Search Documents

By J. W. Howland

To determine their effectiveness in different climate and soil conditions, a demonstration of dozer blades specifically designed for recontouring mine spoil was conducted at an East Texas surface coal mine. The specialized equipment included a 48-foot angle blade, a modified 24-foot "U" blade, a 13-foot deep "U" blade, and a 24-foot grading bar. Both the 4b-foot and the 24-foot "U" blades were mounted in a two-tractor, single-operator configuration. To meet flotation problems common in this mining region, a 22-foot lightweight blade was developed and demonstrated for use on a 400-430 hp tractor. The demonstration involved 1,185 acres and showed a 50% reduction in reclamation costs and a 47% reduction in fuel requirements for this mine site over conventional equipment. Improved equipment, trained operators, good supervision, and improved monitoring techniques contributed to the savings. Procedures and results of the demonstration are presented and analyzed here along with guidelines for application of findings.

Jan 1, 1981

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuO0.5- CaO-MgO-FeOwAIOl.s?SiO2) slags were calculated. The log (Po2/PS2) versus matte grades of various industrial processes was determined. The PoiPS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By Robert H. Merrill, James V. Williamson, David M. Ropchan, George H. Kruse

In- situ rock stresses were determined by flatjack and borehole - deformation methods . Estimates of the stress distribution around a flatjack were obtained by a combination of flatjack and borehole - gage techniques . The investigations were part of a study , conducted jointly by the State of California and the Federal Bureau of Mines , to determine the stress in rock at the site of an underground powerplant for the Oroville Dam near Oroville , California . The stress distribution around each of three flatjacks was nonsymmetric ; however , stresses obtained from 9 flatjack and 157 borehole measurements are considered reasonably accurate for engineering purposes . The stress near the edge of the openings is between 800 and 1,600 psi ; the stress in the undisturbed rock is approximately 500 psi , nearly hydrostatic .

Jan 1, 1964

Jan 1, 1942

By Jian-guang Yang, Lei Jie, Si-yao Peng, Jian-ying Yang

A new membrane electrolysis process for bismuth recovery from bismuthinite concentrate was introduced. Under the conditions of temperature 70 degrees C, acidity 3 mol/L, solid liquid ratio 1:4 and 1.1 times stoichiometry sodium chlorate dosage for 1.5 h oxidation leaching, more than 98.5% bismuth can be leached from bismuthinite concentrate. The resultant leach solution was subjected to membrane electrolysis. Under the conditions of NaCl concentration 300 g/L and pH 7 in anolyte, bismuth ions concentration 80 g/L and HCl concentration 3 mol/L in catholyte, heteropole distance 6 cm, temperature 40 degrees C and current density 200 A/m2, a flat deposited bismuth plate can be obtained after 24 h electrolysis, and the bismuth purity was more than 99%. The current efficiency of cathode was 97.88%. Chemical component analysis results showed that the average convert efficiency of the sodium chlorate was 52.77% and the average oxidizing efficiency of chloride ion was 69.78%, and the resultant anolyte generated in anode compartment could be fully reused as oxidant for leaching bismuthinite concentrate again.

Mar 1, 2017

By D. Harrington

The record of fatalities from mine explosions during the past 2 fiscal years has been anything but encouraging; more men were killed by explosions (379) than were killed from the ante cause during to' preceding 6 years combined (368). The reason for the large increase in the number of explosion fatalities during the past 2 years as compared with the previous 6 years is not entirely clear. In some instances, there has been laxity in the enforcement of State mining laws; in others, both workers and operating officials is have failed to observe recognized precautionary measures to prevent explosions. In many of the explosions that lave occurred within the asst few years in mechanized mines it has been evident that speed of operation and a demand for maximum tonnage at minimum cost resulted in neglect of ordinary safety measures.

Jan 1, 1942

By J. A. Kost

A dust-control manual was prepared for use by mine operations personnel. The manual documents state-of-the-art control techniques, dust sampling, and use of personal protective devices. Content addresses advantages/disadvantages of control techniques, design and operating specifications, and implementation and maintenance guidelines. An indexed list of selected references is also included. In addition to the completed manual, this report documents work performed in the course of its preparation.

Jan 1, 1981

By George R. Schottler

The objective of this research is to find the extent of the range of applicability of previously developed statistical methods for determining grade and tonnage of ore to bedded uranium deposits. Uranium assays obtained from gamma-ray logs of exploratory drill holes are used to compute grade and tonnage of ore in the deposit by a standard polygonal method and by statistical analysis. The results obtained by the two methods are compared. The uranium-assay frequency distributions are shown to be lognormal and a simple transformation permits the use of standard normal curve statistics. The effects on the assay frequency distributions of stratified sampling, a required minimum mining thickness, and increased assay-interval length are investigated. The addition of low-grade mineralization to make up the required minimum mining thickness results in a distinct change in the skewness of the assay frequency distribution. Any statistical inference regarding grade-tonnage relationships that will be produced, using the minimum mining thickness, should be made on the basis of this "revised" assay frequency distribution.

Jan 1, 1965

By A Trench, S Ulrich, S Hagemann

A synthesis of reported All-In Sustaining Costs (AISC) for 57 Australian gold mines in the period 2014–2016 reveals for the first time the clear influence of grade upon cost performance, most evident in gold-only underground mines. Past syntheses of costs on a single quarter basis have viewed grade as potentially subordinate to other factors such as production scale, mine geometry, mineralisation style and a combination of other mining-related costs. Better understanding of the grade to cost relationship on both an individual mine and whole-of-portfolio portfolio basis is needed. Insight into the roles and trade-offs between other cost-determining factors will aid the future sustainability of the gold mining sector in Australia and assist in targeting prospects for future resource growth and development. While the overall trend is toward higher-grade mines displaying lower costs and vice versa, the grade to cost functions appear radically different between mines based on time-series data. The median cost of Australian gold production in the final quarter of 2016 was A$1081/oz. The threshold for lowest cost quartile production was A$965/oz. Underground production now dominates Australian gold output – with 71 per cent of ounces originating from operations that are either entirely underground or hybrid pit/underground mines. Scale economies are evident, with smaller mines predominately among the higher cost producers. For mines of equal grade, open pit mines are lower cost than underground operations. Reserves are modest, with a median mine life for underground operations of 4.7 years based on current production rates. Reserve additions at mines are likely constrained not only by the finite nature of mineralisation at each mine but also by the geometrical difficulty of accessing suitable drilling locations to test for reserve extensions.CITATION:Ulrich, S, Trench, A and Hagemann, S, 2017. Towards an understanding of production costs at Australia’s underground gold mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Milton E. Jennings

On May 11, 1977, the SAMARCO 20-inch, 396-kilometer (246-mile) Pipeline was placed in service. This system represents the latest thinking in slurry pipeline design and is one of the main contributors to the viability of the SAMARCO Project. This paper presents the background, description and latest information on the system's operation. Special attention is given to the handling limitations of the slurry and to the unique hardware requirements.

Jan 1, 1978

By Scott W. Hazen

This report describes exploration for lead-zinc ores at the Madonna mine between 1945 and 1953 by the Utze Lode Co., the Bureau of Mines, and the company with Government financial aid under the Defense Production Act of 1950. The Madonna mine yielded silver, lead, and zinc with a net smelter value of over $5,000.000. from 1882 to 1924. The mine was inactive from 1924 to 1942 when the Utze Lode Co. acquired the property. Possibilities for finding ore in the mine, especially at depth, were considered favorable. The Utze Lode Co. began rehabilitating the Madonna mine in 1945. An exploration program, which consisted of winze sinking and drifting, failed to produce commercial are.

Jan 1, 1956

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two-thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By R B. Wanty

Historically, most investigations of biogeochemical cycling in acid rock drainage systems involved synoptic sampling over longer time periods (one sample per week or month) or intensive time series studies over a few hours or days. However, many important episodic loading events, such as seasonal meltwater and storm events occur on timescales that are rarely observed by these traditional sampling approaches. Monitoring these transient processes, which may contribute the bulk of the annual metal loading, is essential for accurate assessment in acid rock drainage areas. Recent work also has demonstrated dramatic diel (24 hour cycle) variations in trace metal concentrations in response to diel changes in temperature, pH, oxygen, and photochemical cycling (Brick and Moore, 1996; Nimick et al, in prep). To characterise a system that may respond to diel, seasonal, and episodic events, a monitoring program must sample at a frequency that captures the details of these major forcing events. We developed two novel instruments, the Zn-DigiScan and the DigiSampler to examine low and high frequency temporal changes in acid rock drainage areas. The Zn-DigiScan is a battery powered real time in situ chemical analyser designed for long-term deployments with hourly analyses of Zn. Stream physical parameters (temperature, conductivity, dissolved oxygen, pH, turbidity, etc) were measured every 15 minutes with a water quality sonde. The DigiSampler was developed for the long-term daily sampling of biogeochemically active elements and can take either discrete samples or samples integrated over 24 hours. The DigiSampler collects 2 ml samples in a Teflon coil which are separated by 0.2 ml nitrogen bubbles. The sample coil is returned to lab and the 2 ml samples are diluted 1:10 and analysed for trace metals by ICP-MS. Initial results from a three-day deployment at Fisher Creek, MT, USA have successfully demonstrated the ability of the Zn-DigiScan to record Zn concentrations at levels below 100 ¦g/L. Zinc concentrations measured at 30 minute intervals in Fisher Creek showed a diel cycle with low values of ~25 ¦g/L in the late afternoon and increasing to ~60 ¦g/L by early morning. Zn concentrations were inversely related to temperature and pH, suggesting that temperature and pH dependent adsorption was the main factor controlling diel Zn fluctuations. Initial deployment of the DigiSampler also was successful, revealing diel cycles in Zn, Cu, and Mn. Comparison of trace metal samples collected by the DigiSampler showed good agreement with samples collected by an Isco automated water sampler, demonstrating that the DigiSampler can collect clean samples for trace metal analysis at the low ¦g/L range.

Jan 1, 2003

By Pedro Jorge Walburga Keglevich de Buzin

A qualificação das sucatas ferrosas e beneficiamento por moinhos shredder são operações utilizadas pelas usinas semi-integradas com objetivo da melhoria na produtividade e qualidade do aço produzido. Um benefício adicional é a redução de impurezas e a melhoria da qualidade ambiental desta matéria-prima. Neste trabalho é avaliada a influência da qualidade da sucata no teor de cloro e de metais residuais em poeiras de aciaria elétrica provenientes de três usinas semi-integradas, com diferentes perfis de produção. Os resuItados alcançados mostraram uma possível redução do teor de cloro de cerca de 50% com a utilização de sucata processada por shredder. Os menores níveis de cloro potencializam a aplicação posterior de métodos para adequação do teor de cloro, favoráveis à reciclagem, incorporação ou coprocessamento destas poeiras.

Oct 30, 2017

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing mischmetal (MM), cobalt, copper, magnesium, and iron for use in permanent magnets in place of the scarce samarium-cobalt alloys. The magnetic properties of MM-Co, MM-Co-Cu, MM-Co-Cu-Mg, and MM-Co-Cu-Fe-Mg alloys were evaluated. Magnets were fabricated by powder metallurgy consisting of arc-melting the metals, crushing and grinding the resultant alloys, alining and compacting the powder, and sintering the compacts. Magnetic values of MHc = 4.7 kOe, BHc = 4.07 kOe, Br = 6.81 kG, and (BH)max = 10.0 MGOe were obtained with a MM-Co alloy containing 36±0.5 wt-pct MM. By substituting copper and magnesium for part of the cobalt, the values for MHc and BHc were increased to 29.0 kOe and 5.89 kOe, respectively. This intrinsic coercivity value exceeded that of Sm-Co alloy obtained in our laboratory. The addition of iron to MM-Co-Cu-Mg alloys resulted in an increase of Br to 6.90 kG and (BH)max to 10.3 MGOe. Copper and magnesium contents of these alloys were optimized to obtain maximum values of MHc.

Jan 1, 1981

By Y. B. He

The effect of the stability and rheological properties of magnetite dense medium on the separation performance of a 6" dense medium cyclone (DMC) is studied with the use of fine density tracers. The tests in which different size fractions of magnetite are used to prepare the dense media reveal that at low medium densities (<1.5 s.g.), the best separation is achieved when using the magnetite with intermediate particle sizes (du3.2=18 11m). At medium densities above 1.5 s.g., however, it is beneficial to use coarser magnetite. With the fine magnetite dense medium, an increase in medium density results in a decrease in separation efficiency. With the coarse magnetite, an opposite trend is observed; the separation efficiency is improved with increasing medium density. An accurate cutpoint control is critical in gravity separation. The cutpoint shift for coarse feed particles is found to decrease with increasing medium stability (density). It assumes values close to zero in a highly stable fine dense medium. When the size of the treated particles is small (<0.5 mm), the cutpoint shift is mainly determined by medium rheology. With increasing medium density, a continuous increase in cutpoint shift is observed.

Jan 1, 1993

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 27th August, 1969, at 4.15 p.m. Mr. R. C. J. Goode (President) was in the Chair. There were also present seventy Members, ten As¬sociate Members, two Affiliates, one Student and twelve Visitors making a total of ninety-five. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: "It is my very sad duty to announce the deaths of the following members of the Institute: Mr James Charles Napoleon Humphreys, a Life Member who joined the Institute on 1st April, 1935, and passed away on 6th February, 1969. Mr Michael John Worrall, Graduate Member, who joined the Institute in 1960 and passed away on 2nd June, 1969. Mr Eric Adam Conrad Dickson, Associate Member, who joined the Institute on 13th June, 1952 and who passed away on 8th June, 1969. Mr Robert Jack, Associate Member, who joined the Institute on 2nd August, 1956, and passed away on 14th June, 1969. Mr R. A. H. Flugge-de-Smidt, Honorary Life Member and Gold Medallist, who joined the Institute in 1922 and passed away on 17th June, 1969. Mr John Gordon Craig, a Member who joined the Institute on 23rd August, 1960, and passed away on 6th August, 1969. As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, I would ask you to rise and observe a few moments silence." MINUTES The President: "May we confirm the Minutes of the General Meeting held on 18th June, 1969, as published in the July, 1969, issue of the Journal?"-Agreed. WELCOME TO VISITORS The President: "We are honoured this afternoon by the presence of the Institute&apos;s Honorary President, Mr R. S. Cooke, President of the Chamber of Mines of South Africa, and by one of our Honorary Vice-Presidents, Mr T. L. Gibbs, the Government Mining Engineer, as well as by the presence of many distinguished guests, to all of whom I extend a most cordial welcome. We are happy to have present, Mr S. C. M. Naude, Director of the Witwatersrand Technical College, Mr G. A. P. Louw, Vice-President of the Associated Scientific and Technical Societies, Mr R. P. Randall, Senior Vice-President of the South African Institute of Electrical Engineers, Mr W. T. L. Wayman, President of the South African Institution of Mechanical Engineers, Mr D. F. Odendaal, President of the Institution of Certificated Mechanical and Electrical Engineers of South Africa, Mr E. Haacke, President of the Institute of Land Surveyors of the Transvaal, Mr B. L. Loffell, Vice-President of the South African Institution of Civil Engineers, Mr J. F. Leatherbarrow, President of the South African Institute of Assayers and Analysts, Dr W. S. Rapson, President of the Joint Council of the South African Scientific Societies, Dr P. L. Carman, President of the South African Chemical Institute, Mr F. Jackson, President of the Federation of Societies of Professional Engineers, Mr W. E. Kirkwood, President, S.E.I.F.S.A., Mr J. Steele, President of the South African Institute of Foundrymen, Mr M. Waite, President of the South African Institution of Welding, Mr M. R. Gericke, President of the South African Council of Professional Engineers, Mr G. C. Sowry, Chairman, Witbank-Middelburg Branch, Mr T. Groenewald, Chairman of the South African Chemical Institute (Southern Transvaal Section), Professor O. B. Volckman, Chairman of the South African Institution of Chemical Engineers, Mr H. W. Le Roux, Chairman of the South African Federation of University Engineer¬ing Students, Dr R. E. Robinson, Director of the National Institute for Metallurgy, Mr P. H. Anderson, Deputy-Chairman of Rand Mines Limited, Mr E. Boden, Manager of the A.S. and T.S. and Count Folchi-Vici, from Italy, who has lime interests in this country. I also extend a very special welcome to the lady guests here this afternoon, and to all the visitors." MEMBERSHIP The President: "I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Members: Stuart Denston Hill, Robert Roy Richardson, Gert Paulus van der Vyver. Affiliates: Henry Clifford Read, Allen Edward Hooper, Alan Edwin Edkins. Graduates: Lester Winston Sturgess, Erroll Vincent Bosman. Students: Terence Vernon van Heerden, David Curtis Lindley. MEMBERS TRANSFERRED TO A HIGHER GRADE From Associate Member to Member: Andries Willem van Zyl, Roy Lardner, Nugent Gerald Ward Comyn. From Student to Graduate: Michael John Worrell (now passed away), Peter John Hamilton Short. I wish to welcome the new members to the Institute, and to congratulate those members who have been transferred to a higher grade." ANNUAL REPORT OF THE COUNCIL AND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1969 The President: "Ladies and gentlemen, It is with much pleasure that I present to you the Annual Report and Accounts for the year ended 30th June, 1969. These have been laid on the chairs and before calling for their adoption I would like to make a few comments. The Accounts show an excess of expenditure over income of R2,124 and our Honorary Treasurer, Mr D. G. Maxwell, will in due course comment on this. The main difficulty has again been the cost of the Journal and I think most of you are aware of the changes that we propose to make. I shall be sorry to see the last of our old format but then I have always had rather a con¬servative outlook.

By A. Tewarson

Combustibility data are presented for 14 samples representing commonly used mine materials (treated and untreated wood, conveyor belt and brattice cloth). The combustibility data were obtained in the Factory Mutual Small-Scale Combustibility Apparatus (sample area -0.008 m ). The hazards associated with the mine materials were evaluated in terms of: 1) ignition/ surface flame spread using an ignition parameter (IP). A reasonable correlation was found between IP values and U.S. Bureau of Mines ratings for conveyor belts and brattice cloth and large-scale fire test data for treated and untreated timber sets; 2) generation of combustible vapors, using a vapor generation parameter (VP); 3) heat release using a heat generation parameter (HP). A reasonable correlation was found between HP values and the large-scale fire test data for treated and untreated timber sets; 4) generation of "smoke," toxic and corrosive products using a chemical compound generation parameter (CP); and 5) light obscuration by "smoke" using the light obscuration parameter (LP). All the wood treatments, except Fireguard, were found to be effective in reducing the fire hazard. The effectiveness of the treatment appears to be due to enhancement of carbon formation in the solid phase and enhancement of water formation in the vapor phase. Concepts are presented for establishing 1) the relationship between various parameters (IP, VP, HP, CP, and LP) and basic properties of materials, and 2) the usefulness of the parameters as criteria for the combustibility and fire hazard evaluations of the mine materials.

Jan 1, 1982

By John F. Papp

The objective of this U.S. Bureau of Mines study is to calculate an accurate, reliable estimate of chromium and nickel content of stainless and heat-resisting steel produced in the United States. The columbium, manganese, molybdenum, titanium, tungsten, and vanadium contents of this steel are also calculated. Such contents are required for estimating the quantity of alloying element recovered from recycled stainless steel and consumed by market sectors. In this investigation, the elemental fraction of stainless and heat-resisting steel was calculated as the ratio of the weight of element contained in stainless steel to the weight of stainless steel produced. The elemental fraction has been calculated as a time-averaged, grade-averaged value. The elemental fraction was averaged from 1962 through 1983, and averaged over the grades for which production was reported by the American Iron and Steel Institute during that time period. The 1962-83 average elemental fraction of U.S.-produced stainless and heat-resisting steel was calculated for chromium to be about 0.17 ± 0.01; columbium, 0.00014 ± 0.00003; manganese, 0.015 ± 0.005; molybdenum, 0.004 ± 0.001; nickel, 0.07 ± 0.01; silicon, 0.009 ± 0.001; titanium, 0.0004 ± 0.0001; tungsten, 0.0001±0.00003; and vanadium, 0.00003±0.0000l.

Jan 1, 1991

By Grano S. R, Ralston J

It is the perennial problem most metallurgists face when examining data collected from laboratory float tests and plant surveys - there are more numbers than we know what to do with! The objective of this paper is to analyse and interpret a set

Jan 1, 1994