Search Documents

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include better fire suppression systems, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By Ernest M. Spokes

Maximum fan efficiency can only be obtained when the fan has the correct combination of size, speed, and blade setting to provide the required flow of air against the mine resistance. As the mine grows older, resistance decreases unless old workings flow is restricted, and new combinations of speed and blade setting or different fan sizes may provide greater economy.

Jan 1, 1977

By E. C. Lane

"INTRODUCTION The first important discovery of petroleum in New Mexico was near Dayton, Eddy County, where the Brown well was drilled in 1909, and small quantities of oil were produced. In 1911 and 1912 wells were drilled in McKinley County, but commercial production did not begin until the discovery of the Hogback field, San Juan County, in 1922. The discovery well in the Artesia field, Eddy County, drilled in 1923, gave impetus to active drilling in many areas. Since 1924 New Mexico has produced petroleum in commercial quantities and since 1930 the State has joined the ranks of the big produc¬ing States, being sixth or seventh in total production in recent years.Production by years. 1924 to 1940, inclusive, taken from annual figures in Bureau of Mines Minerals Yearbook, are given in table 1. The total production shown is 274,331,000 barrels. Andreas 3/ has published production figures for the year 1940 and a resume of all production to the end of 1940. Data from his report are presented in table 2 for each field sampled. The cumulative production, as given by Andreas, is 270,618,575 barrels."

Aug 1, 1942

By Paul D. Merica

This year of 1926 marks the 40th. anniversary of nickel mining in Canada. Although the first nickel mine of the Sudbury basin was discovered in 1883, it was not until 1886 that the Canadian Copper Company was organized and actually began to mine copper-nickel ore from the Lady McDonald, Stobie and Evans mines. The intervening years have witnessed some exceedingly interesting nickel history, particularly interesting and gratifying as well to Canadians. Forty years ago, at the inception of Canadian nickel mining, the world's consumption of that metal was about 1000 tons per annum and this was supplied largely from New Caledonia ores refined in France. This nickel was used principally for the production of nickel-silver, coinage alloys, and for nickel-plating. No processes were then known for refining the Sudbury ores nor for the separation of copper from nickel. Consequently, the pioneers in Canadian nickel mining faced the double problem of finding a method of treating their ores, and of finding a market for the nickel when and if they could extract it.

Jan 1, 1926

By R. J. Burgess

During World War II the shortage of ore revived interest in eastern iron deposits, among which -!2..c "Ile Massachusetts and Connecticut limonites. The Cheever mine, in the Richmond-Salisbury area of Massachusetts, was formerly a large producer of limonite ere. The Bureau of Mines investigated the lateral and downward extensions of the Cheever ore body, which was mined from about 1850 to 1892, by ap open cut 1,000 feet long and also by underground workings. even holes aggregating 1,723 feet, were drilled by the Bureau during the winter of 1943-44. They comprised three diamond-core drill holes, two churn-drill holes, and two rotary-drill holes. A geophysical survey of the Cheever mine area and adjoining ground was made in conjunction with the drilling program. Although this survey did not locate the limonite ore beds, the data were of considerable assistance in locating the limestone contact which forms the footwall of the ore beds. Drilling disclosed two beds of limonite with a heavy overburden of glacial till.

Jan 1, 1949

For 11 years, under authorization of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C. 321-325), and amendments, the Bureau of Mines has carried on an extensive research and development program to establish methods for producing oil from coal and from oil shale. This act was passed by the 78th Congress primarily because of the stress of wartime demands for liquid fuels to supply our armed forces during World War II. The act was progressively extended by the 80th and 81st Congresses, as later peace-time demand for oil and oil products continued to increase.

Jan 1, 1956

In 2005, a total of 263 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining commodity sector, comprising 1.8% of all mining operations. ? Gold mines comprised 46.0% (n=121) of all metal mining operations. Other common types of metal mines were iron ore (n=32; 12.2%), copper ore (n=31; 11.8%), and lead and/or zinc ore (n=16; 6.1%). ? Nevada had the largest number of metal mines (n=52; 19.8%), followed by Alaska (n=27; 10.3%).

Jan 1, 2008

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By J. R. Thoenen

In Progress Rerort 1,4/ a number of facto were demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By H. H. Schrenk

One phase of Bureau of lines work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that devices embodying these features will be available the Bureau has established schedules of minimum requirements for oxygen breathing apparatus, gas masks4/, supplied-air respirators (hose mask, air-line respirators, and abrasive blasting helmet hoods, or masks)5/, and dispersoid (dust, fume and mist) respirators6/. Approval test, of oxygen¬-breathing apparatus are conducted by the Safety Division; approval tests of other types of respiratory protective equipment are conducted by the Health Division. These divisions comprise the Health and Safety Branch.

Jan 1, 1941

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By Charles Janin, HENNEN JENNINGS

Many articles have been written on the general principles and details of gold dredging, a but it is not possible within the limits of this paper to recapitulate them, and it is thus necessary to assume some knowledge of this literature by the readers of this paper. Although the purpose of this paper is to describe gold dredging in Montana, a brief mention of some early appliances used in New Zealand, Australia, and California may serve as a world-connecting link in our consideration of the development of gold dredging. DREDGES EARLY USED IN NEW ZEALAND, AUSTRALIA, AND CALIFORNIA. Spoon dredges operated by hand were tried in New Zealand on rich spots in the Clutha River with some success as early as 1865. A dredge of this kind is shown in Plate I, A. In 1870 a modification of the spoon, operated by steam and being thus a primitive steamshovel dredge, was worked in New Zealand. Steam-shovel dredging was attempted in California as early as 1888 and 1893, and with some success in later years. The elevator gold dredge with endless bucket chain was put into operation in New Zealand in 1882. Plate I, B, illustrates a type of this dredge operated by current wheels. Plate II, A, shows a steam-operated dredge of this class, also started in 1882. In 1897 R. H. Postlethwaite, connected with the Risdon Iron Works, San Francisco, introduced the dredging practice of New Zealand into California. The first dredge built sank in the turbulent current of the Yuba. The second at Oroville, owned and operated by W. P. Hammon, proved effective and was the start in California of successful gold dredging. Since then the growth of the golddredging industry in California has been so rapid that the gold output from dredges in that State exceeds that of all other States in the Union, and, in fact, of any other country of the world, the value of the gold produced in California by dredging from 1897 to the end of 1914 having been about $71,000,000.

Jan 1, 1916

Professor N. S. Budavari holds a Dip!. Min. Eng. from the Technical University of Sopr on, Hungary, and a Ph.D. degree from the University of Newcastle-upon-Tyne, U.K. Mr J. J. Geldenhuys, Pr. Eng., is Divisional Manager Mining of Anglovaal Limited, being in charge of Prieska Copper Mines (Pty) Limited, Loraine Gold Mines, Limited, and Village Main Reef Gold Mining Company Limited.

Jan 1, 1983

By R. R. Sayers

Although the attention of those interested in diseases peculiar to mining as teen focused recently on one duct disease - silicosis - other respiratory diseases may cause more suffering and economic loss. The increased incidence of these diseases usually is attributed to exposure to abnormal air conditions underground, such as sudden changes from high to low temperatures, excessive dust, and noxious gases. The principal respiratory diseases to which the mine is subject axe bronchitis, influenza and pneumonia, pulmonary tuberculosis, anthracosilicosis, and. silicosis. Although the mortality statistics in some of the tables included in this paper are old they have been corroborated by later, lees complete data Bronchitis Bronchitis is en inflammation of the bronchial tubes due, among other causes, to the inhalation of irritants such as dusts (organic and inorganic). Occupations that entail exposure to atmospheres polluted, by irritating gases carry with them the risk of bronchitis. According to Collie (1), it cannot be distinguished clinically from bronchitis occurring among the general population, and its association with tae inhalation of dust or gases usually is unrecognized.

Jan 1, 1941

By J. R. Thoenen

This circular is the second of a series presenting methods employed in solving the technical problems encountered in the production of sand and gravel. The first paper3 discussed the methods use in prospecting and exploration. This one teals with the problems involved in bringing a raw prospect to the production stage and considers the various methods of development and the Factors affecting that development. Later publications are planned to present and discuss methods of recovery and treatment. The recovery of sand and ravel from natural deposits and their preparation for market involve a progressive sequence of operating steps or processes. Each step or process presents its own peculiar problems which require different angles of mental approach, methods, and tools, but all are more or less dependent on the step or process which precedes or follows.

Jan 1, 1933

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980

By Willem P. C. Duyvesteyn

"Scandium International Mining Corp (SCY) has been involved in the commercial development of its Nyngan Scandium Project for about ten years. Various studies at a variety of global R&D organizations have been carried out in an attempt to define the deportment of scandium in both the limonite as well as the saprolite phases of Nyngan ore to assist with process development. Technologies such as sulfuric acid baking, high pressure acid leaching, sulfuric and hydrochloric acid atmospheric leaching and heap leaching have been extensively investigated both at the bench and pilot scale level to arrive at the most economic process flow sheet that will be discussed in some detail in this paper. Solvent extraction, ion exchange and other refining technologies have been tested and an optimum configuration has been established for the Nyngan project which is expected to be the first primary scandium mine and metallurgical plant in the world.Because of a lack of product availability the current scandium market is limited to less than 20 tons per year. Technologies have been identified to produce product with different specifications for aluminum alloys and solid oxide fuel cell applications. Preliminary economics have identified that Nyngan will be a robust and low capital cost project that can readily be expanded as the size of the scandium market increases."

Jan 1, 2016

By Young C. Kim

Introduction and Objective of This Paper Computerized open pit mine models* are more and more used today for feasi¬bility studies as well as for long range mine planning. In fact, using these models is becoming an enforced practice due to various reasons. One main reason is its capacity to evaluate several designs in a fraction of time required by manual effort. Another reason is the necessity to evaluate several. pit designs due to ever decreasing grade of the orebody and increasing financial risk due to smaller profitability margin. In spite of today's accepted use of computer models, very little guidelines are available which the average practitioner can follow either to choose or to build the type of model best suited for his need. Consequently, the objectives of this paper are: 1. To review the current state of the art in the computerized open pit mine models. 2. To provide some suggestions for model selection. 3. To share our experiences in developing a model for a highly irregular copper ore deposit (see Appendix).

Jan 1, 1977

By Golding S. D, Price P. L

The Early Permian Aldebaran Sandstone is the main hydrocarbon reservoir in the Denison Trough. Contained hydrocarbon gas has a wet gas index (C1/CI - C4) of between 0.87 and 0.97 (N=10), and constituent methane has 813CPDB values ranging from -51.5 to -36.2% (N=10). These values clearly indicate that the gas is thermogenic rather than biogenic. Considering the predominantly humic nature and maturity of all organic source material for the gas, the methane 813C values are anomalously low, with typical values for humic methane present in natural gas formed at similar maturity levels significantly higher at -26 ¦ 5%o. This suggests that, in addition to disseminated organic matter in underlying marine mudrocks of the Cattle Creek Formation, methane substantially more depleted in 13C was derived from coal seams of the Reids Dome beds, a thick coal measure sequence which underlies the Cattle Creek Formation and, in the south, the Aldebaran Sandstone. This methane is likely to have S13C values of between -75 and -40 oo, based on the known isotopic composition of dry gas trapped in humic coals of similar rank in the Sydney Basin and elsewhere in the Bowen Basin. In addition to the low methane S13C values, the contribution of coal seam methane would explain the fact that, (1) methane S13C values do not show the normal increase with decreasing gas wetness, and (2)013C%o (ethane-methane) values do not show the expected decrease with decreasing gas wetness. The presence of co-existing, isotopically heavy CO2 (S13C = +2.0 to +3.4%0, N=3) in the Glentulloch and Merivale Fields is consistent with the view that natural gas in the Aldebaran Sandstone is in part coal seam derived.

Jan 1, 1991

By L. C. IlsLey

The theory and practice followed by the Bureau of ones in the investigation of electrical equipment4/ made for service in massy mines are of particular interest not only to manufacturers but also to those organizations that deal with safety and inspection at the mines. This publication proposes to discuss the theory, upon which tests of equipment in explosive atmospheres are based and to consider inspection and other matters pertaining to investigations made bar the Bureau in ascertaining whether a machine merits approval.

Jan 1, 1941