Search Documents

By Fumihiko Sumiya, Hideki Hamashima, Shigeru Itoh, Shinya Tanaka

The detonation characteristics of non-ideal explosives, especially the emulsion explosives, are critically affected by the confinement of case. In this study, we focused the shock wave propagating in case as confinement factor. Therefore, the objective of this study was to obtain a better understanding of the influence of shock wave propagating in case on the detonation characteristics of explosives in laboratory scale.

Jan 1, 2007

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

The Upper Waimangaroa mining permit is part of the Buller Coalfield and lies on the eastern side of the Stockton-Denniston Plateau. The mining permit area is estimated to contain a total in-ground coal resource of 58 million tonnes, contained within 13 separate coal resource .blocks. The coal is Bituminous High Volatile B rank with export potential as semi soft coking or thermal coal. The Northern Opencast mine is the first mine proposed for Upper Waimangaroa and consists of the three resource blocks at the northern end of the permit area. The highwall of the mine will cut into the Mt William Range resulting in overburden cover of up to 150 metres in some areas. The ability to rehabilitate the area after mining was a major consideration in the design of the mine. The Northern Opencast area has been geologically mapped, extensively drilled and effectively modelled using Vulcan software. Three distinct coal seams are present and the mineable in situ resource is estimated at 8.7 million tonnes of which approximately 7.1 million tonnes is likely to be recoverable. It is proposed that this resource will be mined using opencast methods and the void will be backfilled with overburden. The life of the mine is at this stage estimated at 19 years based on an annual production of 500,000 tonnes at 1.8% sulphur and the Upper Waimangaroacoal will be blended with low sulphur coal from the Greymouth Coalfield to meet export specifications. The Northern Opencast area contains a range of native flora and fauna and physical features which make it an environmentally significant area. Mining will totally modify the area, thus an effective rehabilitation scheme is an integral part of the mine plan. Various rehabilitation methods will be used, and wherever possible, the backfilled areas will be rehabilitated so as to resemble the original area as closely as possible.

Jan 1, 1998

Economic Sustainable Power for Mineral Processing

Sep 13, 2010

The evolution of surface mine layout configuration is a function of the schedules and sequence of material excavation within the optimized layouts. The production schedules and sequence of materials movement from multi-bench and multi-face operations are difficult to plan and execute. However, the ability to maximize the profit or net present value of an orebody is largely dependent on the mining schedule. The mining schedule will determine the life of the mine, the projected cashflows, and the investment requirements over the mine life. The pit geometries, pit expansion rates and the periodic volume of materials from different benches in a multi-bench, multi-face open pit mine determine the equipment requirements. The volume of materials excavated, as well as pit layout changes from circular and elliptical geometries of an oil sands mine were modeled using analytical geometric and parabolic partial differential equations (PDEs) and solved within Matlab. The results show that the geometric values are almost the same as those obtained from PDEs for different pit configurations. The economic analysis shows that both the current mining system (CMS) and the cyclic excavator conveyor belt control system (CycEx CBCS) are viable with high NPV (= $3.20 × 1010), PI (> 19%) and IRR (> 29.02%) with short discounted payback periods (= 3.24 months). The CycEx CBCS option is more economic than the CMS option. Its NPV is 1.27 times that of the CMS option. The PI and IRR for the CycEx CBCS option are respectively 2.24 and 1.13 times that of the CMS option. As well, the CycEx CBCS option has almost half the DPBP of the CMS option. The CMS option has an operating cost of $1.386 per tonne ($2.774/barrel) while that of the CycEx CBCS option is $0.779/tonne ($1.558/barrel). These results show that the CycEx CBCS option is the better option for mining companies working on oil sands deposits to invest in.

Jan 1, 2011

By Robert B. Hopler

Explosives, originally used only in fireworks and warfare, became legitimate contributors to human progress when miners in Eastern Europe began using them to break rock in the early 1600%. Since that time these powerful materials have had a dual role in the world: as agents of destruction in war, and as irreplaceable tools necessary to advance civilization. In the latter role, they serve as agents to enable mankind to produce metals, build roads, and drive tunnels. In other words, to provide those materials, services, and infrastructure without which the modern world could not exist.

Jan 1, 1997

By A. More, J. Bullón

Metal casting is one of the most important operations in ferroalloys factories. After the tapping of the furnace and the depuration of the metal, the preparation for customers with cooling, crushing and sizing begins. In total production costs, this contains around 8 % of the total cost of the metal, depending on the value of the fines and other important parameters. From an investment point of view, this represents around 20% of the total capital for a new furnace. Casting onto a water-refrigerated copper plate is not new for molten metals. In steel, continuous casting machines are normal in every factory. Water granulation casting exists at some ferroalloys plants. However, the majority of plants and production technology still use the technology of lumping, crushing and sizing. This technology is time consuming, produces fines and requires a relatively large work force. In 2001, Ferroatlantica put into operation a new water-cooled copper casting-machine, which seems to be a very convenient solution to solve all these problems. It is in operation at a silicon factory; the same place where the new ELSA electrode was developed for silicon metal production. This paper describes our experiences using it.

Jan 1, 2004

By William C. Geitz

"Lightning has always posed a serious threat to blasting operations, especially wkhin the mining and construction industries and operations involving the manufacture, transport, storage and handling of explosives. In recent years, technological advancements in communications systems and microprocessors have significantiy improved the accuracy and efflliency of lightning detection and warning instrumentation. These advancements have increased the availabilii of highly reliable,accurate and affordable systems for use within the explosives arena."

Jan 1, 1991

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07', the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By Z. T. Bieniawski, Benjamín Celada

After emphasizing the importance of quantitative rock mass classifications in mining, originally directed to selection of rock support measures, but subsequently to estimates of rock mass properties such as rock mass strength and rock mass modulus of deformation, current attention calls for a classification specifically for rock mass excavability by tunnel boring machines (TBMs), which are used extensively in tunneling as well as in the mining industry. This paper introduces the Rock Mass Excavability (RME) index for predicting excavability of rock masses by TBMs using a quantification of machine performance and rock mass conditions. The RME index is based on five input parameters aimed at relating rock mass behavior and machine characteristics: (1) uniaxial compressive strength of the rock material, (2) drillability/abrasivity, (3) rock mass jointing at mine drift face, (4) standup time of the excavation, and (5) groundwater inflow. Development of the RME index entailed the collection of extensive data from more than 28 km of tunnels and some 400 case records from projects in Spain involving double-shield TBMs. In the process, a number of statistical correlations have been established between RME and such output parameters as degree of machine utilization, advance and penetration rates, thrust and torque of the cutterhead, and the specific energy of excavation. It was found that the RME index provides a particularly significant correlation for predicting the average rate of advance (m/day). In essence, the RME index is a classification system that features interaction of rock mass conditions with boring machine characteristics for use in the early stages of a project. It should be noted that the RME index does not replace the Rock Mass Rating (RMR) or Q-systems as used in mining and tunneling; indeed, one of the RME input parameters, standup time, is determined from the RMR. However, the approach presented introduces a specialized tool relevant to excavating tunnels and drifts. Possible applications to hard-rock mining are explored.

Jan 5, 2007

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.Low-sulfidation epithermal gold mineralisation at Ridge Mountain occurs within the Oligocene to Miocene volcanic rocks comprising andesite, porphyritic dacite and diatreme breccia. A diatreme breccia complex with a NE–SW elongated orientation covers an area of 3.0 × 1.7 km. Four main stages of mineralisation were identified, comprising: E–W- to NW–SE-trending quartz-chalcedony veins with disseminated pyrite, chalcopyrite and gold. N–S- to NNE–SSW-trending breccia veins with quartz matrix and disseminated pyrite and accessory sphalerite, galena, chalcopyrite and gold. NE–SW-trending quartz and calcite veins with disseminated pyrite and accessory sphalerite, galena, chalcopyrite and gold. ESE–WNW- to ENE–WSW-trending quartz veins with disseminated pyrite. This stage is only mineralisation that is hosted by diatreme breccia and clearly postdates.Quartz veins of the first, third and fourth stage are less than 2 m wide. Only breccia veins of the second stage are up to 10 m wide. Gold is present in all stages as microscopic inclusions in quartz and sporadically in pyrite. Macroscopic gold can be seen in the first and second mineralisation stages. Gold commonly occurs in association with sphalerite, galena and chalcopyrite in the second and third mineralisation stages.CITATION:Kucera, J, 2015. Diatreme breccia-hosted epithermal gold deposit at Ridge Mountain, eastern Mindanao, Philippines, in Proceedings PACRIM 2015 Congress, pp 587–592 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Longwall minim; is a highly mechanized, high productivity mining method that is finding increasing applications in coal. Although the method would be highly advantageous in certain hard rock mining applications it cannot be applied in hard rock because no suitable cutterhead exists for such materials. The wedge longwall cutterhead is a, roller cutter device that is wedge-shaped, with cutters arranged to eliminate the very large normal force ordinarily required to cause such cutters to penetrate hard rock. However, the wedge geometry cannot be extended to a point: special nose cutters are needed to open a narrow slot for the wedge. This report describes the design, fabrication, and successful field testing of these critical nose cutters.

Jan 1, 1974

By Enrique Hauser

Discussion of the paper of ENRIQUE HAUSER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 521 to 534. GEORGE A. BURRELL, Pittsburgh, Pa. Mr. Hauser determined the influence of inert gases on the properties of fire-damp mixtures, and one might take some issue with his work on the effect of hydrogen, on those mixtures. It is valuable information to have, but as far as the practical application of it goes, it is not of much significance, because one does not find it in mines, at least not in any appreciable amount. The same Fig. 1.-APPARATUS FUR DETECTING COMBUSTIBLE GASES IN AIR. thing can be said of ethylene. Ethylene is formed in considerable quantities as a product of heat reaction, but normally, in the coal mines, as a result of a great many analyses we have made at the Bureau of Mines, we cannot say that ethylene is a combustible gas found in the fire-damp in coal mines.

Jan 5, 1916

By Tony Peglas, Harry Asche, Eva Wood

The North-South Bypass Tunnel is a new $AUD1.5 billion underground traffic route in Queensland, Australia, a project of the Brisbane City Council. The tunnel is approximately 5.2 km long, bypassing the Central Business District, and is adjacent to and below major buildings and services. Road tunnel alignment issues include the complex southern connections to the Pacific Motorway and the design of ramps to the east and the north. A review of road tunnel alignment criteria and accident data for Australian and overseas tunnels, similar to the proposed NSBT, are discussed. The key findings of this review lead to a rationalization of the traditional tunnel cross sectional width allocation. The road alignment design elements adopted for the NSBT are also discussed. The NSBT route crosses beneath the Brisbane River. Geotechnical investigations and hydrogeological modelling are described. The crossing has a fundamental impact on the alignment and the tunnelling methods. The tunnelling methods to be adopted and the tunnel support are described. The geotechnical investigations and hydrogeology analysis culminate in the selection of a single shielded TBM for the reference design. These outcomes are related to complex issues of hydrogeology and contaminated groundwater. These are discussed in detail.

Jan 1, 2005

Nickel-bearing ores in North-east Dundas have been described by A. McIntosh Reid1 as occurring at the margins of narrow dykes of gabbro, norite, peridodite and pyroxenite, which are intrusive into the Dundas series of slates, quartzites and breccias. They occur chiefly in the neighbourhood of the Five Mile, near Zeehan, as small, narrow ore-bodies which are mostly less than 100 ft. in length.The ores are massive sulphides containing pyrrhotite, chalcopyrite, pyrite and the nickel sulphide, pentlabdite.A less common nickel-bearing mineral, gersdorffite, has been recently found in an adit, which is marked on Reid's geological plan of Dundas as the Hecla mine, 30 chains south of the crossing of the North-east Dundas tramway, over the Great Northern Creek, and at an, elevation of about 350 ft. above the tramway. The occurrence is in a lode traversing the Dundas slates and quartzites, and is situated, according to Reid's plan, about 20 chains beyond the northern extremity of a narrow basic dyke which is continuous for a distance of two miles in a south-westerly direction.The mine eonsists of a prospecting adit following the course of a lode for about 275 ft. in a direction a little west of south. The low values of the lode are indicated by a bulk sample from a shallow winze about 100 ft. from the entrance which is reported by Reid to contain:

Jan 1, 1935

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976

By A. D. Thomas, V. N. Rampton, S. Paradis, C. F. Gleeson

"A shallow till sampling program was completed on a 1 km grid over the St . George Batholith in southern New Brunswick. The ""B"" soil horizon was analyzed for Cu, Pb, Zn, Ag, Co, Mo, U and Sb and the heavy minerals from the ""C"" soil horizon were analyzed for W, Sn and A u. The results delineated four of five recorded W occurrences, three of four recorded Mo occurrences, all recorded Cu occurrences and one recorded Au occurrence. The results indicate that shallow till sampling in conjunction with bedrock and Quaternary mapping can inexpensively define exploration targets in terrain similar to that underlain by the St. George Batholith.A similar program was carried out in eastern Ontario involving the analysis of four separates from the till, the ""8"" soil horizon, the -50 mesh fraction, the -250 mesh and the heavy mineral fraction of the ""C"" soil horizon and humus. Also sampling was carried out near known gold occurrences at closer spacings. Regionally, anomalous results from all sample media clearly defined a large auriferous shear zone and associated splays. Over one known showing all media clearly defined the showing and a secondary zone. On the regional scale the heavy mineral fraction gave the best anomaly definition and contrast, but the -250 mesh fraction was found to be the most cost effective for defining exploration targets. For detailed surveys, humus was found to be cost-effective."

Jan 1, 1986

By Jennifer Ward

The primary objective of this paper is to establish how a low cost, high definition (HD) camera can allow for easy sustainable recordings of blasting operations. The subsequent analysis of each video can be utilized to monitor what type of performance was achieved and aids in improving blasting performance.

Jan 1, 2015