Search Documents

By Carl Belser

This report on tungsten in Ouray, San Juan, and San Miguel Counties, Colo., is one of a series describing results of studies on the tungsten potentialities in Region III, Bureau of Mines. The San Juan tungsten deposits occur in an area of 250 square miles, centering near the common corner of Ouray, San Juan, and San Miguel Counties (fig. 1). Field work supporting these studies was done in May 1954. Bureau of Mines reports prepared from investigations made during World War II and under the Defense Production Act of 1950 were reviewed.

Jan 1, 1956

By R J. Worland, D Bowyer, J L. Mauk

The TerraSpec is a compact field portable mineral analyser that uses non-destructive reflectance spectroscopy for mineral identification. The instrument uses and measures infrared and visible light that is absorbed by certain covalent and molecular bonds (AlOH, FeOH, MgOH, CO32-, OH, H2O and NH4) within the lattice of a mineral at specific wavelengths producing an absorption spectral profile. A variety of minerals can be detected including clays, micas, carbonates, and hydroxides as well as some sulfates and silicates. However, not all minerals are detectable, such as quartz and feldspar. Alteration minerals replacing volcanic rocks have been studied for several epithermal prospects in the lower Waitekauri Valley (Sovereign, Jubilee, Scotia and Jasper Creek) and a geothermal field in the Taupo Volcanic Zone. At the Sovereign, Jubilee, Scotia and Jasper Creek prospects previous XRD investigations determined well developed clay mineral zonation with illite in the west (Sovereign and Jubilee) grading into interstratified illite-smectite (Scotia) and smectite (Jasper Creek) to the east. Although the percent of illite within interstratified illite-smectite could not be determined and some illite-rich illite-smectite (>90 per cent illite) and some smectite-rich illite-smectite (>90 per cent smectite) could be misidentified as illite or smectite respectively, the TerraSpec survey determined the same zonation of illite to illite-smectite and smectite. Common chlorite, rare calcite and local kaolinite were also detected. At the geothermal field, the TerraSpec was primarily used to determine the occurrence of kaolinite, dickite and alunite, which form in acid conditions. Widely spaced (every 50 to 100 m) XRD results are in excellent agreement with closely spaced (every 5 to 10 m) TerraSpec results that further determined the occurrence of these minerals in previously unrecognised intervals. It also determined the occurrence of zoned smectite, illite-smectite, illite, and chlorite alteration. Overall, the TerraSpec is a rapid mineral identification technique that is very useful in delineating the occurrence and distribution of certain minerals in both epithermal deposits and geothermal fields. Although the TerraSpec cannot detect as many minerals as XRD, the TerraSpec allows data collection at a sampling scale and speed (real time) that is not practical by XRD.

Jan 1, 2006

By Nihal Bohra

A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads. The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles.

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By Axel Sahlin

Jan 1, 1898

By Kourosh Shahriar

The occurrence of rock falls in underground coal mines entails detrimental effects as fatal or non-fatal injuries on workers, stoppages in mining operations and breakdown of equipment. In this paper, a risk assessment approach on the basis of a decision analysis trend is employed in order to assess the possibility of and manage roof falls. Risk is then assessed by determination of likelihood of occurrence and the cost of consequences (outcomes). In this regard, collected real roof fall data from Tabas and Kerman coal regions comprising of several underground coal mines are used. It is concluded that the annual accidents due to the roof falls occurrence in the all investigated mines are so high that it is economically feasible to improve the support systems and to implement a suitable educational program as well as an accurate supervision and other elements of safety management.

Jan 1, 2009

By C A. Locke, A B. Christie, J Cassidy, J L. Mauk

New and existing gravity and aeromagnetic data are used to determine the structure of the Waihi region and to investigate any relationship between structure, hydrothermal alteration and epithermal mineralisation. The 24 mGal, 10 km diameter, negative Bouguer gravity anomaly which occurs south of Waihi has been modelled as a I.5 km deep asymmetrical basin. This basin, the Waihi Depression, is interpreted to be infilled with low-density volcanic rocks of the Uretara Formation and Whitianga Group, overlying older andesites of the Waipupu Formation. To the north and west, the margins of the depression are defined by the Waihi and Mangakino Faults, which have been modelled with dips of 45 - 60¦ to the south and west respectively. The southern and eastern boundaries of the Waihi Depression are defined by smooth, shallow dipping (15 - 20¦) boundaries. The Waihi Depression is interpreted as a fault-angle depression, resulting from southeast extension in the early Pliocene. The Waihi Fault is modelled as an approximately E-W feature, located to the south of Waihi. Small 2 - 4 mGal positive Bouguer gravity anomalies occur north and west of the margins of the depression, and correlate with known areas of hydrothermal alteration and areas of low magnetic gradient.

Jan 1, 2003

Adsorption of Starch on Kaolinite Surfaces

Sep 13, 2010

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By N. A. Barcza

This publication records the proceedings of the Tenth International Ferroalloys Congress, INFACON X, and the third INFACON hosted in South Africa. The Proceedings of the previous two South African congresses in 1974 and 1992 serve, as this volume does, as a valuable record of the papers presented at these important events. This publication comes at a time in South Africa?s democratic development where the theme ?Transformation Through Technology? is very appropriate. The ferroalloy industry has played an increasingly significant role in transformation and black economic empowerment in South Africa, particularly through the advancement and sharing of technology. INFACON X plays an important role in this process, and the stakeholders and organisers of this Congress are thankful for the opportunity to hold this event at this time of transformation in our country. The world of ferroalloys, as well as that of the steel and stainless steel industries, has continued to change rapidly. Recent innovations, better use of resources, increased awareness of environmental issues and ongoing efforts to improve occupational health and safety are among the topics addressed at INFACON X and in these Proceedings. The theme of ?Transformation Through Technology? has been chosen to reflect the regional and global developments in the ferroalloy industry, and the crucial role that technology plays. The Proceedings of INFACON X, the first Congress in Southern Africa of the new millenium, represent a milestone in the technical developments in this major global industry. It contains almost eighty papers in twenty Sessions, from authors in twenty countries, covering raw materials, reductants, energy, electrodes, refractories, furnace design, post taphole services, modelling, simulation, control, sensors, fundamental issues and the applications of ferroalloys as related topics. The major ferroalloys, namely ferrochromium and ferromanganese, are covered extensively in many interesting papers. This comes as no surprise, since South Africa is the leading producer of ferrochromium and also plays a major role in the supply of manganese ore and alloys. Papers on ferronickel, silicon and ferrosilicon ensure that all the large-volume ferroalloys are addressed. These Proceedings of refereed papers of high quality will serve the ferroalloy industry for many years to come, as has been the case with previous INFACON events. For the first time in the history of INFACON, the Proceedings will be available both in bound and in a searchable electronic CD-ROM format. We appreciate the time and effort that the authors and referees have devoted to making this publication a really valuable document. Their contributions are recorded for posterity and reflect the advancements they and their colleagues have made to benefit the ferroalloy industry. Without these ongoing improvements, the industry would stagnate and not fulfil its role in the advancement of mankind. All papers included in these Proceedings were peer-reviewed by at least two referees. About 130 referees were sourced internationally to fulfill this function, and their valuable technical and editing inputs are gratefully acknowledged. Finally, I would like to thank the Technical Programme and Publication committees, led by Dr. Lloyd Nelson and Dr. Noël Machingawuta respectively. Without the tireless efforts of these individuals and their Committee members, the technical programme and these Proceedings would not have been the success they certainly are.

Jan 1, 2004

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

By K. Oraee

Mining of copper ore and the related industries play an important role in Iran?s economy. Copper ore production in Iran accounts for 75% of the total production in the Middle East. All activities related to copper, that is, exploration, production, refinement etc are owned and managed by state owned companies. Decisions have been made to privatize all these activities. To assess the success of this privatization process, different components of the industry must be subject to economic analysis. In this paper, the cost estimation of all operations has been carried out. The total potential and attainable revenues have also been estimated using historical data available from the industry. Risk is a major factor in all mining activities and the copper industry of Iran has been subject to risk factors arising from many internal and external variables. These variables have been recognized and their effects evaluated. The effect of risk on the economic feasibility of the operations in the industry has also been analyzed.

Jan 1, 2011

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009

By H. M. Lawrence

"Florida, the State that supplied 82 per cent of the phosphate rock sold in the United. States in 19284, has two producing areas - the hard-rock and the land pebble districts. Production of the hard-rock field, decreasing importance in recent years, is now confined to mines near Dunnellon, in Marion and. Citrus Counties. The land-pebble district, with a production of almost 80 per coat of the nation's requirements, is located, in Polk and Hillsborough Counties. In the land-pebble area the phosphate deposits - probably Pliocene in age, derived by marine action from underlying, older, phosphate-bearing formations - consist of beds of phosphate matrix, covered by practically barren sands and clays. The overburden, ranging in thickness up to 45 feet, is removed by hydraulic methods or by drag-line excavators. The matrix, ordinarily less than 25 feet in thickness, is mined by hydraulicking and is pumped to adjacent washing plants for beneficiation. The dried product of the washing plants is the Florida pebble rock that is sold in foreign as well as domestic markets.The beneficiation of phosphate ores in the land-pebble district of Florida has been largely limited in the past to the recovery of the coarser pebbles. By washing and screening the crude matrix a separation is effected at about 20 mesh (0.033 inch). The coarser material is the phosphate-rock product of the plant and the finer material is discarded. The amenability of the washer- rejects to treatment by other processes is being investigated. Of methods that may have some application to the treatment of the low-grade phosphatic sands that comprise the greater portion of the washer-rejects, gravity concentration has received some study.Laboratory experiments to determine the amenability of phosphate sands to gravity methods of concentration were first performed in October, 1927. Later, in the winter of 1928-1929, a further series of teats was made,. In these later tests phosphatic sands were concentrated by hydraulic classification, and. also by hydraulic classification followed by tabling. In these experiments concentrates with an analysis above the minimum grade of commercial phosphate rock (66 per cent bone phosphate of lime - B.P.L.) obtained. The recovery of the phosphate varied but was promising enough to warrant further study. A more comprehensive investigation was therefore outlined. This paper presents the results obtained from an investigation, of classification and tabling of phosphatic sands recently completed by the United States Bureau of Mines Su cooperation with certain Florida phosphate companies, the Missouri School of Mines and Metallurgy, and the University of Alabama."

Jul 1, 1930

By M. M. Wong

The Bureau of Mines, under a cooperative research program with four lead companies, has investigated a nonsmelting process for the production of lead metal. The process, which would eliminate sulfur dioxide generation and minimize particulate lead emissions, involves ferric chloride leaching of galena concentrate to produce lead chloride, followed by molten-salt electrolysis of the lead chloride to yield lead metal and chlorine. This chlorine is used to regenerate ferric chloride in the leaching solution. The process was tested in an experimental unit with a capacity of 500 lb of lead metal per day. The tests were performed in three 10-day and six 5-day campaigns, during a period spanning 28 mo. The study was carried out using a southeastern Missouri lead concentrate. Typical lead recovery was about 98 pct. Process problems related to impurity buildup and control were studied. When copper and silver impurities were removed from the leaching solution, a lead metal purity of 99.999 pct was obtained. Lead-in-air levels and lead-in-blood levels of operating personnel were monitored. The process has potential for producing lead with minimum pollution, but is not ready for commercial utilization. Operation of a prototype commercial electrolytic cell and a full-scale pilot-plant investigation by industry are needed to evaluate the commercial viability of the process.

Jan 1, 1983

By J. D. Steenkamp

Southern Africa has a history rich in the pyrometallurgical processing of ores. Two of the alloys produced are high-carbon ferromanganese (74?83 per cent Mn) and silicomanganese (59?67 per cent Mn and 14?31 per cent Si). The largest land-based manganese ore deposit in the world is based in the Northern Cape Province of South Africa. In 2010, 6.3 Mt of ore from the deposit was exported, mainly to China, Norway, Japan, and India, and an estimated 1.1 Mt beneficiated locally to produce manganese ferroalloys. In southern Africa the producers of manganese ferroalloys are Metalloys and Assmang, and of silicomanganese Transalloys, Mogale Alloys, and Match Corporation. Submerged arc furnace technology is utilized in the production of high-carbon ferromanganese (HCFeMn) and silicomanganese, applying the discard slag practice in both instances. The carbon content of HCFeMn is reduced using converter technology and that of SiMn using the Perrin process. Ninety per cent of the world?s manganese ferroalloys production is consumed by the steel industry. The consumption (and production) of manganese ferroalloys therefore closely follows worldwide steel production. From 2001 to 2010, the doubling of the worldwide production of manganese ferroalloys can be attributed to an increase in production capacity in Asia and Oceania, with the largest increase in the production of SiMn. Manganese ferroalloys produced in Asia and Oceania are mainly for the local market, with North America, Europe, Russia, and Turkey the major markets for alloys from southern Africa. The major challenges faced by the southern African manganese ferroalloy producers are increasing electricity tariffs and productivity of labour, which require a concerted effort by all parties involved to achieve a satisfactory solution. Keywords manganese ferroalloys, ferromanganese, silicomanganese, southern Africa, South Africa, manganese ore, high-carbon ferromanganese, refined ferromanganese, refined silicomanganese.

Aug 1, 2013

By M. S. Delibalta, S. Kahraman, R. Comakli

The block cutting machine is one of the most important noise sources in the stone processing factories. In this study, the assessability of the noise from the block cutting machines in the stone processing factories using the P-wave velocity was investigated. The noise levels of some block cutting machines were firstly measured during the cutting of the three different rocks. Then, core samples of the same rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. A conversion factor was obtained by dividing the site noise levels by the laboratory noise levels. Then, thirty seven different rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. The P-wave velocity of rock samples were also measured in the laboratory. A strong relation between the laboratory noise levels and the P-wave velocity was found. The noise level from the block cutting machines can be assessed using the derived relation and the conversion factor.

Jan 1, 2011

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966