Search Documents

By Martin Herrenknecht

Tunnel boring machines continue to develop to take on not only larger and larger diameters but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar has required innovative design approaches. A systems approach has been required to produce tunnelling machines that can not only safely excavate the tunnel but do so in an efficient, cost effective manner that stresses production and labor saving approaches. This paper will review the current design developments and present recent projects where these most recent principles have been applied.

Jan 1, 2008

By J. Eriksson

Slag from stainless steelmaking is known to disintegrate, which is an environmental problem and prevents the cooled slag from being utilized. This disintegration is due to the transformation from the ßto the ? polymorph of di-calcium silicate. The transformation is accompanied by an increase in volume of about 11% and a total disintegration of the slag. AOD slag from stainless steelmaking was re-melted in a laboratory induction furnace, together with olivine and calcinated dolomite, to investigate the prevention of disintegration by increased MgO content of the slag with small changes in CaO to SiO2ratio. The modified slag was examined with X-ray diffraction and scanning electron microscopy. The trials showed that an increased MgO content can change the mineral composition towards formation of more Merwinite and Bredigite, which prevents disintegration of the slag. Keywords: slag, disintegration, di-calcium silicate

Jan 1, 2004

By S. J. Schatzel

Coal mine longwall face ventilation is an important component of the overall mine ventilation system. Increases in the production rate due to higher capacity mining equipment tend to increase methane emission rates from the coal face, which must be diluted by the face ventilation with a minimal opportunity for assistance from additional control equipment (i.e., surface boreholes). Increases in panel length, in some mines approaching 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. Face ventilation can also be affected by communication with the methane-laden gob gas reservoir. Except in a two-entry system, belt air cannot be used to ventilate the face in the US, except in limited cases. This relatively recent requirement has further challenged the mining industry in maintaining adequate longwall face ventilation. To assess the effectiveness of current face ventilation practices, a face monitoring study was combined with a tracer gas test on a longwall face. The study was conducted at a US mine operating in a thick, bituminous coal seam with some self-heating tendencies. Multiple gob gas ventholes were located near the face and produced a small portion of ventilation air in their production flow. Initial results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Increases in methane concentrations in the tailgate entry in the vicinity of the longwall face T-junction appeared to be produced primarily by gas flow from the gob, not from increased emissions from the face. Barometric pressure variations were substantial over the course of the study and varied on a diurnal basis, as is typical of many mining operations. Suggestions are forwarded for reducing longwall face methane concentrations.

Jan 1, 2012

The morphological changes that gold undergoes during transport in gravel-bed rivers are a function of transport distance in particular, as well as bedload material, river gradient and velocity, and bed roughness. Gold size, shape and outline are modified by abrasion, flattening, folding and breakage during transport. The resultant morphological characteristics can be used to predict source types, source location and transport distance, as well as the origin and dispersal patterns of gold in ancient placers where the transport history is unknown.

Jan 1, 1998

By P Landeros, D Benado, J Cornejo, A Pinochet, C Caviedes

In 2005, El Teniente mine began preconditioning the primary rock mass by hydraulic fracturing (HF). The major perceived benefits of this process are a decrease in the magnitude of the expected maximum seismic event and improved cave propagation. In addition, HF has resulted in new information on the propagation pressures of each fracture. Previous studies have attempted to relate propagation pressure to minor principal stress or confining stress.Considering the spatial continuity of propagation pressure and the significant quantity of collected data since the incorporation of the HF technique, minimum requirements for geostatistical modelling have been reached, permitting robust estimates inside the representative volume with acceptable errors (Cornejo, Muñoz and Rojas, 2012; Cornejo and Landeros, 2013). These results are then used to identify zones with higher magnitudes, which are mostly related to more complex geotechnical zones (intrusive and major faults) and caving singularities, making it possible to estimate the spatial extension of these zones.Finally, these results are integrated with other geomechanics aspects to support risk analysis of the mining plan.CITATION:Cornejo, J, Landeros, P, Benado, D, Caviedes, C and Pinochet, A, 2016. Geostatistical modelling of hydraulic fracturing pressures at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Vincent Menard

The purpose of the present work is to demonstrate the removal of manganese from a neutral leach zinc-rich solution ([Zn] =150 g/L) at 80°C by oxidative precipitation using a gas mixture of sulphur dioxide (SO2) and oxygen (O2). In order to determine the optimum conditions for manganese removal, several bench-scale semi-batch experiments were performed, where the effects of ORP and gas mixing were investigated. These tests showed that SO2/O2 is a fast and effective oxidant for removing manganese down to ppm level as long as the appropriate ORP is attained/maintained and gas transfer kinetics are optimized.

Jan 1, 2006

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

Introduction Some people say it is almost impossible to get mining permits in California. Some say the day of the lone mining entrepreneur is past. And some say you cannot make money mining gold where old-timers have already mined it, especially in Tertiary gravels. But a young mining operator and SME member, Tim Callaway, is proving these ideas wrong. Callaway's company, Brush Creek Mining and Development Inc., has the necessary permits for its Gardner's Point gold mine in Sierra County, CA. And, Callaway has secured funds for the 7.7 km'/d (10,000 cypd) Tertiary gravel operation. The company's initial goal is to produce 373 to 466 kg/a (12,000 to 15,000 oz per year) of gold at Gardner's Point mine at a cost of less than $6.43/g ($200 per oz). Feasibility studies are currently being conducted to consider product levels up to the 1555 kg/a (50,000 oz per year) involving additional plants and infrastructure. While exploring for other hard-rock properties, the Brush Creek company already operates the Brush Creek lode gold mine. The mine sits high on a ridge south of Goodyear's Bar, which is located on the North Yuba river. It might be noted that the Brush Creek mine has been the subject of media stories recounting how a mine can operate with sensitivity to the environment. Gardner's Point project In 1983, Callaway negotiated with the Gardners Point Ltd. Partnership for control of the Gardner's Point property. The Partnership had been engaged for three years in securing permits, mapping and drilling, and test mining. The Partnership actually mined about 43.5 dam3 (57,000 cu yd) of gravel, which yielded 25.2 kg (810 oz) of free gold. Later, the Brush Creek company acquired ownership of the property. The company then began its own exploration and development program. As underground development proceeded at the Brush Creek mine, plans matured for a high-volume operation at Gardner's Point. Australian and English investors contacted Callaway. A joint venture was negotiated. The Australian owners became majority participants; the Brush Creek company, a minority participant and the operator. The Australian investors agreed to contribute $3.5 million (60%) to the Brush Creek Joint Ventures. The Brush Creek company will contribute its expertise as well as assets and liabilities valued at $2.3 million (40%). About $2 million has been allocated to the Gardner's Point project. Later, Brush Creek Mining and Development Inc. sold 50.4% of the company's common stock to English investors for $5.4 million. Callaway negotiated this private placement, which permits further exploration of projects being investigated. Geography and history The Gardner's Point mine is located in the northern Sierra Nevada of California, about 9.6 km (6 miles) east of the little town of La Porte in Plumas County. The mine lies high on a ridge above Slate Creek, which divides Plumas and Sierra Counties. La Porte is accessible from the Sacramento area by a winding, paved, two-lane highway. But the mine is reached only by two different unpaved county and Forest Service roads. Both roads include steep grades in and out of the Slate Creek canyon. Mine elevation is about 1.4 km (4600 ft) above sea level. The area is thus threatened by occasional heavy winter snows, though it

Jan 3, 1987

By I. V. Lunkin, E. B. Rakishev, B. R. Rakishev

In mining the method of statistical tests is used by solving of problems, exposing to influence of random factors. Such problems are: rational selection of equipment set; co-ordination in time of different processes; interaction between some processes and kinds of works. Usually it is considered that Monte Carlo method proves its value in the first place in that problems, which allow theoretical-probabilistic description. Analysis of numerical solution of mining-economic problems shows that the method of statistical tests may be used successfully by solving of determinate problems, which are solved usually analytically or by the methods of mathematical programming. We are talking about the problems of optimal use of resources, expedient placing of equipment, effective use of investments, rational planning of stripping and extracting works, groups of mining enterprises and about different variants of transport problem. In the report possibility of the method use is studied at an example of typical technical-economic problems solving. By solving of these problems the variant of the method with uniform distribution of random quantity had been applied and built-in random number generator of visual modelling system VisSim had been used. By algorithms elaboration it seems very perspective to use combination of the Monte Carlo method with traditional methods of numerical solving of the problems (methods of linear, nonlinear and dynamic programming and so on). Keywords: method of statistical tests, mining-technical problems, diapason of random number sample, efficiency function and its extremum.

Jan 1, 2003

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By W. A. Ahrens, J. H. McNamara, J. G. Franek

"An economical, pollution-free process has been developed for the hydrometallurgical extraction of copper from sulphide ores. The extracted copper, in the form of cuprous chloride (CuC/), is converted by reduction to copper metal. The metal is melted and fire -refined into wire bars which meet the standards of electrolytic tough pitch (ETP) copper wirebars. IntroductionThe successful development of the Cyprus Copper Process has been an evolutionary series of events covering a time span of some nine years. The original process, based on an electrolytic membrane cell principle , was abandoned in 1975 because of technical, economic and pollution problems. During the past four years, the pilot plant has been reconstructed based on a new flowsheet and operated successfully in several campaigns, some for as long as four months. The pilot-plant hydro section operates at a 225-lblhr copper rate. In October 1977, a feasibility study was completed by Jacobs Engineering, Pasadena, California. The study showed favourable economic and technical feasibility. Jacob's studies in 1978-79 revealed favourable comparative economics with other known pyrohydro processes and favourable economies of scale.The Cyprus Copper Process converts copper concentrates of varying composition into copper metal, which has been proven to be equivalent in every way to electrolytic tough pitch copper, suitable for electrical applications. This is accomplished at capital and operating costs which are estimated to be lower than those associated with any other known currently applicable technology. Also, the total energy requirement is equal to or less than any other known process and the process is essentially pollution free."

Jan 1, 1980

By A. K. Majumder

Particle motion in fluids is a subject of considerable practical importance to engineers working in fields such as hydraulics, river mechanics, chemical engineering and mineral processing. Many mathematical models have been proposed to predict the terminal settling velocities of particles in a fluid medium. The selection of an appropriate mathematical model has, therefore, become a challenging task for practicing engineers. This paper reports on an attempt to identify some of the useful models found in the literature for predicting particle-settling velocities in a fluid under free- and hindered-settling conditions. From this study, it was concluded that there is no well-accepted model validated by experimental data available for predicting particle hindered-settling velocities in a suspension of polydisperse and polydens particles. Collective efforts should, therefore, be made towards developing a hindered-settling model, as this is an absolute prerequisite for many model structures in mineral processing and other engineering disciplines.

Jan 1, 2007

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 26th August, 1970, at 4.15 p.m. Mr. J. K. E. Douglas (President) was in the Chair. There were also present sixty-three Fellows, thirty-five Members, one Graduate, eight Associates, five Students and nineteen Visitors, making a total of one hundred and thirty-two. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: 'It is my sad duty to announce the deaths of the following members of the Institute. Dr J. A. Papenfus, Fellow, who joined the Institute in 1942 and passed away on the 28th of May, 1970. Mr D. G. Beadle, Fellow, who joined the Institute in 1946 and passed away on the 17th of June, 1970. Gentlemen, Derek Beadle was very well known in this Institute. His papers on dust will be remembered and, at the time of his untimely death, he was one of our assistant editors. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 15th April, 1970, as published in the July, 1970, issue of the Journal'. Agreed. WELCOME TO VISITORS The President: 'Ladies and Gentlemen, we are honoured this afternoon by the presence of many distinguished guests and I extend to you all a most cordial welcome. We are happy to have with us Dr A. A. von Maltitz, President of the Chamber of Mines of South Africa, who is also Honorary President of this Institute. We also have one of our Honorary Vice-Presidents, Mr T. L. Gibbs, the Government Mining Engineer; Mr D. E. Hamm, President, Institution of Certificated Mechanical and Electrical Engineers, S.A.; Mr S. C. M. Naude, Director, Witwatersrand Technical College; Mr I. R. G. Stephen, Senior Vice-President, The S.A. Institute of Electrical Engineers; Mr G. M. Tompkins, President, The S.A. Institution of Mechanical Engineers; Professor P. B. Ackermann, President of the Geological Society of S.A.; Mr A. S. Robinson, Vice-President of the S.A. Institute of Civil Engineers; Professor W. Mare, President of the Institute of Land Surveyors of the Transvaal; Mr B. D. Charlton, President of the S.A. Institute of Assayers and Analysts; Mr R. Hemp, The President, The Mine Ventilation Society of S.A.; Mr L. J. Prince, The President, The S.A. Association of Mine Managers; Mr J. Botha, The President, The S.A. Institute of Foundrymen; Mr G. Niterl, The President, The Institute of Welding; Mr M. R. Gericke, President, S.A. Council of Professional Engineers; Mr N. A. Honnet, Chairman, Orange Free State Branch; Mr P. R. C. Cooke, Chairman. The South African Chemical Institute (S. Tvl. Section). Gentlemen, we are very honoured indeed, to have these distinguished gentlemen with us this afternoon, as our honoured guests. We are also pleased to have with us, one of our Honorary Fellows, Mr F. G. Hill, and several Past-Presidents. I also extend a very warm welcome to all our lady guests and to all our other visitors.' MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Fellows: Herbert Dalton-Brown, Stephen William Morel. Members: Clive Lester Workman-Davies, Basil James Russell Botha. Students: Timothy Nigel Watson, John William Hair-bottle. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade.' ANNUAL REPORTOFTHE COUNCILAND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1970 The President: 'I now have pleasure in presenting to you, the Annual Report and Statement of Accounts for the year ended June, 1970. These have been handed to you this afternoon and, as is customary, I propose they be taken as read. Before moving their adoption, however, I would like to refer to some of the salient features, leaving as is usual, the task of dealing with the finances, to our Honorary Treasurer. It is encouraging that membership has continued to grow, and now stands at 1,613, an increase of 61 over last year's total. Your Council, however, is aware that there are still people in our mining and metallurgical industries, who could qualify for membership, but who have not yet joined the Institute. A drive to increase membership was accordingly organised, and members of Council were given the responsibility for campaigning in sections of industry, and for publicising the objectives and advantages of belonging to the Institute. Up to now there has not been much reaction to this campaign, but I hope we will see results in the coming year. At the same time, Council has recognised the need for change in the conduct of the Institute's affairs in order to meet the changing needs of our membership. Our members, both mining and metallurgical, are in the first place, geographically more widely dispersed than they used to be, and secondly, with the growth of the metallurgical industry, their technical interests are now more diversified. The Institute must cope with these changing needs if we are to continue to perform a useful function. The

By A. D. Dalvi

With the current economic situation, the demand for nickel and other base metals has fallen significantly. More than 440 kt/yr world nickel capacity has been taken out of production within the last year, or more than 25% of the total [1]. This situation is similar to that at the end of 1970?s and it will take a number of years for the demand to recover to the levels before the economic downturn. In the meantime, the challenges facing the industry have increased due to diminishing ore grades, more inaccessible and complex deposits, mounting capital and operating costs and the various external pressures which include socio-economic, environmental, and energy challenges. All industries will be faced with paying the ?total ownership costs? in the future. This will only increase the burden on the industry. How to cope with this in what Thomas Friedman calls the ?Energy-Climate Era? [2] will be the most pressing challenge for the next generation of metallurgists and managers. It will force us to take a broader view of the problems and the solutions beyond mere technical. The metallurgists, engineers and project managers will have to look at the overall projects and their objectives in designing the solutions, requiring a top-down strategic approach.

Jan 1, 2009

By Y. A. Attia, M. Elzeky

Thiobacillus ferrooxidans bacteria were used in this work to study the effect of bacterial adaptation on the bioleaching of three iron-bearing sulfide minerals, namely, pyrite, chalcopyrite and arsenopyrite. The change in the pH during the bioleaching process was observed and the mechanism of the bacterial action were discussed. It was found that bacterial adaptation prior to bioleaching, enhanced the degree of sulfide leaching by 2-4 folds over that of non-adapted bacteria. A1 so the bacterial activity was enhanced by 2-4.8 folds. The pH of leaching solutions was decreased by the increase in both adaptation period and bioleaching time. It was also concluded that the mechanisms of bioleaching of iron-bearing sulfide minerals involved both the direct and indirect bacterial action simultaneously.

Jan 1, 1989

By C. S. Chenga

Sustainable development is currently an extremely relevant concept worldwide, especially in developing countries like South Africa. Mining and metals companies are also directly affected by the sustainable development agenda. The Mining Charter?s requirements as well as new legislation (Mineral and Petroleum Resources Development Act) expect, among others, for mines to support infrastructure and poverty eradication projects in the communities surrounding the mines. The aim of this paper is to, against the background of a qualitative study of mining communities in the North-West Province of South Africa, put forward some critical factors for the sustainability of social development projects in the mining sector.

Jan 1, 2006

By Michael P. Balducci

Urban deep foundation projects contain unique risks that must be recognized by the parties involved. Common pitfalls must be recognized and avoided or addressed through contractual relations and corresponding insurance coverage. By understanding these pitfalls, examining the risk-apportioning clauses and corresponding insurance obligations, may the parties? desires and expectations be met.

Jan 1, 2008

By L. Archambeault

This paper describes preliminary research on the application of Markov Decision Processes (MDP) to Real Option Valuation (ROV) and the optimisation of mine scheduling. The MDP framework is a novel approach to option valuation and scheduling in mining operations. A learning agent is introduced into the valuation process of an open pit, where prices and block ore grades have probabilistic values. The prices are modelled using a mean reverting diffusion process and the block grades using sequential Gaussian simulation. The agent is asked to learn which production parameters should be used in order to maximise the overall value of the project. The introduction of the agent permits a real option approach to mine valuation, such that the value associated with the robustness of a design to uncertainty can be measured. A simulated example is used in which there are ten blocks to be extracted under conditions of grade and price uncertainty. Using policy iteration, an optimal policy is generated and the value of production options is found. The potential financial gains from applying MDPs to mine valuation and optimisation are substantial and warrant further investigation.

Jan 1, 2007

By D Craw

TheSouthern Alps in the South Island of New Zealand are currently rising rapidly as a consequence of continental collision along the Pacific-Australian plate boundary. Rapid uplift has resulted in a major thermal anomaly in the shallow crust beneath the alps. Alpine topography and associated intense precipitation, coupled with the thermal anomaly are responsible for vigorous combined topographic/convective circulation of water through the shallow crust.   Uplift is greatest in a wedge-shaped region between the Alpine Fault and an associated second-order backthrust system, the Main Divide Fault Zone, approximately 20 km to the east. The Main Divide Fault Zone is segmented into NNE and NE striking faults, which are regionally sub-parallel to the Alpine Fault, but dip northwest in the opposite direction. Reverse oblique-slip on the Main Divide Fault is in an easterly direction, with a greater component of strike-slip movement on the NE trending faults. Elevated topography in the Mt Cook region is related to thrusting of a relatively homoclinal sequence of semi-schistose rocks on top of lower-grade greywacke, which controls the position of the Main Divide. Tectonically induced fluid flow resulted in only minor alteration and hydrothermal mineralisation of fault-rocks in Alpine and Main Divide Faults, and localised deposition of quartz and/or carbonate in the immediate hangingwall.   The wedge between the Alpine and Main Divide Faults is segmented by third-order structures north of the Mount Cook region. A series of right-lateral (-085/700S) and left-lateral (-150/600SW) faults, which are synthetic and antithetic to the Alpine Fault, respectively, developed as a conjugate set during uplift. Fluid-flow in the Southern Alps is controlled by these third-order fault/fracture systems. Cu-Au mineralisation, hydrothermal veins, and surface hot spring activity are localised by third-order fault/fractures and appears to be enhanced where conjugates intersect.

Jan 1, 1995

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996