Search Documents

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Rodrigo Toro, Mario Delisle, Claudio Zamora

"The mining market is researching innovative methods to train the workforce for mining which is normally extremely difficult to get. Thus, the dynamic simulation-based technologies become an essential pillar to educate and train the inexperienced staff at the pace required by this industry. Even if Operator Training Simulator (OTS) systems are commonly used in most of industries, knowledge transmitted to operators are unfortunately not ""capitalized"" in general. The OTS systems are usually delivered as a single hardware and software platform and very little as a full service long-term.In this article, an integrated solution to increase the efficiency of the operators is proposed. This solution is based on the combination of dynamic simulation, processes knowledge, virtual reality and the knowledge capitalization through the creation of simulation scenarios and e-learning. The Codelco Ministro Hales plant simulation project for a copper concentrator plant is presented as a real life example.IntroductionDynamic and real-time process simulation have proven to be a must in the development of greenfield projects, providing mechanisms to design and test controls design, interlocks, start-up, shut down sequences and operator training, among others (see (McMillan, 2006) for further details). Early adopters of this technology were utility power plants; in the petrochemical industry have become a standard, and in the mining industry the use of dynamic simulations is growing, especially in new projects and training of operations personnel for the adoption of best practices and new technologies, see (Nikkhah & Anderson, 2001) and (Toro, Ortiz, & Yutronic, 2012).This paper outlines a solution that utilizes dynamic simulations as the base of an integrated platform for operational effectiveness, which takes into account the current scenario of new mining projects and operations, where high turn over rates and needs of specialized workforce have given a special value to this kind of technologies."

Jan 1, 2015

By S. Rivard

"This paper demonstrates the selection of grinding circuit technology for a number of recent projects including discussion of the key drivers and the role of energy efficiency. Decreasing head grades combined with a strong and sustained increase in operating costs has forced miners to examine increased project size, increased equipment capacity and efficiency improvements in order to reduce their unit operating costs and improve overall project economics. Comminution energy consumption, safety and capital cost considerations play a critical role in the success of projects. This paper presents some key guidelines for a successful and cost effective comminution circuit design and includes a case study on three projects, outlining the issues and the drivers which led to the ultimate circuit selection and the critical role that energy efficiency played.IntroductionComminution circuits for minerals processing are selected based on their suitability and efficiency in reducing run-of-mine ore to the desired feed size for the downstream process. The input material (ore) properties and downstream process requirements are the key determinants and there are standard approaches for each circumstance.The minerals processing industry has been a fast adaptor of efficiency improvements based on increasing capacity of equipment (e.g. trucks, crushers, mills, pumps) but less successful in adapting radically new technologies that disrupt incumbent flowsheets or processes.The installed power of grinding mills has increased linearly over the past 25 years (Meka & Lane, 2010) and pumps and classification equipment have kept pace. The autogenous grinding (AG) and semi- autogenous grinding (SAG) mills displaced stage crushing as a dominant method of coarse rock breakage in many applications causing crusher manufactures to increase the capacity of cone crushers to meet the competitive demand.Examples of new comminution technology in the 20th and 21st centuries are the development and adoption of cyclone classification in the 1940s (Newtech, 2016), AG milling in the late 1950s, vertical grinding mills in the 1980s, high pressure grinding rolls (HPGRs) also in the 1980s and ultrafine milling technology in the 1990s (Meka & Lane, 2010)."

Jan 1, 2017

By J. Châteauneuf, R. Dupéré, D. Mrabet

"In gold processing plants, it is common to start gold cyanidation in the grinding circuit by simple cyanide addition or as a result of recycling residual cyanide. In such cases, advantages such as a decrease in gold lockup and reduced leach time have been noticed. The prevailing conditions in grinding circuits such as intense mixing, particle breakage and friction or high temperature are quite different from those found in tanks and so is the resulting cyanidation behaviour. To gain a better understanding of the cyanidation behaviour in mills and of the pertinence of cyanide addition in grinding circuits, lab tests were conducted using an industrial ore from Canadian Malartic mine. In this study, the effects of different parameters on cyanidation in grinding circuits were examined; parameters such as such as temperature, dissolved oxygen, cyanide concentration and pH. The results showed that the kinetic benefits of high temperature in the mill can overcome the low dissolved oxygen concentration thus leading to an overall gold dissolution kinetics improvement for temperatures up to 50°C. However, gold leach in the studied grinding circuit at lab scale caused an increase in cyanide consumption with a higher generation of iron cyanide and SCN-. These results were confirmed by tests in the Canadian Malartic plant where the cyanide addition was moved from the SAG mill to the leaching tanks resulting in a 20% savings in cyanide consumption.IntroductionCyanidation in grinding circuits can benefit gold processing by decreasing gold lockup and by reducing leach time. However, other aspects regarding gold and cyanicide dissolution come into play in the conditions prevailing in grinding circuits. Indeed, high turbulence, high temperature, recycling load, friction and particle breakage make cyanidation behaviour in grinding circuits different from in-tank cyanidation (Marsden and House, 2006). In several cases, cyanide in grinding is limited to a very low level or completely avoided such as in circuits with gravimetric separation, for ores requiring oxidative pretreatment or for preg-robbing ores. In other cases, water management imposes a certain recycling of residual cyanide. This problem is generally addressed by a case-by-case approach. However, the chemistry of cyanidation in mill circuits is worth investigating in order to assess the advantages and disadvantages."

Jan 1, 2016

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By Fred W. Snow

This paper describing the mining practices at the Magma mine, Superior, Ariz., is one of a series being prepared by the Bureau of Mines on mining prac¬tices, methods, and costs in the various mining districts in the United States. At present (1929) practically all the mineral production in the Superior district is from the Magma mine of the Magma Cooper Co. The ore is mined for its copper but contains associated silver and gold. Both direct smelting ore and ore of concentrating grade are produced. The mining methods now in use at the Magma mine were adopted or developed as knowledge was gained of the physical condition of the ore bodies and the inclosing formations; the wall rock is soft and crushed and the ore is relatively hard. In general, existing methods have been adapted to fit local conditions, but some of the mining practices used were originated at this mine. Most of the ore is mined by a combination of rill stopes and pillar stopes. The pillars are extracted by underhand mining.

Jan 1, 1929

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By X. S. Yuan

With the production increase of Oil Sand in Fort McMurray Alberta, more efficient tailings disposal has become a priority for Syncrude Canada Ltd. A lot of work on tailings research and development has been compiled to determine the most effective deposition to increase reclamation options, water re-use and thermal energy recovery. Efficient flocculation of fine oil sand tailings is the key technology for thickening. It was identified that flocculation of fine transition/marine ore tailings using a single flocculant was not effective. The thickener overflow contains 1-4% solids content compared with the target solids content of <0.5% obtained with Estuarine ore. As a result, novel processes for treatment of fine transition/marine ore tailings have been developed at Syncrude Bitumen Production Development since June 2004. While the conventional processes using a single flocculant, a single coagulation, or a coagulant-flocculant combination was ineffective for transition and marine ore tailings, the new processes including Coagulation-Flocculation-Coagulation (CFC), Flocculation-Coagulation (FC) and Flocculation-Coagulation-Flocculation (FCF) were acceptable options. The key components of these technologies consist of the recipe of chemicals and their adding sequence. With these technologies, almost all sub-micron clay minerals are aggregated together and settle as a whole, resulting in a clear supernatant of less than 0.1% solids.

Jan 1, 2006

By Simon D. Handelsman

?Artisanalmining ?Application of human energy (e.g. pick & shovel) directly to produce minerals ?majority no technical skills and lack adequate working tools ?Small-scale mining ?Application of modern technology for limited scale mineral production Significance of ArtisanalMining ?15 million people in artisanaland small scale gold mining ?55 developing countries ?Use of mercury damages health of 100 million people

May 1, 2006

By W. L. Dare

This publication is one of a series prepared by the Federal Bureau of Mines on methods and costs of producing uranium ore on the Colorado Plateau. The information it contains was gathered in 1955-58 and applies to eight small operations. (See fig. 1.) Mining costs have increased since the data were I collected, but the information should be helpful in estimating future costs I at similar deposits. The Bureau of Mines had early experience in the production of carnotite-type ores on the Colorado Plateau.3 4/ Under a cooperative agreement with the National Radium Institute in 1914-16, the Bureau mined and concentrated carnotite ore for recovery of radium, uranium, and vanadium. The ore was taken from claims in or near Long Park Montrose County, Colo., about 3 mi. south of La Salle Mining Co.&apos;s La Salle mine, which is one of the mines described in this report. The Bureau leased the claims from Crucible Steel Mining & Milling Co., a subsidiary of Crucible Steel Co. of America, and from 1914 to 1916 produced 990 tons of high-grade ore, containing 2.6 pct. U308, and about 2,000 tons of mill-grade ore, containing 0.85 pct. U308. The high-grade ore was shipped directly to a radium-recovery plant built in Denver in 1914 under the cooperative agreement. There, commercial methods of extracting uranium, vanadium, and radium from carnotite ores were developed by Bureau personnel. The lower grade ore was concentrated at a small mill in Long Park before being shipped to Denver. The final recovery was 69,000 lb. of U308 and 8.8 g. of radium. The direct mining cost of producing the high-grade ore, including the labor to hand sort and sack it, was $35.96 per ton. Freighting the ore 58 miles to Placerville, Colo., the nearest rail point on the Rio Grande Southern Railway, cost $25.28 per ton, which included $4.55 per ton for ore bags and twine. Four-or six-horse teams pulled two wagons in tandem and made the

Jan 1, 1961

By Gerald L. Stolarczyk

Safe and efficient coal extraction requires advanced radar subsystems that can be mounted on cutting drums of coal cutting machines. A look-ahead radar (LAR) must solve the radio geophysics problem of transmitting an electromagnetic (EM) wave through at least 20 feet (6.1 meters) of coal to an air- or water-filled void. The reflected EM wave must be processed in the radar electronics to determine the physical distance to the void. Horizon sensing enables selective cutting near the undulating sedimentary rock boundaries of the coal bed to address coal quality and ground control issues. Both sensors require subsystems for dynamic electric power generation, real-time measurement of drum rotation angle, detection of reflected EM waves, and processing to determine distance through coal and RF modem transmission of measured data to the mining machine. This paper describes the development of the subsystems and field test results.

Jan 1, 2006

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Scott Crabtree, Randy Wheeler

Theoretical description of destructive wave interference and the use of sacrifi cial holes is included and is supported by data collected at Springfi eld Underground. Finally, the process by which the reduction in vibration was achieved in practice is described. Results are discussed for several production blasts taking place over a one year period.

Jan 1, 2008

By C. Hosten, K. V. S. Sastry, D. J. Kawulok-Englund

Introduction Since the last decade the iron ore processing industry has undergone drastic changes from supplying screened and natural ores to manufacturing tailored concentrates and pellets. Increased need for the beneficiation of lower grade iron ore deposits and the increased demand for higher grade concentrates necessitate finer grinding of iron ores before concentration. The normal filtration stations used in the past are experiencing difficulties in dewatering the finely ground concentrates to moisture levels acceptable for balling. In addition to finer grinding, applications of complex beneficiation techniques has decreased the filterability of the concentrates and create problems in filtration of iron ore concentrates. An overview of the filtration literature indicates there are few research reports on the dewatering of iron ore concentrate slurries. There exists a need to understand the principles and mechanisms involved in the filtration of iron ore concentrate slurries with a goal of developing more efficient filtration techniques. This paper presents the results from the first phase of our research program that included the development of a reproducible benchscale filtration technique and the investigation of the filtration behavior of eight iron ore concentrates.

Jan 10, 1983

By Robert L. Lappi

Volume I of this report described the demonstration of cross-ridge mountaintop coal mining. This document, Volume II, is intended for use as a supporting document to Volume I. This report describes the MATHMINE Mine Simulation System, a modularized software system used to support the demonstration of cross-ridge Mountaintop coal mining. The MATHMINE Mine Simulation System was used to generate mine plans for coal extraction at lowest cost. The functional details, data requirements and output of the software system are detailed here. The computer program was written in FORTRAN. One module which generates resource location data required the use of SAS?.

Jan 1, 1984

By W Herrmann, R R. Large

Volcanic-hosted massive sulfide (VHMS) deposits in ancient, submarine volcanic belts of Australia include mound, lens and sheet-style Zn-rich polymetallic deposits, massive and disseminated pyritic Cu-Au deposits and disseminated, stratabound Au-only deposits. Variation in morphologies, metal ratios, volcanic environments and alteration features indicates there exists a spectrum of deposits from the classic VHMS model, to hybrids between VHMS-porphyry Cu and VHMS-epithermal end members. Zn-rich, polymetallic deposits form eitheron, or just below, the seafloor, whereas the Cu-Au and Au-only deposits form sub-seafloor by replacement of specific volcanic lithologies. Alteration zoned outwards from quartz -> chlorite -> sericite ¦ carbonate is typical of VHMS deposits across the spectrum. Quartz and carbonate alteration is dominant in the Au-only systems,chlorite alteration is commonly developed close to Cu-rich ores, and sericite and carbonate alteration zones are well developed in the stratiform Zn-rich ores. The most useful geochemical vectors for Zn-rich ores are the alteration index [AI=100(MgO + K2O)/(MgO + K2O + CaO + Na2O)], the chlorite-carbonate-pyrite index [CCPI=100(MgO + FeO)/(MgO + FeO + K2O + Na2O)], Mn content of carbonate, Mg/(Mg+Fe) ratio of chlorite,whole-rock Tl, Sb and Ba/Sr ratio, S34S of pyrite, and whole-rock S18O. The most useful vectors for pyritic Cu-Au ores are AI, CCPI, S/Na2O ratio, Na content of white mica, and Fe content of carbonate.

Jan 1, 2002

By Axel Studeny

Geomechanical-numerical methods are an established tool for planning of underground excavations worldwide. By describing the interaction between heterogeneous layered strata and support elements it is possible to determine their suitability. The German hard coal mining industry has more than twenty years experience in investigation and using these parameters to carry out numerical calculations. Today, nearly all excavations (shafts, pit bottoms areas, bunkers, coal faces, development drivages, gate roads etc.) are calculated by geomechanical-numerical tools in combination with empirical planning methods. A high accuracy of planning results, which is a special requirement in the German coal industry with its deep-level longwalls, bedded and weak surrounding strata and multiple seam mining layouts, depends on the extensive calibration of the numerical models, which is achieved by: 1) Taking a large number of underground measurements with empirical evaluation. 2) Carrying out physical modeling. 3) Using the characteristic features of the installed support elements. This paper compares the planning approach used for multiple and single seam mining and presents the advantages of this planning tool. The main focus is on the feasibility of rockbolting as the sole means of roadway support for multiple seam mining operations, though the paper will also look at how the costs can be improved by using a low bolting density in single seam layouts.

Jan 1, 2007

By Gregory J. Canivan

Three test pile programs were conducted in Charleston, South Carolina to evaluate differences in bearing resistance due to installation methods. The tested piles were installed with impact hammers and vibratory drivers through soft clays and/or loose sands into the Cooper Marl, a stiff calcareous marine clay or silt. Piles driven into the Cooper Marl experience significant capacity gain with time following initial installation due largely to pore pressure dissipation. Pile size and pile type were both known to affect pore pressure generation during installation and subsequently the capacity gain with time. The test programs were primarily conducted to optimize pile design values and construction methods with regard to trestle construction but the results also contribute to the understanding of driven pile behavior. High strain dynamic testing was performed on several open-end pipe and H-piles. The measured difference in long-term bearing capacity of the H-piles as a result of the two installation methods was negligible, while the short-term bearing capacity of the pipe pile was larger when the piles were installed using impact hammers. The lower short-term resistance in the vibratory driven piles is attributed to larger excess pore pressures generated during installation compared to those generated during impact driving.

Jan 1, 2002

By Joshua Taylor Drake

This report answers specific questions concerning underwater blasting considerations, and blasting safety. The blasting considerations discussed consist of basic blasting principles, and new variables to be accounted for. Blasting safety will include the safety of personnel and structures. The environmental considerations will also be discussed with mitigation methods. To be most effective, this document requires the reader to be familiar with key fundamentals of explosive engineering. In order for a blasting professional to benefit from this report, the following questions will be asked:

Jan 1, 2015

By L Lachance, F Flament, D Leroux, S GariTpy

"Considerable metal values are often locked in stockpiles (ore, concentrates, heap leach pads, slags, reverts, etc.) and process equipment (bins, holding tanks, thickeners, etc.). This is more than enough to justify accurate accounting of such in-process metal inventories from both financial accounting and operational perspective. However, accurately determining the metal inventory of an in-process unit is often a challenge in industrial practice. Audits have shown that available indirect or direct measurements often carry large inaccuracies. Sooner or later, ignoring these measurement errors lead to unexpected incoherencies in reported metal balances. In such situations, coherent metal balances are then achieved through subjective and sometimes significant adjustments of in-process inventory levels. While such metal accounting methods applied by mineral processing engineers used to be rarely challenged, they are now being increasingly scrutinised by various stakeholders. Hence, metal accounting procedures that mitigate subjectivity in adjustments while still coping with the unavoidable uncertainty are more relevant than ever.This paper reviews three different metal accounting methods for reporting in-process metal inventory values. Their individual application strongly depends on the available measurements i.e. The indirect method where the metal inventory of a given process unit is determined by subtracting the cumulative reclaim from the cumulative feed carries important flaws. The direct method also comes with challenging accuracy issues so that emptying a process unit is often the best available inventory measurement. This reality is recognised for by further analysing a previously proposed operating mode where two interchangeable process units are alternately used. The third investigated method is the redundant method which combines indirect and direct methods for a given process unit. This paper reveals that the dual process unit operating mode and the redundant method can both significantly improve the estimation quality of in-process metal inventories.CITATION:Lachance, L, GariTpy, S, Leroux, D and Flament, F, 2013. Review of metal accounting methods for in-process metal inventories, in Proceedings MetPlant 2013, pp 102-117 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996