Search Documents

By Radford B. Langston, John A. Marjerison, Graham C. Howell, Hendrik A. D. Kirsten

Probabilistic design is gaining wider acceptance in the rock engineering community since it allows more rigorous determination of risk relating to ground fall or excavation instability. Risk analysis can be conducted by various means, but the basis is formed by either objectively or subjectively determining probability of occurrence of an event. In the case of rock engineering, this event is either instability or excavation failure. Rock mass classification systems provide objective analysis of data collected on a typically subjective basis that also relate closely to excavation stability. A probabilistic analysis technique is presented that uses statistical distributions of rock mass and material properties, ground support fixture specifications, stress conditions, opening geometry, and ground support installation quality to more rigorously determine probability of failure for an underground opening and the subsequent risk to personnel.

Jan 5, 2007

By J. W. Langford

A more effective method of fracturing and chipping the formation is necessary to significantly increase the productivity of blasthole drilling with a roller cone bit. The conventional rotary blasthole bit engages the formation and initiates spalls, chipping and fractures in the formation at a rate dependent on the amount of pull down force applied by the drill. The rotary speed of the drill increases the number of fractures and creates drilled chips that are removed from the hole by the air circulation. An engineering project was motivated to develop a low pressure, low impact downhole percussion hammer to provide an overstrike force to a blasthole bit, in addition to the conventional pull down force and rotary speed. The objective of the project was to utilize existing rig air packages in the range of 50-110 psig and provide an overstrike force to the bit in the range of 1100-1500 impacts per minute. Laboratory testing performed on Barre granite achieved, on average, a 40% improvement in rate of penetration. This performance has been confirmed in actual blasthole drilling in copper and iron ores mines. During the testing phase, additional unexpected benefits have also been realized.

Jan 1, 2011

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM The technique reported here involves measuring the air pressures generated within sealed boreholes located behind blasts. Results from twelve free face blasts in competent rock environments a represented. There were no instances of high pressure gas penetration, even at distances corresponding to less than one blast burden. Rapidly generated underpressures were measured in most holes, with the magnitudes of the peak pressures decreasing with distance behind the blasts. It has been proposed that the under pressures are the result of new volume created due to crack formation and overall rock mass dilation. The experimental evidence is consistent with this, including a correspondence of the onset times of the peak underpressures with the nominal firing times of the nearest blastholes. New post-blast cracks were observed when using borehole video cameras in the monitoring holes. A calculation of new volume produced within the monitoring holes is proposed as an indicator of damage. While the data exhibit considerable scatter, there is a power function dependence on scaled distance, which resembles that of typical vibration data. The data also lie within the normally quoted vibration regimes for rock damage and are consistent with measured extents of damage. It is concluded that this technique may provide an inexpensive and practical comparative measure of near-field rock damage due to blasting. It is further concluded that gas penetration is not a common phenomenon. Damage appears to be mainly attributable to the nearest blastholes and the control of charge mass in perimeter blastholes is emphasized for damage minimization.

Jan 1, 2000

As a minerals company, obtaining the appropriate consents under the Resource Management Act 1991 and getting permits granted for exploring, prospecting and mining under the Crown Minerals Act 1991, is necessary for actively exploring and mining in New Zealand. But the essential mix of ingredients for a viable and healthy Industry go way beyond this.   In the short term, an individual company seeking to operate on or within the Crown minerals estate of New Zealand must chart a course through the requirements raised by new cornerstone legislation, the Resource Management Act, the Crown Minerals Act and, the Conservation Act 1978 (where the minerals sought coincide with this estate).   However, this paper suggests that in the longer term for individual operators within the Industry and for the Industry at large to remain viable and sustainable and for New Zealanders to continue to enjoy its benefits, much more is required. Not least of which is a better balancing of competing uses and attitudes, which will require an opening of minds, a change in mindset, topped off with those two most essential of ingredients advocacy and leadership.   New Zealand has undergone massive restructuring in the last 15 years. Is it complete? Have each of its fronts evolved to the end point which was envisaged by the designers of the regime? What are the advantages? What is left to be done? What are the impediments from an incomplete transition which are left to either dog the Industry or remain as a challenge to be removed to ensure the Industry's smooth sailing into a prosperous and environmentally clean and friendly future? A future wherein an educated and understanding public welcome and are proud of the Minerals Industry to whom they owe the standard of living which they enjoy.   This presentation will examine the role of the New Zealand Minerals Industry Association (NZMIA) in paving the way for an optimum operating environment in which to couch a healthy industry into the future.

Jan 1, 1997

The Century zinc-lead-silver deposit has a geological resource of 118 million tonnes averaging 10.2% zinc, 1.5% lead and 36 g/t silver. It lies approximately 250 krn NNW of Mt Isa in NW Queensland, Australia, and is hosted by middle Proterozoic age siltstones and shales of the Lawn Hill Formation. Within the orebody, most mineralisation occurs selectively within black shale units as fine grained sphalerite and galena lamellae with minor pyrite and siderite. The black shale units are separated by weakly mineralised sideritic siltstone horizons. The deposit is unmetamorphosed and only weakly deformed, displaying excellent lateral stratigraphic and grade continuity. The deposit is mostly overlain by younger Proterozoic sediments and later Cambrian age limestone cover and only a small proportion of the mineralisation crops out. Mineralisation has a subtle surface expression without a classic gossan profile, probably due to the low iron sulphide content of the ore. These factors contributed materially to the length of time between the first recognition of lead-zinc-silver mineralisation in the area by prospectors in the 1880s, to the discovery of the orebody by CRA Exploration Pty Ltd (CRAE) in April 1990.   Small scale prospecting and mining continued in the area from the date of the first mining lease in 1887. Post 1950, the deposit area was also included within nine separate regional exploration titles prior to CRAE's title acquisition in 1987. CRAE's original exploration strategy was partly pragmatically and partly conceptually inspired, but the eventual discovery only partly conformed to the original conceptual model. The deposit was found higher in the stratigraphy than the original target position, with unexpectedly low total sulphide content relative to other known deposits.   The discovery soil anomaly was located by the CRAE's first regional orientation traverse line in the area, but was not drill tested for three years. The discovery sequence at Century has strong elements of persistence, technical competence and some luck. It demonstrates that even in well explored terrains (by conventional standards) the exploration story can never be said to be over. The foreshadowed development of an economic resource at Century will hopefully inspire continued commitment to 'brownfields' exploration by mining companies, and demonstrate to external regulators the importance of genuine multiple land use strategies and the need for continued access to land for exploration and mining purposes.

Jan 1, 1995

By Italo Oñederra

A review of breakage and fragmentation literature has shown that only a few models have been specifically developed for applications in underground production blasting. These approaches, however, have applied empirical relations that do not adequately consider ring blasting geometries, have failed to appropriately respond to changes in basic design input parameters, and have complex input and calibration requirements. This justified the development of an alternative modelling framework to specifically address the prediction of fragmentation in underground production blasting. In this sense, the new model, designated as “FRAGMENTO”, is introduced in this paper. The basis of FRAGMENTO is a “single ring” deterministic model which can be extended into a stochastic model to simulate the impact of external operational factors on fragmentation. The single-ring component mechanistically models the extent of both near field and mid to far field fracture zones to predict the distribution of rock fragments expected to report to drawpoints. In this paper the response of this key component is evaluated and its practical application demonstrated with the introduction of a methodology to infer critical burden conditions.

Sep 12, 2005

Pyrite Bioleaching and Slag Neutralisation - Two Treatments in a Single Process for Recovering Valuable Metals from Both Materials Very often the production of copper sulfide concentrate yields pyrite concentrate as a by-product. This is the case at the Knre mine in northern Turkey. This kind of concentrate may contain low grades of valuable non-ferrous metals. Bioleaching of such pyrite concentrates is a processing technique to solubilise metals like copper, zinc or cobalt in a sulfuric acid pregnant solution. The pyrometallurgical processing of copper sulfide concentrate produces slag that still contains valuable metals in varying concentrations. Slag is used in many ways: as aggregates, ballast, pavement material, in cement production and glass making. Due to its relatively alkaline nature, it can also be used to neutralise acidic solutions. A preliminary study of the bioleaching of the pyrite concentrate (Co 0.28 per cent, Cu 0.56 per cent and sulfur as sulfide 42.6 per cent) produced at Knre has been undertaken with the assessment of the neutralisation of the acidic bioleach solution by using old slag (Co 0.29 per cent, Cu 1.70 per cent and sulfur as sulfide 0.89 per cent) stockpiled on the site. The main conclusions of the study were as follows: Knre pyrite was amenable to bioleaching at 40¦C. Cobalt solubilisation directly related to pyrite degradation reached a maximum yield above 90 per cent. Final copper recovery was limited to approximately 66 per cent not directly related to bacterial growth and pyrite oxidation. Slag could be used as a substitute for limestone as a neutralising agent in the bioleaching tanks. Cobalt and copper could be recovered from pyrite concentrate and slag simultaneously from both materials. A pre-feasibility study is underway to carry out a preliminary cost estimate of an installation for cobalt and copper production from these two materials processed in a single operation.

Sep 13, 2010

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.4/ The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; and 1960, 5.5 feet.5/ Table 1 includes data on number and production of bituminous coal and lignite mines classified by I-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, and 1960. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness -less than 2 feet to more than 50 feet - a large majority of the production, 62 percent in 1960, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1962

By Mats Keisu, Bengt Niklasson

The Sofia project has increased the level of knowledge and technique within tunnelling, drifting and contour blasting.

Jan 1, 1992

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

By J. Darlington, A. K. SenGupta

Water-swellable layered silicates, namely, the smectite clays can remove suspended materials (called herein as debris) and metal ions from aqueous streams. The present study shows that the flocculating and metal extracting abilities of smectite clay-based flocculants can be enhanced when these clays are used in conjunction with a specific anionic polymer. Such performance enhancement is attributed to the following: i) the clay-dispersing ability of the polymeric additive, that would translate into an increase in the clay-surface area available for the attachment of the debris particles onto the clay particles; ii) the possibility of dispersant-to-coagulant transition of the polymer during the later instants of the treatment process, as a result of reduction in solvency of the wastewater for the polymer due to the release of cationic species from the clay-based flocculant solids; iii) metal-complexing ability and adsorption properties of the polymer.

Jan 1, 2002

By D. N. Ferguson

The separation of certain minerals by electrostatic techniques can be difficult due to their similar electrical conductivity, and any technique to improve this can be useful in certain difficult separation applications. Triboelectric differences between mineral scan result in certain minerals acquiring small positive or negative charges prior to inductive electrostatic separation. By changing the polarity of inductive separation, relative changes in mineral recovery can be observed, which may be beneficial. In this brief study a JKTech mineral liberation analyser (MLA) was used to evaluate the effect of polarity change on selected minerals present in the Richards Bay Minerals deposit, and an approximate triboelectric series based on this behaviour is presented.

Jan 1, 2010

By W. C. Babcock

This report covers Phase V of .a continuing program to apply a new liquid membrane process called coupled transport to the recovery pf metals from hydrometallurgical leach solutions. During this phase of the program, a membrane system of moderate scale was constructed and field-tested at the Exxon Highlands Mine and Mill Co. site near Douglas, Wyoming. The test unit contained four hollow-fiber membrane modules, each with 100 ft2 of membrane area. In the field tests, about 1000 gallons per day of leach solution was processed. The unit was operated on the leach solution for about 50 days. Leach solution entering the unit contained 100 ppm uranium. This concentration was reduced to about 5 ppm by coupled-transport treatment, and the uranium was concentrated to about 2 wt% as a uranyl carbonate product. Under these conditions, a transmembrane uranium flux of about 2.5 lb/ft2-year was obtained. An economic analysis showed that the cost of recovering uranium from this leach solution via coupled trans-port is about $1.20/lb. At higher concentrations of uranium in the leach solution this cost is reduced. For example, at 1000 ppm the cost of uranium recovery is about $0.30/lb.

Jan 1, 1983

By P. J. Doig

The LCLS project at SLAC will allow new insights into material properties, chemical reactions and biological processes. The project includes half a mile of new underground construction. Excavation in weathered rock is by NATM, using AM 50 roadheaders. Construction began in 2006 and is expected to be completed in 2008. This paper details the construction of the tunnels and cavern on the project.

Jan 1, 2008

By Ch. D. Taylor

Past studies with blowing face ventilation systems have shown that using a machine-mounted scrubber and water sprays can reduced methane levels at the face. The current research was conducted to determine how the sprays and scrubber interact to reduce methane levels, and what spray configurations provide the best face ventilation when used with a scrubber. Testing was conducted in a ventilation test gallery designed to simulate a full-scale mine entry. In the entry, a model mining machine, equipped with a simulated dust scrubber and water spray systems, was located at the face of a 6.1 m (20 ft) box cut. Face ventilation was provided by a blowing curtain located 12.2 m (40 ft) from the face. Methane released from a manifold at the face was measured at six locations near the face to compare the ventilation effectiveness of the spray systems while operating with and without the scrubber. Airflow movement across the face was affected by the spray configuration and scrubber operation. Average face concentrations were lowest when directed sprays were used with the scrubber. Varying the direction of the scrubber exhaust affected face methane levels.

By Andrew Kaczmarek

The mining industry is enjoying a much needed and long awaited increase in demand for natural resources. However, consolidations in the mining and mining service industries, along with a generational departure of experienced industry professionals, is challenging today’s mining companies. These challenges are not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies. They oftentimes lack for operating properties to draw experienced professionals from. Also, juniors have to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This article discusses some strategies developed by Anatolia Minerals Development (Anatolia) in developing its Çöpler gold project in central Turkey.

Jan 1, 2006

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner's performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983

This paper evaluates the effect of longwall mining on a cluster of unconventional shale gas wells located in a district barrier pillar between a current longwall panel and the future panel north of the barrier pillar. A cluster of 19 unconventional shale gas wells have been drilled and 5 additional gas wells have been proposed in the barrier pillar. The closest gas well is 25.6 m (84 ft) to the current panel tailgate and 26.2 m (86 ft) to the tailgate of the future panel north of the barrier pillar. The rib-to-rib width of the barrier pillar is 57.9 m (190 ft). The distance between the two gas wells across the barrier pillar is 6.1 m (20 ft). The pillars in the current tailgate are on 22.9-m (75-ft) and 32.0-m (105-ft) centers, and the pillars in the tailgate of the panel north of the barrier will be on 22.9-m (75- ft) and 36.6-m (120-ft) centers. The two longwall panels adjacent to the barrier pillar are 475.5-m (1,560-ft) wide. The overburden depth at the shale gas well site is 321.6 m (1,055 ft). The wells have been installed in the barrier pillar, and the current district panel and subsequently the panel north of the barrier will be developed and retreated in the near future. The average min

Jan 7, 2020

By H Firdausi, I Pasek, T Chenier

The Grasberg Block Cave (GBC) Mine is one of the future underground mines of PT Freeport Indonesia (PTFI). Located in the remote highlands of Papua, Indonesia, the GBC mine is scheduled to start production in 2017 reaching its peak production capacity of 160 000 t/d in 2023.In order to reach planned production capacity, the GBC mine will utilise an ore handling system consisting of rail haulage, crushing and conveying. The rail haulage system will utilise over 20 km of track while crushing is accomplished by way of three gyratory crushers each with a capacity of 3300 t/h. Nine conveyors operating in two parallel systems, each system over 3 km in length, will move the ore from the crushers to the stockpiles. These systems require a network of larger tunnels and mass excavations to accommodate the planned production facilities.This paper will describe the ore handling system, tunnel and mass excavation methodology as well as some of the challenges encountered with ground conditions and excavation quality during the execution of the project. A combination of lateral and vertical development methodologies and equipment, including drill jumbos, mechanised raise climbers and specialised ground support equipment, have proven successful in the development of a quality ore handling system.CITATION:Pasek, I, Firdausi, H and Chenier, T, 2016. Development of the ore handling system at the Grasberg block cave mine, Indonesia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016