Search Documents

By C Chen, T Kan

The distribution ratio of Pb (LPb s/m) between three types of slags (FeOx–SiO2, CaO–FeOx and FeOx– CaO–SiO2) and molten copper after equilibrium was measured at 1300°C and oxygen partial pressure (pO2) of 10-10–10-6 atm. Results showed that for FeOx–SiO2 slag, the LPb s/m increased from 0.024 to 2.57 with pO2 increased from 10-10 to 10-6 atm. The LPb s/m with CaO–FeOx slag was lower than the FeOx–SiO2 slag at the same pO2, ranging between 0.015 and 0.53. Using the FeOx–CaO– SiO2 slag generated LPb s/m values (0.02–1.6) in between. The oxygen partial pressure in the investigated range had no obvious effect on the activity coefficient of PbO (γPbO) which was averagely 0.44, 1.70 and 0.71 for FeOx–SiO2, CaO–FeOx and FeOx–CaO–SiO2 slags, respectively. The increases in the (CaO+MgO)/SiO2 mass ratio of the FeOx–CaO–SiO2 slag induced the decrease in the LPb s/m and the increase in the γPbO value. However, the variation in the Fe/SiO2 mass ratio didn’t exert obvious effects.

Jun 19, 2024

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By Wilton Johnson

Native asphalt was produced in 1981 by five companies in three States, Alabama, Texas, and Utah. Texas was the leading State in production of native asphalt. Total production increased in 1981 to 1.26 million tons, while value increased 10.5% to $27.7 million. Bituminous limestone, used primarily for street and road repair, was produced by Whites Uvalde Mines and Uvalde Rock Asphalt Co., both in Uvalde County, Tex., and Southern Stone Co., Colbert County, Ala. Gilsonite was produced by American Gilsonite Co., Uinta County, Utah, and Ziegler Chemical and Mineral Corp., Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1982

By FRANKM. SEIBERT, G. G. Oberfell, GEORGEA. BURRELL

The Bureau of Mines is conducting a series of investigations with the common aim of minimizing the losses that occur in the mining and treatment of mineral substances. The results of the investi- gations are being published in reports of the bureau. This report treats of a method of preventing some of the waste of the natural gas incidental to oil mining. This method, the condensation of gasoline from natural gas, offers to the oil operator and others a profitable means of utilizing some of the oil-well gas now being wasted. The most desired constituent of crude oil is obtained, the production of oil is not hindered, and the gas, after the extraction of gasoline, can be returned to the leased area to drive pumps or into pipe lines for uses to which natural gas is ordinarily put, usually with its fuel value lessened only in slight degree. Publications already issued briefly discuss the subject. In this report the work is treated in greater detail, and the results of many additional tests are shown.

Jan 1, 1915

By R. E. Vivas, J. A. Villa

"Located in the state of Colima, Peña Colorada is one of the largest iron ore operations in Mexico. The project is owned in equal parts by ArcelorMittal and Ternium. Though boasting a production capacity of 4.1 Mt/a (4.5 million stpy) of concentrate per year, Peña Colorada is faced with declining ore grades. In order to respond to this situation, Peña Colorada had to expand production even further. This expansion created various challenges that were overcome by the adoption and application of new technology. Examples of these technological innovations are discussed in detail in this article and include improvements in geo-modeling, mine planning, and mine operations. The successful implementation of these technologies paid for itself many times over, and has led to significant improvements in production and performance, while lowering the operating costs and reducing the variance between planning and execution.Project overviewPeña Colorada is a mining company that produces about 30 percent of the iron ore in Mexico. This project generates about 1,200 direct jobs and 3,000 indirect jobs, making a significant contribution to the local economy. Similarly, Peña Colorada invests in its local communities through numerous educational programs, scholarships, university agreements, social development, environmental agreements, etc. Peña Colorada’s operations consist of an open pit mine located in Minatitlán and a pellet plant located in the port city of Manzanillo, as shown in Fig. 1. Technological innovationsMost mining projects around the world typically follow the logic of “mining the next best ore.” Consequently, head grades tend to decline over the life of the mine. In the case of Peña Colorada, a decline in head grade combined with a decline in iron ore prices forced the operation to adapt to a new business environment and adopt new technologies to face these challenges. However, the first step along this process was to increase the confidence and reliability of the resource model. This task involved additional drillhole campaigns coupled with more detailed modeling techniques. Once the block model was completed, new optimization studies and production schedules were evaluated with new optimization tools that improved many aspects of the mine plan. The Peña Colorada block model has undergone 3 expansions to reflect additional information not available in the past. The model has expanded to the East and Southwest. The latest model expansion increased the total number of benches to 98 as a result of positive exploration results. Similarly, new geotechnical studies were prepared, which provided new guidelines for pit slope design, and new technology was implemented to monitor ground movement and slope stability. Two sectional block model views in Hexagon Mining’s MineSight 3D, along with the pit designs and geologic solids are shown in Fig. 2."

Feb 1, 2017

By J. C. Agarwal

Slags produced by modern smelting furnaces contain copper values which are unacceptably high for discard. The electric arc furnace is employed commercially to clean copper from flash furnace slags but the addition of highly oxidized converter slags to an electric furnace has created operational problems. Highly oxidized Noranda Reactor slags have not been processed successfully in a pyrometallurgical process. These slags, which contain large concentrations of copper (5 to 10 per cent), are treated in slag concentrators (controlled cooling, crushing and milling, and flotation) which produce a copper concentrate that must be resmelted. Though commercially operable, it will be shown that the slag concentrator has important process and cost disadvantages as compared to a pyrometallurgical process. In this paper an economic comparison is made between a pyrometallurgical process and the slag concentrator. For the analysis, five hypothetical smelting plants are considered. Each plant treats 1200 tons of copper concentrate per day and produces 109,000 tons of copper annually. The plant configurations used in this study are:

Jan 1, 1976

By D. O’Connor, A. Pytlik, D. J. Corbett

The resistance of yielding rockbolts to multiple impact loads was tested by means of a drop hammer. The methodology was based on the ASTM D7401-08 standard as well as the requirements specified for rockbolts by Luossavaara-Kiirunavaara Aktiebolag (LKAB – a Swedish mining company) and the Safety In Mines Research Advisory Committee of South Africa (project number GAP 423). During the tests, the loading force and bolt elongation were measured with a sampling frequency of fs = 19.2 kHz. In order to analyse the phenomena involved, the tests were recorded using two independent high-speed video cameras (600 and 1000 frames per second) and one thermal camera (128 frames per second). The tests demonstrated that all the samples transferred double the gravitational potential energy of Ep = 50.85 kJ from the impact load of mass m = 2825 kg and impact velocity of v = 6.0 m/s without failure. Damage to the bolt-resin contact in the upper anchoring zone of the bolt in the steel tube occurred after subsequent impacts. As a result, the macro-deformed bolt exhibits additional yield, and its operation following the shearing of the resin bond is similar to that of a ‘cone bolt’. Only one test resulted in damage to the threaded bolt rod-nut coupling, during the fourth impact; however, no damage to the bolt-resin contact zone was observed.

Nov 6, 2023

By F. Albayrak

This report is a study of the impact of Federal laws and regulations on the domestic supply of metallic and nonmetallic minerals. The study was confined to pertinent environmental legislation and the recently enacted Federal Mine Safety and Health Act of 1977. Emphasized were the legal requirements placed on individual selected mineral industries, and the economic impact of these requirements. A certain amount of attention was also directed to the particular environmental and health and safety problems generated by selected mineral industries. The study also pinpointed a list of major problem areas having significant impact on the domestic mineral supply.

Jan 1, 1978

By J. B. Zadra

Tungsten, a comparatively new metal, is one of the important strategic war materials. In peacetime, tungsten is widely used as a filament in elec¬tric lamps and electronic tubes and is a vital constituent of some of the most important industrial alloys. High-speed tool steel containing tungsten and stellite alloys containing cobalt, chromium, and tungsten are extremely hard and resistant to corrosion. These alloys and the tungsten carbides are unequaled as cutting tools and in other wear-resistant applications. They play a prominent role in the present era of mass production. Alloys containing tungsten resist oxidation at high temperatures and have been key alloys in the development of modern aircraft. The adaptability of tungsten to new uses is expanding, particularly in the high-temperature range. Domestic production of tungsten has come from a large number of deposits in 17 of the 49 States; but, of the total domestic output from 1900 to 1956, more than 80 percent was produced from mines in North Carolina, California, Colorado, and Nevada. The average tenor of the mined ore was less than 1 percent tungsten trioxide (W03).

Jan 1, 1959

By Joseph W. Horne

This report presents the results of an investigation by the U. S. Bureau of Mines in cooperation with the State of Colorado, on the yields and properties of oils produced from oil shale, lignite and subbituminous coal using the standard assay method developed by the Bureau for oil-shale testing,. The purpose of this work, which is part of the general study of oil shales being conducted by the Bureau of Mines and cooperating agencies, was to obtain information on the amount and character of the yield of crude oil or tar from different typical oil shales, the yield of light oil or naptha that might be suitable for use in motor fuels, and other products of shale oil. As the west has large resources both of oil shale and low-grade non-coking coals, it is of interest to know the relative yields of tars, light oils, and combustible gases that can be produced from these coals when retorted under conditions similar to those suited for oil-shale retorting. Source of Samples The coal samples were obtained from deposits on or adjacent to the public lands in the States of the Rocky Mountain region. Many of the mines sampled are operating under Government leases or permits. The number of coal samples secured from the various states are: Colorado, 6; Montana, 9; north Dakota, 6; New Mexico. 1; South Dakota, 1; Wyoming, 9. Of these samples, 14 were lignite coal, 16 subbituminous coal, and a bituminous coal. The standard channel method of the Bureau of Mines was used for sampling. Coal samples received at the Boulder Office weighed about twelve pounds each, and duplicate samples were sent to the Pittsburgh Station for proximate and ultimate analyses. The origin of the samples and description of the deposits are given in Table 1.

Jan 1, 1927

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"Abstract - The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973

By Andrew Abraham

Continual improvement is the key to success in today?s competitive global arena. You require tools that promote dynamic quality management, deliver cost savings to your bottom line and provide the foundation for process improvement. ISO 9000 and ISO 14001 management systems and OHSAS 18001 are those tools. Since their inception, the benefits of ISO management systems and registration have been touted as the way to achieve better bottom line results. This spurred many companies to embark upon the road to registration with high expectations. The potential benefits of ISO management system implementation and third party registration that are commonly provided by Registrars and consultants are compelling adverts for success. ISO 9001:2000 is promoted as an essential tool for systematic efficient and affective management controls that provide a framework for analyzing errors and improving a company?s internal operational processes. It also allows companies to comply with internal and external customer and regulatory requirements thus continually improving the quality of their products and services and thus enhancing customer satisfaction. This, in turn, leads to greater customer recognition and increased market share. ISO 14001 implementation and registration may assist your company in reducing its litigation risk, raw material and energy consumption, waste disposal costs and possibly non tariff trade barriers. It should also provide continuity of operations, enhanced operational efficiency and consequently a competitive advantage in the market place. Registration of your ISO 14001 management system should also improve your company?s profile and credibility leading to regulatory flexibility and improved community goodwill. All of this will be a catalyst for improved morale and pride by employees and management alike. Likewise, OHSAS 18001, the latest certification specification for Occupational Health and Safety Management Systems supports Occupational Health and Safety legal and regulatory obligations and compliance, manages & controls Occupational Health and Safety risks and improves performance, safety culture and efficiency. OHSAS 18001 is an audit certification, and not a legislative requirement. Suggested benefits of implementation include reduction in accidents, lost time and associated liability and insurance costs and improving reputation and credibility through demonstrated commitment to health and safety. The foregoing increases access to new customers, joint venture partners and financing The skeptics say these are motherhood statements and lack corroborative evidence, i.e., ?Show me the money!?

May 1, 2003

By C. Guria

A modeling, simulation and optimization study of a complex industrial fluorspar beneficiation plant (Kadipani, Gujarat, India) with fourteen/ten flotation banks is carried out to find an optimum/near-optimum circuit for the given quality of feed ore. The phenomenological flotation model developed by Mehrotra and Kapur (1974) is used for circuit optimization. Two different optimization problems are formulated and solved. The first optimization problem involves a single objective function, which uses available plant data to estimate the feed-characterizing parameters, i.e., the flotation rate constants, by minimizing the weighted sum-of-square errors between the computed and plant values. The second optimization problem involves two objective functions to obtain several simplified circuits. The number of non-linking streams and the overall recovery of the concentrate, i.e., the acid-grade product, are maximized simultaneously in this problem. The single-objective variant (SGA-II-mJG) of the binary-coded elitist non-dominated sorting genetic algorithm with the jumping gene adaptation, NSGA-II-mJG, is used for the first problem, while NAGA-II-mJG (Guria et al., 2005 a) is used for the second problem. Simplified circuits with a few split streams are proposed on the basis of the present optimization study, which enhance the recovery of the acid-grade product without affecting its quality, for a given total volume of the flotation cell-bank. Even though the optimal solutions have certain drawbacks, they suggest a meaningful direction in using an iterative fitting of parameters to such optimal circuits, followed by re-optimization. Key words: Froth flotation, Mineral processing, Industrial fluorspar beneficiation, Feed identification, Circuit/network optimization, Global optimal, Jumping gene, Genetic algorithm, Multi-objective optimization

Jan 1, 2009

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By P. Groleau, O. Tavchandjian, D. Marcotte

In open pit mining, each small mining unit (SMU) is selected for mill processing based on an estimate of its true grade. The estimation is usually done using analyses of cuttings from blast holes within that SMU. One common estimator used for selection is the arithmetic average of within-SMU samples. This estimator is conditionally biased. The effect of a conditional bias is to overestimate the profit really recovered from the deposit. For this reason, a conditionally unbiased estimator is preferable. Increasing the number of samples generally improves the accuracy of the estimation (and diminishes the conditional bias, if present, of most estimators). However, there exists a practical limit where an additional sample does not improve the estimation sufficiently to cover the expense of making the analysis. This limit is specific to each deposit and depends on geostatistical parameters, economic factors, and mining parameters. This study examines how the number of samples affects the recovered reserves and the resulting profit. Also, the effects on optimal profit of varying the different factors are examined. Globally, the number of samples required increases with the selectivity of the operation. For a given ore deposit, the greater the number of SMUs selected for processing, the fewer samples are required and vice-versa.

Jan 1, 1998

Mr J. Meintjes (Chairman) was in the chair. There were also present: 7 Members: Messrs B. D. McNeice, A. Bain, G. E. Carlyon, C. H. Coxon, B. F. v. d. Merwe, A. C. Hofmeyer, H. J. R. Way. 4 Associate Members: Messrs E. J. Jackson, A. C. Melvill, W. Weber, R. E. Powell. 2 Visitors. It was decided to have the visit to ETC at Barberton on 20th March. A programme will be sent to all members who indicated that they wish to go on this visit. A talk on "Billet Casting of Ferrochrome" was given by Mr. B. F. van der Merwe. After question time the chairman thanked the speaker and asked for the talk to be forwarded for possible publication in the Journal. The meeting closed at 9.10 p.m.

Jan 1, 1967

By G. B. Shea

"INTRODUCTION Much of the recent progress in increasing the efficiency of oil-well performance can be attributed to advancements in the art of cleaning wells. Through research and development by operators and service companies during the past decade, significant improvements in the application of engineering and chemical principles to well-cleaning technology have widened greatly the scope of ""clean-out"" methods to the end that greater ultimate recovery of oil will be attained.This report reviews recent improvements and developments on this important problem in California; it describes also the use of various methods and tools for cleaning wells to stimulate or revive their productivity. Developments in preventing and removing mud sheaths in well-completion operations also are described. The report is based on a field survey, supplemented by data from the technical and patent literature and from manufacturers' catalogs, which contain much valuable information.In preparing the material for publication as a Bureau of Mines report, the author has been fully aware of certain limiting conditions that attend the discussion of a subject such as that treated in this report. The following are examples:1. To a considerable extent, well cleaning in California is done with tools rented from service companies, and their representatives and employees are specialists in jobs of this type. They usually have working experience with their own equipment and methods which greatly exceeds that of persons whose interest has been casual or who have had no opportunity to study the subject in detail in actual practice. Many of the tools and methods are covered by letters patent for the protection that may be in developing and successfully applying these mechanical and chemical means of increasing the production of wells. Frequently several years have been required to perfect a given tool or technique, requiring relatively large investments to establish a service that is remunerative to those who have primary interest in a certain development and at the same time attractive enough to the operators of producing properties (because of greater quantities of oil delivered into the flow tanks) to warrant employment of or contractual agreements with a particular service group."

May 1, 1943

By Richard J. Mahany, Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission in metal/non-metal mines over a wide frequency range from 0.2 - 1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types include oil shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most important mining techniques. The results show that transmission at medium frequencies are optimum for wireless mine communications, in agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 8, 1981