Search Documents

By Lawrence G. Houk

Monazite sand is the only commercial source of cerium, other rare-earth metals and thorium. Although used in rather small quantities, it is essential to many industries. The United Unites is entirely dependent upon British India and Brazil for its supplies. Monazite sand or sand imported under the tariff classification for monazite was shipped to the United States in greater quantities, in 1940 than ever before. About 75 percent of our imports was from British India and most of the remainder from Brazil. If need be, Brazilian production can be expanded to supply all of our essential requirements, and the theater of war expands in the Pacific Brazil may supersede India as the principal source. PHYSICAL PROPERTIES The mineral monazite is generally honey yellow or may vary from greenish yellow to clove brown. The grains are small and resinous in luster, and range from subtranslucent to opaque. The specific gravity varies

Jan 1, 1943

By J. M. Singer

Methods are proposed for predicting concentrations of nitrogen oxides and carbon monoxide in the combustion gases of flames, specifically of lean, stoichiometric, and rich propane-air flames. Calculations are based on kinetic and thermodynamic theory. These theoretical data are compared with concentrations observed experimentally downstream of flat grid-type burner flames (approximately 25,000 Btu/hr) that were used to simulate gas appliances such as water and space heaters. Air pollutant concentrations are also computed for (1) flames chemically perturbed by recycling flue gases into the primary fuel-air mixtures; (2) flames thermally perturbed by cooling the burned gases at different rates; and (3) flames perturbed by combination of these two effects. In general, experimental and computed concentrations agree to within a factor of 2 to 7 with the experimental values always being higher than the theoretical. The theoretical analysis indicates that cooling the primary flame by recycling cold flue gases (with and without excess air) reduces the relative emission of nitric oxide and increases emission of carbon monoxide if the flame stoichiometry does not radically change. Cooling rates of about 5,500° to 10,000° R/sec starting at about 3,500° R generally suffice to prevent nitric oxide concentrations in lean flames from increasing much above the initial values at the combustion zone; these same cooling rates do not prevent oxidation of most of the initial carbon monoxide.

Jan 1, 1967

By AIME AIME

BLANDFORD. C. BURGESS, the new Chairman of the Industrial Minerals Division, took the advice of Horace Greeley in reverse-he turned his hack on San Francisco and the Golden Gate, and after a few side excursions toward Alaska and Arizona, hit the trail eastward, not for the lonesome pine, but for Spruce Pine, N. C. Born Aug. 10, 1893, in San Francisco. Burgess found his first job, shortly after finishing high school at 19, as axeman for a surveying party of engineers working for the Southern Pacific Co. in Oregon. Later he moved on up with them into Alaska. He liked the engineering profession, and decided to equip himself further so he entered the University of California in the fall of 1913. and for the next two years devoted himself to acquiring an education in civil engineering.

Jan 1, 1945

By Robert G. Bottge

The Bureau of Mines has engaged m a program to determine the availability of land for mineral exploration and development in Alaska. Land availability, based on ownership and Federal and State laws and policies, is compared with mineral terranes and mineral deposits. This is the fifth of six regional studies, which cover the State with a comprehensive set of maps and data compilations. This study covers an area of 112.3 million acres in western Alaska. In July 1986, 41.0 million acres, 37% of the study area, were available for mineral exploration and development; 14.6 million acres, 13%, were available with restrictions; and 56.7 million acres, 50%, were unavailable. Nearly 65% of the unavailable land is classified as national parks, preserves, wildlife refuges, and wild and scenic rivers. Of the 34.0 million acres of mineral terranes that underlie the study area, 12.9 million acres, 38%, are available for exploration and development; 3.6 million acres, 11%, are available with restrictions; and 17.5 million acres, 51%, are unavailable.

Jan 1, 1988

By W. L. Phillips

Nickel alloys containing approximately 0.5, 2.0, and 6.0 at. pct of Os, Pd, Ru, and Rh were Prepared by vacuum melting. Tension tests were carried out at 25°, 500°, 800°, and 1000°C; stress-rupture tests were carried out at 650° and 800°C. The room- and elevated-temperature tensile strength, as well as the stress-rupture life, increased for the same atomic percent in the order palladium, rhodium, ruthenium, osmium. The ductility decreased with increasing concentration or temperature for a given concentration. The results are discussed in terms of solid-solution theory. BOTH solid-solution strengthening and weakening have been observed in alloys. The simple rules which have been suggested to explain alloy strengthening are subject to several exceptions and deviations based on atom size and valency effects. The purpose of the present investigation was to extend the knowledge of the effect of solid-solution alloying on the mechanical properties of several Ni-Pt group metal alloys at room and elevated temperatures. The platinum group metals, osmium, ruthenium, rhodium, and palladium were chosen as the solute elements because of their different valencies and atom sizes. Nickel was chosen as the base material because of the large amount of previous literature available on nickel alloys. EXPERIMENTAL PROCEDURE Grade A Carbonyl nickel powder having the following composition: C, 0.07 pct; Fe, 0.013 pct; Mn, 0.0005 pct; Si, 0.016 pct; Mg, 0.0003 pct; S, 0.003 pct, was purchased from the International Nickel Co. The platinum-group metal powders were purchased from A. D. Mackay Co. The powders were weighed, cone-blended for 4 hr, and vacuum-melted into 1-in.-diam billets, approximately 2 in. long. The ingots were homogenized for 5 hr at 1800°F before being extruded into 1/4-in. rods at 2100°F. The alloy compositions are shown in Table I. Typical impurity values were not significantly different than that of the as-received nickel. All alloys were single phase. The lattice parameter of each alloy after the heat treatment described below is also included in Table I. Each alloy was annealed at 2200°F for 1 hr and air-quenched to comparable grain sizes (ASTM G.S. No. 4-5). The rods were then machined into test samples 0.160-in. diam and 0.750-in. gage length. Tension testing was carried out in an In-stron tension-testing machine at a strain rate of 0.02 in. per in. per min. An extensometer was used to determine the room-temperature yield stress. Stress-rupture testing was carried out in an Arc Weld stress-rupture unit. All testing was performed in air. EXPERIMENTAL RESULTS A) Room-Temperature Mechanical Properties. The 0.2 pct yield stress, ultimate tensile strength, and elongation for all alloys tested at room temperature are plotted as a function of atomic percent solute element in Fig. 1. The ultimate tensile strength for the same atomic percent increases in the order palladium, rhodium, ruthenium, osmium. The yield strength at low concentrations, -0.5 at. pct, increases in the order osmium, palladium, ruthenium, rhodium. At higher concentrations, 3.0 and 10.0 pct, the yield strength increases in the same order as the tensile strength. Both yield strength and tensile strength increase rapidly ini-

Jan 1, 1964

By D. B. Dreisinger, M. Rasouli

"Developing technology to address the environmental hazards associated with selenium in mine-impacted waters has been a serious challenge. Ion exchange (IX) has been identified as a potential treatment technology. This paper begins with a review on selenium adsorption with commercially-available basic anionic exchangers (BAS). It then looks at the use of resins for selenium removal via modification with the addition of -O, -N, or -S-containing chelating ligands and chelating polymeric ion exchangers pre-loaded with immobilized metal cations. The synthesis of chelating exchangers requires a final product with a highly stable metal in the ligand-metal complex. The nature, oxidation state, size, and affinity of the metal for the target oxyanions and the size, degree of protonation and space configuration of the oxyanion are among critical factors affecting the oxyanion uptake. There is a limited number of studies on the critical parameters affecting the selenium affinity for chelating exchangers. Such a study could fill in the gaps of our understanding of selenium-metal-chelating ligand interactions and assist in developing a new ion exchanger. In addition to commercial IX resins, layered double hydroxide materials (LDH) have received attention for oxyanion removal from waste water. The adsorption capacity of the LDHs are affected by the crystallinity of LDH, the nature of metal components, the ratio of metals, charge and type of anion, and the space between the layers. In particular, the Friedel phase (FP), a member of the LDH family, showed high adsorption capacity for selenate removal from synthetic solution. A study is currently underway at the University of British Columbia to investigate the effect of different synthesis methods and aging on the suitability of FP for selenium removal from mine waste water."

Jan 1, 2017

"Australia’s largest rail freight network operator, the Australian Rail Track Corporation (ARTC), has selected GE Transportation’s Movement Planner solution as the key technology enabler for its Hunter Valley-focused network control optimization program.ARTC’s Newcastle-based network control, is the nerve center of Hunter Valley rail operations, where locally based train control professionals make thousands of decisions every day to safely support the annual movement of more than 24 kt/h (26,400 stph) of freight, and tens of thousands of coal, freight, grain and passenger trains each year.ARTC plans to transform its train control function by integrating and then building on Movement Planner, an advanced software solution by GE Transportation that provides real-time rail traffic planning and optimization to enable freight to move more efficiently. “The Hunter Valley rail network is one of the busiest and most complex in the country, supporting the largest coal export port in the world,” ARTC managing director and chief executive officer John Fullerton said.“As bulk freight demands grow, rail operators like ARTC and supply chains like the Hunter Valley coal network need to be creative in the way they respond so the Australian economy doesn’t miss out. That’s why we have conducted a worldwide search to find globally proven solutions that will improve our network productivity and efficiency,” Fullerton said.The Movement Planner solution considers multiple factors including train schedules, trafficcontrol systems and train movements relative to each other and then develops an optimized traffic plan for the trains throughout the network. Existing GE customers have benefited from increased visibility of network operations, higher velocity, less dwell times, and improved on-time performance across their networks."

Jan 1, 2018

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By A. J. Kauffman

This study compiles data on the zircon resources of the Pacific Northwest States, Alaska, and California, to determine the productive capability of industrial concerns to make ductile zirconium and hafnium, and to investigate markets for the nonmetallic products of zircon. West coast zircon resources are large but mostly marginal to submarginal. Development of a stable and profitable zircon mining industry on the west coast will depend upon recovery and utilization of the other associated heavy minerals needed by regional and national markets. The west coast has the only completely integrated facility for processing zircon sand to reactor-grade zirconium and hafnium and for making fabricated products from these metals. The future of the zirconium metal industry appears to be good because of increased use of the metal for nuclear propulsion and power-generating plants.

Jan 1, 1965

By Kilmar Mine

The Kilmar dolomitic magnesite deposit~ in sourhwesr Quebec lie in Grenville Province sedimentary rocks that strike north and dip steeply west. The sediments comprise quartzitic, carbonate and argillaceous members. The middle or carbonate member hosts the magnesite and, like the two other members, has been intensely mewmorphosed. Magnesite occurs as lenticular shaped zones of altered limestone and is mixed with 5 to 30% dolomite crystals. Diopside, serpentine and mica are common accessory minerals. Magnesite appears to have formed from merasomarism of all or part of the carbonate member due to intrusion of hot magnesia-rich solutions. Magnesite is mined from a 490 m vertical shaf1 and is milled and burned into clinkers, which then are shipped 10 pyroprocessing industries around the world.

Jan 1, 1984

By Andrea Brickey, JUDITH BUABA, RICHARD AMOAKO

The global mining industry has recorded significant declines in accident and injury rates attributed to the advancement in technology, increased enforcement, and safety consciousness. A goal of the mining industry is to achieve zero injury and occupational illness on all mine sites, prompting increased research into ways to further reduce mine accidents. A machine learning technique known as multiclass logistic regression is applied on a 10-year injury dataset from the Mine Safety and Health Administration (MSHA) to determine a miner’s susceptibility to a class of injury and to help identify significant risk factors associated with different classes of injury. The data is aggregated based on injury classification to provide statistically relevant results. The analysis identifies specific risk factors that influence a mine worker’s susceptibility to a given class of injury, i.e., non-fatal with no days lost or restricted activity, non-fatal with days lost and/or days of restricted work activity, and fatal and total permanent or partial permanent disability. These factors include miner’s age, mine type (coal vs. non-coal), experience on the current job (years), shift start time, employment type (operator vs. contractor), mining district, and type of accident. The results of the analysis indicate that a miner’s experience on the job, i.e., the number of years worked in a current job, is a significant risk to injury occurrence, even for those with decades of total mining experience. We further show the differences and similarities between the surface and underground mine incidents.

Nov 3, 2020

By Aleksandar N. Nikoloski, Rorie Gilligan

Brannerite, UTi2O6, is the most common of the refractory uranium minerals and requires leaching under intense conditions to effectively extract the uranium contained within. Brannerite is often found together with apatite in metasomatic uranium deposits. Apatite and other phosphate gangue minerals can inhibit uranium leaching by generating phosphate ions which interfere with the reactions between acidic ferric sulphate and uranium minerals. As part of a detailed fundamental study on the leaching reaction mechanisms for brannerite, tests under a range of selected leach conditions were carried out with the addition of 10 g/L fluorapatite with the goal of identifying conditions where the negative effects of phosphate are reduced. Leaching was carried out for 5 hours with 0.05 mol/L Fe3+ as Fe2(SO4)3 with 0.25–1.00 mol/L H2SO4 and at temperatures between 25 and 96 °C. A single test was performed with 0.05 mol/L Fe3+ as FeCl3 and 1.00 mol/L HCl. In the sulphate system, the effect of phosphate was weakest at the highest acid concentration (1.00 mol/L H2SO4). In the chloride system, phosphate did not suppress uranium extraction, suggesting that HCl leaching could be a viable alternative for the leaching of high-phosphate refractory uranium ores.

Mar 17, 2021

By Adam Powell, Salvador Barriga, Matthew Earlam

"The inert anode is a key enabling technology for dramatic energy and emissions reduction in extractive metallurgy. In molten salts, the materials challenge is nearly insurmountable: the anode must conduct electrons at high temperature in a pure oxygen and molten salt environment. A solid electrolyte, e.g. zirconia, between the salt and anode removes the molten salt stability constraint, and can act as a container for a liquid metal anode. This can be liquid silver for oxygen-generating inert anodes, or several metals for natural gas-fueled anodes; it is possible to switch between these modes. The solid electrolyte brings several other benefits: it eliminates molten salt contamination of the anode gas, creates a reducing environment enabling low-cost steel vessels, increases current efficiency, and eliminates carbon contamination of the product. New developments presented here, including current collector and low-cost anode designs, amplify these benefits for producing aluminum, magnesium, rare-earths, and other metals.IntroductionReactive metals such as magnesium, aluminum and rare-earths play increasing roles in efficient transportation and clean energy. In response to new fuel economy standards, automotive OEMs are planning large increases in use of aluminum and magnesium to reduce vehicle weight. Rareearth permanent magnet motors and generators exhibit better power-to-weight and efficiency than induction motors and other designs, making this today's primary motor technology for hybrid and electric vehicles, and for wind turbines. Nickel metal hydride (NiMH) batteries with lanthanum are dominant in hybrids. In 2011, transportation comprised 28.6 out of 103.1 EJ of US energy consumption [1] and 1,845 out of 5,471 million metric tonnes (MMT = 109 kg) CO2e of US greenhouse gas (GHG) emissions [1], creating big targets for economy-wide reductions.Unfortunately processes for making reactive metals for these applications are very inefficient and heavily-polluting. In primary aluminum production, Hall-Heroult cell electricity use [2] is more than double the reaction enthalpy due to heat losses through frozen cryolite side-walls and anode gases, graphite anode plants add significant energy use and GHG emissions [2] (see Table 1). Magnesium is even worse: silicothermic reduction by the Pidgeon process in China produces about 85% of the world's magnesium using coal or coke gas [3]. Chloride electrolysis begins with high-purity MgO and requires carbochlorination or hydrochlorination and costly chloride dehydration [4]—rendered unnecessary for aluminum by the Hall-Heroult cell. Production of neodymium and lanthanum with graphite anodes leads to inconsistent carbon content: small cells make 1 kg batches for analysis, sorting and sale by carbon content, with very high labor and analysis costs. And vertical electrodes give no incentive to reduce anode effect: some reports indicate that China's rare-earth metal industry emits more CF4 and C2F6—with global warming potential (GWP) 6500 and 9200 times CO2 respectively—than China's aluminum industry [5]."

Jan 1, 2014

By Hans Lundberg

Introduction Today, geophysical exploration is recognized as a special science wedged between geology and mining. Universities and technical institutes have special professors teaching geophysics applied to oil and ore prospecting. The list of literature on geophysical exploration has grown from practically nothing at all some twenty-five years ago to ~ several thousands of books, some of them very imposing volumes. Most of the methods now used have been developed since the first World War, and very large systematic exploration campaigns have been carried out in many places, in many countries. It has been rather difficult to obtain enough information as to what is going on in Canada. However, since the Associate Committee on Geodesy and Geophysics of the National Research Council became more actively engaged in promoting geophysical research, it may be easier to obtain information and, in the future, the quarterly issued Canadian Geophysical Bulletin may throw considerable light on the current geophysical activities in Canada. Some twenty crews have been engaged the last few years in geophysical prospecting for ore. In the United States, between 500 and 600 crews are employed exclusively in geophysical prospecting. Most of these, however, are engaged in oil exploration. During the winter 1942-1943, the German Government employed some fifty crews on geophysical exploration, and some ten crews were working for private enterprises.

Jan 1, 1948

By M J. Nugus, F Clark, E J. Hill, J T. Carswell, J S. Cleverley, N H. S Oliver

High-nugget gold orebodies are difficult to model in 3D because samples from diamond drill core are generally too small to provide reliable estimates of the gold content of the larger body of rock, and therefore interpolation of gold assay values between drill holes is also unreliable. As a result, gold resources are generally underestimated in areas of high nugget. In practice, proxies for gold mineralisation, such as presence of alteration, specific structures or high vein density, have been used by geologists to predict rocks which are favourable for mineralisation. However, there has been no automated method for combining the predictive capabilities of several proxies, except by human judgement.We have been developing a method to combine several different types of geological features or geochemical analyses into a single measure using conditional probability. Conditional probability provides a meaningful numerical measure for the favourability of rocks for containing high-grade gold mineralisation. This measure can be interpolated in the exploration space, providing a sound basis for a 3D model of the orebody. We have developed this technique using data from the Sunrise Dam Gold Mine, which is a high-nugget orebody hosted in a structurally complex Archaean greenstone belt and which has historically proved to be a very challenging orebody to model.CITATION:Hill, E J, Nugus, M J, Clark, F, Oliver, N H S, Cleverley, J S and Carswell, J T, 2013. Predictive three-dimensional modelling of nuggety gold orebodies, Sunrise Dam, Western Australia, in Proceedings World Gold 2013 , pp 463-468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Charles Prasky

This report describes and appraises recent progress in the development of a differential sulfatizing process for recovering a ferrograde manganese oxide from low-grade manganiferous ferruginous materials in the Cuyuna range. Individual process steps were carried out successfully using a 20-inch-diameter shaft for continuous countercurrent sulfatization of the manganese, a multiple-compartment rotary drum for leaching the water-soluble manganese sulfate, a submerged-combustion evaporator for the recovery of monohydrate crystals of manganese sulfate, and a shaft furnace for the thermal decomposition of sulfate crystals for production of a ferrograde manganese oxide and a sulfur dioxide gas suitable for sulfatization of fresh are. Of the two general kinds of Cuyuna manganiferous materials--the carbonate slates and the oxidized ores--only the slates were studied at pilot scale.

Jan 1, 1963

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

This study presents a method for recovering valuable metals and synthesizing anhydrite from steel slag using sulfuric acid leaching and solvent extraction. The process achieved high leaching efficiencies for V, Ti, Fe, and Mg, and produced anhydrite with 93.09% purity. The leachate was further processed to separate and recover V, Ti, Fe, and Mg using selective stripping and precipitation methods, offering a sustainable approach to steel slag utilization.

Jan 22, 2022

By Mauk JL, Arehart GB

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulfide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3%o in 618Oq,,,,,= between maximum and minimum isotopic values for the deposit. Significant overlap in 618Oqu,, values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981

By Sumit Kumar Hota, Asadi Srinivasa Reddy, Ashok Kumar, Ashish Agrawal, Surajit Sinha, Chandra Sekhar, Tanay Ray

In the current operational facility, due to the absence of pellet pot facility, a novel technique is developed wherein the pellets with different chemistries prepared in the laboratory are fired in an induration machine by placing them inside the Inconel baskets. In the present work, an attempt is made to optimize the pellet chemistry by developing 2 different flux pellets, viz., low basicity (B2: CaO/ SiO2 = 0.3) pellets and high basicity (B2 = 0.9) pellets, and further the effects of basicity on pellet properties, viz., cold compressive strength, porosity, swelling index, reducibility index, and softening and melting temperature, are studied. It has been found through the multiple operational trials that increasing the basicity of pellets from 0.3 to 0.9 results into improving the pellet strength, reducibility and softening and melting characteristics. Moreover, it is observed that the swelling index of pellets is reduced by adding 2% MgO to both low and high basicity pellets that could be attributed to the formation of high melting point slag in pellets. The operational trial has resulted into producing pellets that exhibit a combination of desired mechanical strength, improved swelling, and reducibility index and possess better softening–melting behavior among all the chemistries studied.

May 24, 2022