Search Documents

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is con-?ned by tectonic shear zones between marble and metapelites, extending laterally into the marble astabular, pod or lenticular oreshoots (up to 50 m x 20 m x 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical pro?les across mineralized zones con?rm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the in-situ supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly in?uenced by seasonal ?uctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent ?ooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2~10-3.8 to 10-1.4) and oxygenated (fO2~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sul?des and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+was transportedinto karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Abstract-Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is confined by tectonic shear zones between marble and metapelites, extending laterally into the marble as tabular, pod or lenticular oreshoots (up to 50 m ?? 20 m ?? 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical profiles across mineralized zones confirm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the insitu supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly influenced by seasonal fluctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent flooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2 ~10-3.8 to 10-1.4) and oxygenated (fO2 ~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sulfides and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+ was transported into karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2 in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2 increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Zhen He, Deqing Zhu

"In this paper, the reduction kinetics of low grade hematite ore was calculated. Mineralogy shows that the ROM (run of mine) ore is of low grade hematite ore type, assaying 27.2 wt% Fetotal and with main valuable minerals of hematite. The reduction kinetics shows that the reduction reaction rates of pellets with additive and without additive are all controlled by diffusion through the product layer. The calculated apparent activation energy of pellets with 12 wt% complex additive is 8.55 KJ/mol, dropping 62.23% compared to that of pellets without additive.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 620 million ton in 2010[1]. Therefore, large quantities of low grade iron resources are necessary to utilize in China at the moment. During the past years, extensive research has been carried out on the low grade hematite ores [2-6], such as reverse floatation, gravity separation, high-gradient magnetic separation and direct reduction-magnetic separation. Direct reduction-magnetic separation is an innovation way to treat the low grade hematite [7]. However, the research of reduction kinetics of low grade hematite is few. Some research about the reduction kinetics of reducing iron oxides by CO was studied [8]. The results indicated that the apparent activation energy is 8.0-28 KJ/mol when the reducing reaction is controlled by internal diffusion. The apparent activation energy is 50-75 KJ/mol when the reducing reaction is controlled by chemical reaction. In this paper, the reduction kinetics of pellets was also been studied."

Jan 1, 2012

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977

By L. L. Godirilwe, and A. Shibayama, G. Danha, K. Haga, Y. Takasaki

Selective extraction through leaching of an amorphous slag obtained from a base metal smelter plant in Botswana is investigated in this paper, where the main objective is to optimise the experimental variables that would result in the maximum selective extraction of the three base metals (Ni, Cu and Co) from the slag waste. Mineralogical tests showed that the sample is composed mainly of fayalite (Fe2SiO4), with a total entrapped metal sulphides content of about 1.0 wt.% occurring as fine occlusions in the fayalite phase. In our experimental program, we compare the effectiveness of two common leaching techniques. In the first method, we use sulphuric acid to carry out atmospheric beaker leaching tests, and in the second method we use high pressure oxidative leaching. The effects of acid concentration, oxidant addition/oxygen partial pressure and pulp density on metal dissolution rate are examined. The optimal Ni, Cu, Co extractions of 80.5%, 81.9 and 98% respectively were obtained under high pressure oxidative leaching conditions (150 oC, 0.6 M H2SO4, 0.5 MPa O2), with substantially low dissolved Fe of 9.6%, the majority of which was removed as jarosite in the residue. Atmospheric beaker leaching yielded poor extractions of Ni below 40% when sulphuric acid combined with hydrogen peroxide (1.0 M and 0.6 M respectively, 65 oC) were used for leaching, while Fe, Cu and Co dissolutions were each about 80%. Therefore, using high pressure oxidative leaching provides a possibility to effectively extract Ni, Cu and Co while producing an environmentally benign residue, thus alleviating the current adverse environmental issues associated with the abandoned smelter slag. Keywords: Slag, amorphous, fayalite, atmospheric beaker leaching, high-pressure oxidative leaching, extraction

Jan 1, 2020

By Bolger Witthaus

"High performance production under challenging geological conditions is a product of several parameters. Main factors are the technical equipment and the knowledge in processing. The design and the support system of maingates must also be taken into consideration. The extraction of seams in German underground hard coal mines of RAG in a range of heights between approximately 1.1 and 4.0 m ( 4 and 13 ft) is done by plow and shearer technology. A complete system for quality management of production is required. The process examination of processes begins with procurement of the equipment. Education and training of the engineers and specialists, as well as for the miners are requirements for success as well.This report gives an overview of RAG measures for achieving high performance. Starting with examination of the processes accompanying procurement of equipment, the following important elements are described. Standards in education and training, technical design and elements of automated processing using stateof- the-art in control systems are critical to this system.The application of automation plays a decisive role in modem coal mines. The latest development in German coal mines is the fully-automated shearer system for longwalls. This helps to enhance safety, particularly in difficult ground conditions, by removing the shearer and shield operators from the immediate mining activity.INTRODUCTIONLongwall mining in carboniferous strata in Germany faces various challenges. Different longwall systems are used to mine up to 24 seams, each with a thickness between 1.1 m (3.6 ft) and 4.0 m (13 ft). High stresses due to a depth of up to 1,400 m (4,593 ft) requiring pillars between the panels, require special systems for roadway development, roadway support and reinforcemen.t as well as for longwall advance operations. Two main types of equipment for extraction are shearer and plow systems. While shearers are utilized for seam thicknesses above approximately 1.8 m (6 ft), plow systems can be used for smaller seam thicknesses between 1.8 m (6 ft) and approximately 1.0 m (3 ft)."

Jan 1, 2010

By F. N. Rhines, A. S. Nemy

The mode of high-temperature tertiary creep of 523-0 aluminum alloy was found to be strongly stress dependent. The occurrence of necking and/or fissures during tertiary creep exhibited a sequence with varying stress, wherein fissures with no necking occur at a minimum stress and necking with no fissures occur at a maximum stress. At an intermediate stress, tertiary creep begins without necking but with fissures in a region just beneath the external surface, followed by necking and the development of fissures along the axis of the specimen. The results are interpreted in terms of grain boundary gliding and the hydrostatic stresses produced by restraints to grain boundary gliding. THERE appear to be two possible reasons for the existence of a period of accelerating elongation prior to rupture during high-temperature creep in metals; namely, 1) a change in the structure of the metal itself, leading to a change in its response to loading, and 2) a reduction in the cross section of the metal resulting in a higher unit loading. Howe,' by annealing and retesting broken low-temperature creep specimens, found that irreparable damage is done once a metal is subjected to creep. Andrade2 first pointed out the association between the reduction in cross section and the increase in creep rate. The present research was designed to investigate both of these factors by retesting specimens machined from material which had been subjected to high-temperature creep testing short of rupture. EXPERIMENTAL METHOD An aluminum alloy, 52s-0, was selected for these studies because it is constitutionally simple, is strong enough to be relatively insensitive to mechanical damage during machining,3 and undergoes accelerating creep in a convenient temperature range. This alloy is hardened by 2.6 wt pct Mg in solid solution and is not subject to overaging effects; it has a very small quantity of an insoluble impurity phase, Mg2Si, finely dispersed throughout its micro-structure. Creep specimens, similar in design to ASTM 0.252-in. tensile specimens, were machined from 3/4-in. round stock and the surfaces were electro-polished. A 24-hr anneal at 500°C was then applied to stabilize the grain size to an average diameier of 0.27 mm. Subsequent heating for as long as 700 hr at the intended test temperatures produced no change in the tensile properties, indicating a well-stabilized state of the material. Corresponding to each of the typical testing conditions listed in Table I, one creep specimen was tested to destruction and this test was employed as a guide in the selection of times for subsequent tests. Duplicate creep tests were then run to various points along the creep curve to produce specimens which were used to determine changes in mechanical properties and microstructures. The latter were examined at the midsections of the specimens. Other specimens were tested to various stages of tertiary creep, after which they were remachined to new cylindrical test specimens, electropolished and re-tested in creep. RESULTS The major findings of this investigation may be illustrated by a comparison of the results of three sets of creep tests. These were run at 400°C at three stress levels, namely 750, 1000, and 1500 psi. In presenting these results in Figs. 1, 5, and 8, the creep curves are given in pairs: That curve of each pair which is drawn through filled circles corresponds to the initial test, and the curve drawn through open circles (and designated by - R) represents the result of retesting the same specimen after machining to a new cylindrical surface. The load was readjusted to the original unit stress at the beginning of each retest.

Jan 1, 1960

By K. K. Kelley, W. W. Weller

Heat capacity measurements of akermanite ( Ca,MgSiO ) , cordierite (Mg2A14 Sig018 ) , gehlenite ( Ca₂Al₂ SiO ) , and merwinite ( Ca ,MgSiO ) were conducted over the temperature range from 50 ° to 298.15 ° K. The entropies at 298.15 K ( expressed in cal / deg mole ) were evaluated as follows : Akermanite , 50.0 ± 0.5 ; cordierite , 97.3 ± 0.9 ; gehlenite , 47.4 ± 0.4 ; and merwinite , 60.5 ± 0.5 . All four compounds have positive entropies of formation from their constituent oxides at 298.15 ° K ; the values range from 4.6 cal /deg mole for akermanite to 10.1 cal / deg mole for cordierite .

Jan 1, 1963

By B. J. Moore

This Bureau of Mines publication reviews U.S. helium resources as of January 1, 1973. These resources, estimated to be 693.7 billion cubic feet, are broken down into four classifications, as follows: helium in storage, 34.9 billion cubic feet; helium in measured helium-rich natural gas reserves, 119.5 billion cubic feet; helium in measured helium-lean natural gas reserves, 62.8 billion cubic feet; and helium in indicated or undiscovered natural gas resources, 476.5 billion cubic feet. The helium in undiscovered natural gas is considered a national resource; however, this gas may not be discovered depending on many factors beyond the scope of this paper, and most of the helium in natural gas will be dissipated as the gas is consumed for fuel and other purposes.

Jan 1, 1976

By B. P. Sullivan

This paper describes how the author projected the economic benefits of a proposed coal liquefaction project based in Pennsylvania. These benefits were assessed in a successful effort to garner government support for the project. The projections considered such issues as increases in employment, wages, and tax receipts to state and local government, plus other less-obvious benefits, such as site remediation. The paper explains how sponsors of similar projects can use economic projections in making meaningful and compelling presentations to federal, state and local authorities.

Jan 1, 2000

The Chamber of Minerals and Energy of Western Australia Inc (CME) is the peak resources sector representative body in Western Australia. The paper gives a summary of the role and objectives of the CME, including its history, structure and key program areas. Particular attention is given to the role of the CME in the Eastern Goldfields of Western Australia. The paper details the types of CME membership that are currently in existence. The paper argues that a strong and vibrant CME is vital to secure the resources sectorÆs growth and development in future years.

Jan 1, 2006

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

By C. Cunningham

The process of initiating opencast blasts through long cables is onerous. An obvious alternative is to replace these with radio controlled firing apparatus. Such devices appear from time to time and with the advance of telecommunications, more are likely to appear. However, there are two crucial and seemingly intractable obstacles to overcome: firstly, the problem of malfunction of the system, which can either fire prematurely or go into a state of suspense in which it is unknown whether firing might unexpectedly occur, and secondly, the problem of terrorism, as such a system could provide the capability for an off the shelf remote bomb. The issues of accessibility and electronic reliability when linked to explosives in a mining environment have to be demonstrated to be adequately covered before serious consideration should be given to these systems, up to now largely confined to military applications.

Jan 1, 2003

By P Klaric, N Swart, S Barnes

The recent advances in digital imaging technology, specifically around photogrammetry, have facilitated precision measurement in the difficult conditions encountered in an underground development mining environment. With the recent downturn in the resources industry, many mining houses have begun to focus on cost reduction projects and driving efficiencies. The application of digital photogrammetry has allowed greater insight into the development mining cycle and supported a focus on areas where efficiencies and cost savings can be achieved. Data collation, via digital image capture, can be completed with minimal disruption to the development mining cycle with analyses taking a nominal time to process and interpret. The result can be a stark visual representation of the result of blasting and associated activities of the development mining cycle. Many millions of dollars of benefit can be derived from understanding the impact of each component of the development mining process, with some of the biggest savings associated with conformance to drill design and the minimisation of overbreak during blasting. This paper will explain the image capture process, analyses and instigated improvement opportunities that were undertaken at a number of mine sites to improve efficiencies and drive savings in their development mining processes.CITATION:Klaric, P, Swart, N and Barnes, S, 2017. Digital imaging provides valuable insights into underground development mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 129–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By A Kamaraj, M Mohanasundaram, R Kumar, P Tikare

This study presents a comprehensive thermodynamic optimisation and sustainability analysis of the secondary copper smelting process for Waste Printed Circuit Board (WPCB) recycling. The study investigates various scenarios with different proportions of WPCB in the input stream, ranging from 0 per cent to 100 per cent. Through thermodynamic modelling using FactSage™ version 8.1, the optimisation process is conducted in three stages. The results of the thermodynamic modelling indicate that the best-case scenario for WPCB recycling is achieved with a 40 per cent proportion of WPCB in the input stream. This case exhibits a maximum copper recovery of 99.93 per cent while minimising the formation of other waste. In addition to the thermodynamic analyses, environmental factors such as the carbon emission index and resource utilisation efficiency are studied. The 40 per cent WPCB recycling case exhibits a resource utilisation efficiency of 93.055 per cent and a carbon emission rate of 0.133. The present investigation highlights the significant benefits of a 40 per cent WPCB recycling scenario through a secondary copper smelting process in terms of base metal recovery and energy efficiency, thus emphasising its potential for sustainable PCB waste management and resource utilisation.

Aug 21, 2024

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached to remove base metals from a concentrate containing platinum group metals (PGMs). We investigated the atmospheric leaching process to develop a better understanding of the leaching behaviour of the base metals (Cu, Fe, and Ni) and the PGMs, in particular Ru, Ir, and Rh with respect to key process variables, acid concentration, and Cu concentration under oxidative and non-oxidative conditions. With oxidative leaching, a higher initial acid concentration resulted in higher Cu, Ni, and Fe extractions, as well as faster leaching reaction rates. A higher initial acid concentration also resulted in faster precipitation of Cu, Ru, and Ir under oxidizing conditions. Under non-oxidative conditions, Ni and Fe extraction was much slower, and the effect of initial acid concentration on Cu precipitation was less pronounced. The initial Cu concentration had a slightly smaller effect on the leaching behaviour of Fe and Ni, as well as precipitation of Ru, Ir and Rh. Moreover, a higher initial Cu concentration suppressed both Ni and Fe leaching and had a slight inhibiting effect on the precipitation behaviour of Cu, Ru, and Ir.

Nov 1, 2021

By G. H. Bennett

A field experiment was performed in a production unit of an operating copper room and pillar mine to compare the support capabilities provided by resin and mechanical roof bolts. Resin and mechanical roof bolts were alternately installed in eight intersections in a single entry. Rock mechanics instrumentation was installed to measure roof sag, bed separation, convergence, bolt pullout, torque, and strain. Bolt cost and installation time are included. Two analyses of the test were made. The analysis of the rock mechanics data showed there was no definite difference between the two bolting systems. From a broader analysis on a mine-wide basis it was concluded that resin bolts gave better support. A critical view of the experiment is given in the appendix.

Jan 1, 1974

By Vernon O. Markworth

This report contains the results of tests performed on three large diesel engines to determine their ability to meet selected criteria of the Mining Enforcement and Safety Administration Regulations for equipment used in gassy, non-coal mines. Study efforts were first directed toward determining the types of equipment expected to be used in underground oil shale mines. Three typical engines in the 800-1200 horsepower range were then selected for testing. Intake flame arresters, exhaust scrubbers, and water jacketed exhaust system were designed and built for each engine. During testing, each engine was evaluated for its gaseous emissions output, adequacy of the exhaust gas cooling system, ability to withstand internal explosions, and adequacy of the flame arresters. Surface temperatures of the engine and exhaust cooling system were determined under full load operation.

Jan 1, 1978

By P. G. Lazenby

This paper describes the latest instrumentation improvements in the INPUT Airborne E.M. System, particularly the new electronic signal-processing techniques. Several anomaly examples illustrating these techniques are shown.

Jan 1, 1973