Search Documents

By Yotamu Stephen Rainford Hara

"The aim of our work is to investigate a low energy and clean route for the recovery of copper and cobalt from complex sulphide mineral concentrates. The mineral concentrates were roasted in air, in the presence of CaO (MS + CaO + 202 =MO+ CaS04) at temperatures below 973K. The roasted products containing CuO, CoO and Fe203 were carbothermically reduced at 1073K within an hour to preferentially reduce copper and cobalt. The kinetics of reactions were studied using the thermogravimetric technique and by characterisation ofreaction products using the XRDSEM-EDX techniques. The effects of MS:CaO ratio, roasting temperatures and physical nature of the mineral concentrates were analysed. The method for capturing S02 by forming CaS04 was analysed for reuse in the process. The energy balance for the above process is compared with that of conventional continuous smelting/converting process.1.0 IntroductionCopper sulphide mineral concentrates from Zambia contains substantial amouot of cobalt. The cobalt metal content in the concentrates ranges between 0.7 and 2 % weight, which corresponds to 3 and 9 % weight copper, based on the spot price of copper ($7 386/tone) and cobalt ($31 000/tone). Although the traditional approach using a combination of roasting-leaching-electrowining steps can be applied to recover copper and cobalt from sulphide mineral concentrates [1-4], there are two major draw backs of the traditional process: (i) the S02 emitted during roasting is too lean for economical conversion for sulphuric acid manufacture, which causes serious environmental pollution. (ii) silver and gold which are normally present in the sulphide concentrates are lost out [5] because they are not leachable by H2S04 or HCl which are the common leachants. The above two problems have been overcome by adopting flash smelting in which a rich S02 gas above 20% is produced [1, 5] and successfully converted into sulphuric acid. The precious metals tend to partition to blister copper and recovered during refming. However, nearly all cobalt is lost into the slag phase uoder oxidising condition which prevails during flash smelting. It is important to note that the cobalt content in the slag can be up to 2.6 % weight [6]. The recovery of cobalt from the slag is a process which requires huge amouot of energy since the slag is smelted above 1873K [6]. With a view of minimising the amouot of energy and S02 emission during metal recovery, our investigation involves roasting the sulphide concentrates in the presence of lime and reducing the roasted samples with carbon."

Jan 1, 2013

By W. L. Dare

This publication is one of a series by the Federal Bureau of Minus describing methods and costs of minim, uranium on the Colorado Plateau. The La Sal mine is in the Big Indian mining district, about 29 miles southeast of Moab, San Juan County, Utah. The claims that encompass the mine were located in March 1953, and the La Sal ore body was discovered as a result of a drilling program begun in August 1953. The mine is owned by the La Sal Mining & Development Co., a subsidiary of the Homestake Mining Co. Homestake continued the drilling program and in May 1954 began sinking a 572-foot shaft and constructing a surface plant. The plant and shaft were completed in October 1954. The La Sal ore body is in the Chinle (Triassic) formation. it is tabular and dips with the enclosing beds about 8° southwest. The ore body is generally 4 to 8 feet thick but in a few places is as much as 20 feet thick it is being developed by a series of strike drifts and dip inclines, driven within the ore stratum on about 100-foot centers. A haulage level driven beneath the ore body is connected by raises to the upper workings.

Jan 1, 1957

By G. F. Revey

All underground operations have limiting factors that influence overall profitability. Hoisting, hauling, available headings, labor, milling capacity and other factors limit how much material can be removed from an underground mine. Consequently, when mines use limited labor to handle the additional rock from overbreak and to perform extra ground support tasks, productive activity is replaced by non-productive work. Mining economics are further penalized when overbreak causes dilution of ore grades. This paper reviews organizational systems that mines have used to create environments which foster the creation of successful overbreak control programs. Actual case histories document the various quality improvement techniques, worker incentives, and practical project management systems used by these mines. A brief review of controlled blasting technology sources and overbreak measurement tools is also included.

Jan 1, 1997

By M. Imani, A. Fahimifar, A. H. Javid

"Current studies of bearing capacity for shallow foundations tend to rely on the hypothesis of an isolated footing. In practice a footing is never isolated; it is mostly in interaction with other footings. This paper focuses on a numerical study to evaluate the ultimate bearing capacity for two interfering strip footings resting on a rock mass in which the strength can be described by the generalised Hoek–Brown failure criterion. This criterion is applicable to intact rock or heavily jointed rock masses that can be considered homogeneous and isotropic.The material is assumed to exhibit perfect plasticity and obeys an associated flow rule. The effects of Hoek–Brown parameters including GSI, mi, and sci were studied and the corresponding results are presented. For different clear spacing (S) between the footings, values of the efficiency factor (?) were determined; where ? is defined as the ratio of the failure load for an interfering new footing of a given width (B) to that of a single isolated footing having the same width. The maximum value of (?) occurs at spaced between S/B = 0.5 to 1.0. The results have been compared with those available in the literature.INTRODUCTIONEvaluating the ultimate bearing capacity of rock masses is essential for important projects like dams and bridges. Closely spaced footings may occur on rock masses in the form of pier foundation and grillage footing. Close spacing lead to permit higher loads than can be bore by similar isolated footings. The ultimate bearing capacity of two interfering strip footings resting on cohesionless soil have been studied theoretically (Kumar, & Gosh, 2007; Kumar, & Kouzer, 2008; Stuart, 1962). Results revealed when two strip footings approached closely enough, failure zones affect each other and ultimate bearing capacity significantly increased."

Jan 1, 2015

By Oliver Bowles

"General.The term mica is probably derived from the Latin ""micare"", meaning to shine or glitter, for the brilliant reflection from mica flakes in rocks has directed more than ordinary attention to this group of minerals. Mica includes a group of several minerals all characterized by a perfect basal cleavage, by virtue of which they may be split into exceedingly thin plates. The minerals are of very common occurrence in all countries, constituting about 4 per cent of the igneous rocks of the world The term ""isinglass"" is sometimes applied to glazing mica, but this is incorrect, for true isinglass is a soluble combustible material made from the air bladders of certain fish. As a constituent of granites and schists, mica is present as flakes too small for commercial use. Mica occurs also as small scales in many sandstones. When granites decompose, the quartz and the white mica are the most resistant to weathering, and so remain when the other constituents have been decomposed and carried away. A secondary white mica known as sericite is formed by the metamorphosis of clay-bearing rocks, and thus, in extremely fine-grained form it constitutes an important constituent of slates and related rocks. Some schists contain a high percentage of mica, but the presence of large amounts of quartz and other minerals has up to the present time rendered them useless as commercial sources of mica for grinding. It is possible, however, that certain mica or seri-cite schists which are composed almost wholly of mica with very little quartz may be utilized for ground mica if found in large enough entity. Considerable micais sometimes found mixed with the residual kaolin that results from decomposition of pegmatites, and in one locality at least it has been recovered as a by-product in a clay purification plant."

May 1, 1922

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By Raja V. Ramani

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. An investigation was conducted of current mined-land planning practices to aid in the development of a procedure for evaluating postmining land use potentials. This investigation considered both the industry and public planning approach to mined-land planning. It included a detailed review of the impact of regulation, factors that determine land use, and current site planning methods employed by the mining industry. The methods of this investigation included three in-depth case studies of surface mines in the eastern, central, and western United States. A site planning pro-cess has been developed and applied to the surface mine case studies to evaluate the economic, environmental and social impacts of postmining land use alternatives. In add it ion, guidelines are proposed to enhance the cooperation between local land use planners and surface mine planners, as well as to improve comprehensive planning with regard to mineral resources at the local and regional level.

Jan 1, 1983

By B. J. Moore

This Bureau of Mines publication contains analyses and related source data for 276 natural gas samples from 23 States. All samples except four were collected during calendar year 1984. Those four samples were collected earlier, but releases granting permission to publish were not received until 1984. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of these investigations are published annually to make the information available to the petroleum industry and the general public. Twenty-eight publications have presented the results of 13,957 gas analyses made prior to 1984. The first three bulletins (1-3)2 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26-28) containing 8,453 analyses of samples collected since 1960.

Jan 1, 1985

By M. Peshko, J. C. Gingerich, L. W. Matthews

"Noranda has successfully developed and implemented two leading-edge mineral exploration technologies — hyperspectral remote sensing and 3-D seismic surveying. Airborne hyperspectral imaging provides detailed geological and mineralogical mapping capability at both a regional and project scale that facilitates improved selection of prospective terrain and an accelerated exploration cycle. Noranda, in partnership with Falconbridge, has licensed the exclusive use of the Earth Search Sciences Inc. (ESSI) Probe-1 hyperspectral scanners (128- channel, 0.43 µm to 2.5 µm spectral range) that are capable of mapping in excess of 3500 km2 per day at 10 m pixel resolution. The technology has been successfully deployed on four continents over a broad range of terrain from desert to boreal forest and the high Arctic.To augment the company’s deep search initiatives, Noranda has successfully modified and implemented existing 3-D seismic technology to help targeting massive sulphides located at depths ranging from 500 m to 2000 m. In the fall of 1998 and early 1999, Noranda completed an 18 km2, 3-D seismic program in eastern Canada by successfully drill testing acoustic impedance anomalies locating massive sulphides at depths in excess of 1100 m."

Jan 1, 2002

Jan 7, 1976

By Walter Steiner, Claus Becker

INTRODUCTION General Switzerland is a densely populated country in the heart of Europe. With its total surface of 41.300 km2 and a population of 6,8 million in 1986 the average population density is 163 capita / km2. The population density is lower than in Germany (245 capita/ km2) or the Netherlands (355 capita/km2). The USA have a population density of 26 capita/ km 2. However, sixty percent of the Swiss surface is covered by the Alps and another ten percent by the Jura mountains the remaining thirty percent of the surface is covered by the Swiss plateau where the majority of the population lives. The population in the inhabitated areas is thus substantially higher and may possibly reach those in major metropolitain areas. Due to the high population density in Europe in general and Switzerland in particular future traffic demands cannot be fulfilled sole by car or plane. Environmental and land-use constraints lead to the third option for growing transportation needs: High-speed rail (Bovy, 1990). Switzerland has developed its own approach to promote public transportation and in particular rail transportation: "Rail 2000" (Stalder, 1990). The system "Rail 2000" is based on a series of hubs distributed over Switzerland where easy connections can be made.

Jan 1, 1991

Visit to the Datsun Nissan Company's body pressing and assembly plant at Rosslyn, Pretoria, and the Claremont-Danville Tunnel on 27th February, 1970. The excursion arranged for the 27th February to the Datsun Nissan motor car assembly plant at Rosslyn, near Pretoria, in the morning and the Claremont-Danville tunnel in the afternoon was well supported by some 43 members. The visitors were met at the factory by Mr Rademeyer, the Industrial Relations Manager, and members of his staff and were taken to the artisan training centre for light refreshments. There is a well-equipped training section with an air-conditioned lecture hall; we were told that such training facilities were important because of the cosmopolitan nature of the artisan staff. The visitors were divided into small parties and taken to the tool die and jig-making section, which is perhaps the key department for a factory of this nature. There the many dies for the presses in the body pressing section, as well as the complicated jigs for body welding are made. The technique for making the castings for the dies is interesting. A polystyrene model of the casting is embedded in moulding sand. In a neighbouring foundry molten metal is pressed into the headers and burns away the polystyrene, which leaves no residue, and this exactly fills the space occupied by the model. This rough casting is then machined in large copying machines (costing as much as Rl80 000). An exact plastic model of the surface of the pressing required, set up in juxtaposition to this casting is traversed by a master stylus which operates the slave milling cutter, thereby machining the surface to close tolerances. The machined casting is cleaned up by hand and finally finished in large spotting machines, using a blue dye to show up high spots, to the fine degree of accuracy required. The body pressing section was next visited. There the large number of pressed parts which make up a vehicle body are pressed out of special deep drawing steel plate. Some of the largest presses were capable of applying a pressure of 1 200 tons and cost as much as Rl85 000 each. The visitors then followed through to the assembly section where jigs are used to hold together the many pressings, which are then spot welded into body frames. The frames go to an assembly line where they are finished to the stage for painting. The continuous crawl painting assembly line carries the frames through all the stages of prime coating with zinc phosphate sprayed on in a tunnel, followed by immersion of the lower parts in a priming bath, then drying and spray painting and baking in tunnels. The body frames, after painting, join another assembly line, where the doors, upholstery and many fittings are attached. After this stage the completed bodies are lowered onto and attached to the chassis units which are largely assembled from imported parts (engines, transmission units, etc.). From the end of the line the completed cars are driven off to the trial track and then pass through a tunnel with powerful water sprays to detect leaks in the body work. The proportion of locally made parts is just on 45 per cent. An interesting aspect of the assembly organization is that, of the 140 or 160 cars completed each day there may be included some of each of the Datsun model as well as some Renault and Alfa Romeo models models which are assembled by this company. The change from one model to another several times a day does not present any difficulty to the organization. Each section of the assembly plant 'buys' the units from the preceeding section and 'sells' to the succeeding section. This means that the responsibility of each section ends when the unit is sold to the next section. The cost of repairing any faults found subsequently is charged to the section where it is found, which puts a powerful emphasis on meticulous inspections between sections to safeguard their costs. After the tour the parties assembled at the lecture hall where a lavish cold buffet luncheon was provided by the company. After luncheon Mr A. R. C. Fowler, on behalf of the Institute, thanked the Managing Director, Mr W. J. Wilson and his staff for this most interesting and well organized visit. The party then left for the Claremont-Danville tunnel. The tunnel is being driven by General Mining Federale Kontrakteurs through the Daspoort Range, Pretoria, to link the suburbs of Danville, near Iscor, and Claremont, which at present can only be reached by a nine mile detour. It is estimated that some 6000 vehicles per day will use the tunnel. Before entering the tunnel a short talk was given by Mr Ross who is in charge of operations. He called on various officials and staff of the Consulting Engineering firm, Basil Read (Pty.) Ltd., to describe the tunnel and

By A A. Latscha, D O’Connor

Increasing orebody complexity, restrictions in ground access, and longer lead times for disturbance approvals, have generated the need for the Resource Development Team within Rio Tinto Iron Ore (RTIO), to explore optimised drill design techniques that deliver resource conversion value while maximising program outcomes. In response to this challenge, the Team initiated a case study to produce an AI assisted/designed drill program using a non-machine learning AI. The case study involved the assessment and implementation of an AI generated drill program at one of RTIO’s Pilbara iron ore deposits, located in the Hamersley Province of Western Australia. The Mineral Resource is currently classified as 100 per cent Inferred. Access constraints inherent to topography, and the presence of exclusions zones have prevented adequate drilling coverage, resulting in lower resource confidence and a poor definition of the orebody extents and geometry. The drill campaign, planned in Q1 2023, needs to consider access constraints, complex topology and the limitations related to additional ground clearance, while addressing the requirement of improving orebody knowledge. The drill plan had to address two objectives. The first and main aim of drilling was to upgrade the Resource Classification to allow for possible conversion to Ore Reserve. The input for this objective was a volumetric representation of the areas currently not meeting pre-defined quantitative Resource Classification upgrade criteria. The second objective was to better define the orebody extents and geometry. For the second objective, the input to the drilling optimiser was a volumetric representation (blocks) of the areas of high uncertainty in the mineralisation/waste boundary, which were defined using an indicator conditional simulation technique. The drilling optimiser output was a range of compliant drill plans. A set of KPIs based on economic and orebody knowledge criteria were used to assess the plans and to select the most optimal drill design to be drilled in 2023. The geology and management teams were able to make better informed, objective decisions using the trade-off between cost and orebody knowledge gained. As part of the assessment, the AI generated plans were compared to our current planning practises. The AI assisted plans, when gauged against the project KPIs, showed clear and measurable improvements in both meeting project objectives and in managing operational risk.

May 24, 2023

By John W. Cole

The Bureau of Mines conducted a trenching and sampling project during 1947 on the tungsten-rich granodiorite that outcrops in Henderson Gulch, Montana. During the course of this investigation, interest was attracted to the Sunrise copper-gold mine in metamorphosed limestone in the north slope of the gulch. The mine was examined by S. H. Lorain, Chief, Mining Division, Albany Branch, in May 1948. A trenching and drilling program was recommended to develop a parallel vein indicated by outcrops to lie below the principal productive Queen vein. In the meantime, the Queen Mining Syndicate initiated a trenching program that exposed high-grade lead-copper-silver-gold ore in a nearly vertical vein that strikes N. 600 E. to east. A core-drilling program to develop this vein was initiated in September 1948. This report presents the factual data obtained from the trenching and drilling operations. The Sunrise mine was discovered about 1890. Production has been estimated to be $120,000 in gold from 40,000 tons of ore mined during the period 1892-1903. The tailing from this operation was treated by cyanidation in 1912, with a reported recovery of $3.50 to $4.00 a ton from 15,000 tons of material. Subsequent production of sulfide ore was 7,396 tons treated by smelting, with recovery of 1,569.42 ounces of gold, 10,003 ounces of silver, 352,899 pounds of copper, and 354 pounds of lead.

Jan 1, 1950

By Luis Enrique Vargas

En las operaciones a tajo abierto, la generación y control de vibraciones juegan un papel importante en la estabilidad de taludes a lo largo del tiempo. Para mantener un diseño de minado óptimo y seguro en Toquepala, el autor ha contemplado 7 factores (caracterización geotécnica, diseño de malla, diseño de carga, análisis de secuencia de tiempos entre taladros y filas, análisis de vibración tanto en piso como en cara de banco, calidad del precorte y evaluación geotécnica de voladura mediante celdas) al desarrollar esta metodología denominada Evaluación geotécnica integral de voladura. El trabajo incluye conclusiones y recomendaciones precisas.

Sep 20, 2019

By M. P. Board

The U.S. Bureau of Mines, under a cooperative agreement with Hecla Mining Co., conducted a rock mechanics study at four widely spaced horizons in a deep mine shaft in northern Idaho. The objective of the project was to measure and analyze rock deformation and lining behavior during construction of a deep shaft in a high in situ stress field within an isotropic rock mass. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. This report discusses the general trends and magnitudes of data from the four test sites, and relates the data to a proposed anisotropic constitutive model for the rock mass. A design procedure is then outlined for specifications of liner thickness and support installation sequences for future shaft sinking.

Jan 1, 1989

By Ross. C. Barkley

A computer program has been written to simulate ground vibrations induced by multiple-hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosives charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g. velocity, attenuation, pulse), or by backcalculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties are backcalculating individual pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shown to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included and additional verifications with field results are required.

Jan 1, 1983

By Roy A. Anderson, Roger H. McConnel

The Metaline district from 1906 through 1965 has produced nearly 16 million tons of ore yielding 400,808 tons of zinc and 178,062 tons of lead. The sediments, ranging from Precambrian into the Devonian, are schist, phyllite, conglomerate, greenstone, quartzite, limestone, dolomite, and carbonaceous slates. Quartz monzonite and granodiorite of the Cretaceous(?) Kaniksu batholith are exposed over a large area beginning a few miles south of the district. There is minor Tertiary conglomerate and basalt. Abundant glacial deposits obscure much of the bedrock. Northeasterly trending folds, having steep to overturned northwesterly limbs, and thrust faults, striking northeasterly and dipping southeasterly, characterize the deformation of the Precambrian and Paleozoic rocks. Recent drilling indicates that the Slate Creek fault, too, is also a southeasterly dipping thrust fault. This new evidence suggests that the Valley Block, like the other major structural blocks, may in part be a thrust plate rather than a graben, and that thus the district may have greater structural unity with the surrounding region than has heretofore been apparent. The Cambrian Metaline Formation of limestone and dolomite contains essentially all the lead-zinc mineralization. Most of the ore mined to date has come from a carbonaceous and irregularly siliceous breccia of sedimentary and diagenetic origin, locally called the "Josephine Horizon," that makes up the top few to 200 feet of the formation. The Josephine Unit is a breccia of gray limestone, coarse light gray dolomite, very thin-bedded, dark gray siliceous dolomite, and "zebra rock" believed to be of algal origin, embedded in a matrix of black dolomite or black jasperoid or some mixture of these two. The jaspcroid fragments and irregular blobs embedded in the black dolomite matrix and the jasperoid laminae in the very thin-bedded dark gray dolomite suggest that jasperoid was formed at the same time as the breccia matrix and as the laminated dolomite. So too, the marked tendency of sphalerite and galena to be disseminated mainly in the dark breccia matrix and their tendency to be most abundant in the jasperoid laminae of the very thin-bedded dark gray dolomite, even where the mineralized and laminated dolomite is fragmented and engulfed in black dolomite breccia matrix, suggests that in these ha bits the sulfides also were deposited contemporaneously with the sediments. Yet very commonly, veins and vague veinlets and patches of white quartz, usually carrying rather coarse sphalerite and sometimes galena crosscut all rock types. These contradictory relationships throughout the Josephine Unit suggest that both the black jasperoid and the sulfides were original constituents of the Josephine Unit but that, locally, they later were remobilized and deposited as white quartz and coarser grained sulfides. Possibly, at least in part, this "metamorphism" is one of the effects produced during or shortly after the intrusion of the Kaniksu batholith.

Jan 1, 1968

By Jerry Wallace

Construction of a new grammar school required blasting within three meters of the existing school. Due to changes not anticipated at time of bid opening, blasting had to take place while approximately 200 children were in attendance inside the building. Blasting with children in such close proximity forced the blaster to review and revise a systematic approach to construction blasting and make changes to previous Rules of Thumb guidelines. The revised rules of thumb place Blaster-in-Charge at the top of the List. Other changes specific to the project included putting in place a blasting safety plan that included communicating the serious job hazards to teachers and students. The plan included stringent lockdown guidelines establishing school procedures for accounting for each student prior to the countdown-to-blast being implemented. Emergency communications channels were kept open so that any scheduled blast could be aborted at the last instance.

Jan 1, 2001

By J. L. Bray, S. T. Ross

The paper provides electrometallurgical data on the problem of germanium removal from zinc sulphate solutions. Germanium traces have caused much concern to the zinc refiner. Confirmatory evidence of interaction between germanium and cadmium is presented. Statistical analysis of data expands its significance and enhances its value. Further research is outlined. THE literature contains many references to the effects of trace amounts of germanium in the production of electrolytic zinc. One of the authors had experience with this troublesome element as early as 1917 at Trail, B. C. In 1929, Tainton and Clayton' reported that concentrations of as little as one part per million of germanium were sufficient to cause serious losses in current efficiency. Liddell2 reported that trace amounts of germanium cause marked lowering of the hydrogen overvoltage of electrolytic zinc cells, so that commercial production was impaired. Bray3 recorded the history of germanium in relation to electrolytic zinc production, noting that concentrations below 10 ppm have been found to yield low current efficiencies and copious hydrogen evolution. Koehler' stated that germanium "when present to the extent of a small fraction of one part per million per liter, causes serious evolution of hydrogen with a corresponding reduction in current efficiency." Recently, however, S. W. Ross" reported, from Risdon, Tasmania, that "in the course of leaching . .. dissolved traces of germanium... if not removed almost completely ... increase the reversion of cadmium during the filtration of the copper-cadmium precipitate and reduce the current efficiency during subsequent analysis." The copper-cadmium precipitate referred to is the residue from the zinc-dusting purification of zinc sulphate leach solutions. In the face of such conflicting testimony and with the increasing industrial importance of pure germanium and zinc it was decided to investigate the relationship between cadmium and germanium. Furthermore, other work by the authors showed certain discrepancies to exist in the theories of Tainton, et al. In the laboratory, without marked efficiency decreases, the authors have deposited zinc successfully from solutions containing as high as 1 g per liter of germanium. This could be done only when there was no cadmium present. Preliminary investigations of the suspected rela- tionships were carried out by means of emission spectrographic analysis using a beryllium internal standard. Several solutions containing 100 g per liter of zinc, as zinc sulphate, and 1 g per liter of cadmium, as cadmium chloride, were prepared. These concentrations were on the order of those obtained during a commercial low-acid leaching process. Varying concentrations of germanium were added to these solutions so that the range of 0.0000 to 0.5000 g per liter of germanium was covered. A 250 ml sample of each solution was agitated with 2.5 g of zinc dust for 30 min, filtered, and the filtrates were examined spectroscopically. Qualitative evidences of cadmium traces were found in those filtrates which originally contained above 10 ppm of germanium. Reliability of the analytical method did not permit quantitative investigations since cad-Table I. Current Efficiencies Obtained at 0.0000 and 1.5000 G per Liter Cadmium Concentrations Ge Concentrastion,* Cd Concentration,* EtBclenoy, G per Liter G per Llter Pot 0.0000 0.0000 84.270 0.0010 0.0000 94.849 0.0050 0.0000 92.649 0.0075 0.0000 94.039 0.0100 0.0000 96.084 0.0000 1.5000 93.460 0.0010 1.5000 95.158 0.0050 1.5000 92.148 0.0075 1.5000 91.260 0.0100 1.5000 84.546 • Cd and Ge concentrations shown are those existing before zinc-dust purification. mium determination in the concentrations present in zinc-dusted solutions lacks sufficient sensitivity for reproducible results. As a consequence of the inability of the investigators to obtain acceptable results through direct quantitative analysis, an indirect approach was devised. This indirect method involved a study of the current efficiency, in a model zinc cell, as a function of the concentrations of cadmium and germanium. Variables such as cell temperature, voltage, current density, anode spacing, relative electrode area, degree of agitation, cathode preparation technique, time, acid concentration, and solution volume were held constant. Fig. 1 shows the cell used. The current was fur-

Jan 1, 1952