Search Documents

By Jean Balech

This paper presents some results of dynamic loading tests performed on concrete piles driven in soft clay formation. The load transfer mechanism, measured in the dynamic increasing energy test (DIET), under blows of growing energy, is described in terms of mobilized normal forces diagrams and unitary local friction and displacements. It was observed that the lateral skin friction grows up to a maximum, in the soft clay layer and, gradually diminishes to a residual value when the system presents the maximum mobilized resistance. It may be concluded that the rupture load is not equal to the maximum mobilized point resistance plus the maximum mobilized local friction as suggested by most of static bearing capacity formulae.

Jan 1, 2002

By O. U. Bradley

THE extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, somelosses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. , Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 13 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of. 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause, more or less deterioration in quality, particularly when the fresh production is run direct from the. gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks.

Jan 7, 1918

Due to deposit shape and dimension, narrow vein makes reserve modeling, geological control, stope design, drill and blasting more challenging. It needs high standard quality control as errors can be created easily, which could cause significant amount of ore loss or dilution. From channel sampling, survey control, reserve modeling, drill hole design, blasting, communication with underground drillers to backfill, this paper illustrated every step and its quality control of a long hole stope mining. Compared to other narrow vein mining methods (cut and fill and shrinkage), long hole stoping means higher production, less labor, and significantly lower cost when deposit characteristics allowed.

Jan 1, 2012

By Bernardo Araya López

Dada la competitividad que existe en el ambiente empresarial durante los últimos quince años, las empresas reaccionan rápidamente ante los cambios del mercado. En este sentido, el presente trabajo señala el proceso de organización que la empresa debe considerar para lograr sus objetivos y metas. De forma, que la gerencia como concepto de gestión, genere confianza y responsabilidad sobre sus subordinados y potencie las habilidades de sus trabajadores.

Sep 13, 2001

By J. A. McCamley

Gypsum scrap generated from wallboard manufacturing, construction and deconstruction activities in North America, Europe and Japan is a recognized environmental problem. Landfill disposal of this gypsum scrap is problematic, with deposits often creating hydrogen sulphide emissions and metallic sulphide groundwater leachates. Of these regions, Europe is the most advanced in dealing with the issue having enacted legislation, which will come into effect in July 2005 that will strongly encourage gypsum recycling throughout the EU. An estimated 10% to 17% of all gypsum used in the wallboard industry becomes recyclable scrap, which represents approximately 1% of the total waste stream in North America. In the United States, 2.5 to 4.5 Mt of gypsum scrap is generated each year; the volume is similar in Europe (the percentage of total tonnage is less because of the higher use of brick and concrete). The Greater Vancouver region of British Columbia has banned gypsum from its landfills, and as a result, all gypsum scrap is now recycled. New West Gypsum Recycling, a Canadian firm, uses its proprietary technology to process large quantities of gypsum scrap that is reincorporated into new wallboard, at percentages ranging up to 25%. The operation of New West Gypsum Recycling Inc. of Langley, Vancouver is examined as a case study and recommendations are provided as to how other urban regions can implement similar gypsum scrap recycling programs.

Jan 1, 2004

By G. S. Littlejohn

In anticipation of the flooding of an adjacent dolomitic groundwater compartment, five rough parallel sided boundary plugs at 58 and 50levels have been designed to resist safely hydrostatic heads of 1500and 1250 metres, respectively, over a service life of 100 years. Following a description of the engineering properties of the surrounding rocks, the paper details the design considerations relating to structural length and strength, hydraulic gradient, rock mass watertightness, constituent materials of mortar intruded concrete, pregrouting of permeable discontinuities within the surrounding rock mass, a bentonite barrier to resist aggressive mine water, plug tightening and design performance requirements. Routine quality control tests include permeability of the rock mass, fluidity, bleed and strength development of the intruded mortar, and temperature of the intruded concrete during curing. A special test programme includes determination of strength and stiffness of cored concrete and rock samples, shear strength of the rock/plug interface and associated in situ contact stress in order toe stimate the load safety factor against plug failure by shear.

Jan 1, 2006

East Otago gold deposits are hosted in Otago Schist that is the metamorphosed equivalent of Permian-Triassic Torlesse terrane greywackes. Relatively undeformed Torlesse sequences in Canterbury have <l m - 50 m bedding, with c. 500 m - l km and c. three kilometre scale units, typically either: 1) thick-bedded, massive, sandstones; 2) thin-bedded sandstone-argillite flysch; or 3) siltstone- or argillite-dominated units. Such lithological layering in Otago was intensely folded, deformed, and overprinted by metamorphic fabrics during Jurassic-Cretaceous regional metamorphism. Although primary sedimentary structures can no longer be recognised, a æghostÆ lithological variation is still present in Otago represented by psammitic (sand-derived), interlayered (sandstone-siltstone derived) and pelitic (siltstone-mudstone derived) schist. Lithological æunitsÆ in the schist are typically either 20 100 m or c.1 - 2 km thick, and are oblique to faults and shears hosting gold mineralisation at Macraes, Barewood, Nenthom, and Oturehua. Lithological variations and folds in lithological units are important in the along-strike distribution of gold in these deposits, and in the development of relatively high-grade pods and shoots at l00 m - 1.5 km scales. Ramps, flats and step-overs (known to be locally important for controlling mineralisation) are commonly located at lithological boundaries, presumably by local refraction of faults or shear zones as they propagated through folded stratigraphy. The various lithologies have also responded differently to deformation, causing variations in permeability that affected the penetration of mineralising fluids. Mapping lithological variations in barren host-rocks, either directly+ by fieldwork or indirectly by aerial geophysics, is a key to understanding and predicting the distribution of gold at mine and deposit scales.

Jan 1, 2001

Though many mining and mineral processing companies have embraced the principles of sustainable development (SD), there is still a significant challenge of applying these in a practical sense, either in plant design or as part of day-to-day operations. The high-level nature of sustainability concepts often do not translate easily into workable activities or business case evaluations. This makes it difficult for engineers and company decision makers to understand whether their actions are making a contribution to sustainable development and a long-term business case. While several organisations have their own SD tools that can, to a degree, help identify these opportunities, they are largely ad-hoc and lack the necessary thoroughness to defensibly value these opportunities. Recognising these serious shortcomings, the Cooperative Research Centre for Sustainable Resource Processing (CSRP) has undertaken the development and trial applications of SUSOP« (SUStainable OPerations), a new concept that is somewhat analogous to HAZOP and the wider risk and safety frameworks used in projects today. The key goal of the SUSOP« research project is to produce a holistic, systematic and rigorous framework for project development, capturing, recording and evaluating SD opportunities and constraints against a chosen sustainability structure (eg Five Capitals). SUSOP« is being developed through an iterative process with input from research institutions and engineering companies. This integrated approach ensures that SUSOP«, in its final form, will have the academic rigour and industry realism required to assist the resource sector contribute to societal sustainability by embedding the concepts and processes into the design and operation of their assets in a meaningful and practical manner. SUSOP« has created much traction with both engineering companies and mining and minerals operators. This conference paper presents an overview of the SUSOP« framework and its current suite of processes as well as highlighting, through practical case studies, its capability to incorporate SD considerations at different phases of an engineering project's development.

Jun 1, 2010

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first paper5/ dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second dealt with extraction in a mine (Crucible) in which coal was loaded. by hand and in which the rib lines wore long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central hart of Washington County, Pa. , approximately midway between the Montour 10 end Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalizations as appear to be justified.

Jan 1, 1940

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

By A. B. Fox, R. P. Thackray, K. C. Mills

The role of mould fluxes in continuous casting is reviewed. The main functions of the flux are described and the importance of the flux in providing lubrication and the right level of heat transfer between the shell and the mould is described. The major problems of longitudinal, transverse and star cracking, gas and slag entrapment and deep oscillation marks in the steel product and ?sticker breakouts? are analysed. The important physical properties of the flux in combating these various problems are identified. Physical property data for the fluxes are given.

Jan 1, 2004

By Charles L. Kusik

A study was conducted for the Bureau of Mines, U.S. Department of the Interior, to provide information which will lead to an increase in the recycling of mineral materials, in order to help conserve the Nation's mineral resources. Data were collected on energy requirements to recycle prompt industrial and obsolete scrap for nine metal commodities: Iron and steel, aluminum, copper, zinc, lead, stainless steel, titanium, tin, and nickel and nickel alloys. Major process routes for recycling were considered, starting from the first collection point through scrap preparation, transportation, smelting and/or refining to the molten metal, ingot, or other semi- finished form approximately equivalent to a primary metal of a similar composition. Available data for 1976 were collected on the amounts of each metal commodity recycled by major scrap categories. In addition, energy requirements were estimated for separating municipal solid wastes into four major categories: Refuse-derived fuel, and magnetic, aluminum, and glass cullet fractions. Finally, areas of research were identified to enhance recycling and/or increase the efficiency of energy use.

Jan 1, 1978

By M. Fan

Dry coal separation technology has particular advantages in the applications in arid and cold regions, or low rank coal separation. The hazardous pollutants in low rank coals can not be efficiently removed by conventional wet coal separation processes because a considerable amount of porose and easily friable low rank coals suffer serious particle size degradation problems in water. In this paper, a novel dry coal separation method with a vibrated air-fluidized bed of magnetic fly ash and magnetite is put forward for dry coal beneficiation. The magnetic fly ash used in this study was derived from fly ash obtained as a byproduct of coal combustion. The vibration?s effect on the uniformity and stability of a magnetic fly ash air-fluidized bed was studied. The 6×0.5 mm dry coal separation results with a vibrated air-fluidized bed of magnetic fly ash and magnetite showed that the probable error E value of separation is 0.06-0.08 t/m3.

Jan 1, 2009

By A. Gene Collins

Potassium, lithium, strontium, barium, and manganese are present in many oilfield brines, None of them except barium is determined routinely in brine analyses. Therefore, sensitive and accurate flame-spectrophotometric methods were developed. Potassium, lithium, and strontium were determined by a standard-addition technique in ethyl alcohol solutions. Barium and manganese were determined in ethyl alcohol and normal propyl solutions, respectively, after interfering substances were removed.

Jan 1, 1962

Study on Oil Agglomeration Flotation for Deinking

Sep 13, 2010

By Fred D. DeVanery

"INTRODUCTION Although galena is the most common lead-bearing mineral, is easily concentrated by gravity methods, and is readily susceptible to flotation, nevertheless some galena-bearing orebodies have within them small deposits of lead ore that fail to give a high recovery when treated by the customary milling methods.The secondary minerals, cerussite and anglesite, which result from natural oxidation of galena, cause losses when the customary method of lead-ore concentration is practiced. The identification of oxidized lead-ore minerals and the efficient concentration of a lead ore taken from the oxidized portion of an orebody which has previously yielded poor recoveries mere the objects of a recent investigation. Thus the ore examined was selected from a large orebody. The work was undertaken at the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo.DESCRIPTION OF OREThe ore was of a brownish color owing to oxidation of some of the iron minerals to limonite. The lead content was 6.80 percent, and a cursory examination showed that most of the lead was present as galena. Small amounts of sphalerite, siderite, and pyrite were readily identified. The chief gangue mineral was dolomite, accompanied by smaller amounts of calcite and glauconite."

Jun 1, 1933

Laboratory-Scale Magnetohydrostatic Separator for High Resolution Density Analysis of Plastic and Other Wastes Recycling and reuse of different plastic wastes is still a current problem to solve for process engineers and it is true for seeking industrial applications as well as for smaller laboratory-scale, where a given waste sample, plastic or even metallic, has to be precisely separated into narrow density fractions to gain data for industrial design or for scientific research. The principle of magnetohydrostatic separators are known even there are industrial size machines but our primary aim was the development of a laboratory-scale separator for analysis of particles of densities up to 6 kg/L and sizes up to 8 mm. Main parts of the built experimental equipment are the ferrite core with two high power coils. The shape of the ferrite core at the two sides of the separator channel was specially designed to produce isodynamic magnetic field. In these places the ferrite core was constructed from laser cut ferrite sheets. The development of the high power electric supply for the two coils was a real challenge because the high voltage and current (400 V, 30 A) and because it had to be precisely regulated for being able to set discrete relative forces on the particles. Two separator channels were made from transparent plastic. The magnetic fluid is circulated by a centrifugal pump, fresh feed is supplied by a vibrated feeder and products can be taken by built in samplers. The velocity profile in the separator channel is measured by an ultrasonic Doppler velocity meter. Paper reports about the development and itself of the magnetohydrostatic separator and about some fundamental and applied laboratory experiments with different reference particles and wastes from used cars and electrical appliances.

Sep 13, 2010

By David A. Benjamin

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied prospects, claims, and mineralized sites in a 43,053-acre portion of the 51,262-acre Desatoya Mountains Wilderness Study Area (NV-030-l10) in 1985. The study area, located 50 miles east of Fallon, NV, is underlain by alluvial deposits of Quaternary age and volcanic and volcanic-derived sedimentary rock of Tertiary age. No mines or recent exploration activity were identified within the area studied. The Gold Basin area, located 1/2 mile to the south has produced 982 ounces of gold and 10,086 ounces of silver. The Cold Springs area, located 1/2 mile to the west, has recently been explored for gold-silver. Mineralization at these two areas apparently did not extend into the study area, but future mining at these areas would likely impact it.

Jan 1, 1986

By G. Wozniak, R. Rostanski, H. Pfanz, G. Aschan, E. Sierka

"Industrial wasteland is a typical element of the landscape of all the industrialised regions in Europe. There are many examples from Poland as well as from other European countries that post-industrial sites have been undergone natural colonisation and succession to establish in some cases ecosystems of greater biological diversity than the original ecosystems. The post-industry sites regardless of any reclamation carried out, undergo natural successional processes. The respective biological diversity (number of species, and number of plant assemblages) reflects the micro-variety of the specific habitat. This paper summarizes the results of investigations, which have been carried out since 1989 on coal mine water sedimentation pools in the Upper Silesia Industry Region. The aim of this study is to demonstrate the diversity of spontaneous plant communities recorded on post-industrial waste sites. In the course of the long time fieldwork, plant assemblages representing nine phytosociological groups have been identified."

Jan 1, 2005

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980