient along the bar. To compensate for the loss of heat laterally, the test bar is surrounded by a guard ring E, in the form of a steel pipe, which is electrically heated at the bottom and cooled at the top with a

Jan 1, 1923

By Joseph B. Umpleby

The oil industry is at the parting of the ways in relating fundamental engineering concepts to legal interpretations and field practices. The old concept, based on an erroneous analogy to wild game, that oil and gas are migratory substances and belong to him who reduces them to possession regardless of their point of origin in the reservoir, has come to be quite generally recognized as the basis of many of the serious ills and extravagances of the industry. The chain of consequences resulting from this erroneous conception has been traced elsewhere and need not be recounted here. The important problem at this stage in the development of the industry, when laws are being revised by legislative action and modified by court decisions; when added powers are being exercised by voluntary committees and official regulatory bodies; and when the need for control of output has forced itself to the forefront, is to see to it that new law and action are based on sound engineering concepts. Reservoir Energy Common Property Since the study of gas instituted by the Marland committee of the American Petroleum Institute in 1927, a great mass of information has accumulated concerning the function of gas in the development and production of oil. This wealth of data leads to the conclusion that every oil pool contains three resources: Oil, gas and reservoir energy. I take it that the central problem of this symposium is the ownership of these three resources and that "source" and "utilization" are involved because of their bearing on ownership through the demands of equity and conservation. In order to facilitate the discussion, permit me to state categorically, that: The oil and gas in a particular tract should belong to the owners of the mineral rights in that particular tract, but the reservoir energy should be common property of all owners of mineral rights in the pool I take it that apportionment of oil and gas among owners according to the relative amounts that exist in place in their respective tracts is

Jan 1, 1933

By Grafton M. Thrasher

For the proper discussion of this subject it is necessary to incorporate in this paper the substance of part of an article published by me in Metallurgical and Chemical Engineering for January, 1915. Several years ago, while I was chief chemist for a malleable-iron company, it occurred to me that the mere regulation of silicon was not sufficient to produce the desired degree of chill. But only after repeatedly encountering this fact in both open-hearth and air-furnace, as well as cupola metal, was I led to regard variation in the total carbon as the principal cause of disturbance; and I resolved to determine the total carbon as well as the silicon in every heat, and by a carefully prepared test piece to gauge the approximate degree of chill. The test piece selected was a round plug, 2 in. in diameter and 12 in. long, cast on end

Jan 1, 1916

By Samuel S. Wyer

The art of natural-gas compressing is now over 25 years old, and has grown at practically the same rate as the increase in domestic natural-gas consumers. There are now over 200 natural-gas compressing stations in North America, aggregating more than 320,000 hp. of compressor capacity and representing a property value of more than $22,000,000, and compressing more than 85 per cent. of all the gas used. The age and magnitude of the art make it evident that the use of gas compressors is a recognized integral part and universal custom of the natural-gas business. The public also is not without its rights and vital interests in this problem. Approximately 1,700,000 domestic natural-gas consumers in North America are dependent upon gas compressors for their natural-gas service. That is, if the use of compressors were to be prohibited, the majority of these consumers would be unable to secure adequate natural-gas service. Each consumer represents between four and five persons, and it therefore follows that the comfort and well-being—as far as natural-gas service is concerned—of at least 8,000,000 persons would be affected if the use of natural-gas compressors should be prohibited. These 1,700,000 consumers have invested, in services, house piping, fixtures, and appliances, an average of about $90 each, or an aggregate of $153,000,000, which is much more than the companies' investment in gas compressors. Furthermore, in all cases where the rate paid by the consumers is fair to the gas company—considering the value of the service rendered by the gas company—the consumers are entitled to continued service and protection of the investment they have made on the faith that the gas service would be continued in the future. Since "Customs adopted and acquiesced in, if not in conflict with federal or State legislation, have the force of positive law,"l and ('Courts will take notice of whatever ought to be generally known withxn the limits of their jurisdiction,"2 there ought to be no question as to the un-

Jan 1, 1916

By Harry L. Brown, Philip E. Armstrong

Young's modulus doto ore presented for W, Mo. Ta. V, Cr. Ni, Ti, and Zr as a function of temperature up to about 0.7 of the melting points. A plot of reduced temperature us reduced modulus produces a general correlation except for titanium and zirconium. Young's modudlus data for some representatiue commercial graphites are given up to 2400°C. All results were obtained from longitudinal resonance-frequency measzrrements of 4-in. long samples, corrected for simultaneously measured thermal expansion. Comparison of poly crystalline and single-crystal tungsten behavior indicates that all the observed modulus values are frequencv -dependent at the higher temperatures. STATIC measurements of elastic properties of materials at elevated temperatures are extremely difficult to make since the elastic behavior is obscured by relatively large first-stage creep effects. Dynamic methods which avoid this difficulty by utilizing the measurement of the resonance frequency of a simple vibrational mode have been described in the 1iterature.l-3 The authors have extended the operating temperature range of this type of measurement to above 2000°C and have described the equipment elsewhere.~ The Young's modulus data presented here were obtained with this equipment, using samples about 4 in. long and 1/4 in. diam, supported horizontally at the center and excited to the fundamental longitudinal resonance frequency. Young's modulus was calculated by the formula: E = 4f2f2p where E = Young's modulus, / = frequency, 1 = length, and p = density. Dilatometric data were obtained simultaneously by optical measurements of the change of length of the sample. For the metals tested, an attempt was made to obtain modulus values that would be representative of the pure, strain-free, randomly oriented material. All of the graphites studied exhibited a high degree of elastic anisotropy, while the method assumes an isotropic homogeneous material. However , when the values for Young's modulus obtained for AUC graphite were compared with those taken from static measurements at room temperature they were found to be only about 4 pet higher. This is excellent agreement considering the low precision of modulus calculations from stress-strain curves. The difficulty in using data of apparent Young's modulus for anisotropic materials arises when the attempt is made to use these data and shear-modulus data to obtain Poisson's ratio. The results are usually meaningless and sometimes absurd.' RESULTS Table I lists the sources, impurity content, thermal history, and dilatometric constants of the metal samples that were investigated. All the metal samples were tested under a vacuum of 1 to 5 x 10-5 Torr. Where our dilatometric data agreed with previously published data, the table lists the previous values and the literature reference. Where no reference is given, the constants were determined from our dilatometric data. Table II presents the modulus data in units of millions of psi as a function of temperature in degrees centigrade. The numbers were obtained from curves fitted to the experimental data. For some types of calculations, such as those attempting to correlate creep data, the slope of the modulus curve is of interest, and this information also is reported in Table 11. It is always tempting to try to fit physical-property data into some general pattern and then use this pattern to predict the behavior of other similar materials. The general pattern for an elastic modulus of a metal seems to be a linear deoro- with increasing temperature Over the range between 0.1 and 0.4 of the melting temperature, then a progressive1y decreasing value up to the melting point. Metals appear to retain finite moduli

Jan 1, 1964

By John Jermain Porter

THe value of any particular ore, coke, or limestone, for iron-making, depends upon its effect, first, upon the quality or value of the resultant product; and second, upon the cost of smelting. The factors under the first head are the percentages of phosphorus, manganese, and other elements, which remain in the pig-iron ; while those under the second head are the percentages of iron, carbon, or lime, the slag-forming constituents, which must be fluxed, and any other ingredients which give rise to variations in cost of fuel and flux. The first of these criteria of value is perhaps not capable of being reduced to a general formula embracing all cases, since it must vary to a great extent with market-fluctuations. For example, Bessemer pig is worth sometimes more and sometimes less than foundry-pig; and the premium paid for high manganese varies within wide limits. The second, or smelt-ing-value, however, can be expressed numerically with a fair degree of accuracy; and it is with this phase of valuation that the present paper is concerned. The utility of a means of comparing numerically the relative smeltiug-values of difierent ores, cokes, and limestones, is self-evident, although it may not have importance in Northern practice, where materials are largely standardized. On the other hand, there are, especially in the South, many furnace-managers who must use a great variety of materials of widely varying grade; and it is with special reference to this district, and in connection with the efficiency-methods which I have elsewhere proposed,' that the methods herein described were devised.

Jan 1, 1913