Search Documents

Vertical retreat open stoping (VROS) is a variation of sublevel open stoping (SLOS) that has been introduced at Cannington to minimise the influence of subvertical geological structures during stope extraction. The first application of VROS is described, where structures within the stope resulted in a change in firing sequence and the extraction of two complete sublevels in a single blast. The use of electronic detonators is critical to the success of VROS and their application is described. Numerous benefits of using VROS have been identified and are described. To date, eight stopes have been successfully mined using VROS. In addition to the first application of VROS, two further case studies are described.

Jan 1, 2005

By J. C. Stankus

Many coal seams are associated with soft floor strata and during mine development if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One of the methods for controlling floor heave is floor bolting. This paper describes the demonstration of floor bolting methods in a West Virginia coal mine. Three methods were used: (1) vertical full resin bolting, (2) floor truss bolting, and (3) floor truss bolting plus a floor cut at the center of the entry. The design of each method and the experimental results are discussed in detail.

Jan 1, 1993

By R. W. Michelson

The Bureau of Mines developed computerized mathematical models to estimate the economic availability of Mesabi Range taconite concentrates; these are a quality model, a cost model, and an economic availability model. The quality model evaluates metallurgical test data; the cost model determines iron unit cost from mining and processing cost data; and the economic availability model determines quantity from geologic and ore quality data. By correlating all of the physical resource quality factors and dimensional characteristics with the economic cost factors associated with producing iron ore pellets, these three models combine to establish a final relation between iron ore reserve quantities and iron unit cost.

Jan 1, 1970

By GEORGE D. RAMSAY

WHEN the Ironton blast furnace of the Columbia Steel , Co. was first put into operation the iron ore was mined frol11 the deposit near Iron Springs, Utah. This is principally a hematite with 12 to 20 per cent of magnetite finely disseminated throughout the ore. It varies from a fairly soft broken rock structure to that which is hard and compact. In the broken form it will weigh about 150 lb. per cu. ft., and in place the density is approximately 250 lb. per cu. ft. The first ore received for the blast furnace was crushed so as to pass through approximately a 4-in. square opening screen. A typical screen test of this ore is shown in Table 1.

Jan 1, 1935

By H. Polat, Q. Hu, M. Polat, S. Chander

"The electrostatic charge on spray droplets of ionic surfactant solutions and coal particles was measured and the results were correlated with the dust collection efficiency. When various surfactant were added, the magnitude of the droplet charge increased significantly and it was observed to be a function of surfactant type and concentration. The concentration of maximum droplet charge coincided with surfactant concentration where maximum collection efficiency was observed for these surfactants. Particles of coal also carried substantial amount of charge magnitude of which seemed to be a function of coal rank.Based on the results presented in this paper, it was concluded that ionic surfactant primarily act as a strong electrostatic charge inducer for droplets. Due to interactions between these highly charged droplets and naturally charged particles, the efficiency of droplet-particle collisions play a primary role when compared to the wetting and engulfment phenomenon which could only follow a successful collision. INTRODUCTIONWater spray are widely used to suppress airborne dust in mine atmospheres (Walton and Woolcock, 1960; Kobrick, 1970; Hamilton, 1974; Jayaraman et al., 1986). Several investigators have considered the use of surfactants to enhance the effectiveness of water sprays especially for difficult to wet particles such as those of coal (Glanville and Wightman, 1979). The capture of dust particles by water droplets involves droplet-particle collisions, adhesion of particles to droplets, and engulfment of particles into droplets. Surfactants affect these sub processes through their influence on droplet charge, surface tension, and wetting. The last two mechanism have been thoroughly studied in recent years (Walker et al., 1952; Cohen and Rosen, 1981; Glenville and Haley, 1982; Chander et al., 1988; 1991). However, little attention has been paid to the role of electrical charge on particles and droplets on the collision and adhesion of spray droplets and dust particles."

Nov 1, 1995

By Ronald J. Riberich

The Mineral Economics and Management Society (MEMS) held its fifth annual conference in Montreal, Quebec, Canada earlier this year. “The Minerals Industry: Responding to the Global Challenge” was the first MEMS conference to be held outside of the United States. About 125 mining- and minerals-related professionals attended. The MEMS program included six sessions and three distinguished speaker addresses. The session topics included: “Minerals in the Macro economy: Development in Demand,” “Trends in Global Metals Supply: The Producers’ Challenge,” “Global Environmental Issues: Policy Perspectives,” “Global Environmental Issues: Quantitative Analysis” and “Minerals in the CIS: Phoenix or Albatross?” A student session was also offered. It provided a competition for monetary awards for outstanding papers.

Jan 1, 1996

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

By J. J. Jakosky, D. H. Zellers

"IntroductionThis paper is the seventh of a series describing an investigation being conducted by the Bureau of Mines on underground communication. A review of past work and results obtained has been published. The present paper deals with a study of line-radio or wired-wireless methods of communication, herein electrical energy is transmitted by metallic conductors.The use of line-radio over metallic conductors has been practiced for a number of years, and at present is being used on a large scale in long-distance carrier-current telephone and telegraph. The early work of the U. S. Army Signal Corps and the Bureau of Standards in using ordinary radio transmitting and receiving apparatus for communication over metallic conductors was been descried. Later publications describe commercial applications, and an excellent treatise and resume is given by E. Colpitts and C. B. Blackwell.Scope of ReportThis report contains (1) a discussion of the chief factors affecting carrier-current transmission, with particular reference in application to underground communication for mines; (2) a description of typical underground circuits used for power and lighting; and (3) description of apparatus used and results obtained in line-radio experiments in coal mines near Pittsburgh, with circuit diagrams, and conclusions as to power requirements and limitations for mine use."

Apr 1, 1925

By Arno C. Fieldner, J. W. Paul, WALTER A. SELVIG

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the quality and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition. and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines,July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.' Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.2 Descriptions and analyses of samples collected during the fiscal years 1913 to 1916 were published in Bureau of Mines Bulletin 123.3 The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1916 to 1919. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22, 85, and ,123, the same plan of geographical classi- fication has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1922

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

By A. Mehmet

The feasibility of employing a multi-stage column for the recovery of gold from cyanided pulps using extruded carbon was investigated on a pilot-plant scale. It was anticipated that the column contactor would have certain advantages over conventional carbon-in-pulp plants. The feed pulp was screened to remove particles larger than 200 µm and was diluted to a solids concentration of about 23 per cent. The column was operated continuously for 24 days at a pulp flowrate of about 60 l/min and a carbon flowrate of 44 litres per day. The average gold concentrations in the barren pulp 12 hours and 24 hours after the carbon transfer were 0,012 and 0,031 mg/l respectively. The average gold concentration in the solution phase in the feed was about 2,0 mg/L. The average gold Loading on the carbon was 6290 g/t. Calcium carbonate was removed from the loaded carbon by treatment with 0,5 bed volumes of 2,8 per cent hydrochloric acid solution at ambient temperature. The calcium concentration was reduced from about 17 000 to about 500 g/t The carbon was eluted by the Zadra procedure at atmospheric pressure. The results of the elution were highly satisfactory, the gold concentration being reduced from about 6000 to about 20 g/t in 48 hours. The eluted carbon was regenerated in a Rintoul kiln at about 700°C. The activity of the regenerated carbon was found to be at least as high as that of fresh carbon.

Jan 1, 1992

By P Gehrke, S O’Gorman

The precise measurement of NO2 was historically difficult in road tunnels, hence criteria and design analysis was based on converting from NOx concentrations via a set NO2:NOx ratio. The reliable direct measurement of NO2 is now possible, however design analysis is still dominated by emissions tables and formulas specified in terms of NOx. For converting from NOx to NO2 in a road tunnel environment in Australia, the ratio has typically been assumed to be ten?per?cent. This has generally been based on the recommendation in PIARC (2000) and on the ‘average’ value cited in PIARC (1995).Determining this ratio is important as changes in engine technology and in-tunnel pollution criteria along with improvements in CO and particulate emissions control, may mean that NO2 will become the driving factor for future ventilation requirements. Correct selection of this ratio can directly impact the ventilation capacity and system design.Recent research has indicated that choosing a constant ratio of ten?per?cent for all tunnels may not be appropriate. The in-tunnel ratio has been estimated to be as much as 20?per?cent to 30?per?cent and depends on the location in the tunnel, the type of ventilation system and the traffic/fleet characteristics. This paper discusses the effect of some of these parameters on the NO2:NOx ratio in road tunnels.The findings indicate that the ten?per?cent upper limit on the NO2:NOx ratio in PIARC (2000) may be a conservative value for design purposes for longitudinally ventilated road tunnels of typical length in Australia. A value of seven?per?cent to eight?per?cent may be more appropriate in some circumstances. However, the value chosen will depend on the specific tunnel in question and the confidence in traffic conditions expected. Values above ten?per?cent may be encountered for short periods but usually when the NO2 levels are low.CITATION:O’Gorman, S and Gehrke, P, 2014. NO2:NOx ratios in Australian road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By LeRoy R. Curwick

This Bureau of Mines report presents the results of a study conducted to assess the domestic availability of chromium from superalloy and cast heat- and corrosion-resistant alloy scrap material. Six alloy classes included in this survey were investment cast, hardfacing, and wrought nickel- and cobalt-base alloys, wrought nickel-iron-base alloys, and heat- and corrosion-resistant alloy castings. Data were collected for 1976 on metallic scrap generation, use patterns, and production practices for these alloy producing and using industries. A model was developed that allowed an assessment of the materials flow circuits within the industries that produce these alloys. The types, amounts, sources, secondary products, and ultimate destinations of chromium- containing metallic scrap for the six alloy classes were determined. Regarding the overall recycling efficiency of these alloy producing and using industries, of the 580.9 million pounds of scrap generated from these six alloy classes in 1976, about 72 percent (416.8 million pounds) was remelted by the same alloy-producing industries, about 18 percent (104.9 million pounds) was downgraded into stainless and low-alloy steels, about 3 percent (19.7 million pounds) was exported, and about 7 percent (39.5 million pounds) was lost through landfill or other disposal or service wastage. The lost material is primarily contaminated oxides for which recovery is currently uneconomic. However, the 124.6 million pounds of scrap material downgraded or exported in 197b contained potentially recoverable critical strategic elements. The amount of scrap material lost to the six alloy-producing industries in this manner contained 22.1 million pounds of chromium, 53.4 million pounds of nickel, 5.9 million pounds of cobalt, 35.9 million pounds of iron, and 7.3 million pounds of other alloying elements.

Jan 1, 1980

By Xie Zhang, Jiang Diao, Xin Qiu, Lu Jiang, Bing Xie, Hong-Yi Li

"Duplex converter process, in which the first converter is used for removing phosphorus from hot metal (De-P), is an important way to produce low P-content and ultra-low P-content steels. In order to improve phosphorization removal and formation of slag with high basicity at relatively low temperature during dephosphorization converter process, effects of temperature, silicon content in hot metal and varied compositions of the De-P converter slag on phosphorus distribution between the slag and hot metal were investigated with thermodynamic calculations and by laboratory scale experiments in present work. Results showed that phosphorus distribution ratio between slag and metal was varied in 10.6~26.6 when basicity of the slag was in the range of 1.5~2.1 at 1370, and the distribution ratio was increased with increasing basicity and Fe10 content in the slag.IntroductionIt is known that phosphorus exists in steel in the form of solid solution, which can significantly improve strength and hardness of steel at room temperature. However, the plasticity and toughness of steel, especially the low temperature plasticity is sharply reduced and leads to high ductile-brittle transition temperature. This phenomenon is commonly known as cold brittleness of steel [1~3]. Hence, phosphorus should be removed as much as possible in the steelmaking process, because it is generally harmful to the iron and steel products."

Jan 1, 2013

By Joseph Grumer

The range of composition of gases synthesized from solid fuels which are exchangeable with natural gas on current gas appliances was evaluated by theoretical principles. These principles consider primarily the flashback, blowoff, and yellow-tipping characteristics of air-entraining burner flames. It was found that complete identity between the synthetic and natural product is not necessary. Gases such as may be obtained by hydrogasification of coal and other solid fuels without the removal of unreacted hydrogen offer advantages in flame characteristics. Between 25 to 37 percent hydrogen can be tolerated in the sendout gas.

Jan 1, 1965

By Siwiec A

The laboratory investigations which are necessary to evaluate the mineral processing effectiveness usually include density separation of narrow size fraction of the feed and one of the products. In each size - density fractions the content of valuable mineral has to be determined. These data and yield in each size - density fraction can be specified by a matrix of partition coefficients. They are counterparts of recoveries. These coefficients can be compared with the mean recoveries at each density or size fraction or the total recovery, to determine which density - size fractions are processed in the best or worst way. The basic categories are: vector of metal content l _i 1711, 7t2, òòò, ltM I ò vector of particle size distribution x = I d1, d2, ..., dN I ò matrix of partition coefficients P11, P12, Pi N P _ P21, P22, ..., P2 N PM1 PM2..., PMN These three conceptions allow one to determine all the basic metallurgical parameters of a mineral processing unit. Losses of valuable mineral are connected with: ò mineralogical composition of the ore (types of minerals, their properties, dissemination, crystallochemical affinity, type and properties of gangue minerals), ò applied technology and technical equipment (beneficiation as a stochastic process, processing methods, process control, intergrowth liberation, water quality). Examples of application of the analytical method proposed are given for zinc - lead and coal processing plants.

Jan 1, 1993

By A. G. Loomis

METHODS for measuring relative permeability as a valid function of saturation were compared by the. Bureau of Mines, using core samples from representative oil-productive California formations, from the Bartlesville sand in Oklahoma, and from synthetic samples. Measurements for gas-oil systems were made by steady-state dynamic, unsteady-state displacement and two stationary-phase methods. Measurements for water-oil systems were made by the unsteady-state displacement method. As the ratio rather than individual relative permeabilities is measured by the last method, three methods for calculating individual relative permeabilites from their measured ratio were compared for gas-oil systems and two methods for water-oil systems. Errors arising from capillary discontinuities, such as the end effect and stabilized-zone flow, are discussed and evaluated; possible errors rocs arising from turbulant flow are also examined. The inapplicability of non-steady-state methods for water-oil systems that are not definitely oil-wet is discussed in detail. Measurements of relative permeability to both gas and oil can be made quickly and accurately by the steady-state dynamic method when rates of flow of the two phases are sufficient to minimize the capillary discontinuity at the outflow end of the sample. At such rates relative permeability-saturation measurements are essentially independent of the rate of flow. The steady-state method wits modified by a dispersion section at the inflow end of the sample acid designated tie dispersed-feed method.

Jan 1, 1962

By David R. Lentz

At True Hill in southwestern New Brunswick, low-grade porphyry-style Bi-8n-Mo greisen mineralization is associated with the cupola of an epizonal granite porphyry (granite) that also exhibits three episodes of brecciation. The first episode of brecciation is an in situ, 8 m to 10 m wide transitional zone of net-veined to coarse-grained "blocky" endogranitic mesobreccia that is chloritized and greisenized and hosts weak disseminated minerali.zation. In a zone closer to the host rockgranite contact, angular fine- to coarse-grained endogranitic mesobreccia with greisenized matrix is superimposed on the earlier transitional breccia. The latest episode is fault-controlled and consists of quartz- and chalcedony-hosted sub-angular to rounded fine-grained "pebble" mesobreccias that crosscut and brecciate the other breccia types, as well as the adjacent altered metasedimentary country rocks. The first two episodes of brecciation are magmatic-hydrothermal in origin related to hydrofracturing of the granite carapace and are accompanied by greisenization and mineralization, whereas the post-mineralization, silica-hosted, "pebble" mesobreccias related to hydromagmatic, low-temperature fluid circulation and/or boiling along faults near the contact. These magrnatichydrothermal and hydromagrnatic mesobreccias are similar to those associated with W-Mo-Bi porphyry-greisen mineralization at the Mount Pleasant deposit.

Jan 1, 1994

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By R. W. Geehan

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Bureau engineers made a preliminary examination of the Morefield mine early in 1943 and recommended investigation by trenching and diamond drilling, The Bureau of Mines conducted work from August to December of 1943, which indicated that the Morefield mine was a favorable location for an experimental mining program. The Bureau of Mines carried on such a program from September 1947 to March 1949. The property investigated is 30 miles southwest of Richmond in Amelia County, Va. (fig. 1). During World War II mica and beryl were shipped from the Morefield mine, but after the high prices and premiums paid during the war years were not available the mine was closed.

Jan 1, 1953