Search Documents

By N. L. Ayres

Tendon support systems have been successfully used to stabilize excavations. Tendon support systems are routinely designed using the axial load-bearing capacity of tendons, namely the tensile strength. To attain tensile strength the tendon must be loaded along its length, which often does not occur in practice. Tendons should optimally be installed at 90° to the surface of the excavation to achieve maximum penetration depth, yet this is often not physically or practically possible, and installations at angles less than 90° occur. Furthermore, the intersection of geological features within the rock mass frequently results in complex loading situations on tendons. The position and angle at which loading occurs results in different combinations of tensile and shear forces acting on the tendon, which can impact on the support performance of each unit and ultimately the whole system. All factors that influence the support system should be understood and taken into account to ensure a sound support design. Combination loading situations are further investigated and tested to obtain a better understanding of the mechanisms involved and the effects on tendon load-bearing capacity. Tendon support units were tested at different installation angles to establish the tendon performance, mechanical behaviour, and load capacity during these loading situations. The results and outcomes are aimed at providing rock engineers with additional data and improved understanding of how tendons could perform under certain conditions.

Jan 1, 2014

Detachment of Particles from Bubbles in a Stirred Cell

Sep 13, 2010

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of 'overburden modification' due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and 'overburden modification' has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

By Patrick J. Hannigan

The pile foundation designer typically performs a subsurface exploration program and static pile capacity calculations before selecting a pile foundation type, length, and capacity. During construction, a pile installation criterion must be established to meet these design requirements. This installation criterion usually consists of a minimum penetration resistance or blow count to confirm pile capacity and may also include a minimum embedment requirement. This text will focus on use of wave equation analysis and dynamic measurements to meet design requirements. BEFORE THE WAVE EQUATION Since the mid-1800s, over 450 dynamic formulas for pile driving control have proliferated. In their simplest form, these formulas relate hammer energy to the work of soil resistance, or simply: W ? h = R ? s (1) Where W = ram weight h = ram drop height or stroke R = pile capacity s = pile penetration per blow

Jan 1, 1990

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.' Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,' and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

Underground equipment owners and users in order to compete and succeed in being viable business propositions must continually balance costs with productivity. By reducing their hourly ownership, operation and maintenance costs and increasing their hourly production, the cost per unit of material mined will be optimized.

Jan 1, 1990

By M. Superfesky, P. Michael

Introduction The US Office of Surface Mining (OSM) is proposing changes to the Code of Federal Regulations in the interest of minimizing the adverse effects of excess-spoil-fill construction on the “prevailing hydrologic balance, fish, wildlife and other environmental values” (70 FR 35112). The proposed changes will require: (1) minimization the amount of excess spoil generated at a mine site; (2) minimization of the size of the fills constructed; (3) consideration of alternative configurations for disposal; and (4) development of a disposal plan that would minimize adverse impacts to the environment.1 To achieve those objectives, mining companies operating in steep-sloped Appalachia will likely build excess spoil fills (also called valley fills) that toe out at higher elevations in the hollows (i.e. to prevent or limit burial of streams). Consequently, the slopes of fill foundations will generally be steeper. Whereas the authors of this paper support these measures to protect the hydrologic balance and general environment, we wish to point out that placement of fills on steeper foundations can negatively impact the stability of the fills if proper care is not taken during their construction. It is important to note that in addition to impairing human safety, valley fill instability can negatively impact streams, the riparian habitat etc., and thus defeat the very purpose of the spoil minimization measures proposed. We do not, however, propose additional regulatory requirements pertaining to valley fill stability. Rather, we intend to emphasize the importance of engineering requirements already on the books, especially as they apply to the predominant type of valley fill constructed: the durable rock fill. We believe that the practice of restricting valley fills, to higher elevations in the watershed leaves less room for error in the design and construction of stable structures. This paper gives a quick review of the nature of excess spoil generation; methods and requirements of excess spoil fill construction, and the to-date stability record of the fills. The interest in excess spoil minimization and how it affects valley fill construction is also discussed. Most importantly, we will review long-standing issues pertaining to proper design and construction measures with respect to durable rock fills and discuss how they will become more critical as spoil minimization is practiced.

Jan 1, 2007

THE township of Costerfield is situated in the parish of Costerfield, county of Dalhousie, and lies 6 miles east of Heathcote and 30 miles south-east of Bendigo. It is separated from Heathcote by the Mt. Ida Range, which forms the western boundary of the Silurian formation. It is situated at the head-waters of Tin-pot Creek, a small southerly tributary of the Deegay Ponds Creek, which flows east to the Goulburn River.The field was discovered in 1860 by two prospectors, Coster and Field, who were guided there by a shepherd, M Nicol Coster and Field had already discovered an antimony lode about three miles nearer Heathcote, when M Nicol offered to guide them to the larger outcrop. The main Costerfield reef at that time projected above the surface, and was white through oxidation, though the bluey sulphide showed on fracture. No alluvial gold of any consequence was obtained at Costerfield, but a little was obtained, at Redcastle, 7 miles to the north, and in some of the gullies to the east.Following its discovery there came a period of prosperity to Costerfield, while the mining operations were confined to the oxidized zone. The early success of mining at Costerfield was due to the gold values, and it is probable that the oxidized zone was secondarily enriched. The earliest available record of values is a crushing of Coster and Co. on the Antimony reef (now known as the Costerfield reef), when 200 tons from a depth of 70 ft. averaged 4 oz. per ton in July, 1861. At this time a crushing mill had not yet been erected at Costerfield, and the ore was carted and treated at Redcastle. The massive antimony ore, consisting of mixed oxides and sulphides, was separated by hand-picking as "marketable ore," and the remainder crushed for gold. A higher average is recorded from South Costerfield in September, 1861, when a 15' cwt. parcel...

Jan 1, 1922

By A. Azizi, P. Blatter, A. Bouajila

"Due to the high reactivity of sulfide minerals in alkaline cyanide solutions, some parasitic reactions inflict a heavy gold surface passivation and excess cyanide consumption resulting in a dramatic decrease of the gold leaching rate. Atmospheric pre-oxidation was shown to be an effective tool to enhance gold extraction by preventing a passive film from forming on the surface of gold grains. This work aims to highlight efforts undertaken to determine: (1) how gold cyanidation is limited by passivation; (2) what are the reactions and mechanisms involved during gold cyanidation; and (3) how a better understanding of fundamental issues can be used to design a proper pre-oxidation strategy. INTRODUCTION Precious metals (PM), gold in particular, naturally occur in contact within a wide range of sulfide mineral systems. Hence, one of today’s most challenging R&D tasks consists in accounting for the presence of sulfides on the cyanidation behavior of gold. An important body of knowledge reveals that metal sulfides display a range of reactivities in alkaline cyanide solutions (Marsden & House, 2006). Such reactivities are acknowledged to inflict additional utility costs and loss of profits because they are accompanied with higher consumption of cyanide and/or formation of undesirable by-products that are often detrimental to gold leaching rates. Gold recovery in cyanidation is hampered by a multitude of factors, among others: (1) consumption of excess cyanide as a result of the formation of thiocyanate and dissolution of transition (Cu, Fe, Zn, etc.) metals (Habashi, 1967); (2) gold surface passivation by solid reaction products, e.g., Fe(OH)3 (Guo, Deschenes, Pratt, Fulton & Lastra, 2005), sulfur (Dai & Jeffrey, 2006; Jeffrey & Breuer, 2000;) or oxo and thiooxo (SbO33- SbS33-) salts in alkaline solutions (Guo et al., 2005). Because of their energy structure, most of the sulfide minerals exhibit semiconductor properties (Marsden & House, 2006). Therefore, the contact between constitutive sulfide minerals inside complex sulfurous ores entrains electrochemical phenomena in which sulfide dissolution is a genuine corrosion process (Azizi, Petre, Olsen & Larachi, 2010). For instance, galvanic interactions could be initiated between the various constituents within the ore and could substantially increase or decrease the reactivity of some of the associated minerals."

Jan 1, 2012

By Per-Anders Persson

This chapter deals with the concepts ofshock waves aud detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mrc!~amcal work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1994

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

By W. H. Schiffbauer

The protection of miners, equipment, and infrastructure is discussed. While the primary focus of the described technology is to prevent miners from being injured, struck-by, or crushed by heavy equipment; another major benefit realized is also the protection of equipment and infrastructure. An attempt is made to define and classify the systems used to provide proximity detection and warnings as well as collision detection and avoidance. Information about the speed of vehicles and human operator response time can be a factor in the choice of what type of system and what features are needed to properly address the needs. How the technology adjusts to compensate for various vehicle speeds, while maintaining the same level of protection is noted. The statistics which justify the need of miner protection are provided. The primary system components required, what attributes they feature, and how they respond in the environment, is briefly highlighted. The physics behind the danger zone marker technology and what makes it so robust and reliable is established. Examples of a few mining applications and specific operational modes are provided for both surface and underground.

Jan 1, 2011

By L. M. Dyer

Various attempts have been made to build leadership and management expertise with little success. There are numerous reasons these attempts have failed. Three reasons, along with suggested solutions, will be explored: 1) lack of ownership of the development process by those affected; 2) lack of congruence of the development process used and the business strategies of the organization; and 3) a comprehensive development process. We will discuss a development model applied inside a smelter and refining complex over one year involving all levels of management. The process was credited with helping to substantially reduce cost and enable breakthroughs in production, quality and safety results.

Jan 1, 2000

By Edward L. McHugh, Charles Sabine, David G. Long

While less than 1% of reported mine accidents are associated with slope stability problems, slope failure accidents were responsible for about 15% of U.S. surface mine fatalities between 1995 and 2003. Small rockfalls, which may involve hand-sized rocks weighing only a few pounds, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic yards of material or more can be fatal even for heavy-equipment operators. As part of an ongoing study at the Spokane Research Laboratory, several remote sensing technologies are being evaluated as tools to assess slope stability and monitor slopes for hazards. An interferometric radar device capable of detecting very small displacements on slopes has been assembled and tested. Radar techniques can provide new tools to augment current methods for monitoring ground control hazards in mines.

By Serge Ouellet

Identification and quantification of cementitious phases in cemented paste backfill (CPB) is difficult due to the fineness of tailings and the low binder content used in the mixture. Techniques such as X-ray diffraction and thermogravimetry were ineffective (mainly due to tailing mineral interference) to identify and quantify hydration products in most works reported in the literature. On the other hand, scanning electron microscopy (SEM) was used in many cases but mainly for qualitative purposes. This paper presents the development of a new approach based on a computer program (SEM-XMAP) that combines X-ray dot mapping images acquired by SEM and generates a coloured image representing the mineralogy and the microstructure of a given CPB specimen. The technique is applied to one CPB sample mixed with blast furnace slag (BFS) and acidic sulphated mixing water sampled in a mine dewatering system. The technique allowed identifying calcic matrix, unhydrated and partially hydrated BFS particles, and sulphated phases.

May 1, 2007

By Gunderson C. T

The use of carbide tipped integral drill steels and detachable bits is discussed in relation to the means of drilling or cutting employed. It is stressed that only by correct use can the full value of these tools be realised.Factors affecting carbide quality, the design of shanking steels and the requirements and techniques of brazing in inserts are considered.It is essential that the brazed jointing between carbide and steel be strong but ductile. The methods used for the manufacture of carbide tipped tools are briefly outlined.INTRODUCTIONIn recent years the application of tungsten carbide to various mining tools in the mining industry, has developed to the stage where it is now regarded as an essential item in the production of coal and metal ores. In fact it is claimed that certain mining operations would not be possible if it were not for the benefits obtainable from the characteristic properties of tungsten carbide. The advantages of this hardmetal have, to some extent, influenced manufacturers to revise design specifiations of some machines, while againsome machines have actually been designed with tungsten carbide as their basic medium for operation.In general the applications fall into the following three categories:(a) Drilling hard rock by percussive means.(b) Drilling soft rock and coal by rotary means.(c) Coal cuttingThis paper is concerned with tungsten carbide tools associated with these three activities in Australia, the effectiveness of their application and significant points in their design and manufacture.

Jan 1, 1958

By Randall M. Wheeler

It is important to be able to quantify the effects of blast delay designs on vibration characteristics. White was the first company to develop commercially available software, called Alpha-Blast, for this purpose. The program can indicate relative amplitude and frequency results to be expected from the use of particular delay intervals. If enhanced vibration effects from delays are a problem, a technique to evaluate this situation will be invaluable.

Jan 1, 1994

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy' operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006

By W. J. Birch, R. Farnfield

The use of electronic detonators to control blast vibrations has been previously established by many authors. This is performed by determining the optimum delay period between the blast holes for a particular pattern that can accurately control the firing frequency of the blast, which in turn has a direct bearing on the frequency composition of the ground vibrations recorded at a particular location. This was established by Pedgen, Birch, Hosein & Farnfield (2006) whereby like-for-like comparison tests between non-electric and electronic blasts were carried out in a limestone quarry in northern England. They demonstrated that resulting peak particle velocity values recorded at near and mid-field distances were primarily a product of the firing frequency of the electronically initiated blasts.

Jan 1, 2009

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960's. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000