Search Documents

By Mikula PA

This paper presents the results of in-situ and laboratory investigations into a mining method which utilises conventional continuous mining techniques to carry out two passes in thick coal seams, resulting in the development of stable pillars with relatively small width dimensions and heights up to 6 m. Geotechnical investigations included structural mapping, brightness logging and standard laboratory testing. Virgin stress was measured using overcoring techniques. Two approaches to pillar design were used in the study. These were; pillar design based on empirical formulae and laboratory testing, and pillar disign using calibrated mathematical models. A trial panel was developed at 300 m depth to study pillar deformation and stress changes due to mining. The extent of rib deformation was studied using borescopes and extensometers. In-situ geotechnical measurements were used to calibrate displacement discontinuity and finite element mathematical models of the coal seam. These models were then used to predict the behaviour of a small panel of pillars which were to be developed to 6 m height. The mining method was shown to be feasible provided adequate rib support was installed. The benefit of rib support was found to be two-fold, in that it increased confinement of the pillar in zones of low horizontal stress, while reducing horizontal stress relaxation in zones of high horizontal virgin stress. The possiblity of roof control by designing the small pillars to yield on retreat is discussed.

Jan 1, 1986

By M. J. Pool, P. J. Spencer

Using liquid tin as the solvent metal, the heats of solution of silver and gold in dilute Ag-Au-Sn alloys have been determined at 723°K by solution calorimetry. From the values obtained, the various enthalpy interaction coefficients in the liquid solutions have been calculated. The self-interaction coefficients Au and Ag values of 2413 and -6322 cal per g-atom in binary Au-Sn and Ag-Sn alloys, respectively. For an alloy containing 0.04 mole fraction Ag, Au is equal to 2443 cal per g-atom, and in an alloy containing 0.04 mole fraction Au, Ag has a value of —8883 cal per g-atom. Ag Au has been determined as —2650 cal per g-atom. ADDITION of a second solute to a dilute binary alloy may cause striking changes in the thermodynamic characteristics of the alloy. As yet, such influences cannot be reliably predicted and it is only by accumulation and critical assessment of data that definite patterns can be established. Solute interactions in dilute solutions were first treated mathematically by Wagner,1 who derived expressions for the Gibbs energy interaction coefficients. For an alloy consisting of. two dilute solutes, i and j, in a solvent s, these coefficients are given by: where yi is the activity coefficient of component i and x represents the mole fraction of solute or solvent. Other interaction coefficients have since been established in terms of the various partial molar thermodynamic properties of an alloy; the definitions of these are summarized in a recent paper by Lupis and Elliott.2 Mathematical and experimental studies of such coefficients have received much attention recently, providing a very useful theoretical background to an understanding of the nature of solute interactions taking place in dilute solutions. One of the definitions to arise from such work has been the extension of Wagner's treatment by Lupis and Elliott4 to include an enthalpy interaction coefficient, defined as. where ?Hi is the relative partial molar enthalpy of component i. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hio, and to the enthalpy interaction coefficients by the expression: Values of ?Hi can often be obtained with a high degree of accuracy by calorimetry, and, if the composition of the alloy is carefully controlled by making calculated solute additions throughout a series of measurements, application of Eq. [2] will enable reliable enthalpy interaction coefficients to be determined. Partial heats of solution must be investigated as a function of solute concentrations down to xi = 0, and, since ? values are obtained from the slope of mi plotted against x, great care must be taken to obtain precise data. The data for binary systems which are presently available often require extrapolation of ?Hi values from compositions as great as xi = 0.05 or even 0.1 to obtain limiting heats of solution. Reliable enthalpy interaction coefficients are thus impossible to obtain from published data for most of the alloy systems already investigated. The aim of the present work was to determine values of Au, Ag, Ag, and Au in the limit xsn -1 for the relatively simple Ag-Au-Sn system and from these results to gain some insight into the possible influence

Jan 1, 1969

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface metal/nonmetal mines by state during 1990-2001. Table 19 also shows the injury risk rates, employees' working hours, and lost workdays. A total of 79 fires occurred in 16 states during 1990-2001 for these mines. Forty-five of the fires caused 44 injuries and 2 fatalities (including 9 fires and 7 injuries involving contractors). The yearly average was 6.6 fires and 3.7 injuries. Sixty-five fires with 31 injuries and 2 fatalities occurred at metal mines, and 14 fires with 13 injuries occurred at nonmetal mines. The Ewhr value was 546 x 106 hr (In = 0.016), and the LWD value was 13,134. Nevada and Arizona had the most fires (19 fires, 10 injuries, and 1 fatality; and 19 fires and 11 injuries, respectively). They were followed by Minnesota (11 fires, 4 injuries, and 1 fatality) and Alaska (6 fires and 4 injuries). Of these states, Alaska had the highest injury risk rate value (In = 0.079). Table 20, partly illustrated in figure 8, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased during the second period, then decreased during most of the remaining periods. The number of fire injuries decreased during most of the periods (a small increase is seen during the last period), accompanied by a decline in employees' working hours during most of the periods (a small increase is seen during the third and fourth periods). The In values follow patterns similar to those shown by the number of fire injuries. Tables 21-26 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 9 shows the major variables related to fires for 1990-2001. Table 27 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By F Shi, W Huang, D Seaman, K Runge

High Voltage Pulse (HVP) technology is a novel process that could potentially be the step-change needed in ore processability in the mining industry. The propensity of high voltage pulses towards mineral-enriched ore particles during treatment makes this technology selective and has the potential to enable ore pre-concentration by size separation. In this study, the potential for pre-concentration of a low grade copper-gold ore sample subjected to HVP pretreatment is investigated and compared to that achievable after mechanical breakage in JKMRC’s rotary breakage tester (JKRBT). The data show that a better pre-concentration result can be achieved after HVP processing than conventional breakage. The gold pre-concentration potential is much better than that observed for copper. 4D HVP pre-concentration characteristic curves were produced to assess the metallurgical performance possible as a function of energy input. The case study shows that when targeting a nominal metal recovery of 90 per cent for gold, the HVP pre-concentration technique can split the low grade ore (0.9 ppm gold and 0.28 per cent copper in the feed size 26.5-37.5 mm) into two components – a low grade oversize material (0.3 ppm gold and 0.15 per cent copper) and a high grade undersize material (1.0 ppm gold and 0.3 per cent copper). The mass split to the low grade is 23 per cent. Under this mass split scenario, gold recovery to screen undersize is 90 per cent and copper recovery is 85 per cent. The HVP treatment of this feed size requires a specific energy (spark) of 2.8 kWh/t.There is further research that would be required before industrial uptake of the HVP pre-concentration technology would be possible. This paper also outlines the research challenges that need to be overcome.CITATION:Huang, W, Shi, F, Antonio, C, Runge, K and Seaman, D, 2018. High-voltage pulse pre-concentration study using a low-grade copper-gold ore, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 327–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M. C. Holton

South Africa has the world?s largest in situ deposits of platinum group metals, but economically exploitable resources are shrinking due to escalating costs and technical challenges. The South African National Research and Development Strategy comments that an increase in the knowledge intensity of the resource-based sectors is required to turn these resources to account. Highly trained human resources, continuous improvement, technological innovation, and smart acquisition of know-how will become the major differentiators in the global mining market. Mechanization and, ultimately, automation in mining have the potential to reverse the negative mining trend and resolve safety and other challenges. However, the adoption rate of mechanized mining in platinum (and hard-rock gold) has been slow for various reasons. Changing systems from conventional drill?and-blast to continuous mechanized mining is a big step-change endeavour. The problem of transformation is discussed, and the discipline of systems engineering is examined because of its successful application in aerospace and defence.

Jan 1, 2012

By A. T. Iannacchione

Roof-rock instability in advancing sections of underground coal mines is a major contributing factor to accidents resulting in fatalities and injuries. Such roof-rock conditions can also result in loss of production due to additional cleanup time and increased amounts of reject material. The Bureau of Mines is investigating fundamental geologic factors affecting coal mine roof-rock instability in order to develop techniques to predict zones of potential unstable roof-rock. Two distinct directional trends of unstable shale roof-rock in a mine working the Upper Kittanning Coalbed are delineated: one trend is associated with the sandstone-shale transition zone, the other with a fault system. The unstable shale roof-rock associated with the transition zone, a consequence of differential compaction, is comprised of slickensided roof-rock. Whereas, the unstable shale roof-rock associated with the fault system, a consequence of structural deformation of the strata, is comprised of fault planes. These faults, small in comparison to the sandstone-shale transition zone, are difficult to delineate with a standard drilling program. Trends of the transition zone associated with the sedimentary facies change are projected into unmined portions of the coalbed with the aid of exploration core data.

Jan 1, 1981

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

This report describes serious injuries occurring to bulldozer operators working at U.S. coal, metal, and nonmetal mines. The period covered is 1988-97. The data were collected by the Mine Safety and Health Administration (MSHA). A total of 873 injury records are examined. These injuries resulted in 18 fatalities and 31,866 lost workdays. All of these injuries occurred to dozer operators while they were doing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Injury records are categorized by activity (task being done), incident result (what apparently happened to the dozer), and operator impact (how the operator was injured). Where information is available, contributing factors are identified. This classification system supplemented the standard injury/illness data classification system compiled by MSHA. The results of the study indicate that, from 1993 to 1997, the number of serious injuries to dozer operators declined by 30%. The reduction in serious injuries was accompanied by a decrease in days lost due to injury. Although the number of reported injuries has decreased, dozer operators being jolted and jarred accounts for the largest percentage (70% of the incidents) and severity (75% of the workdays lost) of serious injuries while operating the equipment. Vertical jars (while backing up the dozer) resulting in injury to the operator accounted for a sizable percentage of jolting and jarring injuries. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over, or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fall over or rollover, 7 out of 26 were killed. Overall, 80% of the fatalities occurred while working near an edge or hidden void or on a steep slope. Further reductions in injury risk will require more widespread use of seatbelts, field and laboratory research interventions to better assess the effect of alternative engineering (e.g., seat and seat suspension) designs to dampen or isolate the effects of shock and vibration, and continued focus on hazard awareness, recognition, and response.

Jan 4, 2001

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Mining Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost-has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this exceedingly interesting subject. In the working up of the electrical arrangements touched on in this paper, the author has had the able assistance of hisfriend Mr. F. J. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer isbetter than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant.Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of regulating factors before it is possible to arrive at a proper decision.

Jan 1, 1911

By D. J. Barratt

The application of autogenous and semi-autogenous grinding circuits in recent years has contributed toward substantial savings in capital and operating costs compared to conventional circuits, particularly for large scale copper and molybdenum operations. Such savings have been realized from the deletion of operating, maintenance, equipment purchase and substantial civil/structural costs associated with secondary-/tertiary crushing and screening, fine ore storage and conveying. In spite of the downturn in the copper- moly industry in North America, there is still an interest in autogenous and semi-autogenous grincting for copper-zinc, gold and silver ores and in the overseas market. Both single-stage and two-stage circuits are in operation. Primary circuits operate autogenously or semi-autogenously in either open or closed-circuit. Critical sizes are extracted and crushed for recycle in some cases (e.g. ABC circuit). Secondary grinding is conducted using ball mills or pebble mills.

Jan 1, 1985

By J. Kalynchuk, R. Poulin, R. Pakalnis, D. Peterson

"A market survey of all underground mines in Canada (Fig. 1) was completed to determine the ex1ent to which cable bolts are being used as ground support. One hundred and nine questionnaires were distributed with 65% of them being returned completed. As a result, the quantity, types and locations of cable bolt installations have been determined. In addition, the grout pumps used, time required and cost of installations have been addressed. The popularity of other support types used in underground mines is summarized.IntroductionRock reinforcement consists of installing support within the rock mass (internal) or within the excavation (external). Within the past twenty-five years several new types of ground support have been introduced within the mining industry. Cable bolts were first introduced to the Canadian mining industry in the 19605 (Gramoli, 1975).Cable bolts have gained increased acceptance as a method of ground support during the past decade. The cable bolt is comprised of one central wire surrounded by six slightly smaller outside wires and typically having an over-all diameter of 15.2 nun to 15.9 nun (0.6 in. to 0.625 in.). The cable wires are made from high-strength steel with an ultimate strength of 26 tonnes (58 000 Ibs) (Goris, 1990). Current cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to reinforce the surrounding rock mass. Cable bolts are a form of internal support and are generally used in open stoping and cut-and-fill mining methods (Fig. 2).They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, they are generally less than 20 m (65.5 ft) and are untensioned. A major advantage compared to previously used ground support is that the cables are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils allowing relatively long support to be installed in areas with limited head room (1.8 m).With the advent of bulk mining methods which require comparatively large stopes, it has necessitated the use of relatively long support tendons to stabilize the large spans being created. As a result, the use of cable bolts for ground support in mines has increased significantly within the past decade."

Jan 1, 1995

By E. J. Gleim

[of- ac tore affecting the e -success of recent conveyor miningsystems forLt. extraction. 1 GL C ,_tfreedom shoot &apos;_)`u 2--ethe.1 is coal while e en othershot firers re:7 t _e&apos; _U-tin , w J, e coal .Z- 311.ing States conveyors because ;-.;lax .ca requires thatblasting be limited to when c .. men os. _o tend neces¬sary officials 1 s . re out c-z ,r 7t ...y e:e l z<: woes no t a -¬#to 1 C" such restriction on blasting conveyor miningbeen extendedWhere ere t ere. re no _ c: t&apos;_ _c tit-----! . kind cutlasting;,1CL?; C&apos;. _ z)carried anI-7LC. AT continuouslyHowever, unless et._&apos;0:, precations are taken under r&apos;t e , accidents, n is or such, as111 electricity r 1C- from.J--_,._.1t ,° =&apos;1?without usingholes, as well as numerous-o _&apos;1&apos;-1 -= e troublehe record of mineexplosions (some of themSo so _C&apos;_ °:&apos;,v 0f rock- dusting]

Jan 1, 1941

By Larry A. Enloe

The 16-to-1 milling operation is Sunshine Mining Company&apos;s first new silver and gold producing facility. The 16-to-1 underground mine and mill are located approximately 64 km (40 miles) southwest of Tonopah, Nevada. Ore re- serves in the epithermal vein deposit are estimated at 0.91 Mt (one million st) of ore, at an average silver grade of 206 to 240 g/t (6 to 7 oz/st) and an average gold grade of 1.2 g/t (0.035 oz/st). The underground mine uses a large diameter blasthole stoping system of mining using highly mechanized rubber-tired equipment. The mill uses conventional cyanide leaching with countercurrent decantation and Merrill-Crowe precipitation. The mill start-up was in February 1982 resulting in the first pour of dore&apos; in March 1982. The mill&apos;s present annual production is approximately 31.1 t (1.0 million oz) of silver and 264 kg (8500 oz) of gold.

Jan 1, 1984

By Roberto de Moraes

Lunar construction faces unique challenges arising from the nature of regolith and megaregolith. Unlike terrestrial soils shaped by weathering, lunar regolith is composed of angular, poorly sorted particles produced by impacts, with bulk Density, strength, and trafficability varying sharply with depth and terrain. Boulder fields, floaters, and talus aprons add further complexity, disrupting excavation and mobility. Apollo missions documented these conditions through drive-tube samples, trenching, penetrometer data, trafficability tests, and seismic profiling, but the results remained as datasets rather than a unifying classification. This paper introduces the LRC (Lunar Regolith Classification) Framework and the Overconsolidation Ratio applied for the Moon (OCR*), the first contractor-ready system to organize Apollo-derived trends into excavation demand zones (L1–L5). LRC is explicitly a classification, not a stratigraphy: depth ranges are indicative and require in-situ verification before use. Each zone is defined by bulk density and strength ranges, field proxies (bootprints, trench stability, auger torque, seismic contrasts), and corresponding excavation implications. Worked examples from Apollo 15 (mare), Apollo 16 (highlands), and Apollo 17 (pyroclastics and talus) demonstrate how observed data translate into LRC zones. These cases show that LRC captures both systematic depth trends and sharp local heterogeneity. The framework standardizes excavation planning for landing pads, haul roads, berms, foundations, and tunneling trials, while converting floaters from hazards into resources. LRC thus provides a common language for lunar construction. Rooted in Apollo evidence but designed for Artemis verification, it is proposed as a living standard; a reference framework to guide site preparation, excavation, and risk management in the next phase of lunar development.

Feb 22, 2026

By Paul Wellman

The energy problem of the U. S; was emphasized by the oil embargo of late 1973 and early 1974 and it seemed for a time that the Federal Government, under pressure from the general public, might take some corrective action. However, this was not the case. With the gasoline lines gone and an apparent plentiful supply of petroleum products, public concern quickly dissipated., This country is more vulnerable to an oil embargo today than we were in 1973-1974 and this fact should be of concern to all our people. Since 1968, we have used oil and natural gas at a much more rapid rate than we have been able to find new domestic sources; thus, there is an increasing gap between domestic production and consumption and we have filled the gap with ever increasing oil&apos; imports. These imports have increased at an alarming rate in the recent past, some 58 percent in 1976 compared with 1975. Imports are nearing 8 million barrels per day. Then, by applying some simple arithmetic, at $12 per barrel, the resulting trade deficit is $96 million per day or $35 billion per year. Obviously, this cannot be tolerated by our economy over a long period of time. Historically, we have shifted from one fuel to another as is shown in this slide. In 1850 about 90 percent of our fuel requirements came from direct combustion of wood, by 1900 we shifted to coal for 70 percent of our fuel, and now about 78 percent of fuel requirements comes from oil and natural gas. The difference is that the previous shifts were voluntary and the one facing us now is of necessity.

Jan 1, 1977

By Andreas Nolte

This paper includes a comprehensive report about the metallurgical utilisation of reusable products from electronic scrap recycling, car shredding industry, used glasses an various waste products, such as slimes and flue dusts, generated in a secondary copper smelter. Depending on the copper content, the type of copper compounds and the characteristics of accompanying substances, the materials are treated by smelting in furnaces, operating under reducing or oxidizing conditions. HKs pyro- and hydrometallurgical processes, blast furnaces, converters anode furnaces, tin lead alloy plant and tankhouse will be outlined. The reusable products are categorized according to the origin of the materials and then presented in the form of quantity and quality balances. Processing methods, process able quantities and quality requirements of inputs are described. The utilization degree of the most important metals (copper, tin, lead and zinc) is described with graphics. The report is rounded by information on operating licence according to the environmental regulations of the Federal Republic of Germany and data concerning supply and contracts

Jan 1, 1997

By Earl T. Hayes

For several years the Northwest Electrodevelopment Laboratory of the Bureau of Mines, in cooperation with the Air Materiel Command, U. S. Air Force, has been studying zirconium alloys. A preliminary survey of these alloys has been completed and reported as a Bureau of Mines Report of Investigations. 4/ Originally the purpose was to determine the suitability of zirconium alloys in medium-temperature applications. However, data also were obtained on other properties of these alloys, and later the scope was broadened to include amore detailed investigation of a selected group. The zirconium-titanium system was one of those chosen. The Bureau of Mines has been instrumental in the commercial development of both of these metals and has constructed pilot plants for the production of titanium at Boulder City, Nev., and for zirconium at Albany, Oreg. Both elements are in subgroup A, fourth series of the periodic table, and therefore have many properties in common. Since both have similar atomic structures and lattice dimensions the possibility of extended mutual solubility seemed likely. Inc transition-point diagram of Fast indicated that the two metals are completely miscible in all proportions in both the alpha and beta forms.

Jan 1, 1951

By H. Lyn Bourne

This marks the 15th consecutive year for this column. During 1995, readers were asked to supply royalty data for construction raw materials especially for states where none is available. The response was discouraging and royalty data are still missing for several states for either sand and gravel or crushed stone. Several readers have said that this article has merit but more new information is needed to justify its continuation. Several articles and pieces of news relative to mineral royalties appeared in the trade journals. R. Lee Aston (E&MJ, November, 1995, p. 16N) described South Australian royalties as amended by the government in1994. The royalty rate (a percentage) was lowered but the assessed value for minerals was raised and the current rate amounts to 20 cents//t (18 cents/st).

Jan 1, 1996

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

By K. Ramji

"The development curve in the extractive sector has become longer, steeper, and riskier due to increased social, legal, and political risks from various stakeholders. Indigenous peoples are a unique stakeholder because their growing legal rights to lands and resources can often determine a project’s outcome. A project will only be successful if it is able to obtain the legal permits, withstand any judicial reviews, and gain and maintain the social license to operate. Stakeholder identification, management, and engagement are key risk-mitigation tools required to successfully convert risks into opportunities.RÉSUMÉ La courbe de développement du secteur de l’extraction s’est allongée, elle est devenue plus abrupte et plus hasardeuse en raison de l’accroissement des risques sociaux, légaux et politiques venant des divers intervenants. Les peuples autochtones sont des intervenants uniques puisque leurs droits légaux croissants sur les terres et les ressources déterminent souvent ce qu’il adviendra d’un projet. Un projet ne pourra réussir que s’il est capable d’obtenir les permis légaux, passer à travers les analyses judiciaires, puis obtenir et maintenir le permis social d’exploitation. L’identification des intervenants, la direction et l’engagement constituent les outils clés de l’atténuation des risques nécessaires pour bien convertir les risques en possibilités."

Jan 1, 2016