Search Documents

By P. J. Bethell

Background Increasingly complex geological conditions, with the presence of high ash binders in the mining horizon were encountered at the A.C. I. Dugout Mine near Price, Utah. This led to the production of high ash coal from the Dugout Mine during 2003 and 2004. This material had poor marketability and posed operating issues for the utilities burning the coal. Ash levels increased from typical levels in the 9-12% range to between 15 and 25%. etween 15 and 25%. Reviews of the mine plan and expected geological conditions indicated that further periods of high ash production could be expected. Action Plan Detailed sampling of the mine high ash production was carried out. The majority of the coal from the Dugout Mine is trucked to the Savage Coal Terminal (SCT) at Wellington, Utah where it is stored in multiple piles by quality. Coal at the mine is segregated by a CoalScan 2600, on-line analyzer into high ash, low ash and rock chute (waste material). From these piles, the material is crushed prior to shipment to SCT. The samples obtained from the various high ash piles were subjected to detailed sizing and washability analysis. Once this information was obtained, alternative circuit configurations were evaluated to process this material into a salable product. Water supplies in the arid terrain where the plant is located are scarce. This factor played a part in the final circuit design.

Jan 1, 2008

By John S. McCartney, Ismaail Ghaaowd

This study presents the results from centrifuge modeling experiments performed to understand the effects of temperature changes on the pullout capacity of scale-model energy piles embedded in normally- consolidated clay layers. The energy pile under investigation is an aluminum cylinder instrumented with internal strain gages and thermocouples, and its temperature is controlled using an internal electrical resistance heater. The energy pile was first heated until the temperature, pore water pressure, and volume change of the surrounding clay layer stabilized, after which the energy pile was cooled. Pullout tests were then performed on the energy piles heated to different temperatures to understand the effects of the preceding heating-cooling cycle on the pullout capacity. In addition, the clay undrained shear strength profiles were measured using push-pull T-bar penetration tests before and after heating. INTRODUCTION When a heat source such as an energy pile is embedded in a saturated clay layer, temperature changes will result in changes in pore water pressure as the rate of heating is typically faster than the rate of pore water drainage (Campanella & Mitchell 1968, Abuel-Naga et al. 2007, and Ghaaowd et al. 2016). Although all soils will initially expand during undrained heating, normally consolidated soils typically exhibit permanent contraction while overconsolidated soils exhibit expansion after sustained heating when drainage is allowed (Vega & McCartney 2015). Subsequent drained cooling typically leads to elastic contraction. Thermally- induced changes in pore water pressure and volume during transient heating and cooling may affect the soil- structure interaction of energy piles, as well as the ultimate capacity of the energy pile. This study is relevant as relatively few studies have been performed on the behavior of energy piles in soft clay (e.g., Ng et al. 2014), with most focused on the behavior of drilled shaft energy piles in stiff rock or overconsolidated clays (e.g., Laloui et al. 2006; Murphy et al. 2015; Wang et al. 2015; McCartney and Murphy 2017).

Jan 1, 2018

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

The works of Metal Manufactures Ltd are situated at Port Kemblam NSW, within a few hundred yards of a deep-water harbour. At present they occupy about 26 acres, and ample provision has been made for future extensions. Rail connection exists between various parts of the Works and the main South Coast Railway, the harbour jetties and the adjacent copper refinery of The Electrolytic Refining and Smelting Co Ltd. A plan of the works is shown in Fig 1.The company was incorporated in March 1916, and commenced production of copper wire in June 1918. Early in 1920, tube manufacture was undertaken, followed by telephone cable mnufacture in 1923. Today the Works consist of five principal sections: Founrdy, Tube Factory, Wire Factory, Cable Factory and Case and Drum Factory. Whilst the last four are engaged in producing the finished materials for despatch from the Works, the first-mentioned is engaged in producing copper, brass, and other non-ferrous billets for use in the Tube and Wire factories. In addition, there are Engineering and Metallurgical Departments supporting the manufacturing sections, and in these, as well as in all other sections of the Works, extensions have been carried out from time to time to provide for increased output and new types of products.

Jan 1, 1938

By Albert H. Clough

The Coast Range subarea of the Juneau Mining District (JMD) extends from the Canadian border north of the community of Skagway, southerly to Tracy Arm. It is bounded by the international boundary on the north and eastern edges. The Ferebee Glacier and Lynn Canal mark the western boundary, extending south to the Berners Bay region. From Berners Bay south, the western boundary is the eastern boundary of the Juneau Gold Belt (fig. E-l). The city of Skagway (fig. E-2) is the only developed community within the confines of the subarea. Skagway was originally established as a port for the Klondike gold rush of 1898. Recently, Skagway has gained prominence as a port for shipping goods into and mineral products out of Yukon Territory (fig. E-3). Skagway has also developed a thriving tourist industry based on its Alaskan traditions. The community of Skagway maintains a paved airstrip which is suitable for use by small multi-engine aircraft. Several regional air carriers serve Skag-way with frequent scheduled flights, especially during the summer months. Helicopter charter services are available from Skagway during the summer months.

Jan 1, 2012

By Hyung Jeek Kim, Jongmin Joo, Jonguk Kim, Jai-Woon Moon, Kyeong-Yong Lee

"Co-rich ferromanganese crusts (Fe-Mn crusts) distributed on seamounts in the western Pacific are potential economic resources for cobalt, nickel, platinum, and other rare metals in the future. Evaluation and selection of a mining site can be established based on abundance and grade of Fe-Mn crusts in the site as well as topography that should be smooth enough for mining operations. Therefore, acquisition of shipboard echo-sounding and acoustic backscatter data are prerequisite to the selection of potential mine sites in addition to visual and sampling operations. Acoustic backscatter data can be used to locate crust-covered areas on a regional scale with the understanding of acoustic properties of crust through its correlation with visual and sampling data.During an expedition that took place from January to March 2014, KIOST collected geophysical and geologic data to assess the resource potential for Fe-Mn crusts on three seamounts (guyots) in the Western Pacific. In OSM11, one of the three surveyed seamounts, three camera tows were performed to observe the distribution of Fe-Mn crusts on the summit and slopes of the seamount. Although sediments of various thicknesses generally cover most of summit region of OSM11, several regions with high backscatter signals occur on the periphery of the summit. The occurrence of Fe-Mn crusts, observed during the camera tows, on those high backscattered regions suggests that the backscatter signals of shipboard multi-beam sonar can reflect changes in the geology of the seafloor from sediment layer to Fe-Mn crust deposits. The Fe-Mn crust deposited around the summit region is worthy of notice because of its topographic characteristics, including shallow depth, flat or gentle inclined surface, and smooth relief, which are more suitable for mining operation compared to the flanks of seamount."

Sep 1, 2014

By Michael J. Sapko, William D. Monaghan, Michael A. Trevits

Mine seals are used extensively in underground coal mines to segregate mined-out areas and to isolate fire zones or underground areas that are susceptible to spontaneous combustion. Over the years, 30,000 mine seals have been erected in underground coal mines in the United States. Mine seals, along with rock dusting and ventilation, represent the fundamental means of preventing underground coal mine explosions. In this study the National Institute for Occupational Safety and Health (NIOSH) used ground penetrating radar (GPR) technology to determine if each of three test mine seals were uniformly constructed. Three mine seals representing different construction methods and materials (cast-in-place foamed cement; solid block, polyurethane foam and gravel; and wire mesh, rebar and gunite) were erected at the NIOSH Lake Lynn Laboratory’s underground mine as part of an on-going research program. The seals were imaged using GPR with 400-, 500-, 900-, and 1,000-MHz antennas. We found that variations in uniformity existed in the material for the cast-in-place foamed cement seal. Variations in uniformity also existed in the seal made from solid block, polyurethane foam and gravel. The post-processed radar records correlated closely with recovered core samples (areas of gravel and polyurethane foam, and areas containing only polyurethane foam). Finally, the radar records of the seal made of wire mesh, rebar and gunite showed the various components. The results of this work suggest that GPR could be used as a tool to evaluate mine seal characteristics and construction uniformity.

By H. Tomlinson

"PURPOSE OF REPORTThe purpose of this report, which is the third of a. series on the coal mines of the Western States, is to give the findings of a study of the causes and methods of prevention of accidents from falls of root and coal in the mines of Lincoln County, Wyo. The three mines covered in this report, referred to as A. B. and C, account- for 9 per cent of the coal production in the county and nearly 9 per cent of the State's total production. For comparative purposes some statistical data are presented bearing upon the relation of injuries to their causes, to tonnage produced, to men employed, to days worked, and to days lost as the result of injuries.FATALITIES IN WYOMINGTo show the necessity for this study, Table 1 given the fatalities that occurred during 1928 in the bituminous—coal mines of the United States, of the State of Wyoming of Lincoln County, and in Mines A, B, and C, followed by a brief description of the Kemmerer coal dis-trict, its coal beds and immediate roof, thickness of cover, dip of coal beds, methods of mining timbering for roof support, roof testing, and supervision. All of these factors must be considered in any plan outlined to prevent accidents resulting from falls of roof and coal.ACKNOWLEDGMENTAcknowledgment is made to the officials of the operating companies for their cooperation and assistance during the study and collection of data to complete this report.GENERAL INFORMATIONLocation and Ownership The mines included in this report are within 18 miles north and south of Kemmerer, Lincoln County, Wyo. (fig. 1), and are owned and operated by various coal companies to supply the domestic, smelter and railroad markets. They are severed by branch lines of the Oregon Shorty Line Railroad Coal production and men employed underground in the three mines are indicated in essential detail in Table 2."

Sep 1, 1932

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By X. L. Huang

This paper deals with the experimental and theoretic study of the contact pressure beneath the deep foundation of Beijing International Hotel, The experiments have been carried out in project and in model footing 6.6m2. The result of measurements shows the contact pressure at the edge is greater than that at the center. The theoretic analysis on the base of elastic theorey is in good agreement with the test if the proposed assumption used.

Jan 1, 2010

By Gordon T. Clark, James R. Struthers, Celal Kirandag

INTRODUCTION Project Background The Washington State Department of Transportation (WSDOT) hired the Seattle office of Parsons Brinckerhoff to lead a team of consultants to produce an Environ-mental Impact Study and perform conceptual and preliminary engineering. The pur-pose of the Alaskan Way Viaduct and Seawall Replacement project is to replace the existing earthquake damaged and aging viaduct and sea wall, adjacent the downtown waterfront of Elliott Bay, with structures that have improved earthquake resistance and that maintain or improve mobility and accessibility for people and goods along the existing corridor. With an estimated replacement cost over $4 Billion and construction duration exceeding 8 years, it is one of the largest transportation design projects on the West Coast of the United States today. Seattle, Washington is a city of over 2 mil-lion people in the Northwest corner of the United States. Ever since the Klondike Gold Rush in 1897, Seattle has been considered a departure point to Alaska. Because of this, the street along the waterfront was named the Alaskan Way in 1930. Alaskan Way Viaduct and Seawall The Alaskan Way Viaduct (AWV) carries State Route 99 along the shoreline of Elliott Bay through downtown Seattle and is a vital part of Seattle’s highway system. The viaduct carries approximately 110,000 vehicles per day or 25% of all north-south traffic through Seattle (Figure 1). It is 3.4 km (2.1 mile) long with 3 lanes in each direction and was constructed of cast-in-place reinforced concrete between 1952 and 1956. The wear and tear of daily traffic, salty marine air, and several earthquakes have taken their toll on the facility. Studies in the mid-1990s provided early evidence that the viaduct was nearing the end of its useful life. The viaduct’s increasing age and vulnerability was apparent by crumbling and cracking concrete, exposed rebar, weakening column connections and deteriorating railings. In early 2001, a team of structural design and seismic experts began work to determine whether it was feasible and cost-effective to strengthen the viaduct by retro-fitting it. In the midst of this investigation, a 6.8 magnitude earthquake shook the Puget Sound region (the Nisqually Earthquake, located 56 km (35 miles) from Seattle and deep below the surface) caused moderate damage to the reinforced concrete structure. WSDOT closed the viaduct for inspection and repairs intermittently for several days over a period of several months.

Jan 1, 2007

By Yuanbo Zhang

Keywords: Complex Iron Ores, Roasting, Tin, Zinc, Pellets, Comprehensive Recovery. The complex iron ores containing tin, zinc are typical refractory ores. Large reserves of the ores are found in China and have not been utilized efficiently so far. A new process of tin and zinc recovery and pellet preparation from iron concentrate containing tin and zinc by controlled atmosphere roasting is developed in this investigation. The results of 2573 N/P compression strength of product pellets, the 91.49% and 82.22% volatilization of tin and zinc respectively, are achieved for a concentrate containing 0.39% tin and 0.28% zinc. The strength and chemical compositions of the pellets meet the requirement of blast furnace ironmaking. Volatilization mechanism of tin and zinc are investigated. Thermodynamic study shows that the reduction balance curves of SnO2(s) and SnO(g) are proximate in the presence of carbon, and the standard formation free enthalpy of FeO and SnO2 is also approachable. Therefore, it is difficult to realize the complete volatilization of tin in the form of SnO(g) by selective reduction. But SnO2(s) and SnO(g) will form SnCl4(g) or SnCl2(g) in the presence of chlorides and can be easily volatilized from the ores.

Jan 1, 2005

By Joel T. Werner

Tire costs represent one of the highest controllable costs in open-pit mining, accounting for approximately 10% of mining costs. Tire monitoring technology has evolved rapidly in recent years and is emerging as a viable tool for extending tire life and reducing costs. The majority of the major tire manufacturers and several independent companies are in various stages of developing monitoring systems that capture and store vital tire data. Previously this information had only been accessible when the vehicle passed a fixed point in the mine, or when mine personnel manually downloaded the data. Integrating this technology with a mine management system enables remote collection and management of trend and alarm data. Mine personnel can now monitor a tire?s health parameters at any time, anywhere on site, regardless of the vehicle?s location. Anomalous tire conditions can be detected early and corrective actions taken. This information can then be integrated with other major onboard systems, operating conditions, and geographical information. Tire monitoring no longer exists as a stand-alone technology, but has evolved into an important integrated tool for mine operators. This paper will review the current status and benefits of integrating this emerging technology with a real-time mine management system.

May 1, 2002

By M Hourn, D Turner, P Voigt, D Mallah

The GPM Gold Project is located in Armenia, and consists of an open cut mine at Zod, near the Azerbaijan border, and a CIL processing plant at Ararat near the Turkish border. Mining at Zod commenced in 1976, and focused on near surface oxide ores, which overlay deeper refractory sulphides. Historical mining has now almost depleted the oxide ores, and the sulphide content of ore delivered to the processing plant at Ararat is increasing. Gold and silver recoveries through the Ararat plant were declining steadily.GeoProMining, the owners of the project, have expanded the Ararat facility to deal with the increasing sulphide content in the ore. In 2014, GeoProMining refurbished an existing concentrator on site to recover a sulphide concentrate from the ore, and have constructed an Albion ProcessTM plant to oxidize the refractory concentrate. Glencore Technology (GT) provided the Albion ProcessTM plant as a technology package.In July 2014, the progress of the GPM Gold Project Albion ProcessTM Plant was reported (Hourn, Voigt and Turner, 2014). At the time of writing, the construction of the plant was nearly complete. This paper presents an update of project progress, covering commissioning and ramp up of the GPM Gold Project.The commissioning phase occurred over June to August 2014, which included an M3,000 IsaMillTM fine grinding plant, a 6 tph limestone milling plant, a 60 tpd vacuum pressure swing adsorption oxygen plant, a 10 m residue thickener and a 12 tph Albion ProcessTM oxidative leach plant. Since commissioning was completed, ramp up occurred over the following three months with downstream gold recoveries from cyanide leaching reaching over 98%.CITATION:Voigt, P, Hourn, M, Mallah, D and Turner, D, 2015. Commissioning and ramp-up of the Albion Process at the GPM Gold Project, in Proceedings MetPlant 2015, pp 207–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

S. R. Carter (Mount Isa Mines Ltd., Mt. Isa): I found many ideas to interest me in Haddon King's paper "Notes on Ore Occurrences in Highly Metamorphosed Precambrian Rocks" (Stillwell Anniversary Volume).At Mount Isa I have not been happy about some of the longstanding appreciations of the geological evidence as fresh data accumulated, and as more and more knowledge has been building up outside Mount Isa in recent years of sedimentary deposition of sulphides.Accordingly, I organized a small section of the Geological Department at Mount Isa at the beginning of 1958 under Senior Geologist, W. J. Murray to reappraise our geological record and investigate old interpretations and new ones that arise. The work is expected to take several years to complete, but it is hoped that sufficient will be done before then to permit the most plausible story on the ore genesis to be chosen. In the meantime, W. J. Murray has proposed, in a Company Report, that the.epigenetic features of the silver,lead-zinc deposits, which are essentially conformable with the shales, could have resulted from remobilized syngenetic deposits.Haddon King, on p. 159; has listed six assumptions that are required by a magmatic-hydrothermal theory of, origin for conformable deposits. It is interesting to consider the Mount Isa silver-lead-zinc deposits in terms of these requirements.My comments are listed in the same order as Haddon King's assumptions:(a) "The source of the constituents is magmatic and they have become available in successive waves of zinc-rich, lead rich, manganese rich, silver rich, etc, instalments in accord...

Jan 1, 1959

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

By Max F. Lee, Warren A. Peck

The applicability of the Q-system [Barton et al. 1974] to Australian underground metal mines is discussed with reference to two common design issues: ground support for horizontal mine development, and assessing the stability of bored raises. Installed ground support in mine development is com-pared to empirical estimates using the Q-system and associated support capacity calculations. Data are graphically presented from 59 specially selected sites at 15 contributing mines. The actual performance of large-diameter raise-bored shafts is also compared to empirical stability assessments using a modified version of Q (Qr, after McCracken and Stacey [1989]). Lower-bound Qr values are plotted against raise diameter for 47 selected sites at 23 mines in Australia and Papua New Guinea. The influence on Q and Qr of some geotechnical aspects of the Australian landscape, the dynamic nature of mines (compared to civil construction), and occupational health and safety regulations are discussed. Stability and support assessments that are based just on Q or Qr are not always conclusive. It is often necessary to consider other rock mass parameters, the regulatory environment, and risk issues. These results are interim; further data collection and analysis are required with regard to comparing actual performance versus empirical assessments.

Jan 5, 2007

By Wendy L. Naysmith

This paper deals with the various options considered and factors that influenced the final selection of the headframe, shaft layout and hoisting systems required at the Impala No 16 Shaft in order to hoist both the required 3 Mt of ore per annum, and transport men, material and equipment between the surface and the underground workings to a depth of 1640 m. The layout and construction method used for what is at present the world?s tallest concrete headframe is discussed together with the integrated hoist room foundations designed to suit multiple mechanical and electrical hoist supplier?s solutions. The mechanical components of the two tower mounted 6,5m 4 rope Koepe hoists and deflection sheaves and their layout is dealt with in detail. Various features of the bearing type, brake units and brake control system are also discussed. Installation of the mechanical and electrical hoist equipment in the headframe took place during the sinking phase of the project and placed severe restrictions on the use of the heavy lifting facilities. This required a well-managed and systematic approach to delivery of the hoist components and associated equipment, as well as close co-operation between all contractors on site.

Oct 1, 2010

The rock mass classification systems were developed for different functions, including support selection, excavation method selection and the determination of rock mass engineering properties for excavation design, among others. This explains in part why we have several rock mass classification systems. It is often cautioned that the rock mass classifications are to be used for preliminary excavation support design, but this caution is now often overlooked and detail/final support design based on the rock mass classification systems. This paper advocates differentiating between rock mass classification for pre-excavation support planning and rock mass classification for at-face excavation performance assessment. It is concluded that most at-face excavation performance problems are attributable to confusing the virgin rock mass rating with the rock mass rating on exposure during excavation, and that this observation is independent of the method of excavation. Procedures are then presented for virgin rock mass rating and for at-face rock mass rating/assessment during excavation.

May 1, 2009

By P Moswate, D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of gangue mineral grade limits by the concentrator may also result in significant penalties.Online grade analysers which can provide reliable real time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and has the benefit of operating in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades.MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at the BCL nickel concentrator plant in Botswana. The project focused on stabilising the final concentrate grade while ensuring the final tailings are minimised, resulting in an improved nickel recovery. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser. The positive results show the advantages of combining reliable real time measurements with an advanced process control system.CITATION:Mantsho, S M, Moswate, P, Strobos, P and Phillpotts, D, 2013. The implementation of floatstar grade-recovery optimisation control solutions using Blue Cube Online grade analysers on industrial flotation circuits, in Proceedings MetPlant 2013 , pp 575-582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013