Search Documents

The pilot scale testing of Australian coals for their NO, emissions was carried out at the ACTC to investigate the influence of coal properties, furnace conditions and different NO,, control strategies on NO,, emissions. The NOx emissions for the Australian coals tested were found to vary over a wide range and primarily depended on combustion temperature and excess oxygen conditions. These coals did not exhibit any fundamental difference in NOx levels to other world coals. Under similar combustion conditions, the conversion of coal nitrogen to NO. was found to be best correlated with coal rank parameter, R, max per centage. The use of staged combustion as a control strategy was shown to reduce their NOx levels by 56 - 77 per cent.

Jan 1, 1991

By J. A. Pile, Virgil Miller, R. G. Peterson, F. B. Petermann

"INTRODUCTION As virtually no published data are available on the sintering of fine, minus-100-mesh, ferrograde manganese ores, it is most opportune to present data on the amenability of various fine ores and mill products to the sintering process. These data cover the sintering or nodulizing of finely crushed, high-grade pyrolusite and rhodochrosite ores, sintering of manganese carbonate flotation concentrate, sintering or nodulizing the calcine from the deleading of a manganese oxide flotation concentrate, and sintering the calcines made in a Herreshoff furnace from the treatment of manganese sulfate products.If finely sized products are to be smelted in the present electric or blast ferromanganese furnaces, they must be sintered or nodulized. The only specification as to the size of the sintered or nodulized product is that it must pass a 6-inch screen and not contain over 1t-1/2 percent minus 20-mesh material. The minimum-maximum size has not been established. Undoubtedly this opti mum size will be set by the ferromanganese industry when ample quantities of manganese oxide sinters have been smelted."

Mar 1, 1942

By Ray J. Holmquist

"INTRODUCTION At the request of Elmer Burch, of Taos, N. Mex., the Apache mica mine was examined by an engineer of the Bureau of Mines in October 1942. As the result of this examination, the Bureau of Mines proposed to extend an adit to the projection of the mica-bearing dike. The Federal Geological Survey then prepared a topographic and geologic map of the property. This information and consultations with members of the Survey 3/ assisted in determining the course and extent of the exploratory work. The author supervised the work, which was done from January to May 1944.Title to the property was in litigation during the period of the Bureau of Mines investigation. Conrad Johnson, of La Madera, N. Mex., was contesting the valley of Burch's claim location covering the Apache mine. Johnson was a prior claimant. A map made during mining operations prior to 1929, showing all mine workings, was in the possession of Johnson, but he would not produce it for inspection as long as his title to the property was in doubt. The course of the adit extension was therefore controlled by the best information and judgment otherwise obtainable."

Mar 1, 1947

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18' API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

By David M. Rempe

The purpose of this standard is to provide a method for testing of cushion materials that leads to uniform results when employed by various organizations and laboratories. The load-deflection characteristics measured using this method are intended to provide input data for analysis of pile driving, as in wave equation analysis of pile driving. It should be recognized, however, that there are several factors which may cause a difference in performance between the test samples under laboratory conditions and actual cushion materials under pile driving conditions. These factors include variations in material properties from sample to sample, compaction and/or deterioration of the materials with use, eccentric loading due to misalignment, confinement effects or the cushion container or inter layered materials, head buildup, rate of loading, etc. In order to obtain representative load-deflection characteristics, therefore, testing of cushion specimens which have been subjected to actual pile driving conditions is encouraged 1 such specimen should be tested at various stages of the useful life of the cushion. The users of the data are cautioned to determine if the particular wave equation program they are using requires either the secant or tangent definition of the stiffness and modulus of elasticity.

Dec 1, 1984

This paper explores the use of a Process Safety Management (PSM) system to manage risk in the mineral processing and metallurgical refining industries. Important elements of a PSM system are described. International regulations and non-regulatory guidelines covering PSM for high hazard industries are reviewed. Case studies of incidents in the mineral processing and metallurgical refining industries are presented to understand the lessons learned from failure to manage risks using a PSM system. Conclusions are drawn to adopt PSM in the minerals and metals processing industry as a tool for loss prevention and risk management.

Jan 1, 2003

By Juan Daniel Martínez, Janaina Accordi Junkes, Dachamir Hotza, Tatiana Pineda

"The rice husk combustion in a bubbling and atmospheric fluidized bed reactor was investigated. The results showed the technical viability of producing both heat and amorphous silica from a renewable energy source. This paper presents the characterization of rice husk ash (RHA) obtained under varying fluidization velocities (0.13-0.15 m/s) and rice husk feed (4.5-7.2 kg/h). Characterization techniques include X-ray fluorescence, X-ray diffraction, particle size distribution and scanning electron microscopy. For the employed range of fluidization velocities of rice husk feed no noticeable influence on the chemical composition of produced RHA was observed. After combustion, RHA containing ~93% amorphous silica and <3% unburned char was obtained. RHA primary particles presented sizes from 90 to 100 µm and a tendency for agglomeration in aqueous media. Thus, the potential of this type of reactors with respect to speed, continuity and self-sufficiency energy of the process was shown.IntroductionDue to the increase of the agroindustrial production, the concern with processing by-products, such as rice husk (RH), is growing. For a better material and energy use, allowing a cleaner production and a more maintainable development, RH can be used as renewable fuel in the production plant, for instance, in steam generators. The adequate combustion of RH generates hot gases with low levels of pollutants, as carbon monoxide and particulate material.RH is the protecting coating formed during the growth of the rice grain, composed by four structural layers.1 The main components of the husk are cellulose and hemicelulose (50%) besides lignine (26%) and organic components (4%), as oils and proteins. The remaining amount includes inorganic materials (SiO2, Al2O3, K2O, Na2O, MgO, CaO, Fe2O3, MnO, P2O5).1The rice husk ash (RHA) is the product of the termochemical transformation of RH. The conditions of the different conversion processes (pyrolysis, gasification and/or combustion) determine the physical-chemical characteristics of the final product. RHA corresponds to 14 to 25% RH, depending on the variety of the rice, climate and soil of the producing area.2-4 The main component of RHA, which is generated at moderate combustion temperatures, is amorphous silica (SiO2) in the range from 80 to 97%.4,5"

Jan 1, 2008

By R. E. Siemens, Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites . The process consists of four mmaajjoorr steps : ( 1 ) reduction roast , ( 2 ) ammoniacal leach , ( 3 ) solvent extraction , and ( 4 ) electrowinning . Several solid - liquid separation steps are required that affect the economics of the overall process . In this study , two techniques for solid - liquid separation , centrifugation and thickening , were investigated . This report presents the results of ( 1 ) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and ( 2 ) an economic study of the two techniques , based on the requirements of a commercial - size ( 5,000 - tpd ) laterite processing plant . Sizing and other equipment - related recommendations , based on data from the Bureau's studies , were obtained from commercial manufacturers . The costs of thickening and centrifugation , including all the unit operations affected , were determined by the Bureau's process evaluation group . The total operating costs for separation using the two techniques ( including depreciation on the capital cost of equipment ) were found to be quite close : $ 17.26 per ton of laterite for centrifugation and $ 18.15 per ton of laterite for thickening . For centrifugal separation , the greatest cost was found to be the initial capital cost for the separation equipment ; using thickeners , the greatest cost was for reagent recovery .

Jan 1, 1983

By B Small

CSA Mine, named after the nationalities of the mines first owners being Cornish, Scottish, Australian, is one of Australia’s deepest and highest-grade copper mines. A combination of the modified Avoca method and shrinking was a standard practice where production rings were fired against and bogged to waste fill. This method resulted in dilution and involved rehandling of waste material to refill the bogged stopes in the Western region and the QTS Central. The introduction of pre-charging blastholes using a wireless initiating system (WebGen™) has enabled CSA to design and fire stopes in reverse. This involves the use of a pre-charged Temporary Rib Pillar (TRP) against the waste fill material in a previously mined stope. The temporary pillar reduces dilution and improves conventional bogging as material is blasted towards the drawpoint rather than towards the waste fill material. Additional drill, prep and blast re-work is reduced or completely removed as rings can be charged prior to, in conjunction with, or after, charging of the slot. This is a safer practice as the charge crew spend no time working adjacent to a brow or open void. A TRP trial was conducted in the western orebody at CSA. The risk of exposure to a brow or open void while charging underground, and the bogger rehandling of waste material was successfully eliminated. Once reverse stoping was established in modified avoca stopes at CSA, two TRPs were implemented in challenging ground conditions in the QTS Central region. The TRPs were utilised in a retreating four-way intersection to extract a central diminishing pillar to close the level out. The ore recovered in this stope provided 5 per cent of CSA’s copper for the year. Without pre-charging with a wireless initiating system, two 5 m pillars totalling 6936 t of ore at 7 per cent either side of the stope would not have been recovered. CSA has implemented the practice of reverse stoping in modified avoca stopes using TRP for ten stopes since the successful trial. The development of additional blasting techniques enabled by precharging with wireless initiating systems is currently underway in the QTS North orebody at CSA Mine.

Mar 29, 2023

By L. H. Banning

Recent dry-top electric smelting tests at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., indicate that a high-titanium slag and a good grade of pig iron can be produced from alluvial Idaho ilmenite. A total of 120 tons of concentrates were smelted during this investigation, to yield an average of 0.5 ton of slag and 0.3 ton of pig iron per ton of ilmenite. Power consumption averaged 1,400 kv.-hr. per ton of ilmenite, at a feed rate of 400 to 500 pounds per hour, when operating at an electrical energy input of 290 to 370 kilowatts. The optimum operating voltage appeared to be 110 volts, phase-to-phase. Graphite electrode consumption averaged 15.6 pounds per ton of ilmenite smelted. Magnesite furnace refractory withstood the corrosive action of the hot metal and slag better than carbon refractory.

Jan 1, 1955

By Peter Fischer, Heinz-Jiirgen Kateloe, Anton Sroka, Axel Preusse

"Since mining in Germany has a long history, there are still many locations where the surface fracture problem has to be solved. Shallow mine workings from an earlier era can affect the surface in a discontinuous way. In many cases, due to light overburden load, those mine rooms did not collapse and a downfall can suddenly happen for many reasons, e.g., in connection with a changed load entry into the subsurface or by additional influence of water. This results in ground movements, which in extreme cases, appear as surface fractures.Depending on the use of the surface, ground movements caused in such a way constitute an endangerment by law. Particularly, within the southern Ruhr district, surface fracture and subsidence endangered ranges are determined on the basis of an empirical method that resulted from a systematic evaluation of surface fractures and rock disclosures. This method indicates maximum ranges within which impacts from abandoned shallow mine workings must be assumed.With a special emphasis on a risk management approach, RWTH Aachen University adapted the model of stochastic media to the conditions of abandoned shallow mining to compute and illustrate potential ground movements due to the collapse of shallow mine workings. Further investigations were concerned with the analysis of characteristic parameters which can serve for the assessment of the surface fracture probability in a comparative view of different cases. In recent years, more than 50 surface fractures in the southern Ruhr district were analyzed in order to develop a risk assessment of surface fracture endangered ranges over shallow mine workings. The results that have been obtained so far are described in this paper.INTRODUCTIONAbandoned underground mine workings of shallow depth can pose a threat to the surface. Due to small overburden rock loads, shallow excavations often remain intact for decades after the operations have ceased and may collapse abruptly (Braemer et al., 2005; Hollmann and Nuerenberg, 1972; Preusse et al., 2007). Several approaches for prognosis of surface fracture resulting from 97 subsurface collapse deal with this topic (Loebel and Sroka, 2001; Tajdus and Sroka, 2009)."

Jan 1, 2010

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

Jan 1, 2001

By John Griffen

This paper records over twenty years&apos; experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years&apos; experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By John Griffen

This paper records over twenty years&apos; experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years&apos; experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By J. H. Maysilles

The Bureau of Mines is conducting research on various technologies to recover alumina from domestic resources for feedstock to existing aluminum smelting capacity as a means to reduce dependence on imported bauxite, which represents 93 pct of U.S. aluminum requirements. One of the more promising technologies being investigated is the hydrochloric acid leaching of kaolinitic clay. In the hydrochloric acid leaching technology, alumina is recovered from iron-free aluminum chloride leach liquor and separated from impurity elements by sparging the liquor with HC1 gas to crystallize aluminum chloride hexahydrate (ACH). A large-scale crystallizer with a 336-gallon usable volume was constructed and operated to obtain engineering and design data for potential scale up and to demonstrate the ability of the technology to produce specification grade alumina. Test campaigns involving about 1,400 hours of operation were completed. ACH meeting all chemical purity requirements could not be produced by a single crystallization, but was produced by recrystallizing the product from the calcined kaolin clay leach liquor. Product crystals with a size distribution of more than 80 pct plus 100 mesh and 65 pct plus 65 mesh were made at a rate of 10 pounds of ACH/(hr)(ft3). The zirconium tube heat exchanger used to maintain constant process temperature operated with an over-all heat transfer coefficient of 420 to 500 BTU/(hr)(ft2)(°F).

Jan 1, 1981

By Thomas F. Anderson

(Measurements of stable isotopic variations (sulfur, carbon, and oxygen), supplemented by chemical, mineralogical, and petrographic analyses have been used to investigate the processes responsible for : (1) the incorporation of sulfur in coal, and (2) the (development of permineralized peat zones ("coal balls"). Sulfur isotopic results indicate that there are two principal sources of sulfur in the Pennsylvanian coals from the Illinois Basin: (1) "primary" sulfur assimilated by plants (low-sulfur coals), and (2) "secondary" sulfur produced by reactions involving H2S that was produced by the anaerobic reduction of sulfate in seawater which permeated the peat during post-depositional marine transgressions (the dominant source of sulfur in high-sulfur coals). Sulfur isotopic compositions of low-sulfur coals in Several Tertiary basins of Wyoming are consistent with a plant sulfur source. However, the inverse correlation between content and isotopic composition of sulfur observed in coals from the Powder River Basin suggest some "secondary" additions to these low-sulfur coals. Seveeral Quaternary (freshwater pears which were submerged by sea-Level rises during deglaciation over the past 30 ka have sulfur contents and isotopic compositions similar to high-sulfur coals. Carbon and oxygen isotopic compositions of calcareous coal balls from North America and Europe suggest that (1) the carbonate was derived from variable proportions of oxidized plant matter (typically predominant) and inorganic carbonate, and (2) the carbonate minerals were precipitated from fresh-to-brackish waters. Local geochemical and hydrological conditions were apparently more important than regional depositional environments in controlling the source of carbonate and the development of coal balls.

Jan 1, 1983

No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world&apos;s supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of "boom" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.

Jan 1, 1925

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites. The process consists of four major steps: (1) reduction roast, (2) ammoniacal leach, (3) solvent extraction, and (4) electrowinning. Several solid-liquid separation steps are required that affect the economics of the overall pro-cess. In this study, two techniques for solid-liquid separation, centrifugation and thickening, were investigated. This report presents the results of (1) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and (2) an economic study of the two techniques, based on the requirements of a commercial-size (5,OOO-tpd) laterite processing plant. Sizing and other equipment-related recommendations, based on data from the Bureau&apos;s studies, were obtained from commercial manufacturers. The costs of thickening and centrifugation, including all the unit operations affected, were determined by the Bureau&apos;s process evaluation group. The total operating costs ~or separation using the two techniques (including depreciation on the capital cost of equipment) were found to be quite close: $17.26 per ton of laterite for centrifugation and $18.15 per ton of laterite for thickening. For centrifugal separation, the greatest cost was found to be the initial capital cost for the separation equipment; using thickeners, the greatest cost was for re-agent recovery.

Jan 1, 1984

By John D. Foulkes, David A. Curtis, Robert L. Lagace, John L. Rothery

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal mines. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to deter- mine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m5 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to be attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977