Search Documents

By Steve Skelhorn

Edmonton South LRT is the latest expansion of the Subway system in Edmonton, Alberta, Canada: Consisting of twin 5.8m segmental lined tunnels, 280m long, driven by a Lovat EPB machine. The key challenges were as follows. A 6% downhill grade. Tight radius curves of 250m.Overlying structures within 3m of the tunnel. Strata consisting of sand above the water table, glacial tills and bed rock below the water table. Located within The University of Alberta Campus and adjacent to a hospital. Northern Alberta climate with winter temperatures routinely falling below—minus 30 degrees Celsius. This paper provides a case history and outlines the challenges involved in completing this project.

Jan 1, 2005

By M. A. Trvits, M. Cummins, A. C. Smith, T. P. Mucho

This paper evaluates the effectiveness of remotely applied nitrogen-enhanced foam to aid in efforts to isolate and suppress a mine fire. The foam, in combination with a remotely-installed cementitious mine seal and a novel borehole pressure sampling methodology to determine the location of the suspected ignition source, was used to help control ventilation and inert the area surrounding the suspected ignition source by isolating it from oxygen. This allowed mine rescue teams to safely enter the mine, seal the area, and begin recovery operations to successfully return the mine to full production.

By Dippenaar R, Evans T

Twin-roll continuous casting technology is rapidly approaching commercialisation. Fundamentally different than conventional continuous casting, heat transfer and hence solidification during twin-roll casting are governed by the interfacial melt/mould thermal resistance, as opposed to the resistance of the solidifying shell. Under these conditions the interface resistance is predominantly controlled by the melt/substrate wetting behaviour. The very early stages of melt/mould contact are characterised by highly transient heat transfer conditions. The overall melt cooling rates prior to the formation of the first solid are reported to be in the range of 1000 - 50000 K/s with melt undercoolings of up to 300 K. At the points of intimate melt/mould contact the thermal resistance is approaching zero, where cooling rates and undercooling much larger than those reported in the literature are probably occurring. Improved wetting will reduce the energy barrier for nucleation while at the same time increasing the cooling rate of the liquid. Since the overall nucleation rate is controlled both by the rate of cluster formation and the rate of atom transfer to the nucleus, a critical cooling rate will exist above which the nucleation rate is expected to be reduced. Under these conditions, it is possible that the first solid phase to form is a metastable glass which subsequently transforms into a crystalline phase. The implications on nucleation and early growth are also discussed.

Jan 1, 1999

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

The southern portion of the Swan Coastal Plain, a geomorphological element formed since late Tertiary times, contains commercially exploitable accumulations of ilmenite, zircon, rutile and monazite associated with a series of raised shorelines. The location of the deposits is controlled by a locally outcropping Archaen granite/ granulite complex and a sea current pattern determined by local geography and a prevailing wind direction. A progression from medium to high titanium ilmenite is evident parallelled by progressive leucoxenisation as the age of the deposits increases. Variations in trace element content accompany this process. Circulating groundwater has caused vertical mineralogical variations within individual deposits and by precipitation of iron has formed layers of hardpan.The Geographe Bay deposits are of important economic significance.INTRODUCTIONObservations made during the course of a brief survey of the southern portion of the Swan Coastal Plain provide an outline of the geology and mineralogy of the mineral sand deposits of the area. This preliminary study will require considerable modification in the light of more detailed work in the future.REGIONAL GEOLOGYThe Geographe Bay area is situated in the south-west corner of Western Australia between longitudes 115° O'W. and 116° O'W. and latitudes 33° 15'S. and 33° 45'S.The general geology of the area is shown in Fig. 1 where the control of the physiography exercised by the Cape Leeuwin-Cape Naturaliste basement ridge is readily apparent. Between this ridge and the Precambrian east of the Darling fault lies the southern part of the Perth basin which contains outcropping Jurassic to Recent sediments and lavas (McWhae, et al., 1958).The Leeuwin-Naturaliste ridge is the exposed portion of L Assistant Production Managcr. Laporte Titanium (Aust.) Ltd.

Jan 1, 1964

The following paper describes the refining practice for the production of lead, silver and gold at the works of The Broken Hill Associated Smelters Pty. Ltd., Port Pirie, South Australia.The refinery is situated on the wharf frontage and is built parallel with it. The refinery occupies an area of approximately 3380 square yards. (Fig. 8)There are two buildings, one containing the softening and de-silverising sections, measuring 225 ft. x 57t ft., while the other building, which measures 225 ft. x 90 ft. covers the de-zincing, lead moulding, retorting, cupellation, and dore parting sections. (Fig. 1)The retorting, cupellation, and dore parting sections are completely isolated from the rest of the plant by strong small-mesh wire gratings welded to steel uprights. The dore parting plant and generator room are further isolated by a brick wall, built up to the roof. The two main buildings are steel structures, with outer walls and roof of "Robertson" corrugated sheeting; the side and end walls are open for some distance above the ground, and this, coupled with the high roof which is 50 ft. from ground level, ensures the free access of air and light. Conditions are such that operators work in a clear atmosphere.

Jan 1, 1937

By H Susanto, N Belluz, D Flint, A Edw

The Deep Ore Zone (DOZ) is a block cave mining operation exploiting a diluted reserve of 131 million tonnes grading 1.06 per cent copper and 0.81 g/t gold in the lower portion of the Ertsberg East Skarn System (EESS). The EESS is a calcium-magnesium silicate skarn containing in excess of 250 million tonnes of copper-gold ore, located in the Ertsberg Mining District on the crest of the Jawawijaya mountain range in the highlands of Irian Jaya, Indonesia. The EESS was discovered in 1968 where it cropped out at an elevation of 4050 metres above sea level. The Ertsberg Mining District is underlain by siliclastic carbonate and siltstone formations of Jurassic to Tertiary age. The sediments have been folded and are cut by major bedding subparallel and crosscutting structures. Intrusion of a series of igneous bodies post-dates folding and faulting. These I-type intrusions are the source for the copper-gold mineralisation found in the Ertsberg Mining District. The EESS is hosted by carbonates of the Tertiary Waripi and Faumai Formations that have been altered to calcium-magnesium silicate skarn and is situated on the southern limb of a northwest-trending syncline. The EESS is an essentially vertical tabular body with a vertical extent of at least 1200 metres and a lateral extent of up to 1000 metres. The width of the EESS averages 200 metres and locally is in excess of 300 metres. The northeast (hangingwall) contact of the EESS is a skarn reaction front in sudden contact with barren marbles. This contact coincides with a zone of localised faulting and brecciation. The EESS is bounded to the southwest (footwall) by the Ertsberg Diorite, a 3.25 Ma old intrusive. The DOZ block cave operation extends from 3040 metres above sea level to a maximum of 3388 metres above sea level, has a length of 860 metres and a maximum width of 350 metres. The DOZ is a high temperature skarn with a prograde forsterite/diopside mineralogy whose protolith is the dolomitic Tertiary Waripi Formation. The principal retrograde alteration minerals include tremolite, actinolite, serpentine, talc and chlorite. Grade is highest where bornite occurs in large dense complex intergrowths with magnetite and anhydrite. Grade has been locally enhanced in the DOZ by a late-stage pyrite-chalcopyrite hydrothermal alteration event with associated brecciation. Ertsberg Diorite along the footwall of the skarn is also included in the reserve where it is mineralised endoskarn or has been mineralised by porphyrytic or late stage hydrothermal alteration. Formation of the EESS was initiated by contact metamorphism during the intrusion of the Ertsberg Diorite with later metasomatic alteration during both prograde and retrograde phases. The bulk of sulphide mineralisation formed late in the retrograde phase. The EESS is open along strike to the northwest and down-dip with on-going exploration of these areas. Current exploration is targeting both endoskarn and porphyry style alteration and mineralisation of the Ertsberg Diorite.

Jan 1, 1999

By H. T. Kennedy, S. M. Avasthi

An equation developed for gaseous hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 0.73 percent when applied to 264 natural gas and condensate systems including 2,043 PVT points. Another equation developed for liquid hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 1.12 percent when applied to 346 crude oil systems including 1,759 PVT points. Both equations require composition of the mixture to be expressed as mole fraction of methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide, together with the characteristics of the heptanes-plus fraction in addition to the temperature and pressure. The equations cover wide ranges of the variables involved, and their accuracy is considerably better than that of other available methods. The equations were differentiated to allow calculation of the coefficients of isothermal compressibility and isobaric thermal expansion. (In this paper the coefficient of isothermal com-pressibility and the coefficient of isobaric thermal expansion will be expressed as compressibility and thermal expansion coefficient, respectively.) Equations to calculate these quantities are presented. INTRODUCTION Calculations of reservoir performance for petroleum reservoirs require accurate knowledge of the volumetric behavior of hydrocarbon mixtures, both liquid and gaseous. Compressibilities are required in transient fluid flow problems, and thermal expansion coefficients are important in thermal methods of production. An accurate laboratory investigation of the PVT behavior of each reservoir fluid encountered would be costly and time consuming. For this reason various correlations for predicting fluid properties have been developed and recorded in recent literature. Correlations have been presented in the form of graphs, tables and equations. Since an increasing number of studies are being conducted with the aid of electronic computers, recent efforts have been directed toward development of correla-tions suitable for computer programming. Application of computers permits the use of more complex correlations which otherwise are not feasible. Moreover, methods for predicting reservoir performance, particularly those based on the compositional material balance, depend upon the capability of accurately expressing the molal volumes and other fluid properties as functions of pressure, temperature and composition. The coefficient of isothermal compressibility c is defined by

Jan 1, 1969

By D. I. Bleiwas

The Bureau of Mines determined demonstrated tin resources and costs associated with tin production in order to evaluate the potential for tin production from 18 market economy countries (MEC's). Data were collected from tin producers, in most cases during on-site visits. The analyses evaluated the relative economic and resource position of 146 mines, deposits, or regions in January 1984 dollars. The demonstrated resource of recoverable tin within the nations studied is approximately 2.8 million metric tons (mt). Of this total, over 73 pct is recoverable from the Southeast Asian countries of Malaysia, Thailand, and Indonesia, which in 1983 accounted for almost 60 pct of the world's tin production. Brazil has joined the Southeast Asian countries as a major low-cost, high-volume supplier of tin and is likely to continue to expand its production. Given the 1984 market structure, over 60 pct of the tin in demonstrated resources was economically recoverable. Historically, the International Tin Council (ITC) has helped maintain relatively stable tin prices through a buffer stock and sales quotas. In late 1985, exhaustion of buffer stock funds led to suspension of tin trading on the world's major tin metal exchanges.

Jan 1, 1986

Coking coals are very much in demand on a world wide basis, particularly the higher rank coking coals, which form an important part of many coking blends and which represent the smallest portion of the world'scoking coal reserves. Conventional coke oven plants, using these coals, will predominate at least until the next century.Blending schemes for conventional coking require definition of the basic properties of coals so that the factors influencing the carbonization behaviour may be assessed. Several concepts, which are relatively simple, ate available to help promote a better understanding of the bask factors controlling -coke strength and are also useful in suggesting possible lines to follow in the blending of coals for coking.The interpretation of carbonization behaviour and coke structure in terms of petrographically defined coal rank and type provide a basis for planning and exploitation of coal Teserves. The optimum parameters for coking are suggested as follows.1. Type- Vitrinite content (% m.m.f. by volume) 55 ± 5%2. Rank- Mean maximum reflectance of vitrinite 1.30 ± O.10% Carbon content of vitrinite (% d.m.m.f.) 87·5 ± 1·0%The value of a coal should be assessed in relation to all its possible uses in blends. This is a more realistic and productive approach, as compared with considering coals only in relation to the results of blending with"good" coking coals. Blending schemes have been outlined to assist in the assessment of the blend potential of coals of all ranks and types.Reserves of higher rank coking coals in N.S.W. are very limited and should be conserved by blending with the low rank coking coals, of which there are large reserves.Examination of blending theories in relation to N.S.W. coals suggest that blends in the broad categories of minimal downgrading of the higher rank N.S.W. cok...

Jan 1, 1972

By Fathi Habashi

"Crushing and grinding of ores and their beneficiation by washing away gangue minerals has been practiced since ancient times. Primitive crushing was done by hand pounding the ore with a hard stone then by using metallic hammers. The mortar and pestle was mechanized using a lever and when the size of operations increased in the middle ages, the stamp mill was introduced. The grindstone played an important role in grinding of ores. Panning for gold and hand sorting of minerals were two old methods of separation, now gave way to modern techniques. Flotation started in the middle of the nineteenth century by using oils to collect the mineral particles and float them on the surface of the aqueous slurry. It was only in the 1920s when it was discovered that organic compounds were affective floating agents. Textbooks written by distinguished engineers such as Rittinger, Rickard, Pryor, Taggart, Richards, Gaudin, and others contributed to the recognition of this field as a new discipline to be taught in Universities. INTRODUCTIONThe ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result all efforts were made to enrich the gold by washing away the light gangue minerals (Figure 1). Another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. The present day Georgia was known in ancient times as Colchis and was a center for gold working. It was known to the ancient Greek as the land of Golden Fleece. The use of special cloth to catch gold particles was also described by Agricola in his 1555 book De Re Metallica (Figure 2)."

Jan 1, 2009

By Z. van Zyl

The southern African coal industry is facing the reality that coal reserves are becoming deeper and harder to mine than before. Alternative visions need to be considered to offset the impact of these challenges on productivity, cost, and profitability. One of the main challenges is to maintain current production levels under more difficult conditions, and improve productivity where conditions allow. There is a need to move from the reactive event-based management system towards the more adaptable and flexible process-based management system. This paper focuses on underground coal mining, but the principles are also applicable to other commodities and mining methods. This paper is based on research undertaken by the personnel from Mining Consultancy Services Pty Ltd (MCS) on trends in the underground coal mining sector, as well as practical experience over a period of 16 years in the field of electronic monitoring of mining machinery and productivity optimization.

Jan 1, 2015

By B. Schoevaerts

The ever-increasing depth of mineral extraction presents a challenging environment for hard-rock underground mines. High in situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in South African underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanized installation of a chain-link mesh as evaluation at Gold Fields' South Deep Gold mine situated some 45 km south-west of Johannesburg. A purpose-built mechanized roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been specified as success criteria by Gold Fields: ? A 30% faster installation compared to the conventional methodology ? The mesh should sustain any blast damage when applied to the blasting face ? No unravelling of the mesh when cut ? No failure of mesh under normal conditions ? Reliability of the MESHA® installation handler (availability >90% ? Compatibility of the MESHA® installation handler with AC 282 boomers. Although the energy-absorbing mesh combined with yielding rockbolts is a ground support system of choice for rockburst-prone conditions, the operational upsides recognized during the trial imply that this product can also be competitively used in less demanding ground conditions where weld mesh or shotcrete are customarily used as a primary surface support.

Jan 1, 2012

By I. V. Baklashov

Geomechanical conditions of mining operation are determined by varying in time and space mechanical properties and initial state of the rock mass, by geological and technological factors. We define adaptive mining technology as a technology capable of adjusting to changing geomechanical conditions of mining operation. The ongoing research at Moscow State Mining University consisting of laboratory, theoretical, and field investigations aims at the development of theoretical basis and methodology of the system of geomechanical support of adaptive mining technology for the bedded salt deposit in the Urals, mined by room-and-pillar method. This system of geomechanical support is capable of - dynamically assessing mechanical properties and state of the rock mass varying within the panel; - mapping mechanical properties of the rock mass within the panel; - assessing and predicting mechanical condition of load-bearing elements of the rock mass and its changes due to the adjustment of the parameters of mining operation considering the in-situ geomechanical conditions.

Jan 1, 1996

By Liang Sha

In this study, adsorption of copper by chemically modified orange peel was investigated. A conspicuous change occurs in the surface morphology of the biomass due to modification, which is depicted by SEM images. Equilibrium isotherms and kinetics were obtained and the effects of various factors, including solution pH, contact time, initial metal ions concentration and temperature, were studied by batch experiments. Kinetics was found to be best-fit pseudosecond- order equations. Equilibrium was better described by Langermuir isotherms rather than Freudlich isotherms. At 25?, pH5.30, the maximum adsorption capacity was 70.67mg?g-1 . With increase of temperature, adsorption efficiency decreased. The biosorbent was suitable for repeated use for more than five cycles.

Jan 1, 2009

By Everson P. T, Moyle F. J

Magnesite-rich and dolomite-rich ores from the Savage River region of Tasmania are being considered as potential feed material for a commercial process for production of magnesia.Two selected samples have been characterized by chemical analysis, X-ray diffraction, and differential thermal and thermogravimetric analysis. The materials differ in calcination behaviour, with magnesite decomposing at a significantly lower temperature than dolomite. Calcination conditions have a marked effect on the rate and percentage of magnesium dissolved as the bicarbonate when slurries of the calcine are leached with carbon dioxide. From a process point of view, the feed should have the highest possible magnesite/dolomite ratio, while the optimum calcination conditions are determined by the behaviour of the magnesite component of the feed.From batch calcination tests, it is apparent that the optimum calcination conditions for magnesite-rich ore are a temperature in the vicinity of 700°C and a calcination time of one hour.

Jan 1, 1981