Search Documents

In 2005, 14,666 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA).1 Almost half (48.5%) were sand and gravel mines, followed by stone mines (30.6%), coal mines (14.1%), nonmetal mines (5.0%), and metal mines (1.8%).

Jan 1, 2008

By R. August Heindl

A process for recovering manganese from open-hearth steel-plant slags was investigated. The proposed method of accomplishing this is indicated by the flow diagram in figure 1. Mixtures of open-hearth, steel-plant flush slags and limestone, so proportioned as to have molar [CaO -3P205] ratios of approximately 2, were fired at approximately 2,400° F. in an oxidizing atmosphere and then cooled slowly. This treatment produced a clinker consisting principally of two solid phases comprised of (1) various combinations of the oxides of manganese, iron, aluminum, and magnesium, probably in spinel complexes, and (2) a dicalcium silicate phase, which contains the phosphorus. Reduction of these clinkers with hydrogen or with gaseous mixtures containing CO, CH4, and other hydrocarbons at about 1,300° F. formed manganous oxide as well as varying amounts of ferrous oxide and iron. Carbon monoxide and mixtures of hydrogen and carbon monoxide effectively reduced the clinkers but also gave higher proportions of soluble iron when the manganese was extracted from the reduced clinkers by leaching at about 80° F. with ammonium carbonate solutions containing 26 to 28 percent ammonia and 15 to 26 percent carbon dioxide. It is believed that the manganese is in solution as an ammonia-manganese complex. Concentrations of about 90 grams of manganese per liter were obtained by batch countercurrent procedures. By distilling 50 percent of the ammonia, the ammonia-manganese complex was decomposed, and approximately 90 percent of the manganese was precipitated as the carbonate with the simultaneous precipitation of 15 to 30 percent of the iron, the larger amounts of iron precipitating in the continuous tests. The manganese-iron ratio in the product could be increased either by recycling more manganese from the distillation to the extraction or by aerating the liquor to purge it of iron before, rather than after, the distillation step. Calcination of the pelletized manganese carbonate in an oxidizing stmosphere at 2,000° F. or above gave a final product, Mn304, resistant to crushing and apparently possessing the other physical properties essential in a ferromanganese blast-furnace feed.

Jan 1, 1955

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that affects the net expansion of the change in both industrial and test ovens. Various test results have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; out no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors. While investigating the reactivity of cokes made by the BM-AGA method,6/ Reynolds7/ found that granular low-temperature cokes shrink considerably then reheated to higher temperatures. This shrinkage was large enough to influence the behavior of the charge (net expansion or contraction) in a coke oven to a marked extent. Since that time the Bureau of nines has investigated the shrinkage of coke different methods, all of thick had one common objective - the elimination of the effect of other factors, such as swelling in the plastic range, which could either partly or completely mask the shrinkage of the coke. Only parts of these studies have been published8/9/ in abbreviated form in]

Jan 1, 1940

By R J. Goldfarb, A B. Christie, D I. Groves

Small orogenic gold deposits have the same deposit-scale geological and geochemical features as those that characterise giant orogenic gold systems (>16 Moz Au). Therefore, a broader-scale approach is needed to identify the critical controls on giant deposits and their disproportionate distribution throughout time and space. Ages of giant gold systems cluster around well-defined periods of lithospheric growth at continental margins, and it is orogen-scale processes during these Late Archaean, Early Proterozoic and Phanerozoic times that determine gold endowment of a province.   A critical factor for giant orogenic gold provinces appears to be asthenospheric upwelling at the time of gold mineralisation to most effectively transfer the thermal energy required to initiate and sustain high hydrothermal fluid flux. The extent of this fluid flux should be related to thickness of the lithosphere beneath a province at the time of gold mineralisation, such that giant gold deposits are much more likely to develop in orogens with oceanic or thinned continental lithosphere. A proxy for the latter is likely to be a short premineralisation crustal history such that thick subcontinental lithospheric mantle was not developed. Conversely, orogens with protracted premineralisation crustal histories are more likely to have a thick subcontinental lithospheric mantle, which is difficult to delaminate and, hence, such provinces will normally be poorly endowed. The nature of the lithosphere also influences the intrinsic gold concentrations of potential source rocks, with back-arc basalts, transitional basalts and basanites enriched in gold relative to other rock sequences. Thus, segments of orogens with thin lithosphere may be defined by conjunction of giant-scale fluid flux through gold-enriched sequences.   Although the nature of the lithosphere plays the crucial role in dictating which orogenic gold provinces will contain one or more giant deposits, the precise siting of those giants depends on the critical conjunction of a number of province-scale factors that control fluid conduits, traps, and seals in tectonically and lithospherically suitable terranes within accretionary orogens.

Jan 1, 2005

By C. M. McKinney

The Bureau of Mines analyzed 626 crude oils from 546 oilfields in the United States that produced 2,500 BOPD or more during at least 1 of the last 3 years. Included also are crude oil analyses from eight fields that produced less but which were located in areas having few or no fields that produced 2,500 BOPD. The tables show the geographical and geological source, general characteristics. and determined and computed analytical data for each sample. The analyses were made according to the Bureau of Mines routine method and are directly comparable to other previously published analyses.

Jan 1, 1966

Jan 1, 1967

By M. Guney, A. R. Bell

In Mindola mine on the Zambian Copperbelt, there is a plan to extend the current production level of 1.2-1.5 km (3,900-4,900 ft) with five additional production levels. Research work indicated that the present total heat output of 38.6 MW will inevitably increase to 63.2 MW in 25 years. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 33.8/40.2°C (93/104°F) and 35.3142.10C (95/108°F) respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9, 000 MW.

Jan 3, 1984

By W. A. Lang

Introduction Under our present civilization, industrial developments will be greatest in those areas in which energy .can be most economically produced and efficiently used, where labour is in adequate supply, and where markets for the products of industry are available. A knowledge of fuels- the present major sources of energy- and of their utilization is therefore of vital importance. With that in mind, the aim in this paper will be to outline the known reserves of fuels in Alberta, to give their characteristics, to indicate the markets served by each, and to offer some suggestions for the future development of the coal industry. The paper should be regarded as a compilation of published data rather than as an original treatise. Alberta is richly blessed by having large reserves of mineral fuels. The estimated reserves of coal are 46,562 million tons. Alberta is the oil and gas province of Canada. The world's largest deposit of bituminous sand occurs along the Athabaska river in Alberta. In addition, there are large areas of forested land in the northern and western sections of the Province, and the rivers serve for the development of hydro-power.

Jan 1, 1949

Most processing plants use automatic samplers to extract ore aliquots along a producing shift. These aliquots are combined into a sample normally sent to lab analysis. The sampler used in the extraction of an aliquot from a continuous flow of ore, i.e. a belt conveyor is required to be both precise and accurate. Surprisingly, not all commercial automatic samplers exhibit these two mandatory properties. Consequently, it is recommended the development of a procedure able to check sample assays reproducibility obtained using a given sampling protocol. This paper uses the Gy’s sampling theory to evaluate coal quality control practices at a washing plant using an automatic sampler extracting coal increments from the ROM feeding belt conveyor. Gy’s theory provides the means to establish the precision limits for a given sampling protocol. Various ore properties are required to be determined in combination with sample mass and mass of the lot sampled. All this information leads to the definition of the precision limit. The precision limit obtained was checked via an experiment mimicking what happens in situations where both miner and consumer use the same and appropriate sampling practices. The experiment demonstrates that sampling theory precision limits were valid if unbiased samplers are used by both parties, i.e. miner and consumer. Keywords: sampling, quality control, coal

Jan 1, 2003

The overall objective of this study is to gather operational data from selected surface coal mining systems in the United States, and to assess the potential production and economic capacity of the systems. The study includes: four mines, each using a different mining technique and different equipment. One mine was selected from each of the major coal fields: Midwestern, eastern,, northwestern, and southwestern. The Midwestern Mine is located in the Central Plains and produced 1.45 million tons of raw coal during the study year The Midwestern Mine uses the area mining or box-cut technique. A large in-pit shovel and a bucket wheel excavator are used to remove the overburden. Coal is removed by a loading shovel and transported to the dumping point by large off--highway trucks.

Jan 1, 1975

By Rusdian F. Kayadoe, Michael B. Hutahaean, Sandi A. Firmanulhaq

Deep Mill Level Zone (DMLZ) mine is located in Papua, Indonesia operated by PT Freeport Indonesia (PTFI) with approximately 1,500m below surface. The ore body extend 1230m width from northwest to southeast by 300–400m length east-west. The mine currently produces at full production of 80,000 tons per day until 2041. Part of the extension of current active production block and mitigation sits 225 m above the production block 1 (PB1) and 2 (PB2A and PB2B) which located in 2590L, named production block#4 (PB4W and PB4E). As the mining continues at PB1N, PB2A, and PB2B, the cave growth vertically and laterally to south perimeter of the footprint affecting the integrity of PB4W/E footprint. Currently, PB1N and PB2N are in active production whilst PB4E development continues from South against PB1N cave, as can be seen in Figure 1. A slight overlapping between PB1E and PB4E intentionally to promote cave connections between the two caves. Despite low stress model in the PB4E near existing caves, the PB4E cave propagation expected by the large strain and will be propagating in tension failure to the PB1E cave. Hence, designing the drill drives edge and first drawbell location as close as possible to the PB1E cave is necessary to guarantee cave connection. Since PB4 footprint development commenced in December 2021, there have been a substantial cave propagation observed from existing downhole monitoring. As the PB4 footprint designed perpendicular to existing DMLZ PB1 cave, adjustment of the development edge design is necessary to reflect the progression the loosening zone propagation to the South. Final life of mine design for extraction, undercut and ventilation level were decided in October 2023 considering latest update cave (fractured/ yielded) boundary. Numerical model of potential rock mass damage also aids the decision to locate the drift edge design. Predicting the cave progression impact is critical to both production at the existing active blocks and development of the new area. The use of cave shape data from year 2021–2023 gives an insight of the cave shape estimation at the end of 2024 when the undercut drift will be developed. This paper presents actual cave growth of active production blocks and its relative vertical progression impact as the result of drawing in order to plan for acceptable rate and provide mitigation once the minimum acceptable rock mass condition and minimum pillar threshold achieved.

Feb 1, 2025

By Douglas F. Scott

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the Pyramid RARE II area (No. 5023) covering 23,500 acres (9,500 ha) of E1 Dorado National Forest and 7,900 acres (3,200 ha) of the Lake Tahoe Basin Management Unit (fig. 1). The Bureau of Mines investigation did not reveal mineral deposits in the area. Samples taken from silicified and limonite-stained metasedimentary rocks and aplite dikes were void of precious or base metals or uranium. Placer samples from stream gravels contained no gold values. Molybdenite occurs in quartz stringers within quartz monzonite near Grass Lake, adjacent to the area; no extension; were found in the area.

Jan 1, 1982

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967

By C. Braun, C. Kennedy, P. Katsabanis

A series of small scale tests, simulating multi-hole blasts have been performed to establish the effect of delays on blast fragmentation. The blasts were performed in high quality granodiorite blocks, which were cut from stone prepared by dimensional stone quarry operations. The pattern used was equilateral triangular, with a distance of 10.2cm between boreholes, which had a diameter of 11mm, were loaded with detonating cord and the coupling medium was water. The delays used were achieved using different lengths of detonating cord for the cases of delays between 0 and 100 microseconds between holes and a sequential blasting machine firing seismic detonators for larger delays up to 4ms. All fragments were collected and screened. The experiments showed that the coarsest fragmentation was achieved with simultaneous initiation of all charges. Fragmentation became finer with delay time between holes up to 1ms between holes. The results show that in moderate to competent rock, similar to the granodiorite of the experiments, fragmentation optimization requires delays of few milliseconds per meter of burden. In view of the findings, which agree with previous published work, the current trend of selecting fast firing times for fragmentation optimization is questioned.

Jan 1, 2006

By J Knoblauch, D, P J. J Strobos, C Foggo

The Sally Malay Project is located 120 km north of Halls Creek in the eastern Kimberley region. Since commissioning, ongoing improvements on the plant have resulted in recoveries now greatly exceeding the initial design targets. The continual optimisation endeavours of the Sally Malay metallurgy department included an automation project that was done in close collaboration with Mintek. In this team effort, several problem areas were addressed and the FloatStar advance control system was successfully commissioned to stabilise and optimise the flotation circuit. The remote location of the Kimberley Nickel Mines operation, fly-in, fly-out roster and the current mining boom makes the acquisition of experienced flotation staff difficult. The implementation of an automated flotation control system reduces this burden and contributes to the training of inexperienced staff. This paper illustrates not only the process control improvements achieved as a result of the installation of the FloatStarÖ advanced control system, but also how it has assisted operational personnel with their understanding of the process.

Jan 1, 2006

By Roger G. Long

This final report reviews installation, maintenance and inspection of mine pager telephone installations. A Technical Handbook was developed and distributed. Certain commercial telephone test equipment was modified and a tone source and switching circuit were developed for use in the testing of mine pager phone systems. Descriptions are included of the modifications to a commercial test set and of a tone source/ switching unit.

Jan 1, 1975

By S. A. Bortz

This report presents the results of an extensive laboratory testing program to determine the physical properties of shotcrete including the use of fast-set agents, controlled set cements, and both wet and dry shotcreting equipment. Shotcrete was placed under simulated field conditions using the dry and wet processes. Mechanical properties obtained for accelerated and nonaccelerated shotcretes include compressive, flexural, and shear strength, elastic modulus and Poisson's ratio, and shear and tensile properties of shotcrete bonded to coal, sandstone, and shale. Physical properties measured were unit weight and permeability to methane gas. The data show that rapid setting shotcrete has the potential for improved coal mine ground control. There is no clear evidence that either wet or dry process shotcrete is superior to the other; however, indications are that regulated set cement is preferred to cement containing fast-setting admixtures.

Jan 1, 1973

By J. Murray Riddell, Grover J. Holt, Arthur E. Anderson

Out of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in Pow gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1940

By J. Murray Riddell, Arthur E. Anderson, Grover J. Holt

Out of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in Pow gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1940

By Deborah A. Peacock

"Outer space technology and exploration have reached a tipping point, so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies worldwide are on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3.The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars.How and why are the Moon and asteroids and their resources of interest to private space industry companies? Why are the Moon and asteroids viewed as a potential business venue?Geology of the Moon and asteroids — Why do we want to mine there?Space enterprises are actively working toward establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products and distribution of the products and services in space and to Earth and beyond2.Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral-rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind."

Jan 1, 2017